Lead Isolation and Capture in Perovskite Photovoltaics toward Eco-Friendly Commercialization.

Perovskite solar cells (PSCs) are developed rapidly in efficiency and stability in recent years, which can compete with silicon solar cells. However, an important obstacle to the commercialization of PSCs is the toxicity of lead ions (Pb2+) from water-soluble perovskites. The entry of free Pb2+ into organisms can cause severe harm to humans, such as blood lead poisoning, organ failure, etc. Therefore, this work reports a "lead isolation-capture" dual detoxification strategy with calcium disodium edetate (EDTA Na-Ca), which can inhibit lead leakage from PSCs under extreme conditions. More importantly, leaked lead exists in a nontoxic aggregation state chelated by EDTA. For the first time, in vivo experiments are conducted in mice to systematically prove that this material has a significant inhibitory effect on the toxicity of perovskites. In addition, this strategy can further enhance device performance, enabling the optimized devices to achieve an impressive power conversion efficiency (PCE) of 25.19%. This innovative strategy is a major breakthrough in the research on the prevention of lead toxicity in PSCs.

Bilateral Production Shield Enabling Highly Efficient Perovskite Photovoltaics.

Enhancing the intrinsic stability of perovskite and through encapsulation to isolate water, oxygen, and UV-induced decomposition are currently common and most effective strategies in perovskite solar cells. Here, the atomic layer deposition process is employed to deposit a nanoscale (≈100 nm), uniform, and dense Al2O3 film on the front side of perovskite devices, effectively isolating them from the erosion caused by water and oxygen in the humid air. Simultaneously, nanoscale (≈100 nm) TiO2 films are also deposited on the glass surface to efficiently filter out the ultraviolet (UV) light in the light source, which induces degradation in perovskite. Ultimately, throughthe collaborative effects of both aspects, the stability of the devices is significantly improved under conditions of humid air and illumination. As a result, after storing the devices in ambient air for 1000 h, the efficiency only declines to 95%, and even after 662 h of UV exposure, the efficiency remains at 88%, far surpassing the performance of comparison devices. These results strongly indicate that the adopted Al2O3 and TiO2 thin films play a significant role in enhancing the stability of perovskite solar cells, demonstrating substantial potential for widespread industrial applications.

Vertically Concentrated Quantum Wells Enabling Highly Efficient Deep-Blue Perovskite Light-Emitting Diodes.

Deep-blue perovskite light-emitting diodes (PeLEDs) based on quasi-two-dimensional (quasi-2D) systems exist heightened sensitivity to the domain distribution. The top-down crystallization mode will lead to a vertical gradient distribution of quantum well (QW) structure, which is unfavorable for deep-blue emission. Herein, a thermal gradient annealing treatment is proposed to address the polydispersity issue of vertical QWs in quasi-2D perovskites. The formation of large-n domains at the upper interface of the perovskite film can be effectively inhibited by introducing a low-temperature source in the annealing process. Combined with the utilization of NaBr to inhibit the undesirable n=1 domain, a vertically concentrated QW structure is ultimately attained. As a result, the fabricated device delivers a narrow and stable deep-blue emission at 458 nm with an impressive external quantum efficiency (EQE) of 5.82 %. Green and sky-blue PeLEDs with remarkable EQE of 21.83 % and 17.51 % are also successfully achieved, respectively, by using the same strategy. The findings provide a universal strategy across the entire quasi-2D perovskites, paving the way for future practical application of PeLEDs.

In Situ Hydrolysis of Phosphate Enabling Sky-Blue Perovskite Light-Emitting Diode with EQE Approaching 16.32.

