ABSTRACT
Modified asphalt binders are still considered important in asphalt pavement. However, the comprehensive use of various modifiers is limited due to storage stability issues. Moreover, there is a scarcity of detailed analyses regarding the degree of separation for asphalt binders among each method despite the utilization of various methods to assess the storage stability of binders. Therefore, a comprehensive analysis was conducted to assess the storage stability of asphalt binder modified with a crumb rubber modifier (CRM) and styrene-isoprene-styrene (SIS), utilizing five evaluation factors following the ASTM D7173 guidelines based on four mixing methods (A: high-shear mixing method, B: low-speed agitating method, C: high-shear mixing method + low mixing method, D: low-speed agitating method + low mixing method). To produce the modified asphalt binder, the proportions of the CRM were 5% and 10% for each binder, and 10% SIS was added to all binders. The results in this study convey that (1) the addition of the modifier led to an increase in G*/sin δ with different mixing methods, but using mixing methods (C and D) for a relatively long time resulted in a lower G*/sin δ, indicating suboptimal performance; (2) through the multiple stress creep recovery (MSCR), rheological properties of Jnr and % rec exhibited trends similar to G*/sin δ evaluation, highlighting an improved elastic recovery with a higher modifier content; (3) storage stability assessment revealed consistent trends in high-shear mixing groups (A and C), while low-speed mixing groups (B and D) exhibited an elevated separation index (SI), suggesting a sensitivity to modification conditions; (4) evaluation using the MSCR method indicated that % rec with a 3.2 kPa load is effective for the sensitive assessment of binder storage stability and Jnr showed a limited sensitivity across varying loads, advocating for % rec for precise evaluation; and (5) despite permitting various tests, achieving consistent results remains challenging. Future research should explore diverse modifiers and optimal evaluation methods to enhance knowledge of binder behavior and separation dynamics.
ABSTRACT
This study aimed to evaluate the impact of a two-step modification process involving kaolinite and cloisite Na+ on the storage stability of rubberized binders. The process involved the manual combination of virgin binder PG 64-22 with crumb rubber modifier (CRM), which was heated to condition it. The preconditioned rubberized binder was then modified for two hours at a high speed of 8000 rpm using wet mixing. The second stage modification was performed in two parts, with part 1 using only crumb rubber as the modifier and part 2 involving the use of kaolinite and montmorillonite nano clays at a replacement percentage of 3% to the original weight of the binder along with the crumb rubber modifier. The Superpave and multiple shear creep recovery (MSCR) test methods were used to calculate the performance characteristics and separation index % of each modified binder. The results showed that the viscosity properties of kaolinite and montmorillonite improved the performance class of the binder, with montmorillonite demonstrating greater viscosity values than kaolinite even at high temperatures. Additionally, kaolinite with rubberized binders showed higher resistance to rutting, and the % recovery value from multiple shear creep recovery testing indicated that kaolinite with rubberized binders was more effective than montmorillonite with rubberized binders, even at higher load cycles. The use of kaolinite and montmorillonite reduced phase separation between the asphaltene phase and rubber-rich phase at higher temperatures, but the performance of the rubber binder was affected by higher temperatures. Overall, kaolinite with the rubber binder generally demonstrated greater binder performance.
ABSTRACT
Crumb rubber modifier (CRM) binders easily suffer from instability at high temperatures, with many suggestions being developed to evaluate their storage stability. However, much uncertainty around CRM binders still exists regarding the relationship between mixing methods and experiments in order to calculate the separation index. In this study, a laboratory investigation into how CRM binders behave regarding storage stability using different mixing methods and experiments was conducted. The CRM asphalt binder in this study was prepared through a wet mixing process with the addition of 5% and 10% crumb rubber modifier (by weight) at 200 °C. The three main modification methods were method A: high-shear mixing (8000 rpm) for 2 h, method B: low mixing (300 rpm) for 8 h, and method C: high-shear mixing (8000 rpm) for 2 h + low mixing (300 rpm) for 6 h. In addition, the effect of separation index (SI) on storage stability was assessed, measuring viscosity, G*/sin δ, and percentage recovery. In general, the results of this study revealed that method C appeared to have the most prominent effect on decreasing the difference between the values of the top and bottom parts; the results for 5% CRM using method C showed that there were no differences among the values for the top, middle, and bottom parts; from the MSCR test, method C was effective in decreasing the difference between the values of the top and bottom parts. It was observed that method C improved storage stability. However, the results for percentage recovery were relatively higher than the separation index when using rotational viscosity and G*/sin δ.
ABSTRACT
The study presents an experimental evaluation to improve the resistivity of binders with "Styrene-Butadiene-Styrene" (SBS) and "Processed oil" by studying the physical properties, rheology, and cracking. For this experiment, PG 64-22 was mixed with SBS at different percentages of 5%, 10%, and 15% by weight of the original binder with two processed oil contents of 6% and 12% by weight of the binder. Laboratory tests have been conducted at various high, medium, and low temperature ranges to evaluate their properties. The processed oil polymer modified asphalt (PMA) binder is artificially aged in both the short and long-term using a Rolling Thin Film Oven (RTFO) and a Pressure Aging Vessel (PAV). The Superpave testing method was performed on modified binders using a Rotational Viscometer (RV), Dynamic Shear Rheometer (DSR), and Bending Beam Rheometer (BBR). The results of this study illustrate (1) The addition of SBS leads to higher viscosity, but the co-modification of asphalt binder with the processed oil shows a significant modulation of the viscosity value. (2) In addition, processed oil reduced the resistance to rutting, but the addition of SBS significantly improved the rutting resistance of the asphalt binder. (3) The addition of SBS and processed oil improved the value of G sin δ, notably. (4) According to BBR, it has been shown that the addition of SBS in addition to the processed oil improves the stiffness values of modified asphalt binders.
