Design of a new magnesium-based anterior cruciate ligament interference screw using finite element analysis.

BACKGROUND/OBJECTIVE: In anterior cruciate ligament â€‹reconstruction, a tendon graft, anchored by interference screws (IFSs), is frequently used as a replacement for the damaged ligament. Generally, IFSs are classified as being either metallic or polymeric. Metallic screws have sharp threads that lacerate the graft, preventing solid fixation. These constructs are difficult to image â€‹and can limit bone--screw integration because of the higher stiffness of the screw. Polymeric materials are often a better match to bone's material properties, but lack the strength needed to hold grafts in place. Magnesium (Mg) is a material of great promise for orthopaedic applications. Mg has mechanical properties similar to bone, ability to be seen on magnetic resonance imagings, and promotes bone healing. However, questions still remain regarding the strength of Mg-based screws. Previous ex vivo â€‹animal experiments found stripping of the screw drive when the full torque was applied to Mg screws during surgery, preventing full insertion and poor graft fixation. The similar design of the Mg screw led to questions regarding the relationship between material properties and design, and the ultimate impact on mechanical behaviour. Thus, the objective of this study was to analyze the stresses in the screw head, a key factor in the stripping mechanism of IFS, then use that information to improve screw design, for this material. METHODS: Using finite element analysis, a comparison study of six drive designs (hexagonal, quadrangle, torx, trigonal, trilobe, and turbine) was performed. This was followed by a parametric analysis to determine appropriate drive depth and drive width. RESULTS: It was observed that with a typical torque (2 â€‹Nm) used for screw insertion during anterior cruciate ligament reconstruction, the maximum von Mises and shear stress values were concentrated in the corners or turns of the drive, which could lead to stripping if the values were greater than the yield stress of Mg (193 â€‹MPa). With a four-time â€‹increase in drive depth to be fully driven and a 30% greater drive width, these maximum stress values were significantly decreased by more than 75%. CONCLUSION: It was concluded that improving the design of a Mg-based screw may increase surgical success rates, by decreasing device failure at insertion. THE TRANSLATIONAL POTENTIAL OF THIS ARTICLE: The results of this work have the potential to improve designs of degradable IFSs, allowing for greater torque to be applied and thus greater screw fixation between host bone and the graft. Such a fixation will allow greater integration, better patient healing, and ultimately improved patient outcomes.

Evaluation of a magnesium ring device for mechanical augmentation of a ruptured ACL: Finite element analysis.

BACKGROUND: Recently, a ring device was used for mechanical augmentation to aid the healing of ACL. In-vivo study using goat showed improved joint stability after ring repair in comparison to using biological augmentation alone. Objective of this study was to quantify the load and stress levels in the ACL and its femoral insertion site following ring repair. METHODS: A three dimensional finite element model of a goat stifle joint was developed to find the load and stress level in the ACL and at its femoral insertion site following ring repair. FINDINGS: Ring repair led to approximately a 50% reduction in anterior-posterior tibial translation over the model with a deficient ACL: 5.2 mm vs 10.6 mm, 4.4 mm vs 9.0 mm, and 2.9 mm vs 5.2 mm at joint flexion angles of 37°, 60° and 90° respectively. After ring repair, the in situ force in the ACL was restored to be nearly 60% of the intact ACL. The maximum Von Mises stress at the femoral insertion site was up to 71% of those for the intact ACL. INTERPRETATION: This study offers new knowledge on the function of a ring device to mechanically augment ACL repair in order to improve its healing. Quantitative data on loading levels in the repaired ACL and its insertion site that led to its healing could be used as basis for developing novel devices to mechanically augment the healing of ACL in humans.

Magnesium ring device to restore function of a transected anterior cruciate ligament in the goat stifle joint.

