Antibody Microarray for E. coli O157:H7 and Shiga Toxin in Microtiter Plates.

Antibody microarray is a powerful analytical technique because of its inherent ability to simultaneously discriminate and measure numerous analytes, therefore making the technique conducive to both the multiplexed detection and identification of bacterial analytes (i.e., whole cells, as well as associated metabolites and/or toxins). We developed a sandwich fluorescent immunoassay combined with a high-throughput, multiwell plate microarray detection format. Inexpensive polystyrene plates were employed containing passively adsorbed, array-printed capture antibodies. During sample reaction, centrifugation was the only strategy found to significantly improve capture, and hence detection, of bacteria (pathogenic Escherichia coli O157:H7) to planar capture surfaces containing printed antibodies. Whereas several other sample incubation techniques (e.g., static vs. agitation) had minimal effect. Immobilized bacteria were labeled with a red-orange-fluorescent dye (Alexa Fluor 555) conjugated antibody to allow for quantitative detection of the captured bacteria with a laser scanner. Shiga toxin 1 (Stx1) could be simultaneously detected along with the cells, but none of the agitation techniques employed during incubation improved detection of the relatively small biomolecule. Under optimal conditions, the assay had demonstrated limits of detection of ~5.8 × 105 cells/mL and 110 ng/mL for E. coli O157:H7 and Stx1, respectively, in a ~75 min total assay time.

Mathematical modeling of growth of non-O157 Shiga toxin-producing Escherichia coli in raw ground beef.

UNLABELLED: The objective of this study was to investigate the growth of Shiga toxin-producing Escherichia coli (STEC, including serogroups O45, O103, O111, O121, and O145) in raw ground beef and to develop mathematical models to describe the bacterial growth under different temperature conditions. Three primary growth models were evaluated, including the Baranyi model, the Huang 2008 model, and a new growth model that is based on the communication of messenger signals during bacterial growth. A 5 strain cocktail of freshly prepared STEC was inoculated to raw ground beef samples and incubated at temperatures ranging from 10 to 35 °C at 5 °C increments. Minimum relative growth (<1 log10 cfu/g) was observed at 10 °C, whereas at other temperatures, all 3 phases of growth were observed. Analytical results showed that all 3 models were equally suitable for describing the bacterial growth under constant temperatures. The maximum cell density of STEC in raw ground beef increased exponentially with temperature, but reached a maximum of 8.53 log10 cfu/g of ground beef. The specific growth rates estimated by the 3 primary models were practically identical and can be evaluated by either the Ratkowsky square-root model or a Belehrádek-type model. The temperature dependence of lag phase development for all 3 primary models was also developed. The results of this study can be used to estimate the growth of STEC in raw ground beef at temperatures between 10 and 35 °C. PRACTICAL APPLICATION: Incidents of foodborne infections caused by non-O157 Shiga toxin-producing Escherichia coli (STEC) have increased in recent years. This study reports the growth kinetics and mathematical modeling of STEC in ground beef. The mathematical models can be used in risk assessment of STEC in ground beef.

Genotypes and toxin gene profiles of Staphylococcus aureus clinical isolates from China.

A total of 108 S. aureus isolates from 16 major hospitals located in 14 different provinces in China were characterized for the profiles of 18 staphylococcal enterotoxin (SE) genes, 3 exfoliatin genes (eta, etb and etd), and the toxic shock syndrome toxin gene (tsst) by PCR. The genomic diversity of each isolate was also evaluated by pulsed-field gel electrophoresis (PFGE), multilocus sequence typing (MLST), and accessory gene regulator (agr) typing. Of these strains, 90.7% (98/108) harbored toxin genes, in which tsst was the most prevalent toxin gene (48.1%), followed by sea (44.4%), sek (42.6%) and seq (40.7%). The see and etb genes were not found in any of the isolates tested. Because of high-frequency transfer of toxin gene-containing mobile genetic elements between S. aureus strains, a total of 47 different toxin gene combinations were detected, including a complete egc cluster in 19 isolates, co-occurrence of sea, sek and seq in 38 strains, and sec and sel together in 11 strains. Genetic typing by PFGE grouped all the strains into 25 clusters based on 80% similarity. MLST revealed 25 sequence types (ST) which were assigned into 16 clonal complexes (CCs) including 2 new singletons. Among these, 11 new and 6 known STs were first reported in the S. aureus strains from China. Overall, the genotyping results showed high genetic diversity of the strains regardless of their geographical distributions, and no strong correlation between genetic background and toxin genotypes of the strains. For genotyping S. aureus, PFGE appears to be more discriminatory than MLST. However, toxin gene typing combined with PFGE or MLST could increase the discriminatory power of genotyping S. aureus strains.

