Effect of Photoactivation Timing on the Mechanical Properties of Resin Cements and Bond Strength of Fiberglass Post to Root Dentin.

OBJECTIVES: This study tested the hypothesis that photoactivation timing and resin cement affect mechanical properties and bond strength of fiberglass posts to root dentin at different depths. METHODS: Fiberglass posts (Exacto, Angelus) were luted with RelyX Unicem (3M ESPE), Panavia F 2.0 (Kuraray), or RelyX ARC (3M ESPE) using three photoactivation timings: light curing immediately, after three minutes, or after five minutes. Push-out bonding strength, PBS (n=10) was measured on each root region (coronal, middle, apical). The elastic modulus (E) and Vickers hardness (VHN) of the cement layer along the root canal were determined using dynamic indentation (n=5). A strain-gauge test was used to measure post-gel shrinkage of each cement (n=10). Residual shrinkage stress was assessed with finite element analysis. Data were analyzed with two-way analysis of variance in a split-plot arrangement and a Tukey test (α=0.05). Multiple linear regression analysis was used to determine the influence of study factors. RESULTS: The five-minute delay photoactivation timing significantly increased the PBS for all resin cements evaluated. The PBS decreased significantly from coronal to apical root canal regions. The mean values for E and VHN increased significantly with the delayed photoactivation for RelyX Unicem and decreased from coronal to apical root regions for all resin cements with the immediate-curing timing. CONCLUSIONS: The PBS of fiber posts to root dentin, E, and VHN values were affected by the root canal region, photoactivation timing, and resin cement type. Shrinkage stress values decreased gradually with delayed photoactivation for all the cements.

Incremental filling technique and composite material--part II: shrinkage and shrinkage stresses.

OBJECTIVES: Finite element analysis (FEA) was used to study polymerization shrinkage stress in molars restored with composites and to correlate those stresses with experimentally measured tooth deformation. METHODS: Three composites (Filtek LS, Aelite LS Posterior, Filtek Supreme) and three filling techniques (bulk, 2.0-mm increments, and 1.0-mm increments) for restoring a molar were simulated in a two-dimensional FEA. Polymerization shrinkage was modeled using post-gel shrinkage, which was measured using the strain gauge technique (n=10). Cuspal tooth deformation, measured at the buccal and lingual surfaces with strain gauges in a laboratory study, was used to validate the analysis. Residual shrinkage stresses were expressed in modified von Mises equivalent stresses. Linear Pearson correlations were determined between the laboratory and FEA results. RESULTS: Post-gel shrinkage values (in volume %) were: Filtek LS (0.11 ± 0.03) < Aelite LS Posterior (0.51 ± 0.02) < Filtek Supreme (0.62 ± 0.09). The 1.0-mm increment filling caused substantially higher stresses and strains in the cervical enamel region. Significant correlations were found between: elastic modulus and FEA strain, elastic modulus and FEA stress, post-gel shrinkage and FEA strain, post-gel shrinkage and FEA stress, FEA strain and cuspal deformation by strain gauge, and FEA stress and cuspal deformation by strain gauge (p<0.05). CONCLUSIONS: Increasing the number of increments and high post-gel shrinkage and/or elastic modulus values caused higher stresses in the remaining tooth structure and tooth/restoration interface. Cuspal deformation measured with the strain gauge method validated the finite element analyses.

Influence of resin cement and post configuration on bond strength to root dentine.

AIM: To evaluate the effect of luting agent and fibreglass post design on bond strength to root dentine at different depths within the canal. METHODOLOGY: Ninety single-rooted teeth were root filled and prepared to receive either a parallel-sided and serrated fibreglass post (Reforpost no. 2) or a tapered and smooth fibreglass post (Exato Cônico). The posts were cemented with the following resin cements: dual-cured resin cement (Rely X ARC), two self-adhesive resin cements (Rely X Unicem and MaxCem) and a self-cured resin cement (Cement-Post). The roots were cross-sectioned to obtain two 1-mm-thick discs for each cervical, middle and apical third of the prepared root portion. The posts were submitted to a micropush-out test at a speed of 0.5 mm min(-1), and the bond strength values (MPa) were submitted to anova in a split-plot arrangement and Tukey's test (P < 0.05). RESULTS: The RelyX Unicem demonstrated significantly higher bond strength values (P < 0.001) along the root dentine. The RelyX ARC and Cement-Post had similar bond strength values in the cervical third; however, the bond strength decreased significantly (P < 0.001) in an apical direction for the RelyX ARC. Significantly lower bond strength values (P < 0.001), irrespective of canal region, were found for MaxCem cement. The bond strength was similar for both post configurations irrespective of the resin cement and canal region. CONCLUSIONS: The retention of glass fibre posts remained unaffected by surface roughness but was influenced by resin cement type. The self-adhesive cement RelyX Unicem yielded a significantly greater (P < 0.001) bond strength value when cementing the fibreglass posts.