The performance of blue perovskite light-emitting diodes (PeLEDs) lags behind the green and red counterparts owing to high trap density and undesirable red shift of the electroluminescence spectrum under operation conditions. Organic molecular additives were employed as passivators in previous reports. However, most commonly have limited functions, making it challenging to effectively address both efficiency and stability issues simultaneously. Herein, we reported an innovatively dynamic in situ hydrolysis strategy to modulate quasi-2D sky-blue perovskites by the multifunctional passivator phenyl dichlorophosphate that not only passivated the defects but also underwent in situ hydrolysis reaction to stabilize the emission. Moreover, hydrolysis products were beneficial for low-dimensional phase manipulation. Eventually, we obtained high-performance sky-blue PeLEDs with a maximum external quantum efficiency (EQE) of 16.32% and an exceptional luminance of 5740 cd m-2. More importantly, the emission peak of devices located at 485 nm remained stable under different biases. Our work signified the significant advancement toward realizing future applications of PeLEDs.

Photochemical Shield Enabling Highly Efficient Perovskite Photovoltaics.

Oxygen is difficult to be physically removed. Oxygen will be excited by light to form free radicals which further attack the lattice of perovskite. The stabilization of α-FAPbI3 against δ-FAPbI3 is the key to optimize perovskite solar cells. Herein, the simple molecule, benzaldehyde (BAH) is adopted. The photochemical shield will be established in perovskite layer. Moreover, heterogeneous nucleation induced by BAH enhances the crystallization of α-FAPbI3. Consequently, the stability of device is improved significantly. The target device maintains 95% of original power conversion efficiency after 1500 h under air conditions and light-emitting diode light. The power conversion efficiency increases from 23.21% of pristine device to 24.82% of target device.

Magnetic-biased chiral molecules enabling highly oriented photovoltaic perovskites.

The interaction between sites A, B and X with passivation molecules is restricted when the conventional passivation strategy is applied in perovskite (ABX3) photovoltaics. Fortunately, the revolving A-site presents an opportunity to strengthen this interaction by utilizing an external field. Herein, we propose a novel approach to achieving an ordered magnetic dipole moment, which is regulated by a magnetic field via the coupling effect between the chiral passivation molecule and the A-site (formamidine ion) in perovskites. This strategy can increase the molecular interaction energy by approximately four times and ensure a well-ordered molecular arrangement. The quality of the deposited perovskite film is significantly optimized with inhibited nonradiative recombination. It manages to reduce the open-circuit voltage loss of photovoltaic devices to 360 mV and increase the power conversion efficiency to 25.22%. This finding provides a new insight into the exploration of A-sites in perovskites and offers a novel route to improving the device performance of perovskite photovoltaics.

Electronically Manipulated Molecular Strategy Enabling Highly Efficient Tin Perovskite Photovoltaics.

Buried interface modification can effectively improve the compatibility between interfaces. Given the distinct interface selections in perovskite solar cells (PSCs), the applicability of a singular modification material remains limited. Consequently, in response to this challenge, we devised a tailored molecular strategy based on the electronic effects of specific functional groups. Therefore, we prepared three distinct silane coupling agents, and due to the varying inductive effects of these functional groups, the electronic distribution and molecular dipole moments of the coupling agents are correspondingly altered. Among them, trimethoxy (3,3,3-trifluoropropyl)-silane (F3 -TMOS), which possesses electron-withdrawing groups, generates a molecular dipole moment directed toward the hole transport layer (HTL). This approach changes the work function of the HTL, optimizes the energy level alignment, reduces the open-circuit voltage loss, and facilitates carrier transport. Furthermore, through the buffering effect of the coupling agent, the interface strain and lattice distortion caused by annealing the perovskite are reduced, enhancing the stability of the tin-based perovskite. Encouragingly, tin PSCs treated with F3 -TMOS achieved a champion efficiency of 14.67 %. This strategy provides an expedient avenue for the design of buried interface modification materials, enabling precise molecular adjustments in accordance with distinct interfacial contexts to ameliorate mismatched energetics and enhance carrier dynamics.

Biotoxicity of Halide Perovskites in Mice.