A bioresorbable, mono-crystalline magnesium (Mg) ring device and suture implantation technique were designed to connect the ends of a transected anterior cruciate ligament (ACL) to restabilize the knee and load the ACL to prevent disuse atrophy of its insertion sites and facilitate its healing. To test its application, cadaveric goat stifle joints were evaluated using a robotic/universal force-moment sensor testing system in three states: Intact, ACL-deficient, and after Mg ring repair, at 30°, 60°, and 90° of joint flexion. Under a 67-N anterior tibial load simulating that used in clinical examinations, the corresponding anterior tibial translation (ATT) and in-situ forces in the ACL and medial meniscus for 0 and 100 N of axial compression were obtained and compared with a control group treated with suture repair. In all cases, Mg ring repair reduced the ATT by over 50% compared to the ACL-deficient joint, and in-situ forces in the ACL and medial meniscus were restored to near normal levels, showing significant improvement over suture repair. These findings suggest that Mg ring repair could successfully stabilize the joint and load the ACL immediately after surgery, laying the framework for future in vivo studies to assess its utility for ACL healing. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:2001-2008, 2016.

Histological characteristics of ligament healing after bio-enhanced repair of the transected goat ACL.

BACKGROUND: Recently, healing of a ruptured anterior cruciate ligament (ACL) is reconsidered. In a previous study, we have shown that the transected ACL can heal after treatment with the triple X locking suture alone or combined with small intestine submucosa (SIS). The first research question of this study was whether the healing ACLs in both groups show histological characteristics that are typical for ligament healing. Secondly, did the combined treatment with SIS lead to improved histological healing, in terms of the morphology of the fibrous synovial layer, the extracellular matrix (ECM), collagen fiber orientation, cellularity, ratio of myofibroblasts, and collagen type 3 staining. The hypothesis was that SIS enhances the healing by the scaffolding effect, endogenous growth factors, and chemoattractants. METHODS: In the Suture group, the left ACL was transected and sutured with the triple X locking suture repair technique. In the Suture-SIS group, the left ACL underwent the same procedure with the addition of SIS. The right ACL served as internal control. Standard histology and immunostaining of α-smooth muscle actin (SMA) and collagen type 3 were used. RESULTS: Microscopy showed that the fibrous synovial layer around the ACL was reestablished in both groups. The collagen fibers in the Suture-SIS group stained denser, were more compactly arranged, and the ECM contained fewer voids and fat vacuoles. Neovasculature running between the collagen fibers was observed in both experimental groups. Collagen type 3 stained less in the Suture-SIS group. The cellularity in the Suture group, Suture-SIS group and Control was 1265 ± 1034 per mm(2), 954 ± 378 per mm(2), 254 ± 92, respectively; 49%, 26% and 20% of the cells stain positive for α-SMA, respectively. CONCLUSION: The healing ACL in both treated groups showed histological characteristics which are comparable to the spontaneously healing medial collateral ligament and showed that the ACL has a similar intrinsic healing response. Though, no definitive conclusions on the beneficial effects of the SIS scaffold on the healing process can be made.

Positive effects of an extracellular matrix hydrogel on rat anterior cruciate ligament fibroblast proliferation and collagen mRNA expression.

