Metallic and Ceramic Materials Integrity-Surface Engineering for Wear, Corrosion and Erosion Prevention.

The literature systematically describes the wear behavior and phenomena responsible for the degradation resistance of materials [...].

Shot Peening Effect on Sliding Wear in 0.9% NaCl of Additively Manufactured 17-4PH Steel.

The growing demand for modern steels showing corrosion and tribological resistance has led to their increased use in the production of medical devices. This study analyzed the effect of shot peening on wear resistance in 0.9% NaCl solution of 17-4PH steel produced by direct laser metal sintering (DMLS) technology. The study's novelty relies on revealing the effect of shot peening (SP) surface treatment on the wet sliding wear resistance of 17-4PH steel produced with DMLS. Moreover, in the context of 17-4PH steel application for medical devices, the 0.9% NaCl tribological environment were selected, and SP processes were conducted using steel CrNi shot and ceramic (ZrO2) beads. The up-to-date scientific literature has not identified these gaps in the research. DMLS technology makes it possible to obtain products with complex architectures, but it also faces various challenges, including imperfections in the surface layer of products due to the use of 3D printing technology itself. The chemical and phase composition of the materials obtained, Vickers hardness, surface roughness, and microscopic and SEM imaging were investigated. Tribological tests were carried out using the ball-on-disc method, and the surfaces that showed traces of abrasion to identify wear mechanisms were subjected to SEM analysis. The XRD phase analysis indicates that austenite and martensite were found in the post-production state, while a higher martensitic phase content was found in peened samples due to phase transformations. The surface hardness of the peened samples increased by more than double, and the post-treatment roughness increased by 12.8% after peening CrNi steels and decreased by 7.8% after peening ZrO2 relative to the reference surfaces. Roughness has an identifiable effect on sliding wear resistance. Higher roughness promotes material loss. After the SP process, the coefficient of friction increased by 15.5% and 20.7%, while the wear factor (K) decreased by 25.9% and 32.7% for the samples peened with CrNi steels and ZrO2, respectively. Abrasive and adhesive mechanisms were dominant, featured with slight fatigue. The investigation showed a positive effect of SP on the tribological properties of DMSL 17-4PH.

Effects of Shot Peening and Electropolishing Treatment on the Properties of Additively and Conventionally Manufactured Ti6Al4V Alloy: A Review.

This literature review indicates that the basic microstructure of Ti6Al4V is bimodal, consisting of two phases, namely α + ß, and it occurs after fabrication using conventional methods such as casting, plastic forming or machining processes. The fabrication of components via an additive manufacturing process significantly changes the microstructure and properties of Ti6Al4V. Due to the rapid heat exchange during heat treatment, the bimodal microstructure transforms into a lamellar microstructure, which consists of two phases: α' + ß. Despite the application of optimum printing parameters, 3D printed products exhibit typical surface defects and discontinuities, and in turn, surface finishing using shot peening is recommended. A literature review signalizes that shot peening and electropolishing processes positively impact the corrosion behavior, the mechanical properties and the condition of the surface layer of conventionally manufactured titanium alloy. On the other hand, there is a lack of studies combining shot peening and electropolishing in one hybrid process for additively manufactured titanium alloys, which could synthesize the benefits of both processes. Therefore, this review paper clarifies the effects of shot peening and electropolishing treatment on the properties of both additively and conventionally manufactured Ti6Al4V alloys and shows the effect process on the microstructure and properties of Ti6Al4V titanium alloy.

Material's Strength Analysis of the Coupling Node of Axle of the Truck Trailer.

Road transport plays an important role in the transport of goods and people and is important for the national economy. Damage usually excludes the means of transport from operation, which causes disruption of supply chains. One such damage is the failure of the suspension system of the vehicle or trailer, which usually occurs when the vehicle is heavily loaded. Such a defective system has been analyzed in this publication. Mathematical apparatus and finite element method (FEM) numerical simulations were used. A dangerous axle cross-section in terms of load was indicated and the maximum stresses in this area were calculated for two types of roads. On highways, the stress at the critical point was 199 MPa, and on uneven roads it increased to 304 MPa, which is comparable to the yield point. It was found that the second form of vibration may cause stresses in the damage area, but the excitation frequency would have to be quite high. The probability of such a load and failure event occurring is low under operating conditions.