High-throughput biosensors for multiplexed food-borne pathogen detection.

Incidental contamination of foods by pathogenic bacteria and/or their toxins is a serious threat to public health and the global economy. The presence of food-borne pathogens and toxins must be rapidly determined at various stages of food production, processing, and distribution. Producers, processors, regulators, retailers, and public health professionals need simple and cost-effective methods to detect different species or serotypes of bacteria and associated toxins in large numbers of food samples. This review addresses the desire to replace traditional microbiological plate culture with more timely and less cumbersome rapid, biosensor-based methods. Emphasis focuses on high-throughput, multiplexed techniques that allow for simultaneous testing of numerous samples, in rapid succession, for multiple food-borne analytes (primarily pathogenic bacteria and/or toxins).

A multiplex real-time polymerase chain reaction for simultaneous detection of Salmonella spp., Escherichia coli O157, and Listeria monocytogenes in meat products.

To achieve an effective detection of Salmonella spp., Escherichia coli O157, and Listeria monocytogenes in meat products, a multiplex real-time polymerase chain reaction (PCR) coupled with a multipathogen enrichment strategy was developed in this study. Pathogen-specific DNA sequences in the invA, rfbE, and hlyA genes were employed to design primers and TaqMan probes for identifying Salmonella spp., E. coli O157, and L. monocytogenes, respectively. An internal amplification control (IAC) utilizing a novel DNA sequence from human adenovirus was incorporated into the multiplex PCR assay to indicate false-negative results. Concurrent amplifications of multiple targets and IAC were thoroughly evaluated and optimized to minimize PCR competitions. Combined with a multipathogen enrichment in a selective enrichment broth for Salmonella, Escherichia, and Listeria (SEL), the multiplex real-time PCR assay was able to simultaneously detect all of the three organisms in artificially contaminated ground beef at a detection sensitivity of <18 CFU/10 g ground beef. Applying the assay to 26 retail meat samples including beef, chicken, turkey, and pork revealed that 12 samples were positive for one of the organisms and 3 samples were positive for two of the organisms after a 20-h enrichment in SEL. The remaining meat samples tested negative for all of the organisms by only showing amplification of the IAC. These results were confirmed by traditional culture methods testing for each individual species. Taken together, the multiplex real-time PCR assay combined with multipathogen enrichment is a rapid and reliable method for effectively screening single or multiple pathogen occurrences in various meat products.

A real-time PCR method for the detection of Salmonella enterica from food using a target sequence identified by comparative genomic analysis.

A 5'-nuclease real-time PCR assay using a minor groove binding probe was developed for the detection of Salmonella enterica from artificially contaminated foods. S. enterica-specific sequences were identified by a comparative genomic approach. Several species-specific target sequences were evaluated for specificity. A real-time PCR assay was developed targeting a nucleotide sequence within the putative type III secretion ATP synthase gene (ssaN). An internal amplification control (IAC) probe was designed by randomly shuffling the target probe sequence and a single-stranded oligonucleotide was synthesized to serve as an IAC. The assay demonstrated 100% inclusivity for the 40 Salmonella strains tested and 100% exclusivity for 24 non-Salmonella strains. The detection limit of the real-time PCR assay was 41.2 fg/PCR with Salmonella Typhimurium genomic DNA and 18.6 fg/PCR using Salmonella Enteritidis genomic DNA; 8 and 4 genome equivalents, respectively. In the presence of a natural background flora derived from chicken meat enrichment cultures, the sample preparation and PCR method were capable of detecting as few as 130 Salmonella cfu/mL. Using the developed real-time PCR method to detect Salmonella in artificially contaminated chicken, liquid egg and peanut butter samples, as few as 1 cfu/10 g of sample was detectable after a brief (6h) non-selective culture enrichment.