BACKGROUND/OBJECTIVE: We have previously shown that an extracellular matrix (ECM) bioscaffold derived from porcine small intestine submucosa (SIS) enhanced the healing of a gap injury of the medial collateral ligament as well as the central third defect of the patellar tendon. With the addition of a hydrogel form of SIS, we found that a transected goat anterior cruciate ligament (ACL) could also be healed. The result begs the research question of whether SIS hydrogel has positive effects on ACL fibroblasts (ACLFs) and thus facilitates ACL healing. METHODS: In the study, ECM-SIS hydrogel was fabricated from the digestion of decellularised and sterilised sheets of SIS derived from αGal-deficient (GalSafe) pigs. As a comparison, a pure collagen hydrogel was also fabricated from commercial collagen type I solution. The morphometrics of hydrogels was assessed with scanning electron microscopy. The ECM-SIS and collagen hydrogels had similar fibre diameters (0.105 ± 0.010 µm vs. 0.114 ± 0.004 µm), fibre orientation (0.51 ± 0.02 vs. 0.52 ± 0.02), and pore size (0.092 ± 0.012 µm vs. 0.087 ± 0.008 µm). The preservation of bioactive properties of SIS hydrogel was assessed by detecting bioactive molecules sensitive to processing and enzyme digestion, such as growth factors fibroblast growth factor-2 (FGF-2) and transforming growth factor-beta 1 (TGF-ß1), with enzyme-linked immunosorbent assay. ACLFs were isolated and expanded in culture from explants of rat ACLs (n = 3). The cells were then seeded on the hydrogels and cultured with 0%, 1%, and 10% foetal bovine serum (FBS) for 3 days and 7 days. Cell attachment was observed using a light microscope and scanning electron microscopy, whereas cell proliferation and matrix production (collagen types I and III) were examined with bromodeoxyuridine assays and reverse transcription-polymerase chain reaction, respectively. RESULTS: The results showed that FGF-2 and TGF-ß1 in the SIS hydrogel were preserved by 50% (65.9 ± 26.1 ng/g dry SIS) and 90% (4.4 ± 0.6 ng/g dry SIS) relative to their contents in ECM-SIS sheets, respectively. At Day 3 of culture, ACLFs on the SIS hydrogel were found to proliferate 39%, 31%, and 22% more than those on the pure collagen hydrogel at 0%, 1%, and 10% FBS, respectively (p < 0.05). Collagen type I mRNA expression was increased by 150%, 207%, and 100%, respectively, compared to collagen hydrogel (p < 0.05), whereas collagen type III mRNA expression was increased by 123% and 132% at 0% and 1% FBS, respectively (all p < 0.05) but not at 10% FBS. By Day 7, collagen type I mRNA expression was still elevated by 137% and 100% compared to collagen hydrogel at 1% and 10% FBS, respectively (p < 0.05). Yet, collagen type III mRNA levels were not significantly different between the two groups at any FBS concentrations. CONCLUSION: Our data showed that the ECM-SIS hydrogel not only supported the growth of ACLFs, but also promoted their proliferation and matrix production relative to a pure collagen hydrogel. As such, ECM-SIS hydrogel has potential therapeutic value to facilitate ACL healing at the early stage after injury.

Biomechanical evaluation of the quadriceps tendon autograft for anterior cruciate ligament reconstruction: a cadaveric study.

BACKGROUND: Recently, many surgeons have chosen the quadriceps tendon (QT) as an autograft for anterior cruciate ligament (ACL) reconstruction. However, there have not been biomechanical studies that quantitatively evaluated knee function after reconstruction using a QT autograft. PURPOSE: To measure the 6 degrees of freedom knee kinematics and in situ graft forces after reconstruction with a QT autograft compared with a quadrupled semitendinosus and gracilis (QSTG) tendon autograft. STUDY DESIGN: Controlled laboratory study. METHODS: Ten human cadaveric knees (age, 54-64 years) were tested in 3 conditions: (1) intact, (2) ACL deficient, and (3) after ACL reconstruction using a QT or QSTG autograft. With use of a robotic/universal force-moment sensor testing system, knee kinematics and in situ forces in the ACL and autografts were obtained at 5 knee flexion angles under externally applied loads: (1) 134-N anterior tibial load, (2) 134-N anterior tibial load with 200-N axial compression, and (3) 10-N·m valgus and 5-N·m internal tibial torque. RESULTS: Under the anterior tibial load, both autografts restored anterior tibial translation to within 2.5 mm of the intact knee and in situ forces to within 20 N of the intact ACL at 15°, 30°, and 60°. Adding compression did not change these findings. With the combined rotatory load, the anterior tibial translation and graft in situ forces were again not significantly different from the intact ACL. There were no significant differences between the grafts under any experimental condition. CONCLUSION: Reconstruction of the ACL with a QT autograft restored knee function to similar levels as that reconstructed with a QSTG autograft under loads simulating clinical examinations. CLINICAL RELEVANCE: The positive biomechanical results of this cadaveric study lend support to the use of a QT autograft for ACL reconstruction, as it could restore knee function immediately after surgery under applied loads that mimic clinical examinations.

Tensile properties of the medial patellofemoral ligament: the effect of specimen orientation.

