Significance of Zn Complex Concentration on Microstructure Evolution and Corrosion Behavior of Al/WS2.

Corrosion is a harmful processes which by definition is a chemical or electrochemical reaction between a substance (usually a metal) and the environment which leads to a change in the properties of the substance and has destructive effects. In this study, new composites consisting of Al/WS2/ZnTerp-2TH with 5 and 10 wt.% ZnTerp-2TH were prepared and the results were fully compared. Al/WS2 played the role of matrix and ZnTerp-2TH played the role of reinforcement. In other words, as a novelty to prevent the corrosion of Al/WS2, ZnTerp-2TH is designed and synthesized and showed good results when the corrosion ratio was reduced by the existence of ZnTerp-2TH. Furthermore, the NMR and mass analysis of ZnTerp-2TH were carried out, and the thermal properties, X-ray diffraction, Fourier-transform infrared (FTIR) spectroscopy, morphology, energy-dispersive X-ray spectroscopy (EDX) analysis and corrosion behavior of the composites were also discussed in detail. The crystal size values of composites were calculated by the modified Scherrer method 34, 26 and 27 nm for Al/WS2, Al/WS2/5 wt.% ZnTerp-2TH and Al/WS2/10 wt.% ZnTerp-2TH, respectively. The microstructural examination of the specimens showed that the reinforcing phase (ZnTerp-2TH) has a favorable distribution on the surface of Al/WS2 when it covers the cracks and holes. In addition, the corrosion investigation results showed that the addition of ZnTerp-2TH to Al/WS2 can improve the corrosion resistance when the Ecorr and Icorr values of Al/WS2/10 wt.% ZnTerp-2TH were recorded in tandem -724 mV/decade and 5 uA cm-2.

Experimental and Numerical Study of Healing Effect on Delamination Defect in Infusible Thermoplastic Composite Laminates.

The integrity of delaminated composite structures can be restored by introducing a thermally-based healing effect on continuous fiber-reinforced thermoplastic composites (CFRTPC). The phenomenon of thermoplastics retaining their properties after melting and consolidation has been applied by heating the delaminated composite plates above their glass transition temperature under pressure. In the current investigation, the composite is comprised of Methyl methacrylate (MMA)-based infusible lamination resin combined with benzoyl peroxide initiator, which polymerizes into a Polymethyl methacrylate (PMMA) matrix. For the reinforcement, unidirectional 220 gr/m2 glass filament fabric was used. Delamination damage is artificially induced during the fabrication of laminate plates. The distributed delamination region before and after thermally activated healing was determined by using non-destructive testing with active thermography. An experimental approach is employed to characterize the thermal healing effect on mechanical properties. Experimentally determined technological parameters for thermal healing have been successfully applied to repair delamination defects on composite plates. Based on the compression-after-impact (CAI) test methodology, the intact, damaged, and healed composite laminates were loaded cyclically to evaluate the healing effect on stiffness and strength. During the CAI test, the 3D digital image correlation (DIC) technique was used to measure the displacement and deformation fields. Experimental results reveal the difference between the behavior of healed and damaged specimens. Additionally, the numerical models of intact, damaged, and healed composite laminates were developed using the finite element code LS-Dyna. Numerical models with calibrated material properties and tie-break contact constants provide good correlation with experimental results and allow for the prediction of the mechanical behavior of intact, damaged, and healed laminated plates. The comparison analysis based on CAI test results and modal characteristics obtained by the 3D Laser Doppler Vibrometer (Polytec GmbH, Karlsbad, Germany) proved that thermal healing partially restores the mechanical properties of damaged laminate plates. In contrast, active thermography does not necessarily indicate a healing effect.

Nanocomposite Based on HA/PVTMS/Cl2FeH8O4 as a Gas and Temperature Sensor.

In this paper, a novel nanocrystalline composite material of hydroxyapatite (HA)/polyvinyltrimethoxysilane (PVTMS)/iron(II)chloride tetrahydrate (Cl2FeH8-O4) with hexagonal structure is proposed for the fabrication of a gas/temperature sensor. Taking into account the sensitivity of HA to high temperatures, to prevent the collapse and breakdown of bonds and the leakage of volatiles without damaging the composite structure, a freeze-drying machine is designed and fabricated. X-ray diffraction, FTIR, SEM, EDAX, TEM, absorption and photoluminescence analyses of composite are studied. XRD is used to confirm the material structure and the crystallite size of the composite is calculated by the Monshi-Scherrer method, and a value of 81.60 ± 0.06 nm is obtained. The influence of the oxygen environment on the absorption and photoluminescence measurements of the composite and the influence of vaporized ethanol, N2 and CO on the SiO2/composite/Ag sensor device are investigated. The sensor with a 30 nm-thick layer of composite shows the highest response to vaporized ethanol, N2 and ambient CO. Overall, the composite and sensor exhibit a good selectivity to oxygen, vaporized ethanol, N2 and CO environments.