Development of an oligonucleotide-based microarray to detect multiple foodborne pathogens.

Escherichia coli O157:H7, Salmonella enterica, Listeria monocytogenes and Campylobacter jejuni are considered important pathogens causing the most food-related human illnesses worldwide. Current methods for pathogen detection have limitations in the effectiveness of identifying multiple foodborne pathogens. In this study, a pathogen detection microarray was developed using various 70-mer oligonucleotides specifically targeting the above pathogens. To reduce the cost of detection, each microarray chip was designed and fabricated to accommodate 12 identical arrays which could be used for screening up to 12 different samples. To achieve high detection sensitivity and specificity, target-specific DNA amplification instead of whole genome random amplification was used prior to microarray analysis. Combined with 14-plex PCR amplification of target sequences, the microarray unambiguously distinguished all 4 pathogens with a detection sensitivity of 1 x 10(-4) ng (approximately 20 copies) of each genomic DNA. Applied the assay to 39 fresh meat samples, 16 samples were found to be contaminated by either 1 or 2 of these pathogens. The co-occurrences of Salmonella and E. coli O157:H7, Salmonella and L. monocytogenes in the same meat samples were also observed. Overall, the microarray combined with multiplex PCR method was able to effectively screen single or multiple pathogens in food samples and to provide important genotypic information related to pathogen virulence.

Evanescent wave fiber optic biosensor for salmonella detection in food.

Salmonella enterica is a major food-borne pathogen of world-wide concern. Sensitive and rapid detection methods to assess product safety before retail distribution are highly desirable. Since Salmonella is most commonly associated with poultry products, an evanescent wave fiber-optic assay was developed to detect Salmonella in shell egg and chicken breast and data were compared with a time-resolved fluorescence (TRF) assay. Anti-Salmonella polyclonal antibody was immobilized onto the surface of an optical fiber using biotin-avidin interactions to capture Salmonella. Alexa Fluor 647-conjugated antibody (MAb 2F-11) was used as the reporter. Detection occurred when an evanescent wave from a laser (635 nm) excited the Alexa Fluor and the fluorescence was measured by a laser-spectrofluorometer at 710 nm. The biosensor was specific for Salmonella and the limit of detection was established to be 10(3) cfu/mL in pure culture and 10(4) cfu/mL with egg and chicken breast samples when spiked with 10(2) cfu/mL after 2-6 h of enrichment. The results indicate that the performance of the fiber-optic sensor is comparable to TRF, and can be completed in less than 8 h, providing an alternative to the current detection methods.

Capture of Escherichia coli O157:H7 Using Immunomagnetic Beads of Different Size and Antibody Conjugating Chemistry.

Immunomagnetic beads (IMB) were synthesized using anti-Escherichia coli O157 antibodies and magnetic beads of two different sizes (1 µm and 2.6 to 2.8 µm) that contained a streptavidin coating, activated carboxyl groups or tosylated surfaces. The synthesized IMB, together with a commercially available IMB, were used to capture different strains of E. coli O157:H7 and E. coli O157:NM. The E. coli capture was measured by the time resolved fluorescence (TRF) intensity using a sandwich assay which we have previously demonstrated of having a sensitivity of 1 CFU/g after 4.5 hour enrichment [1]. The analyses of measured TRF intensity and determined antibody surface concentration indicated that larger beads provided higher response signals than smaller beads and were more effective in capturing the target of interest in pure culture and ground beef. In addition, while each type of IMB showed different favorable capture of E. coli O157:H7, streptavidin-coated IMB elicited the highest response, on average. Streptavidin-coated IMB also provided an economic benefit, costing less than $0.50 per assay. The results could be used to guide the proper choice of IMB for applications in developing detection processes for E. coli O157:H7.

Apparent thixotropic properties of saline/glycerol drops with biotinylated antibodies on streptavidin-coated glass slides: implications for bacterial capture on antibody microarrays.