Effect of AISI H13 Steel Substrate Nitriding on AlCrN, ZrN, TiSiN, and TiCrN Multilayer PVD Coatings Wear and Friction Behaviors at a Different Temperature Level.

Moving components of industrial machines and tools are subjected to wear and friction. This reduces their useful life and efficiency in running conditions, particularly at high temperatures. One of the most popular solutions is to apply an appropriate surface coating to the tribocouple's base materials. In this study, tribometer experiments were used to evaluate the tribological performance of cathodic arc physical vapor deposited (CAPVD) AlCrN, TiSiN, CrTiN, and ZrN coatings on the gas nitrided AISI H13 tool steel to explore the effects of nitriding the steel on wear and friction behavior of these coatings at ambient and elevated temperatures. The coatings characterization is split into three main parts: mechanical, morphological, and chemical characterization. Nanoindentation has been used for mechanical characterization, thin film X-ray diffraction (XRD), and an energy-dispersive X-ray spectrometer mounted on a scanning electron microscope for chemical characterization, optical profilometer, and atomic force microscopy (AFM) for morphological characterization. Significant improvements in the adhesion qualities of the coatings to the substrate were achieved as a result of nitration. Due to this circumstance, the coatings' load-bearing capacity and high-temperature wear resistance ratings were enhanced. The wear results showed that the AISI H13 tool steel nitriding with AlCrN and ZrN layers decreased wear rates by two to three times at 700 °C.

Assessment of Corrosion Resistance and Hardness of Shot Peened X5CrNi18-10 Steel.

Although the application of shot peening facilitates increasing hardness and corrosion resistance of stainless steel, the inappropriate peening parameters result in overestimated hardening and exaggerated surface roughness, which deteriorate the surface morphology and negatively affect the corrosive behavior of treated steel. Therefore it is crucial to select the peening parameters that allow obtaining both high hardness and elevated corrosion resistance. This study aims to determine the effect of X5CrNi18-10 stainless steel samples shot peening on the surface morphology, hardness, and corrosion resistance. Samples were shot peened with a CrNi steel shot, applying 0.3 MPa and 0.4 MPa peening pressures and treatment times of 60 s and 120 s. Roughness analysis and microscopic and SEM-EDS examination were employed to state the effect of peening parameters on the sample's corrosive behavior in a 3.5% NaCl solution. The most promising shot peening parameters for Vickers hardness and electrochemical corrosion resistance were selected. It is revealed that the surface roughness increase has a detrimental effect on the corrosion behavior. Overall, high corrosion resistance and the high hardness of stainless steel samples were noted for the peening pressure of 0.4 MPa and time treatment of 60 s.

Effects of Shot Peening and Cavitation Peening on Properties of Surface Layer of Metallic Materials-A Short Review.

Shot peening is a dynamically developing surface treatment used to improve the surface properties modified by tool, impact, microblasting, or shot action. This paper reviews the basic information regarding shot peening methods. The peening processes and effects of the shot peening and cavitation peening treatments on the surface layer properties of metallic components are analysed. Moreover, the effects of peening on the operational performance of metallic materials are summarized. Shot peening is generally applied to reduce the surface roughness, increase the hardness, and densify the surface layer microstructure, which leads to work hardening effects. In addition, the residual compressive stresses introduced into the material have a beneficial effect on the performance of the surface layer. Therefore, peening can be beneficial for metallic structures prone to fatigue, corrosion, and wear. Recently, cavitation peening has been increasingly developed. This review paper suggests that most research on cavitation peening omits the treatment of additively manufactured metallic materials. Furthermore, no published studies combine shot peening and cavitation peening in one hybrid process, which could synthesize the benefits of both peening processes. Moreover, there is a need to investigate the effects of peening, especially cavitation peening and hybrid peening, on the anti-wear and corrosion performance of additively manufactured metallic materials. Therefore, the literature gap leading to the scope of future work is also included.

Effect of Microstructure and Hardness on Cavitation Erosion and Dry Sliding Wear of HVOF Deposited CoNiCrAlY, NiCoCrAlY and NiCrMoNbTa Coatings.

