Topographical and functional characterization of the ssDNA probe layer generated through EDC-mediated covalent attachment to nanocrystalline diamond using fluorescence microscopy.

The covalent attachment method for DNA on nanocrystalline diamond (NCD), involving the introduction of COOH functionalities on the surface by photoattachment of 10-undecenoic acid (10-UDA), followed by the 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC)-mediated coupling to NH 2-labeled ssDNA, is evaluated in terms of stability, density, and functionality of the resulting biological interface. This is of crucial importance in DNA biosensor development. The covalent nature of DNA attachment will infer the necessary stability and favorable orientation to the ssDNA probe molecules. Using confocal fluorescence microscopy, the influence of buffer type for the removal of excess 10-UDA and ssDNA, the probe ssDNA length, the probe ssDNA concentration, and the presence of the COOH-linker on the density and functionality of the ssDNA probe layer were investigated. It was determined that the most homogeneously dense and functional DNA layer was obtained when 300 pmol of short ssDNA was applied to COOH-modified NCD samples, while H-terminated NCD was resistant for DNA attachment. Exploiting this surface functionality dependence of the DNA attachment efficiency, a shadow mask was applied during the photochemical introduction of the COOH-functionalities, leaving certain regions on the NCD H-terminated. The subsequent DNA attachment resulted in a fluorescence pattern corresponding to the negative of the shadow mask. Finally, NCD surfaces covered with mixtures of the 10-UDA linker molecule and a similar molecule lacking the COOH functionality, functioning as a lateral spacer, were examined for their suitability in preventing nonspecific adsorption to the surface and in decreasing steric hindrance. However, purely COOH-modified NCD samples, patterned with H-terminated regions and treated with a controlled amount of probe DNA, proved the most efficient in fulfilling these tasks.

Towards a real-time, label-free, diamond-based DNA sensor.

Most challenging in the development of DNA sensors is the ability to distinguish between fully complementary target ssDNA (single-strand DNA) and 1-mismatch ssDNA. To deal with this problem, we performed impedance spectroscopy on DNA-functionalized nanocrystalline diamond (NCD) layers during hybridization and denaturation. In both reactions, a difference in behavior was observed for 1-mismatch target DNA and complementary target DNA in real-time. During real-time hybridization, a decrease of the impedance was observed at lower frequencies when the complementary target DNA was added, while the addition of 1-mismatch target ssDNA caused no significant change. Fitting these results to an electrical circuit demonstrates that this is correlated with a decrease of the depletion zone in the space charge region of the diamond. During real-time denaturation, differentiation between 1-mismatch and complementary target DNA was possible at higher frequencies. Denaturation of complementary DNA showed the longest exponential decay time of the impedance, while the decay time during 1-mismatch denaturation was the shortest. The real-time hybridization and denaturation experiments were carried out on different NCD samples in various buffer solutions at temperatures between 20 and 80 degrees C. It was revealed that the best results were obtained using a Microhyb hybridization buffer at 80 degrees C and 10x PCR buffer at 30 degrees C for hybridization and 0.1 M NaOH at temperatures above 40 degrees C for denaturation. We demonstrate that the combination of real-time hybridization spectra and real-time denaturation spectra yield important information on the type of target. This approach may allow a reliable identification of the mismatch sequence, which is the most biologically relevant.

EDC-mediated DNA attachment to nanocrystalline CVD diamond films.

Chemical vapour deposited (CVD) diamond is a very promising material for biosensor fabrication owing both to its chemical inertness and the ability to make it electrical semiconducting that allows for connection with integrated circuits. For biosensor construction, a biochemical method to immobilize nucleic acids to a diamond surface has been developed. Nanocrystalline diamond is grown using microwave plasma-enhanced chemical vapour deposition (MPECVD). After hydrogenation of the surface, 10-undecenoic acid, an omega-unsaturated fatty acid, is tethered by 254 nm photochemical attachment. This is followed by 1-ethyl-3-[3-dimethylaminopropyl]carbodiimide (EDC)-mediated attachment of amino (NH(2))-modified dsDNA. The functionality of the covalently bound dsDNA molecules is confirmed by fluorescence measurements, PCR and gel electrophoresis during 35 denaturation and rehybridisation steps. The linking method after the fatty acid attachment can easily be applied to other biomolecules like antibodies and enzymes.