The thixotropic-like properties of saline/glycerol drops, containing biotinylated capture antibodies, on streptavidin-coated glass slides have been investigated, along with their implications for bacterial detection in a fluorescent microarray immunoassay. The thixotropic-like nature of 60:40 saline-glycerol semisolid droplets (with differing amounts of antibodies) was observed when bacteria were captured, and their presence detected using a fluorescently-labeled antibody. Semisolid, gel-like drops of biotinylated capture antibody became liquefied and moved, and then returned to semisolid state, during the normal immunoassay procedures for bacterial capture and detection. Streaking patterns were observed that indicated thixotropic-like characteristics, and this appeared to have allowed excess biotinylated capture antibody to participate in bacterial capture and detection. When developing a microarray for bacterial detection, this must be considered for optimization. For example, with the appropriate concentration of antibody (in this study, 0.125 ng/nL), spots with increased diameter at the point of contact printing (and almost no streaking) were produced, resulting in a maximal signal. With capture antibody concentrations greater than 0.125 ng/nL, the excess biotinylated capture antibody (i.e., that which was residing in the three-dimensional, semisolid droplet space above the surface) was utilized to capture more bacteria. Similarly, when the immunoassay was performed within a hydrophobic barrier (i.e., without a coverslip), brighter spots with increased signal were observed. In addition, when higher concentrations of cells (∼10(8) cells/mL) were available for capture, the importance of unbound capture antibody in the semisolid droplets became apparent because washing off the excess, unbound biotinylated capture antibody before the immunoassay was performed reduced the signal intensity by nearly 50%. This reduction in signal was not observed with lower concentrations of cells (∼10(6) cells/mL). With increased volumes of capture antibody, abnormal spots were visualized, along with decreased signal intensity, after bacterial detection, indicating that the increased droplet volume detrimentally affected the immunoassay.

An antibody microarray, in multiwell plate format, for multiplex screening of foodborne pathogenic bacteria and biomolecules.

Intoxication and infection caused by foodborne pathogens are important problems worldwide, and screening tests for multiple pathogens are needed because foods may be contaminated with multiple pathogens and/or toxic metabolites. We developed a 96-well microplate, multiplex antibody microarray method to simultaneously capture and detect Escherichia coli O157:H7 and Salmonella enterica serovar Typhimurium (S. typhimurium), as well as a biomolecule (chicken immunoglobulin G or IgG employed as a proteinaceous toxin analog) in a single sample. Microarrayed spots of capture antibodies against the targeted analytes were printed within individual wells of streptavidin-coated polystyrene 96-multiwell microtiter plates and a sandwich assay with fluorescein- or Cy3-labeled reporter antibodies was used for detection. (Printing was achieved with a conventional microarray printing robot that was operated with custom-developed microplate arraying software.) Detection of the IgG was realized from ca. 5 to 25 ng/mL, and detection of E. coli O157:H7 and S. typhimurium was realized from ca. 10(6) to 10(9) and ca. 10(7) to 10(9) cells/mL, respectively. Multiplex detection of the two bacteria and the IgG in buffer and in culture-enriched ground beef filtrate was established with a total assay (including detection) time of ca. 2.5 h. Detection of S. typhimurium was largely unaffected by high concentrations of the other bacteria and IgG as well as the ground beef filtrate, whereas a small decrease in response was observed for E. coli O157:H7. The multiwell plate, multiplex antibody microarray platform developed here demonstrates a powerful approach for high-throughput screening of large numbers of food samples for multiple pathogens and toxins.

SPR biosensor for the detection of L. monocytogenes using phage-displayed antibody.

Whole cells of Listeria monocytogenes were detected with a compact, surface plasmon resonance (SPR) sensor using a phage-displayed scFv antibody to the virulence factor actin polymerization protein (ActA) for biorecognition. Phage Lm P4:A8, expressing the scFv antibody fused to the pIII surface protein was immobilized to the sensor surface through physical adsorption. A locally constructed fluidics system was used to deliver solutions to the compact, two-channel SPREETA sensor. Specificity of the sensor was tested using common food-borne bacteria and a control phage, M13K07 lacking the scFv fusion on its coat protein. The detection limit for L. monocytogenes whole cells was estimated to be 2 x 10(6)cfu/ml. The sensor was also used to determine the dissociation constant (Kd) for the interaction of phage-displayed scFv and soluble ActA in solution as 4.5 nM.

Detect of Escherichia coli O157:H7 in ground beef samples using piezoelectric excited millimeter-sized cantilever (PEMC) sensors.