For recurrent patellar dislocation, reconstruction of the medial patellofemoral ligament (MPFL) with replacement autografts has often been performed but with only little data on the tensile properties of the MPFL to guide graft selection. With its complex anatomy and geometry, these properties are difficult to obtain. In this study, we showed how the orientation of the femur-MPFL-patella complex (FMPC) during uniaxial tensile testing can have a significant effect on its structural properties. Twenty two FMPCs were isolated from porcine stifle joints and randomly assigned to two groups of 11 each. For the first group, the specimens were loaded to failure with the patella oriented 30 degrees away from the direction of the applied load to mimic its orientation in situ, called natural orientation. In the second group, the patella was aligned in the direction of the tensile load, called non-natural orientation. The stiffness for the natural orientation group was 65±13 N/mm, 32% higher than that for the non-natural orientation group (50±17 N/mm; p<0.05). The ultimate loads were 438±128 N and 386±136 N, respectively (p>0.05). Ten out of 11 specimens in the natural orientation group failed at the femoral attachment (the narrowest portion of the MPFL) compared to 6 out of 11 in the non-natural orientation group. Our findings suggest that the specimen orientation that mimics the in-situ loading conditions of the MPFL should be used to obtain more representative data for the structural properties of the FMPC.

Revolutionizing orthopaedic biomaterials: The potential of biodegradable and bioresorbable magnesium-based materials for functional tissue engineering.

In recent years, there has been a surge of interest in magnesium (Mg) and its alloys as biomaterials for orthopaedic applications, as they possess desirable mechanical properties, good biocompatibility, and biodegradability. Also shown to be osteoinductive, Mg-based materials could be particularly advantageous in functional tissue engineering to improve healing and serve as scaffolds for delivery of drugs, cells, and cytokines. In this paper, we will present two examples of Mg-based orthopaedic devices: an interference screw to accelerate ACL graft healing and a ring to aid in the healing of an injured ACL. In vitro tests using a robotic/UFS testing system showed that both devices could restore function of the goat stifle joint. Under a 67-N anterior tibial load, both the ACL graft fixed with the Mg-based interference screw and the Mg-based ring-repaired ACL could restore anterior tibial translation (ATT) to within 2mm and 5mm, respectively, of the intact joint at 30°, 60°, and 90° of flexion. In-situ forces in the replacement graft and Mg-based ring-repaired ACL were also similar to those of the intact ACL. Further, early in vivo data using the Mg-based interference screw showed that after 12 weeks, it was non-toxic and the joint stability and graft function reached similar levels as published data. Following these positive results, we will move forward in incorporating bioactive molecules and ECM bioscaffolds to these Mg-based biomaterials to test their potential for functional tissue engineering of musculoskeletal and other tissues.

Healing of the goat anterior cruciate ligament after a new suture repair technique and bioscaffold treatment.

Primary suture repair of the anterior cruciate ligament (ACL) has been used clinically in an attempt to heal the ruptured ACL. The results, however, were not satisfactory, which in retrospect can be attributed to the used suturing technique and the suboptimal healing conditions. These constraining conditions can be improved by introducing a new suturing technique and by using small intestinal submucosa (SIS) as a bioscaffold. It is hypothesized that the suturing technique keep the torn ends together and that SIS enhance and promote the healing of the ACL. The goat was used as the study model. In the Suture group, the left ACL was transected and suture repaired with a new locking suture repair technique (n=5) allowing approximation and fixation under tension. The Suture-SIS group underwent the same procedure with the addition of SIS (n=5). The right ACL served as control. After 12 weeks of healing, anterior-posterior translation and in situ force of the healing ACL were measured, followed by the measurement of the cross-sectional area and structural stiffness. Routine histology was performed on tissue samples. Gross morphology showed that the healing ACL was continuous with collagenous tissue in both groups. The cross-sectional area of the Suture and the Suture-SIS group was 35% and 50% of the intact control, respectively. The anterior-posterior translations at different flexion angles were statistically not different between the Suture group and the Suture-SIS group. Only the in situ force at 30° in the Suture-SIS group was higher than in the Suture group. Tensile tests showed that the stiffness for the Suture group was not different from the Suture-SIS group (31.1±8.1 N/mm vs. 41.9±18.0 N/mm [p>0.05]). Histology showed longitudinally aligned collagen fibers from origo to insertion. More fibroblasts were present in the healing tissue than in the control intact tissue. The study demonstrated the proof of concept of ACL repair in a goat model with a new suture technique and SIS. The mechanical outcome is not worse than previously reported for ACL reconstruction. In conclusion, the approach of using a new suture technique, with or without a bioscaffold to heal the ACL is promising.