Effects of 5 wt.% Polycaprolactone, Polyhydroxybutyrate and Polyvinyltrimethoxysilane on the Properties of Ag/Zn/Mg Alloy.

Mg-based alloys have several suitable properties for biomaterials, but they have major problems of being less antibacterial and have a low mechanical strength. To solve these problems, a new combination of Ag/Zn/Mg was prepared in this study, where the presence of Zn and Ag can help to increase the bioactivity. The use of 5 wt.% polymers consisting of PolyCaproLactone (PCL), PolyHydroxyButyrate (PHB) and PolyVinylTriMethoxySilane (PVTMS) is also investigated. DSC, XRD, TEM, FTIR, SEM, and EDAX analysis, as well as mechanical and bioactive behavior, were investigated to characterize the prepared composites. In the comparison, the best behavior was found when PHB was used. The results show that the strength values ranged from ~201 to 261 MPa.

Numerical and Experimental Analysis of Mechanical Properties of Natural-Fiber-Reinforced Hybrid Polymer Composites and the Effect on Matrix Material.

The impact of matrix material on the mechanical properties of natural-fiber-reinforced hybrid composites was studied by comparing their experimental, and numerical analysis results. In the present work hemp and flax fibers were used as reinforcement and epoxy resin and ecopoxy resin along with hardener were used as matrix materials. To study the influence of the matrix material, two sets of hybrid composites were fabricated by varying the matrix material. The composite samples were fabricated by using the compression-molding technique followed by a hand layup process. A total of five different composites were fabricated by varying the weight fraction of fiber material in each set based on the rule of the hybridization process. After fabrication, the mechanical properties of the composite samples were tested and morphological studies were analyzed by using SEM-EDX analysis. The flexural-test fractured specimens were analyzed by using a scanning electron microscope (SEM). In addition, theoretical analysis of the elastic properties of hybrid composites was carried out by using the Halpin-Tsai approach. The results showed that the hybrid composites had superior properties to individual fiber composites. Overall, epoxy resin matrix composites exhibited superior properties to ecopoxy matrix composites.

New Approach for Preparing In Vitro Bioactive Scaffold Consisted of Ag-Doped Hydroxyapatite + Polyvinyltrimethoxysilane.

Recently, researchers have focused on the biocompatibility and mechanical properties of highly porous structures of biomaterials products. Porous composites are a new category of bioengineering that possess excellent functional and structural properties. In this study, the physical and mechanical properties of prepared doped silver (Ag)-hydroxyapatite (HA) by the mechanochemical and spark plasma sintering (SPS) methods were investigated. The influence of dopant on phase formation, structural properties, mechanical properties and morphological characteristics was investigated. Furthermore, in this case, as a new approach to produce a porous scaffold with an average size of >100 µm, the hair band was used as a mold. According to the Monshi-Scherrer method, the crystal size of scaffold was calculated 38 ± 2 nm and this value was in the good agreement with average value from transmission electron microscopy (TEM) analysis. In addition, the stress-strain compression test of scaffold was considered, and the maximum value of compressive strength was recorded ~15.71 MPa. Taking into account the XRD, TEM, Fourier-transform infrared (FTIR), scanning electron microscope (SEM) and energy dispersive X-Ray analysis (EDAX) analysis, the prepared scaffold was bioactive and the effects of doped Ag-HA and the use of polyvinyltrimethoxysilane (PVTMS) as an additive were desirable. The results showed that the effect of thermal treatment on composed of Ag and HA were impressive while no change in transformation was observed at 850 °C. In addition, PVTMS plays an important role as an additive for preventing the decomposition and creating open-microporous in the scaffold that these porosities can be helpful for increasing bioactivity.

X-ray Diffraction Analysis and Williamson-Hall Method in USDM Model for Estimating More Accurate Values of Stress-Strain of Unit Cell and Super Cells (2 × 2 × 2) of Hydroxyapatite, Confirmed by Ultrasonic Pulse-Echo Test.

