Photocatalytic H2 Production by Visible Light on Cd0.5Zn0.5S Photocatalysts Modified with Ni(OH)2 by Impregnation Method.

Nowadays, the study of environmentally friendly ways of producing hydrogen as a green energy source is an increasingly important challenge. One of these potential processes is the heterogeneous photocatalytic splitting of water or other hydrogen sources such as H2S or its alkaline solution. The most common catalysts used for H2 production from Na2S solution are the CdS-ZnS type catalysts, whose efficiency can be further enhanced by Ni-modification. In this work, the surface of Cd0.5Zn0.5S composite was modified with Ni(II) compound for photocatalytic H2 generation. Besides two conventional methods, impregnation was also applied, which is a simple but unconventional modification technique for the CdS-type catalysts. Among the catalysts modified with 1% Ni(II), the impregnation method resulted in the highest activity, for which a quantum efficiency of 15.8% was achieved by using a 415 nm LED and Na2S-Na2SO3 sacrificial solution. This corresponded to an outstanding rate of 170 mmol H2/h/g under the given experimental conditions. The catalysts were characterized by DRS, XRD, TEM, STEM-EDS, and XPS analyses, which confirmed that Ni(II) is mainly present as Ni(OH)2 on the surface of the CdS-ZnS composite. The observations from the illumination experiments indicated that Ni(OH)2 was oxidized during the reaction, and that it therefore played a hole-trapping role.

Kaolinite-urea complexes obtained by mechanochemical and aqueous suspension techniques--a comparative study.

Intercalation compounds of low- and high-defect kaolinites have been prepared by direct reaction with urea aqueous solution as well as by co-grinding with urea in the absence of water (mechanochemical intercalation). The complexes formed were studied by X-ray diffraction, thermal analysis, DRIFT spectroscopy, and scanning electron microscopy. In aqueous solution the degree of intercalation for the low- and high-defect kaolinites was found to be 77 and 65%, respectively. With mechanochemical intercalation, both kaolinites were almost fully expanded after 1 h of grinding. Based on the results of DRIFT spectroscopy, a structural model for the bonding of urea to the siloxane surface is proposed. The kaolinite-urea intercalation compounds produced by mechanochemical intercalation have crystallite sizes lower than those obtained by the aqueous solution method.

Mechanism for hydrotalcite decomposition: a controlled rate thermal analysis study.

The mechanism for the decomposition of hydrotalcite remains unsolved. Controlled rate thermal analysis enables this decomposition pathway to be explored. Hydrotalcites containing carbonate, vanadate and molybdate were prepared by coprecipitation. The resulting materials were characterised by XRD, simultaneous TG-DTG-DTA and controlled rate thermal analysis (CRTA) to determine the stability and thermal decomposition pathway of the synthesised hydrotalcites. For the carbonate intercalated hydrotalcite dehydration takes place in three steps two of which are quasi-isothermal and one non-isothermal. Dehydroxylation and decarbonation occur separately over the 235-330 and 330-370 degrees C temperature range. A second non-isothermal decarbonation step is observed in the 371-541 degrees C range. In comparison the mixed carbonate-vanadate and carbonate-molybdate hydrotalcites show two dehydration steps and the dehydroxylation and decarbonation occur simultaneously. The observation of three dehydration steps is used to support the model of water molecules in three structurally distinct environments in the hydrotalcite interlayer. CRTA technology provides a mechanism for the decomposition of hydrotalcites.

Investigation of mechanochemically modified kaolinite surfaces by thermoanalytical and spectroscopic methods.

The effect of mechanochemical activation (dry grinding), formamide intercalation, and thermal deintercalation on high- and low-defect kaolinite surfaces was studied by thermogravimetry and diffuse reflectance Fourier transform infrared spectroscopy. These investigations were completed with specific surface area and pore size distribution measurements. The surface acidity of the ground and the ground-and-intercalated kaolinites was probed with ammonia adsorption. The surface area and the pore volume as well as the amount of adsorbed ammonia increased with the rate of mechanochemical activation. At the same time the thermally deintercalated minerals showed increased surface area but decreased pore volume with the time of grinding. Adsorbed ammonia was detected as ammonium ion in the 1400-1500 cm(-1) spectral range.

Surface modification of mechanochemically activated kaolinites by selective leaching.

Low- and high-defect kaolinites mechanochemically activated for different periods of time have been treated with sulfuric acid solution. These modified materials were analyzed using a combination of X-ray diffraction, thermogravimetry, chemical analysis, diffuse reflectance Fourier transform infrared spectroscopy, as well as specific surface area and pore size distribution measurements. In addition to the mechanochemically amorphized part, the disordered and the adequately distorted phases also reacted with sulfuric acid. The specific surface areas of the leached samples of the partially or the completely amorphized materials were found to be greater than those of the thermally amorphized ones. The acid treatment results in a greater total pore volume for the partially amorphized materials than for the totally amorphized mineral. The partially amorphized high-defect kaolinite was proved to be more soluble than the low-defect kaolinite under similar conditions.

Identification of superactive centers in thermally treated formamide-intercalated kaolinite.

The thermal behavior of a formamide-intercalated mechanochemically activated (dry-ground) kaolinite was investigated by thermogravimetry-mass spectrometry (TG-MS) and diffuse reflectance Fourier transform infrared spectroscopy (DRIFT). After the removal of adsorbed and intercalated formamide, a third type of bonded reagent was identified in the temperature range 230-350 degrees C decomposing in situ to CO and NH3. The presence of formamide decomposition products, as well as CO2 and various carbonates identified by DRIFT spectroscopy, indicates the formation of superactive centers as a result of mechanochemical activation and heat treatment (thermal deintercalation). The structural variance of surface species decreases with the increase of grinding time. The unground mineral contains a small amount of weakly acidic and basic centers. After 3 h of grinding, the number of acidic centers increases significantly, while on further grinding the superactive centers show increased basicity. With the increase of grinding time and treatment temperature the number of bicarbonate- and bidentate-type structures decreases in favor of the carboxylate- and monodentate-type ones.