Piezoelectric-excited millimeter-sized cantilever (PEMC) sensors consisting of a piezoelectric and a borosilicate glass layer with a sensing area of 4 mm2 were fabricated. An antibody specific to Escherichia coli (anti-E. coli) O157:H7 was immobilized on PEMC sensors, and exposed to samples containing E. coli O157:H7 (EC) prepared in various matrices: (1) broth, broth plus raw ground beef, and broth plus sterile ground beef without inoculation of E. coli O157:H7 served as controls, (2) 100 mL of broth inoculated with 25 EC cells, (3) 100 mL of broth containing 25 g of raw ground beef and (4) 100 mL of broth with 25 g of sterile ground beef inoculated with 25 EC cells. The total resonant frequency change obtained for the broth plus EC samples were 16+/-2 Hz (n=2), 30 Hz (n=1), and 54+/-2 Hz (n=2) corresponding to 2, 4, and 6h growth at 37 degrees C, respectively. The response to the broth plus 25 g of sterile ground beef plus EC cells were 21+/-2 Hz (n=2), 37 Hz (n=1), and 70+/-2 Hz (n=2) corresponding to 2, 4, and 6 h, respectively. In all cases, the three different control samples yielded a frequency change of 0+/-2 Hz (n=6). The E. coli O157:H7 concentration in each broth and beef samples was determined by both plating and by pathogen modeling program. The results indicate that the PEMC sensor detects E. coli O157:H7 reliably at 50-100 cells/mL with a 3 mL sample.

Antibody microarray detection of Escherichia coli O157:H7: Quantification, assay limitations, and capture efficiency.

A sandwich fluorescent immunoassay in a microarray format was used to capture and detect E. coli O157:H7. Here, we explored quantitative aspects, limitations, and capture efficiency of the assay. When biotinylated capture antibodies were used, the signal generated was higher (over 5-fold higher with some cell concentrations) compared to biotinylated protein G-bound capture antibodies. By adjusting the concentration of reporter antibody, a linear fluorescent response was observed from approximately 3.0 x 10(6) to approximately 9.0 x 10(7) cells/mL, and this was in agreement with the number of captured bacteria as determined by fluorescence microscopy. Capture efficiency calculations revealed that, as the number of bacteria presented for capture decreased, capture efficiency increased to near 35%. Optimization experiments, with several combinations of capture and reporter antibodies, demonstrated that the amount of bacteria available for capture (10(6) versus 10(8) cells/mL) affected the optimal combination. The findings presented here indicate that antibody microarrays, when used in sandwich assay format, may be effectively used to capture and detect E. coli O157:H7.

Comparison of enzyme-linked immunomagnetic chemiluminescence with U.S. Food and Drug Administration's Bacteriological Analytical Manual method for the detection of Escherichia coli O157:H7.

Escherichia coli O157:H7, a major foodborne pathogen, has been associated with numerous cases of foodborne illnesses. Rapid methods have been developed for the screening of this pathogen in foods in order to circumvent timely plate culture techniques. Unfortunately, many rapid methods are presumptive and do not claim to confirm the presence of E. coli O157:H7. The previously developed method, enzyme-linked immunomagnetic chemiluminescence (ELIMCL), has been improved upon to allow for fewer incidences of false positives when used to detect E. coli O157:H7 in the presence of mixed cultures. The key feature of this assay is that it combines the highly selective synergism of both anti-O157 and anti-H7 antibodies in the sandwich immunoassay format. This work presents application of a newly semi-automated version of ELIMCL to the detection of E. coli O157:H7 in pristine buffered saline yielding detection limits of approximately 1 x 10(5) to 1 x 10(6) of live cells/mL. ELIMCL was further demonstrated to detect E. coli O157:H7 inoculated into artificially contaminated ground beef at ca. 400 CFU/g after a 5 h enrichment and about 1.5 h assay time for a total detection time of about 6.5 h. Finally, ELIMCL was compared with USFDA's Bacteriological Analytical Manual method for E. coli O157:H7 in a double-blind study. Using McNemar's treatment, the two methods were determined to be statistically similar for the detection of E. coli O157:H7 in ground beef inoculated with mixed cultures of select bacteria.

Enzyme-linked immunomagnetic electrochemical detection of live Escherichia coli 0157:H7 in apple juice.