Halide perovskites are crystalline semiconductors with exceptional optoelectronic properties, rapidly developing toward large-scale applications. Lead (II) (Pb2+ ) is the core element used to prepare halide perovskites. Pb2+ can displace key 2+ elements, including calcium, zinc and iron, that regulate vital physiological functions. Sn2+ can replace Pb2+ within the perovskite structure and, if accidentally dispersed in the environment, it readily oxidizes to Sn4+ , which is compatible with physiological functions and thus potentially safe. The 3+ salt bismuth (III) (Bi3+ ) is also potentially safe for the same reason and useful to prepare double perovskites. Here, this work studies the biotoxicity of Pb, Sn, and Bi perovskites in mice for the first time. This work analyses histopathology and growth of mice directly exposed to perovskites and investigate the development of their offspring generation. This study provides the screening of organs and key physiological functions targeted by perovskite exposure to design specific studies in mammalians.

Characterizing Spatial and Energetic Distributions of Trap States Toward Highly Efficient Perovskite Photovoltaics.

Due to their greater opt electric performance, perovskite photovoltaics (PVs) present huge potential to be commercialized. Perovskite PV's high theoretical efficiency expands the available development area. The passivation of defects in perovskite films is crucial for approaching the theoretical limit. In addition to creating efficient passivation techniques, it is essential to direct the passivation approach by getting precise and real-time information on the trap states through measurements. Therefore, it is necessary to establish quantitative characterization methods for the trap states in energy and 3D spaces. The authors cover the characterization of the spatial and energy distributions of trap states in this article with an eye toward high-efficiency perovskite photovoltaics. After going over the strategies that have been created for characterizing and evaluating trap states, the authors will concentrate on how to direct the creative development of characterization techniques for trap states assessment and highlight the opportunities and challenges of future development. The 3D space and energy distribution mappings of trap states are anticipated to be realized. The review will give key guiding importance for further approaching the theoretical efficiency of perovskite photovoltaics, offering some future research direction and technological assistance for the development of appropriate targeted passivation technologies.

Ion-Dipole Interaction Enabling Highly Efficient CsPbI3 Perovskite Indoor Photovoltaics.

Metal halide perovskites are ideal candidates for indoor photovoltaics (IPVs) because of their easy-to-adjust bandgaps, which can be designed to cover the spectrum of any artificial light source. However, the serious non-radiative carrier recombination under low light illumination restrains the application of perovskite-based IPVs (PIPVs). Herein, polar molecules of amino naphthalene sulfonates are employed to functionalize the TiO2 substrate, anchoring the CsPbI3 perovskite crystal grains with a strong ion-dipole interaction between the molecule-level polar interlayer and the ionic perovskite film. The resulting high-quality CsPbI3 films with the merit of defect-immunity and large shunt resistance under low light conditions enable the corresponding PIPVs with an indoor power conversion efficiency of up to 41.2% (Pin : 334.11 µW cm-2 , Pout : 137.66 µW cm-2 ) under illumination from a commonly used indoor light-emitting diode light source (2956 K, 1062 lux). Furthermore, the device also achieves efficiencies of 29.45% (Pout : 9.80 µW cm-2 ) and 32.54% (Pout : 54.34 µW cm-2 ) at 106 (Pin : 33.84 µW cm-2 ) and 522 lux (Pin : 168.21 µW cm-2 ), respectively.

Buried Interface Passivation: A Key Strategy to Breakthrough the Efficiency of Perovskite Photovoltaics.

Owing to the merits of low cost and high power conversion efficiency (PCE), perovskite solar cells (PSCs) have become the best candidate to replace the commonly used silicon solar cells. However, PSCs have been slow to enter the market for a number of reasons, including poor stability, high toxicity, and rigorous preparation process. Passivation strategies including surface passivation and bulk passivation have been successfully applied to improve the device performance of PSCs. The passivation of the defects at the buried interface, which is regarded as a key strategy to breakthrough the device efficiency and stability of PSCs in the future, is ongoing with challenge. Herein, in detail the recent passivation of the buried interface is introduced from three aspects: perovskite layer, buried interlayer, and transport layer. The passivation effect of the buried interface is clearly demonstrated through three categories of salts, organics, and 2D materials. In addition, the transport layer is classified into electron transport layer (ETL) and hole transport layer (HTL). These classifications can help to have a clear understanding of substances which generate passivating effect and guide the continuous promotion of the follow-up buried interface passivating work.

Efficient Near-Infrared Electroluminescence from Lanthanide-Doped Perovskite Quantum Cutters.