Taking into account X-ray diffraction, one of the well-known methods for calculating the stress-strain of crystals is Williamson-Hall (W-H). The W-H method has three models, namely (1) Uniform deformation model (UDM); (2) Uniform stress deformation model (USDM); and (3) Uniform deformation energy density model (UDEDM). The USDM and UDEDM models are directly related to the modulus of elasticity (E). Young's modulus is a key parameter in engineering design and materials development. Young's modulus is considered in USDM and UDEDM models, but in all previous studies, researchers used the average values of Young's modulus or they calculated Young's modulus only for a sharp peak of an XRD pattern or they extracted Young's modulus from the literature. Therefore, these values are not representative of all peaks derived from X-ray diffraction; as a result, these values are not estimated with high accuracy. Nevertheless, in the current study, the W-H method is used considering the all diffracted planes of the unit cell and super cells (2 × 2 × 2) of Hydroxyapatite (HA), and a new method with the high accuracy of the W-H method in the USDM model is presented to calculate stress (σ) and strain (ε). The accounting for the planar density of atoms is the novelty of this work. Furthermore, the ultrasonic pulse-echo test is performed for the validation of the novelty assumptions.

Development and Analysis of Mechanical Properties of Caryota and Sisal Natural Fibers Reinforced Epoxy Hybrid Composites.

In recent years, natural fiber reinforced polymer composites have gained much attention over synthetic fiber composites because of their many advantages such as low-cost, light in weight, non-toxic, non-abrasive, and bio-degradable properties. Many researchers have found interest in using epoxy resin for composite fabrication over other thermosetting and thermoplastic polymers due to its dimensional stability and mechanical properties. In this research work, the mechanical and moisture properties of Caryota and sisal fiber-reinforced epoxy resin hybrid composites were investigated. The main objective of these studies is to develop hybrid composites and exploit their importance over single fiber composites. The Caryota and sisal fiber reinforced epoxy resin composites were fabricated by using the hand lay-up technique. A total of five different samples (40C/0S, 25C/15S, 20C/20S, 15C/25S, 0C/40S) were developed based on the rule of hybridization. The samples were allowed for testing to evaluate their mechanical, moisture properties and the morphology was studied by using the scanning electron microscope analysis. It was observed that hybrid composites have shown improved mechanical properties over the single fiber (Individual fiber) composites. The moisture studies stated that all the composites were responded to the water absorption but single fiber composites absorbed more moisture than hybrid composites.

Relationship between Young's Modulus and Planar Density of Unit Cell, Super Cells (2 × 2 × 2), Symmetry Cells of Perovskite (CaTiO3) Lattice.

Calcium titanate-CaTiO3 (perovskite) has been used in various industrial applications due to its dopant/doping mechanisms. Manipulation of defective grain boundaries in the structure of perovskite is essential to maximize mechanical properties and stability; therefore, the structure of perovskite has attracted attention, because without fully understanding the perovskite structure and diffracted planes, dopant/doping mechanisms cannot be understood. In this study, the areas and locations of atoms and diffracted planes were designed and investigated. In this research, the relationship between Young's modulus and planar density of unit cell, super cells (2 × 2 × 2) and symmetry cells of nano CaTiO3 is investigated. Elastic constant, elastic compliance and Young's modulus value were recorded with the ultrasonic pulse-echo technique. The results were C11 = 330.89 GPa, C12 = 93.03 GPa, C44 = 94.91 GPa and E = 153.87 GPa respectively. Young's modulus values of CaTiO3 extracted by planar density were calculated 162.62 GPa, 151.71 GPa and 152.21 GPa for unit cell, super cells (2 × 2 × 2) and symmetry cells, respectively. Young's modulus value extracted by planar density of symmetry cells was in good agreement with Young's modulus value measured via ultrasonic pulse-echo.

Analysis of Mechanical and Wettability Properties of Natural Fiber-Reinforced Epoxy Hybrid Composites.