Myeloid-derived suppressor cells as a vehicle for tumor-specific oncolytic viral therapy.

One of the several impediments to effective oncolytic virus therapy of cancer remains a lack of tumor-specific targeting. Myeloid-derived suppressor cells (MDSC) are immature myeloid cells induced by tumor factors in tumor-bearing hosts. The biodistribution kinetics of MDSC and other immune cell types in a murine hepatic colon cancer model was investigated through the use of tracking markers and MRI. MDSCs were superior to other immune cell types in preferential migration to tumors in comparison with other tissues. On the basis of this observation, we engineered a strain of vesicular stomatitis virus (VSV), an oncolytic rhabdovirus that bound MDSCs and used them as a delivery vehicle. Improving VSV-binding efficiency to MDSCs extended the long-term survival of mice bearing metastatic colon tumors compared with systemic administration of wild-type VSV alone. Survival was further extended by multiple injections of the engineered virus without significant toxicity. Notably, direct tumor killing was accentuated by promoting MDSC differentiation towards the classically activated M1-like phenotype. Our results offer a preclinical proof-of-concept for using MDSCs to facilitate and enhance the tumor-killing activity of tumor-targeted oncolytic therapeutics.

High knee valgus in female subjects does not yield higher knee translations during drop landings: a biplane fluoroscopic study.

The goal of this study was to determine the effects of peak knee valgus angle and peak knee abductor moment on the anterior, medial, and lateral tibial translations (ATT, MTT, LTT) in the "at risk" female knee during drop landing. Fifteen female subjects performed drop landings from 40 cm. Three-dimension knee motion was simultaneously recorded using a high speed, biplane fluoroscopy system, and a video-based motion analysis system. Valgus knee angles and knee abduction moments were stratified into low, intermediate, and high groups and peak ATT, MTT, and LTT were compared between these groups with ANOVA (α = 0.05). Significant differences were observed between stratified groups in peak knee valgus angle (p < 0.0001) and peak knee abduction moment (p < 0.0001). However, no corresponding differences in peak ATT, LTT, and MTT between groups exhibiting low to high-peak knee valgus angles (ATT: p = 0.80; LTT: p = 0.25; MTT: p = 0.72); or, in peak ATT (p = 0.61), LTT (p = 0.26) and MTT (p = 0.96) translations when stratified according to low to high knee abduction moments, were found. We conclude that the healthy female knee is tightly regulated with regard to translations even when motion analysis derived knee valgus angles and abduction moments are high.

The potential of recombinant vesicular stomatitis virus-mediated virotherapy against metastatic colon cancer.