Metallic coatings based on cobalt and nickel are promising for elongating the life span of machine components operated in harsh environments. However, reports regarding the ambient temperature tribological performance and cavitation erosion resistance of popular MCrAlY (where M = Co, Ni or Co/Ni) and NiCrMoNbTa coatings are scant. This study comparatively investigates the effects of microstructure and hardness of HVOF deposited CoNiCrAlY, NiCoCrAlY and NiCrMoNbTa coatings on tribological and cavitation erosion performance. The cavitation erosion test was conducted using the vibratory method following the ASTM G32 standard. The tribological examination was done using a ball-on-disc tribometer. Analysis of the chemical composition, microstructure, phase composition and hardness reveal the dry sliding wear and cavitation erosion mechanisms. Coatings present increasing resistance to both sliding wear and cavitation erosion in the following order: NiCoCrAlY < CoNiCrAlY < NiCrMoNbTa. The tribological behaviour of coatings relies on abrasive grooving and oxidation of the wear products. In the case of NiCrMoNbTa coatings, abrasion is followed by the severe adhesive smearing of oxidised wear products which end in the lowest coefficient of friction and wear rate. Cavitation erosion is initiated at microstructure discontinuities and ends with severe surface pitting. CoNiCrAlY and NiCoCrAlY coatings present semi brittle behavior, whereas NiCrMoNbTa presents ductile mode and lesser surface pitting, which improves its anti-cavitation performance. The differences in microstructure of investigated coatings affect the wear and cavitation erosion performance more than the hardness itself.

Changes of cytotoxicity of Ti-6Al-4V alloy made by DMLS technology as effect of the shot peening.

OBJECTIVE: The aim the study was to investigate the impact of the shot peening process on the condition of the surface layer and biological properties of titanium alloy produced by means of the Direct Metal Laser Sintering (DMLS) method. MATERIAL AND METHODS: Specimens were prepared by the EOSINT M280 metal sintering laser system. The surfaces were subjected to the shot peening process using three different media, i.e. steel shot, nutshell granules and ceramic beads, after which they were subjected to profilometric analysis, scanning electron microscopic (SEM) observations and energy dispersive X-ray spectroscopy (EDS) tests, as well as to assessment of biological compatibility in terms of cytotoxicity (SH-SY5Y cell lines). RESULTS: The general results obtained from the tests indicate satisfactory biocompatibility of the examined surfaces and that the impact of the shot peening process on the titanium alloy cytotoxicity is acceptable. CONCLUSIONS: The lowest cytotoxicity was demonstrated by the surfaces modified by ceramic beads than the nutshells and the biggest steel shot correspondingly. Moreover, the shot peening process carried out by means of CrNi steel and ceramic shot caused the reduction of surface roughness when, for the surface processing by means of nutshell granules, the increase of surface roughness was observed compared with the unmodified surface of titanium alloy samples.

Tribological Behavior of AlCrSiN-Coated Tool Steel K340 Versus Popular Tool Steel Grades.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the differences in quantitative wear behavior and wear mechanisms between AlCrSiN-coated and bare steel K340 and five reference tool steels: X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with an AlCrSiN hard film (K340/AlCrSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/AlCrSiN were examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction were estimated and analyzed with respect to hardness and alloying composition of the materials under study. Scanning electron microscopy (SEM) observations were made to identify the sliding wear mechanisms of the analyzed tool steels and physical vapor deposition (PVD)- coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K340 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K340/AlCrSiN sample has a coefficient of friction (COF) of 0.529 and a wear factor of K = 5.68 × 10-7 m3 N-1 m-1, while the COF of the reference tool steels ranges from 0.70 to 0.89 and their wear factor ranges from 1.68 × 10-5 to 3.67 × 10-5 m3 N-1 m-1. The AlCrSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

Hardness and Wear Resistance of Dental Biomedical Nanomaterials in a Humid Environment with Non-Stationary Temperatures.

This study discusses a quantitative fatigue evaluation of polymer-ceramic composites for dental restorations, i.e., commercial material (Filtek Z550) and experimental materials Ex-nano (G), Ex-flow (G). Their evaluation is based on the following descriptors: microhardness, scratch resistance, and sliding wear. In order to reflect factors of environmental degradation conditions, thermal fatigue was simulated with a special computer-controlled device performing algorithms of thermocycling. Specimens intended for the surface strength and wear tests underwent 104 hydrothermal fatigue cycles. Thermocycling was preceded by aging, which meant immersing the specimens in artificial saliva at 37 °C for 30 days. Microhardness tests were performed with the Vickers hardness test method. The scratch test was done with a Rockwell diamond cone indenter. Sliding ball-on-disc friction tests were performed against an alumina ball in the presence of artificial saliva. A direct positive correlation was found between thermocycling fatigue and microhardness. The dominant mechanism of the wear of the experimental composites after thermocycling is the removal of fragments of the materials in the form of flakes from the friction surface (spalling). Hydrothermal fatigue is synergistic with mechanical fatigue.