Natural fibers have many advantages over synthetic fibers due to their lightness, low cost, biodegradability, and abundance in nature. The demand for natural fiber hybrid composites in various applications has increased recently, because of its promising mechanical properties. In this research work, the mechanical and wettability properties of reinforced natural fiber epoxy resin hybrid composites were investigated. The main aim of this research work is the fabrication of hybrid composites and exploit its importance over individual fiber composites. The composites were fabricated based on the rule of hybridization mixture (0.4 wf) of two fibers using sets of either hemp and flax or banana and pineapple, each set with 40 wt%, as well as four single fiber composites, 40 wt% each, as reinforcement and epoxy resin as matrix material. A total of two sets (hemp/flax and banana/pineapple) of hybrid composites were fabricated by using a hand layup technique. One set as 40H/0F, 25H/15F, 20H/20F, 15H/25F, 0H/40F, and the second one as 40B/0P, 25B/15P, 20B/20P, 15B/25P, 0B/40P weight fraction ratios. The fabricated composites were allowed for testing to examine its mechanical, wettability, and moisture properties. It has been observed that, in both cases, hybrid composites showed improved mechanical properties when compared to the individual fiber composites. The wettability test was carried out by using the contact angle measurement technique. All composites in both cases, hybrid or single showed contact angle less than 90°, which is associated with the composite hydrophilic surface properties. The moisture analysis stated that all the composites responded for moisture absorption up to 96 h and then remained constant in both cases. Hybrid composites absorbed less moisture than individual fiber composites.

Measurement Modulus of Elasticity Related to the Atomic Density of Planes in Unit Cell of Crystal Lattices.

Young's modulus (E) is one of the most important parameters in the mechanical properties of solid materials. Young's modulus is proportional to the stress and strain values. There are several experimental and theoretical methods for gaining Young's modulus values, such as stress-strain curves in compression and tensile tests, electromagnetic-acoustic resonance, ultrasonic pulse echo and density functional theory (DFT) in different basis sets. Apparently, preparing specimens for measuring Young's modulus through the experimental methods is not convenient and it is time-consuming. In addition, for calculating Young's modulus values by software, presumptions of data and structures are needed. Therefore, this new method for gaining the Young's modulus values of crystalline materials is presented. Herein, the new method for calculating Young's modulus of crystalline materials is extracted by X-ray diffraction. In this study, Young's modulus values were gained through the arbitrary planes such as random (hkl) in the research. In this study, calculation of Young's modulus through the relationship between elastic compliances, geometry of the crystal lattice and the planar density of each plane is obtained by X-ray diffraction. Sodium chloride (NaCl) with crystal lattices of FCC was selected as the example. The X-ray diffraction, elastic stiffness constant and elastic compliances values have been chosen by the X'Pert software, literature and experimental measurements, respectively. The elastic stiffness constant and Young's modulus of NaCl were measured by the ultrasonic technique and, finally, the results were in good agreement with the new method of this study. The aim of the modified Williamson-Hall (W-H) method in the uniform stress deformation model (USDM) utilized in this paper is to provide a new approach of using the W-H equation, so that a least squares technique can be applied to minimize the sources of errors.

Review of Hybrid Fiber Based Composites with Nano Particles-Material Properties and Applications.

The present review article provides an overview of the properties of various natural and synthetic fibers for the fabrication of pure natural composites and the combination of both natural/synthetic fibers-based hybrid composites, bio-based resins, various fabrication techniques, chemical and mechanical properties of fibers, the effect of chemical treatment and the influence of nanoparticles on the composite materials. Natural fibers are becoming more popular and attractive to researchers, with satisfactory results, due to their availability, ease of fabrication, cost-effectiveness, biodegradable nature and being environmentally friendly. Hybrid composites made up of two different natural fibers under the same matrix material are more popular than a combination of natural and synthetic fibers. Recent studies relevant to natural fiber hybrid composites have stated that, due to their biodegradability and the strength of individual fibers causing an impact on mechanical properties, flame retardancy and moisture absorption, natural fibers need an additional treatment like chemical treatment for the fibers to overcome those drawbacks and to enhance their better properties. The result of chemical treatment on composite material properties such as thermal, mechanical and moisture properties was studied. Researchers found that the positive influence on overall strength by placing the filler materials (nanoparticles) in the composite materials. Hybrid composites are one of the fields in polymer science that are attracting consideration for various lightweight applications in a wide range of industries such as automobile, construction, shipping, aviation, sports equipment, electronics, hardware and biomedical sectors.

Comparing Methods for Calculating Nano Crystal Size of Natural Hydroxyapatite Using X-Ray Diffraction.