Colorectal cancer (CRC) is the fourth most frequently diagnosed cancer and the second leading cause of cancer-related mortality in the United States. The liver and lung are the most common sites of distant metastasis of CRC. The approval of newer chemotherapeutic agents such as oxaliplatin, irinotecan, bevacizumab, cetuximab and panitumumab has significantly improved survival, yet the majority of patients still succumb to the disease in less than 2 years. Novel therapeutic agents that can provide significant clinical benefit for metastatic CRC patients are needed. Oncolytic vesicular stomatitis virus (VSV) is a promising tool as a cancer therapeutic agent. In this study, we examined the feasibility of repeated intravenous infusions of rVSV in multiple CRC lung metastases, compared with repeated hepatic arterial administration in multifocal CRC liver metastasis in immune competent rats. We established a multifocal liver metastases model or the multiple lung metastases model using a CRC cell line, RCN-H4, implanted into syngeneic F344/DuCrj rats. 4.0x10(6) plaque-forming units (pfu) of recombinant VSV vectors expressing mutant (L289A) Newcastle disease virus fusion protein [rVSV-NDV/F(L289A)] were administered 3 times for 3 consecutive days locally via the hepatic artery for liver metastases or systemically via the penial vein for lung metastases. In the liver metastasis model, significantly enhanced survival was observed with rVSV-NDV/F(L289A)-treated rats (P=0.0196). Median survival was 110 and 25 days, respectively. In addition, 4 out of 7 of the rVSV-NDV/F(L289A)-treated rats demonstrated long-term survival exceeding 100 days. The long-term surviving rats were sacrificed to evaluate for residual malignancy. Liver tumors were not detected. In the lung metastasis model, median survival was 10 [VSV-NDV/F(L289A)-treated rats] and 7 days (control). Although survival was significantly prolonged (P<0.001), none of the rats achieved long-term survival. VSV virotherapy has potential for CRC liver and lung metastases, although systemic venous delivery is much less effective than locoregional delivery such as hepatic arterial infusion.

Fiber orientation of the transverse carpal ligament.

The transverse carpal ligament is the volar roof of the carpal tunnel. Gross observation shows that the ligament appears to have fibers that roughly orient in the transverse direction. A closer anatomical examination shows that the ligament also has oblique fibers. Knowledge of the fiber orientation of the transverse carpal ligament is valuable for further understanding the ligament's role in regulating the structural function of the carpal tunnel. The purpose of this study is to quantify collagen fiber orientation within the transverse carpal ligament using the small angle light scattering technique. Eight transverse carpal ligament samples from cadaver hands were used in this study. Individual 20-µm sections were cut evenly along the thickness of the transverse carpal ligament. Sections of three thickness levels (25%, 50%, and 75% from the volar surface) were collected for each transverse carpal ligament. Fibers were grouped in the following orientation ranges: transverse, longitudinal, oblique in the pisiform-trapezium (PT), and oblique in the scaphoid-hamate (SH) directions. In analyzing the fiber percentages, the orientation types for the different thickness levels of the ligament showed that the transverse fibers were the most prominent (>60.7%) followed by the PT oblique (18.6%), SH oblique (13.0%), and longitudinal (8.6%) fibers.

Potential of healing a transected anterior cruciate ligament with genetically modified extracellular matrix bioscaffolds in a goat model.

PURPOSE: Biological augmentation to heal a torn anterior cruciate ligament (ACL) has gained significant interest. This study examined the potential advantages of using extracellular matrix (ECM) bioscaffolds from galactosyl-α(1,3)galactose deficient pigs to heal the transected ACL. METHODS: In 16 skeletally mature goats, the ACL in the right hindlimb was transected and repaired. In 9 of these animals, an ECM sheet was wrapped around the injury site and with an ECM hydrogel injected into the transected site. The remaining 7 animals were treated with suture repair only. The left hindlimb served as a sham-operated control. RESULTS: After 12 weeks, the healing ACL in the ECM-treated group showed an abundance of continuous neo-tissue formation, while only limited tissue growth was found after suture repair only. The cross-sectional area of the ACL from the ECM-treated group was similar to sham-operated controls (n.s.) and was 4.5 times those of the suture repair group (P < 0.05). The stiffness of the femur-ACL-tibia complexes from the ECM-treated group was 2.4 times those of the suture repair group (P < 0.05). Furthermore, these values reached 48% of the sham-operated controls (53 ± 19 N/mm and 112 ± 21 N/mm, respectively, P < 0.05). CONCLUSIONS: The application of an ECM bioscaffold and hydrogel was found to accelerate the healing of a transected ACL following suture repair in the goat model with limited tissue hypertrophy and improvement in some of its biomechanical properties. Although more work is necessary to fully restore the function of the normal ACL, these early results offer a potential new approach to aid ACL healing.

In vivo tibiofemoral kinematics during 4 functional tasks of increasing demand using biplane fluoroscopy.