Effect of Shot Peening on the Mechanical Properties and Cytotoxicity Behaviour of Titanium Implants Produced by 3D Printing Technology.

Structural discontinuities characterize the implants produced directly from metal powders in 3D printing technology. Mainly, the surface defects should be subjected to procedures associated with surface layer modification (likewise shot peening) resulting in the increase of the implant service life maintaining optimal biocompatibility. Therefore, the purpose of the present study was to investigate the effect of type of shot used for the peening process on the Ti-6Al-4V implants functional properties as well as the biological properties. The components were produced by DMLS (direct metal laser sintering) additive technology. The surfaces of titanium specimens have been subjected to the shot peening process by means of three different shots, i.e., CrNi steel shot, crushed nut shells, and ceramic balls shot. Then, the specimens have been subjected to profilometric analysis, microhardness tests, and static strength testing as well as to the assessment of biocompatibility in respect of cytotoxicity using human BJ fibroblasts. The shot peening process causes the strengthening of surface layer and the increase of strength parameters. Furthermore, the test results indicate good biocompatibility of surfaces being tested, and the effect of shot peening process on the titanium alloy cytotoxicity is acceptable. At the same time, most favourable behaviour in respect of cytotoxicity has been found in the case of surfaces modified by means of ceramic balls > nut shells > CrNi steel shot correspondingly.

Influence of photopolymerization parameters on the mechanical properties of polymer-ceramic composites applied in the conservative dentistry.

In this paper, the results of study of mechanical properties for four commercial polymer-ceramic composites applied in the conservative dentistry are presented, including one new silorane based composite and three standard composites based on methacrylate compounds. Influence of the type of light of diode and halogen polymerization lamps on the microhardness, flexural strength and elasticity were studied. Both exposed and unexposed specimens were taken into account. An exposure time was also differentiated (40 sec and 60 sec). Basic statistics of the analysed material parameters were determined. A post hoc test (Newman-Keuls) was performed in order to evaluate differences between microhardness of the materials studied, as well as Kruskal-Wallis test to evaluate differences in flexural strength and elasticity modulus of the material. It has been indicated that there is an impact of the type of lamp on the microhardness and flexural strength of composites with methacrylate matrix and lack of such impact in the case of composites containing siloranes. Additionally, it has been found that an increase of photopolymerization time has a significantly different impact on the mechanical properties depending on the type of irradiated material.

The influence of SiO2 and SiO2-TiO2 intermediate coatings on bond strength of titanium and Ti6Al4V alloy to dental porcelain.

OBJECTIVES: The purpose of this study was to evaluate the bond strength of commercially pure CPTi and Ti6Al4V alloy with SiO2 and SiO2-TiO2 intermediate coatings to Triceram low-fusing dental porcelain. METHODS: The multilayered systems were characterized from the standpoint of microstructure analysis (SEM), the mode of failure, the nature of bonding and the influence of intermediate coatings on the improvement of bond strength. The SiO2 and SiO2-TiO2 intermediate coatings were applied on the substrate materials by the sol-gel dipping technique. The metal-ceramic bond strength was investigated according to ISO 9693 standards using the three-point flexure bond test. RESULTS: Statistically significant higher bond strength of the metal-porcelain for Ti6A14V alloy (28.24 MPa), Ti6Al4V/SiO2 (32.17 MPa) and Ti6Al4V/SiO2-TiO2 (36.09 MPa) was noted in comparison to CPTi (23.04 MPa), CPTi/SiO2 (27.98 MPa) and CPTi/SiO2-TiO2 (28.84 MPa), respectively. The nature of metal-intermediate coating-porcelain bonding was both mechanical and chemical. The failure in all systems was cohesive and adhesive, mainly adhesive. SIGNIFICANCE: The application of SiO2 and SiO2-TiO2 intermediate coatings, produced by the sol-gel method, to both CPTi and Ti6Al4V alloy significantly improves the bond strength of metal-porcelain systems in comparison to the metal substrate only after sandblasting, and may have clinical use.