Perovskite nanocrystals (PeNCs) deliver size- and composition-tunable luminescence of high efficiency and color purity in the visible range. However, attaining efficient electroluminescence (EL) in the near-infrared (NIR) region from PeNCs is challenging, limiting their potential applications. Here we demonstrate a highly efficient NIR light-emitting diode (LED) by doping ytterbium ions into a PeNCs host (Yb3+ : PeNCs), extending the EL wavelengths toward 1000 nm, which is achieved through a direct sensitization of Yb3+ ions by the PeNC host. Efficient quantum-cutting processes enable high photoluminescence quantum yields (PLQYs) of up to 126 % from the Yb3+ : PeNCs. Through halide-composition engineering and surface passivation to improve both PLQY and charge-transport balance, we demonstrate an efficient NIR LED with a peak external quantum efficiency of 7.7 % at a central wavelength of 990 nm, representing the most efficient perovskite-based LEDs with emission wavelengths beyond 850 nm.

Low-Dimensional Phase Regulation to Restrain Non-Radiative Recombination for Sky-Blue Perovskite LEDs with EQE Exceeding 15 .

Achieving efficient blue electroluminescence (EL) remains the fundamental challenge that impedes perovskite light-emitting diodes (PeLEDs) towards commercial applications. The bottleneck accounting for the inefficient blue PeLEDs is broadly attributed to the poor-emissive blue perovskite emitters based on either mixed halide engineering or reduced-dimensional strategy. Herein, we report the high-performing sky-blue PeLEDs (490 nm) with the maximum EQE exceeding 15 % by incorporating a molecular modifier, namely 4,4'-Difluorophenone, for significantly suppressing the non-radiative recombination and tuning of the low-dimensional phase distribution of quasi-2D blue perovskites, which represents a remarkable paradigm for developing the new generation of blue lighting sources.

Doping Strategies for Promising Organic-Inorganic Halide Perovskites.

Organic-inorganic halide perovskites (OIHPs) obtained tremendous attention due to their low cost and excellent properties. However, the stability and toxicity of Pb-based OIHPs (POIHPs), as well as the weakness of efficiency and stability in Sn-based OIHPs (SOIHPs), are still serious issues for commercial application. Notably, composition engineering is an effective and direct strategy for improving these issues along with the control and modification of properties. Recently, the doping strategies for POIHPs and SOIHPs are booming. Based on the relationship between properties and composition, the doping strategies for POIHPs and SOIHPs, aiming to provide a comprehensive review and guidance for the research are systematically summarized. Moreover, the doping strategies for Pb-Sn mixed OIHPs are also discussed. Finally, a brief perspective and conclusion toward future possible doping schemes and properties designment of POIHPs and SOIHPs are offered.

Light-Triggered Sustainable Defect-Passivation for Stable Perovskite Photovoltaics.

The generation of photoinduced defects and freely moving halogen ions is dynamically updated in real time. Accordingly, most reported strategies are static and short-term, which make their improvements in photostability very limited. Therefore, seeking new passivation strategies to match the dynamic characteristics of defect generation is very urgent. Without newly generated defects, a passivation molecule should exist in the configuration that would not become the initiation sites for defect generation. With newly generated defects, the passivation molecule should transfer into the other configuration that possesses the passivation sites. Herein, a classical photoisomeric molecule, spiropyran, is adopted, whose pre- and post-isomeric forms meet the requirements for two different configurations, to realize the state transition once the photoinduced defects appear during subsequent operation and dynamic capture for continuous renewal of defects. Consequently, spiropyrans work as light-triggered and self-healing sustainable passivation sites to realize continuous defect repair. The target devices retain 93% and 99% of their initial power conversion efficiencies after 456 h aging under ultraviolet illumination and 1200 h aging under full-spectrum illumination, respectively. This work provides a novel concept of sustainable passivation strategy to realize continuous defect-passivation and film-healing in perovskite photovoltaics.

Stabilized Low-Dimensional Species for Deep-Blue Perovskite Light-Emitting Diodes with EQE Approaching 3.4.