BACKGROUND: The anterior cruciate ligament (ACL) has been well defined as the main passive restraint to anterior tibial translation (ATT) in the knee and plays an important role in rotational stability. However, it is unknown how closely the ACL and other passive and active structures of the knee constrain translations and rotations across a set of functional activities of increasing demand on the quadriceps. HYPOTHESIS: Anterior tibial translation and internal rotation of the tibia relative to the femur would increase as the demand on the quadriceps increased. STUDY DESIGN: Controlled laboratory study. METHODS: The in vivo 3-dimensional knee kinematics of 10 adult female patients (height, 167.8 ± 7.1 cm; body mass, 57 ± 4 kg; body mass index [BMI], 24.8 ± 1.7 kg/m(2); age, 29.7 ± 7.9 years) was measured using biplane fluoroscopy while patients completed 4 functional tasks. The tasks included an unloaded knee extension in which the patient slowly extended the knee from 90° to 0° of flexion in 2 seconds; walking at a constant pace of 90 steps per minute; a maximum effort isometric knee extension with the knee at 70° of flexion; and landing from a height of 40 cm in which the patient stepped off a box, landed, and immediately performed a maximum effort vertical jump. RESULTS: Landing (5.6 ± 1.9 mm) produced significantly greater peak ATT than walking (3.1 ± 2.2 mm) and unweighted full extension (2.6 ± 2.1 mm) (P < .01), but there was no difference between landing and a maximum isometric contraction (5.0 ± 1.9 mm). While there was no significant difference in peak internal rotation between landing (19.4° ± 5.7°), maximum isometric contraction (15.9° ± 6.7°), and unweighted full knee extension (14.5° ± 7.7°), each produced significantly greater internal rotation than walking (3.9° ± 4.2°) (P < .001). Knee extension torque significantly increased for each task (P < .01): unweighted knee extension (4.7 ± 1.2 N·m), walking (36.5 ± 7.9 N·m), maximum isometric knee extension (105.1 ± 8.2 N·m), and landing (140.2 ± 26.2 N·m). CONCLUSION: Anterior tibial translations significantly increased as demand on the quadriceps and external loading increased. Internal rotation was not significantly different between landing, isometric contraction, and unweighted knee extension. Additionally, ATT and internal rotation from each motion were within the normal range, and no excessive amounts of translation or rotation were observed. CLINICAL RELEVANCE: This study demonstrated that while ATT will increase as demand on the quadriceps and external loading increases, the knee is able to effectively constrain ATT and internal rotation. This suggests that the healthy knee has a safe envelope of function that is tightly controlled even though task demand is elevated.

Relationship of knee shear force and extensor moment on knee translations in females performing drop landings: a biplane fluoroscopy study.

BACKGROUND: Research has linked knee extensor moment and knee shear force to the non-contact anterior cruciate ligament injury during the landing motion. However, how these biomechanical performance factors relate to knee translations in vivo is not known as knee translations cannot be obtained with traditional motion capture techniques. The purpose of this study was to combine traditional motion capture with high-speed, biplane fluoroscopy imaging to determine relationships between knee extensor moment and knee shear force profiles with anterior and lateral tibial translations occurring during drop landing in female athletes. METHODS: 15 females performed drop landings from a height of 40 cm while being recorded using a high speed, biplane fluoroscopy system and simultaneously being recorded using surface marker motion capture techniques to estimate knee joint angle, reaction force and moment profiles. FINDINGS: No significant statistical relationships were observed between peak anterior or posterior knee shear force and peak anterior and lateral tibial translations; or, between peak knee extensor moment and peak anterior and lateral tibial translations. Although differences were noted in peak shear force (P=0.02) and peak knee extensor moment (P<0.001) after stratification into low and high shear force and moment cohorts, no differences were noted in anterior and lateral tibial translations (all P ≥ 0.18). INTERPRETATION: Females exhibiting high knee extensor moment and knee shear force during drop landings do not yield correspondingly high anterior and lateral tibial translations.

Measurements of tibiofemoral kinematics during soft and stiff drop landings using biplane fluoroscopy.