We describe the application of enzyme-linked immunomagnetic electrochemistry (ELIME) for the rapid detection of Escherichia coli O157:H7 in buffered apple juice. The ELIME technique entails sandwiching bacterial analyte between antibody-coated magnetic beads and an alkaline phosphatase-conjugated antibody. The beads (with or without bound bacteria) were localized onto the surface of magnetized graphite ink electrodes in a multiwell plate format. The enzyme substrate, 1-naphthyl phosphate, was added, and conversion of substrate to an electroactive product was measured using electrochemical detection. With this technique, detection of whole, live E. coli O157:H7 bacterial cells was achieved with a minimum detectable level of ca. 5 x 10(3) cells per ml in Tris-buffered saline or buffered apple juice in an assay time of ca. 80 min. With adjustment of pH, the ELIME response for the bacteria in either sampling medium was similar, indicating that apple juice components did not contribute to any discernible sample matrix effects.

Enzyme-linked immunomagnetic chemiluminescent detection of Escherichia coli O157:H7.

E. coli O157:H7 is a pathogenic microorganism that has been implicated in numerous cases of foodborne illnesses. A variety of rapid methods exist that show promise for the presumptive detection of this pathogen without the immediate need for incubating test samples for hours to days in microbial enrichment and culture media. In recent years, highly sensitive chemiluminescence has become a more affordable and portable detection method. Chemiluminescent detection has been coupled with the selectivity of antibodies, magnetic microparticle separation/isolation, and enzymatic signal amplification in order to develop a rapid method, termed enzyme-linked immunomagnetic chemiluminescence (ELIMCL). This work presents the application of ELIMCL to the detection of E. coli O157:H7 in pristine buffered saline with a detection limit of 7.6 x 10(3) for live cells in approx. 75 min assay time. The blocking agent casein and the surfactant Tween 20 were used to lower background luminescence and thus maximize signal-to-noise ratios. After 5.5 h of enrichment culture, ELIMCL was demonstrated to detect E. coli O157:H7 inoculated in ground beef at 10 CFU/g in a total assay time of about 7 h.

Blocking nonspecific adsorption of native food-borne microorganisms by immunomagnetic beads with iota-carrageenan.

We present herein the partitioning characteristics of anti-Salmonella and anti-Escherichia coli O157 immunomagnetic beads (IMB) with respect to the nonspecific adsorption of several nontarget food-borne organisms with and without an assortment of well-known blocking agents, such as casein, which have been shown to be useful in other immunochemical applications. We found several common food-borne organisms that strongly interacted with both types of IMB, especially with anti-Salmonella form (av DeltaG0=-20 +/- 4 kJ mol(-1)) even in the presence of casein [1% (w/v): DeltaG0=-18 +/- 3 kJ mol(-1); DeltaDeltaG0 approximately -2 kJ mol(-1)]. However, when one of the most problematic organisms (a native K12-like E. coli isolate; DeltaG0=-19 +/- 2 kJ mol(-1)) was tested for nonspecific binding in the presence of iota-carrageenan (0.03-0.05%), there was an average decline of ca. 90% in the equilibrium capture efficiency xi (DeltaG0=-11 +/- 4 kJ mol(-1); DeltaDeltaG0 approximately -8 kJ mol(-1)). Other anionic polysaccharides (0.1% kappa-carrageenan and polygalacturonic acid) had no significant effect (av DeltaG0=-19 +/- 1 kJ mol(-1); DeltaDeltaG0 approximately 0 kJ mol(-1)). Varying iota-carrageenan from 0% to 0.02% resulted in xi significantly diminishing from 0.69 (e.g., 69% of the cells captured; DeltaG0=-19 +/- 3 kJ mol(-1)) to 0.05 (DeltaG0=-11 +/- 2 kJ mol(-1); DeltaDeltaG0 approximately -9 kJ mol(-1)) at about 0.03% iota-carrageenan where xi leveled off. An optimum blocking ability was achieved with 0.04% iota-carrageenan suspended in 100 mM phosphate buffer. We also demonstrated that the utilization of iota-carrageenan as a blocking agent causes no great loss in the IMBs capture efficiency with respect to the capture of its target organisms, various salmonellae.