We report on a comparison of methods based on XRD patterns for calculating crystal size. In this case, XRD peaks were extracted from hydroxyapatite obtained from cow, pig, and chicken bones. Hydroxyapatite was synthesized through the thermal treatment of natural bones at 950 °C. XRD patterns were selected by adjustment of X-Pert software for each method and for calculating the size of the crystals. Methods consisted of Scherrer (three models), Monshi-Scherrer, three models of Williamson-Hall (namely the Uniform Deformation Model (UDM), the Uniform Stress Deformation Model (USDM), and the Uniform Deformation Energy Density Model (UDEDM)), Halder-Wanger (H-W), and the Size Strain Plot Method (SSP). These methods have been used and compared together. The sizes of crystallites obtained by the XRD patterns in each method for hydroxyapatite from cow, pig, and chicken were 1371, 457, and 196 nm in the Scherrer method when considering all of the available peaks together (straight line model). A new model (straight line passing the origin) gave 60, 60, and 53 nm, which shows much improvement. The average model gave 56, 58, and 52 nm, for each of the three approaches, respectively, for cow, pig, and chicken. The Monshi-Scherrer method gave 60, 60, and 57 nm. Values of 56, 62, and 65 nm were given by the UDM method. The values calculated by the USDM method were 60, 62, and 62 nm. The values of 62, 62, and 65 nm were given by the UDEDM method for cow, pig, and chicken, respectively. Furthermore, the crystal size value was 4 nm for all samples in the H-W method. Values were also calculated as 43, 62, and 57 nm in the SSP method for cow, pig, and chicken tandemly. According to the comparison of values in each method, the Scherrer method (straight line model) for considering all peaks led to unreasonable values. Nevertheless, other values were in the acceptable range, similar to the reported values in the literature. Experimental analyses, such as specific surface area by gas adsorption (Brunauer-Emmett-Teller (BET)) and Transmission Electron Microscopy (TEM), were utilized. In the final comparison, parameters of accuracy, ease of calculations, having a check point for the researcher, and difference between the obtained values and experimental analysis by BET and TEM were considered. The Monshi-Scherrer method provided ease of calculation and a decrease in errors by applying least squares to the linear plot. There is a check point for this line that the slope must not be far from one. Then, the intercept gives the most accurate crystal size. In this study, the setup of values for BET (56, 52, and 49 nm) was also similar to the Monshi-Scherrer method and the use of it in research studies of nanotechnology is advised.

Development of Nanoporous AAO Membrane for Nano Filtration Using the Acoustophoresis Method.

A concept of a nanoporous anodic aluminum oxide (AAO) membrane as a vibro-active micro/nano-filter in a micro hydro mechanical system for the filtration, separation, and manipulation of bioparticles is reported in this paper. For the fabrication of a nanoporous AAO, a two-step mild anodization (MA) and hard anodization (HA) technique was used. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were used to analyze the surface morphology of nanoporous AAO. A nanoporous structure with a pore diameter in the range of 50-90 nm, an interpore distance of 110 nm, and an oxide layer thickness of 0.12 mm with 60.72% porosity was obtained. Fourier-transform infrared spectroscopy (FTIR) and energy-dispersive X-ray spectroscopy (EDS) were employed to evaluate AAO chemical properties. The obtained results showed that the AAO structure is of hexagonal symmetry and showed where Al2O3 is dominant. The hydrophobic properties of the nanoporous surface were characterized by water contact angle measurement. It was observed that the surface of the nanoporous AAO membrane is hydrophilic. Furthermore, to determine whether a nanomembrane could function as a vibro-active nano filter, a numerical simulation was performed using COMSOL Multiphysics 5.4 (COMSOL Inc, Stockholm, Sweden). Here, a membrane was excited at a frequency range of 0-100 kHz for surface acoustics wave (SAW) distribution on the surface of the nanoporous AAO using a PZT 5H cylinder (Piezo Hannas, Wuhan, China). The SAW, standing acoustic waves, and travelling acoustic waves of different wavelengths were excited to the fabricated AAO membrane and the results were compared with experimental ones, obtained from non-destructive testing method 3D scanning vibrometer (PSV-500-3D-HV, Polytec GmbH, Waldbronn, Germany) and holographic interferometry system (PRISM, Hy-Tech Forming Systems (USA), Phoenix, AZ, USA). Finally, a simulation of a single nanotube was performed to analyze the acoustic pressure distribution and time, needed to center nanoparticles in the nanotube.

Design of Controllable Novel Piezoelectric Components for Microfluidic Applications.

This paper reviews recent investigations and achievements in the design of controllable functional components for improving microfluidic systems, its effectiveness, and functionality. The main purpose was to design novel microstructures with piezoelectric properties (microresonators), which enable one to control the effectiveness of fluid flow in micro-hydro-mechanical devices for biomedical/biochemical purposes. Controllable properties were obtained by incorporating different types of binders in a piezoelectric ceramic matrix (lead zirconate titanate): polyvinyl butyral (PVB), poly methyl methacrylate (PMMA), and polystyrene (PS). The change in chemical composition of PZT helps to manipulate the piezoelectric characteristics, surface morphology, mechanical properties, etc., of the designed microfluidic element with the microstructure in it.

