ABSTRACT
A new method for the synthesis and deposition of tungsten oxide nanopowders directly on the surface of a carbon-fiber-reinforced polymer composite (CFRP) is presented. The CFRP was chosen because this material has very good thermal and mechanical properties and chemical resistance. Also, CFRPs have low melting points and are transparent under ionized radiation. The synthesis is based on the direct interaction between high-power-density microwaves and metallic wires to generate a high-temperature plasma in an oxygen-containing atmosphere, which afterward condenses as metallic oxide nanoparticles on the CFRP. During microwave discharge, the value of the electronic temperature of the plasma, estimated from Boltzmann plots, reached up to 4 eV, and tungsten oxide crystals with a size between 5 nm and 100 nm were obtained. Transmission electron microscopy (TEM) analysis of the tungsten oxide nanoparticles showed they were single crystals without any extended defects. Scanning electron microscopy (SEM) analysis showed that the surface of the CFRP sample does not degrade during microwave plasma deposition. The X-ray attenuation of CFRP samples covered with tungsten oxide nanopowder layers of 2 µm and 21 µm thickness was measured. The X-ray attenuation analysis indicated that the thin film with 2 µm thickness attenuated 10% of the photon flux with 20 to 29 KeV of energy, while the sample with 21 µm thickness attenuated 60% of the photon flux.
ABSTRACT
The use of Fe films as multi-element targets in space radiation experiments with high-intensity ultrashort laser pulses requires a surface structure that can enhance the laser energy absorption on target, as well as a low concentration and uniform distribution of light element contaminants within the films. In this paper, (110) preferred orientation nanocrystalline Fe thin films with controlled morphology and composition were grown on (100)-oriented Si substrates by oblique angle RF magnetron sputtering, at room temperature. The evolution of films key-parameters, crucial for space-like radiation experiments with organic material, such as nanostructure, morphology, topography, and elemental composition with varying RF source power, deposition pressure, and target to substrate distance is thoroughly discussed. A selection of complementary techniques was used in order to better understand this interdependence, namely X-ray Diffraction, Atomic Force Microscopy, Scanning and Transmission Electron Microscopy, Energy Dispersive X-ray Spectroscopy and Non-Rutherford Backscattering Spectroscopy. The films featured a nanocrystalline, tilted nanocolumn structure, with crystallite size in the (110)-growth direction in the 15-25 nm range, average island size in the 20-50 nm range, and the degree of polycrystallinity determined mainly by the shortest target-to-substrate distance (10 cm) and highest deposition pressure (10-2 mbar Ar). Oxygen concentration (as impurity) into the bulk of the films as low as 1 at. %, with uniform depth distribution, was achieved for the lowest deposition pressures of (1-3) × 10-3 mbar Ar, combined with highest used values for the RF source power of 125-150 W. The results show that the growth process of the Fe thin film is strongly dependent mainly on the deposition pressure, with the film morphology influenced by nucleation and growth kinetics. Due to better control of film topography and uniform distribution of oxygen, such films can be successfully used as free-standing targets for high repetition rate experiments with high power lasers to produce Fe ion beams with a broad energy spectrum.
ABSTRACT
The livestock sector is one of the most important sectors of the agricultural economy due to an increase in the demand for animal protein. This increase generates serious waste disposal concerns and has negative environmental consequences. Furthermore, the food production chain needs phosphorus (P), which is listed as a critical raw material due to its high demand and limited availability in Europe. Manure contains large amounts of P and other elements that may be recycled, in the frame of circular economy and "zero waste" principles, and reused as a by-product for fertilizer production and other applications. This paper focuses on the extraction and recovery of amorphous silica from rice husk poultry litter ash. Two different extraction procedures are proposed and compared, and the obtained silica is characterized. This work shows that amorphous silica can be recovered as an almost pure material rendering the residual ash free of P. It also addresses the possibility of more specific phosphorous extraction procedures via acid leaching.
ABSTRACT
Single-phase Ce3+-doped BaTiO3 powders described by the nominal formula Ba1-xCexTi1-x/4O3 with x = 0.005 and 0.05 were synthesized by the acetate variant of the sol-gel method. The structural parameters, particle size, and morphology are strongly dependent on the Ce3+ content. From these powders, dense ceramics were prepared by conventional sintering at 1300 °C for 2 h, as well as by spark plasma sintering at 1050 °C for 2 min. For the conventionally sintered ceramics, the XRD data and the dielectric and hysteresis measurements reveal that at room temperature, the specimen with low cerium content (x = 0.005) was in the ferroelectric state, while the samples with significantly higher Ce3+ concentration (x = 0.05) were found to be in the proximity of the ferroelectric-paraelectric phase transition. The sample with low solute content after spark plasma sintering exhibited insulating behavior, with significantly higher values of relative permittivity and dielectric losses over the entire investigated temperature range relative to the conventionally sintered sample of similar composition. The spark-plasma-sintered Ce-BaTiO3 specimen with high solute content (x = 0.05) showed a fine-grained microstructure and an almost temperature-independent colossal dielectric constant which originated from very high interfacial polarization.