BACKGROUND: Previous laboratory studies of landing have defined landing techniques in terms of soft or stiff landings according to the degree of maximal knee flexion angle attained during the landing phase and the relative magnitude of the ground-reaction force. Current anterior cruciate ligament injury prevention programs are instructing athletes to land softly to avoid excessive strain on the anterior cruciate ligament. PURPOSE: This study was undertaken to measure, describe, and compare tibiofemoral rotations and translations of soft and stiff landings in healthy individuals using biplane fluoroscopy. STUDY DESIGN: Controlled laboratory study. METHODS: The in vivo, lower extremity, 3-dimensional knee kinematics of 16 healthy adults (6 male and 10 female) instructed to land softly and stiffly in different trials were collected in biplane fluoroscopy as they performed the landing from a height of 40 cm. RESULTS: Average and maximum relative anterior tibial translation (average, 2.8 ± 1.2 mm vs 3.0 ± 1.4 mm; maximum, 4.7 ± 1.6 mm vs 4.4 ± 0.8 mm), internal/external rotation (average, 3.7° ± 5.1° vs 2.7° ± 4.3°; maximum, 5.6° ± 5.5° vs 4.9° ± 4.7°), and varus/valgus (average, 0.2° ± 1.2° vs 0.2° ± 1.0°; maximum, 1.7° ± 1.2° vs 1.6° ± 0.9°) were all similar between soft and stiff landings, respectively. The peak vertical ground-reaction force was significantly larger for stiff landings than for soft landings (2.60 ± 1.32 body weight vs 1.63 ± 0.73; P < .001). The knee flexion angle total range of motion from the minimum angle at contact to the maximum angle at peak knee flexion was significantly greater for soft landings than for stiff (55.4° ± 8.8° vs 36.8° ± 11.1°; P < .01). CONCLUSION: Stiff landings, as defined by significantly lower knee flexion angles and significantly greater peak ground-reaction forces, do not result in larger amounts of anterior tibial translation or knee rotation in either varus/valgus or internal/external rotation in healthy individuals. CLINICAL RELEVANCE: In healthy knees, the musculature and soft tissues of the knee are able to maintain translations and rotations within a small, safe range during controlled landing tasks of differing demand. The knee kinematics of this healthy population will serve as a comparison for injured knees in future studies. It should be stressed that because the authors did not compare how the loads were distributed over the soft tissues of the knee between the 2 landing styles, the larger ground-reaction forces and more extended knee position observed during stiff landings should still be considered dangerous to the anterior cruciate ligament and other structures of the lower extremities, particularly in competitive settings where movements are often unanticipated.

Suture augmentation following ACL injury to restore the function of the ACL, MCL, and medial meniscus in the goat stifle joint.

Functional tissue engineering (FTE) approaches have shown promise in healing an injured anterior cruciate ligament (ACL) of the knee. Nevertheless, additional mechanical augmentation is needed to maintain joint stability and appropriate loading of the joint while the ACL heals. The objective of this study was to quantitatively evaluate how mechanical augmentation using sutures restores the joint kinematics as well as the distribution of loading among the ACL, medial collateral ligament, and medial meniscus (MM) in response to externally applied loads. Eight goat stifle joints were tested on a robotic/universal force-moment sensor testing system under two loading conditions: (1) a 67N anterior tibial load (ATL) and (2) a 67N ATL with 100N axial compression. For each joint, four experimental conditions were tested at 30°, 60°, and 90° of flexion: the (1) intact and (2) ACL-deficient joint, as well as following (3) suture repair of the transected ACL, and (4) augmentation using sutures passed from the femur to the tibia. Under the 67N ATL, suture augmentation could restore the anterior tibial translation (ATT) to within 3mm of the intact joint (p>0.05), representing a 54-76% improvement over suture repair (p<0.05). With the additional axial compression, the ATT and in-situ forces of the sutures following suture augmentation remained 2-3 times closer to normal (p<0.05). Also, the in-situ forces in the MM were 58-73% lower (p<0.05). Thus, suture augmentation may be helpful in combination with FTE approaches for ACL healing by providing the needed initial joint stability while lowering the loads on the MM.