Comparison of diffraction patterns exposed by pulsed and CW lasers on positive-tone photoresist.

Two different grating formation geometries for recording onto the positive-tone photoresist with pulsed laser and continuous-wave sources are analyzed and compared. Diffraction efficiency measurements and atomic force microscopy (AFM) examination have been performed in order to investigate the optical and topographical properties of the recorded structures. Gratings patterned by a continuous-wave laser and by a pulsed laser working in the single pulse and multipulse regimes showed different surface roughness and optical properties. The possible reasons for surface roughness and effective exposure differences between gratings created with pulsed and continuous-wave laser radiations are discussed. The processing schemes for diffractive structures patterned by pulsed laser onto positive-tone photoresist for commercial hologram production are analyzed and presented in this work.

Influence of PZT Coating Thickness and Electrical Pole Alignment on Microresonator Properties.

With increasing technical requirements in the design of microresonators, the development of new techniques for lightweight, simple, and inexpensive components becomes relevant. Lead zirconate titanate (PZT) is a powerful tool in the formation of these components, allowing a self-actuation or self-sensing capability. Different fabrication methods lead to the variation of the properties of the device itself. This research paper covers the fabrication of a novel PZT film and the investigations of its chemical, surface, and dynamic properties when film thickness is varied. A screen-printing technique was used for the formation of smooth films of 60 µm, 68 µm, and 25 µm thickness. A custom-made poling technique was applied to enhance the piezoelectric properties of the designed films. However, poling did not change any compositional or surface characteristics of the films; changes were only seen in the electrical ones. The results showed that a thinner poled PZT film having a chemical composition with the highest amount of copper and zirconium led to better electrical characteristics (generated voltage of 3.5 mV).

Periodical Microstructures Based on Novel Piezoelectric Material for Biomedical Applications.

A novel cantilever type piezoelectric sensing element was developed. Cost-effective and simple fabrication design allows the use of this element for various applications in the areas of biomedicine, pharmacy, environmental analysis and biosensing. This paper proposes a novel piezoelectric composite material whose basic element is PZT and a sensing platform where this material was integrated. Results showed that a designed novel cantilever-type element is able to generate a voltage of up to 80 µV at 50 Hz frequency. To use this element for sensing purposes, a four micron periodical microstructure was imprinted. Silver nanoparticles were precipitated on the grating to increase the sensitivity of the designed element, i.e., Surface Plasmon Resonance (SPR) effect appears in the element. To tackle some issues (a lack of sensitivity, signal delays) the element must have certain electronic and optical properties. One possible solution, proposed in this paper, is a combination of piezoelectricity and SPR in a single element.

Biomechanical aspects of locking reconstruction plate positioning in osteosynthesis of transverse clavicle fracture.

UNLABELLED: The aim of this study was to evaluate and compare the biomechanical effects of locking reconstruction plate positioning on the osteosynthesis of clavicle midshaft simulated transverse fractures. MATERIAL AND METHODS: Twelve synthetic clavicles with simulated midshaft transverse fractures were repaired with a 3.5-mm locking reconstruction plate in the anteroinferior or the superior position. The clavicles were randomly assigned to 2 groups (6 per group). Each repaired clavicle was tested in cantilever bending by using the universal testing machine. The maximal load and the displacement of the specimens at a load of 40 N were recorded for each group. RESULTS: The anteroinferior plating osteosynthesis with a 3.5-mm locking reconstruction plate could bear an average maximal load of 183.3 N (SD, 11.3); the corresponding load for the superior plating osteosynthesis with the identical implants was 444.8 N (SD, 102.3), and the mean displacement was 1.5 mm (SD, 0.5) and 0.7 mm (SD, 0.2), respectively. CONCLUSIONS: The superior plating osteosynthesis of simulated midshaft transverse clavicle fractures with the 7-hole 3.5-mm locking reconstruction plate had a significantly higher bending (from top to bottom) load to failure in comparison with the anteroinferior plating osteosynthesis of the clavicle with the identical implants. Clavicles plated with the 7-hole 3.5-mm locking reconstruction plate at the superior aspect exhibited a significantly greater biomechanical stability at a load of 40 N than those plated at the anteroinferior aspect.