ABSTRACT
In the recent years, there is an extensive effort concentrated towards the development of nanoparticles with near-infrared emission within the so called second or third biological windows induced by excitation outside 800-1000 nm range corresponding to the traditional Nd (800 nm) and Yb (980 nm) sensitizers. Here, we present a first report on the near-infrared (900-1700 nm) emission of significant member of cubic sesquioxides, Er-Lu2O3 nanoparticles, measured under both near-infrared up-conversion and low energy X-ray excitations. The nanoparticle compositions are optimized by varying Er concentration and Li addition. It is found that, under ca. 1500 nm up-conversion excitation, the emission is almost monochromatic (>93%) and centered at 980 nm while over 80% of the X-ray induced emission is concentrated around 1500 nm. The mechanisms responsible for the up-conversion emission of Er - Lu2O3 are identified by help of the up-conversion emission and excitation spectra as well as emission decays considering multiple excitation/emission transitions across visible to near-infrared ranges. Comparison between the emission properties of Er-Lu2O3 and Er-Y2O3 induced by optical and X-ray excitation is also presented. Our results suggest that the further optimized Er-doped cubic sesquioxides represent promising candidates for bioimaging and photovoltaic applications.
ABSTRACT
The formation of separate phases in crystalline materials is promoted by doping with elements with different valences and ionic radii. Control of the formation of separate phases in multiferroics is extremely important for their magnetic, ferroelectric and elastic properties, which are relevant for multifunctional applications. The ordering of dopants and incipient phase separation were studied in lead titanate-based multiferroics with the formula (Pb0.88Nd0.08)(Ti0.98-xFexMn0.02)O3 (x = 0.00, 0.03, 0.04, 0.05) by means of a combination of Mössbauer spectroscopy, XPS, HRTEM, dielectric and anelastic spectroscopy. We found that Fe ions are substituted as Fe3+ at Ti sites and preferentially exhibit pentahedral coordination, whereas Ti ions have coexisting valences of Ti4+/Ti3+. Fe3+ ions are preferentially ordered in clusters, and there exists a transition temperature TC1, below which phase separation occurs between a tetragonal phase T1 free of magnetic clusters and a cubic phase, and a lower transition temperature TC2, below which the cubic phase rich in magnetic clusters is transformed into a tetragonal phase T2. The phase separation persists at the nanoscale level down to room temperature and is visible in HRTEM images as a mixing of nanodomains with different tetragonality ratios. This phase separation was observed over the whole studied concentration range of xFe values. It occurs progressively with the value of xFe, and the transition temperature TC2 decreases with the concentration from about 620 K (xFe = 0.03) to about 600 K (xFe = 0.05), while TC1 remains nearly constant.
ABSTRACT
Gold nanowire networks (AuNWNs) with average widths of 17.74 nm (AuNWN(1)) or 23.54 nm (AuNWN(2)) were synthesized by direct reduction of HAuCl(4) with sodium borohydride powder in deep eutectic solvents, such as ethaline or reline, at 40 °C. Their width and length were dependent on the type of solvent and the NaBH(4)/HAuCl(4) molar ratio (32 in ethaline and 5.2 in reline). High resolution transmission electron microscopy (HR-TEM) analysis of the gold nanowire networks showed clear lattice fringes of polycrystalline nanopowder of d = 2.36, 2.04, 1.44, and 1.23 Å corresponding to the (111), (200), (220), or (311) crystallographic planes of face centered cubic gold. The purified AuNWNs were used as catalysts for the chemical reduction of p-nitroaniline to diaminophenylene with sodium borohydride in aqueous solution. The reaction was monitored in real time by UV-vis spectroscopy. The results show that the reduction process is six times faster in the presence of gold nanowire networks stabilized by urea from the reline (AuNWN(2)) than in the presence of gold nanowire networks stabilized by ethylene glycol from ethaline (AuNWN(1)). This is due to a higher number of corners and edges on the gold nanowires synthesized in reline than on those synthesized in ethaline as proven by X-ray diffraction (XRD) patterns recorded for both types of gold nanowire networks. Nevertheless, both types of nanomaterials determined short times of reaction and high conversion of p-nitroaniline to diaminophenylene. These gold nanomaterials represent a new addition to a new generation of catalysts: gold based catalysts.