Despite recent encouraging developments, achieving efficient blue perovskite light-emitting diodes (PeLEDs) have been widely considered a critical challenge. The efficiency breakthrough only occurred in the sky-blue region, and the device performance of pure-blue and deep-blue PeLEDs lags far behind those of their sky-blue counterparts. To avoid the negative effects associated with dimensionality reduction and excess chloride typically needed to achieve deep-blue emission, here we demonstrate guanidine (GA+)-induced deep-blue (∼457 nm) perovskite emitters enabling spectrally stable PeLEDs with a record external quantum efficiency (EQE) over 3.41% through a combination of quasi-2D perovskites and halide engineering. Owing to the presence of GA+, even a small inclusion of chloride ions is sufficient for generating deep-blue electroluminescence (EL), in clear contrast to the previously reported deep-blue PeLEDs with significant chloride inclusion that negatively affects spectral stability. Based on the carrier dynamics analysis and theoretical calculation, GA+ is found to stabilize the low-dimensional species during annealing, retarding the cascade energy transfer and facilitating the deep-blue EL. Our findings open a potential third route to achieve deep-blue PeLEDs beyond the conventional methods of dimensionality reduction and excessive chloride incorporation.

Visualizing the Surface Photocurrent Distribution in Perovskite Photovoltaics.

Defect states play an important role in the photovoltaic performance of metal halide perovskites. Particularly, the passivation of surface defects has made great contributions to high-performance perovskite photovoltaics. This highlights the importance of understanding the surface defects from a fundamental level by developing more accurate and operando characterization techniques. Herein, a strategy to enable the surface carriers and photocurrent distributions on perovskite films to be visualized in the horizontal direction is put forward. The visual image of photocurrent distribution is realized by combining the static local distribution of carriers provided by scanning near-field optical microscopy with the dynamic transporting of carriers achieved via a scanning photocurrent measurement system. Taking a surface passivated molecule as an example, a comprehensive defect scene including static and dynamic as well as local and entire conditions is obtained using this strategy. The comprehensive analysis of the trap states in perovskite films is pioneered vertically and horizontally, which will powerfully promote the deep understanding of defect mechanisms and carrier behavior for the goal of fabricating high-performance perovskite optoelectronic devices.

Full-Dimensional Grain Boundary Stress Release for Flexible Perovskite Indoor Photovoltaics.

Perovskite photovoltaics are strong potential candidates to drive low-power off-grid electronics for indoor applications. Compared with rigid devices, flexible perovskite devices can provide a more suitable surface for indoor small electronic devices, enabling them have a broader indoor application prospect. However, the mechanical stability of flexible perovskite photovoltaics is an urgent issue solved. Herein, a kind of 3D crosslinking agent named borax is selected to carry out grain boundary penetration treatment on perovskite film to realize full-dimensional stress release. This strategy improves the mechanical and phase stabilities of perovskite films subjected to external forces or large temperature changes. The fabricated perovskite photovoltaics deliver a champion power conversion efficiency (PCE) of 21.63% under AM 1.5G illumination, which is the highest one to date. The merit of low trap states under weak light makes the devices present a superior indoor PCE of 31.85% under 1062 lux (LED, 2956 K), which is currently the best flexible perovskite indoor photovoltaic device. This work provides a full-dimensional grain boundary stress release strategy for highly stable flexible perovskite indoor photovoltaics.

Physical Fields Manipulation for High-Performance Perovskite Photovoltaics.

With the efforts of researchers from all over the world, metal halide perovskite solar cells (PSCs) have been booming rapidly in recent years. Generally, perovskite films are sensitive to surrounding conditions and will be changed under the action of physical fields, resulting in lattice distortion, degradation, ion migration, and so on. In this review, the progress of physical fields manipulation in PSCs, including the electric field, magnetic field, light field, stress field, and thermal field are reviewed. On this basis, the influences of these fields on PSCs are summarized and prospected. Finally, challenges and prospective research directions on how to make better use of external-fields while minimizing the unnecessary and disruptive impacts on commercial PSCs with high-efficiency and steady output are proposed.