Puffing Up Hollow Carbon Nanofibers with High-Energy Metal-Organic Frameworks for Capacitive-Dominated Potassium-Ion Storage.

Nitrogen-doped carbon materials with abundant defects and strong potassium adsorption ability have been recognized as potential anodes for potassium ion batteries (PIBs). However, the limited content and uncontrolled type of nitrogen-doped sites hinder the further performance improvement of PIBs. Herein, this work proposes nitrogen phosphorous co-doped hollow carbon nanofibers (PNCNFs) derived from high-energy metal-organic frameworks (MOFs) with an ultra-high nitrogen content of 19.52 wt% and a high portion of more reactive pyridinic N sites. Furthermore, the highly open architecture exploded by released gases from high-energy MOFs provides sufficient edge sites to settle the N atoms and further form pyridinic N sites induced by phosphorous dopants. The resulting PNCNFs achieve excellent potassium ion storage performance with high reversible capacity (466.2 mAh g-1 ), superb rate capability (244.4 mAh g-1 at 8 A g-1 ), and excellent cycling performance (294.6 mAh g-1 after 3250 cycles). The density functional theory calculation reveals that the N/P defects enhance the potassium adsorption ability and improve the conductivity.

Tailoring Amine-Functionalized Ti-MOFs via a Mixed Ligands Strategy for High-Efficiency CO2 Capture.

Amine-functionalized metal-organic frameworks (MOFs) are a promising strategy for the high-efficiency capture and separation of CO2. In this work, by tuning the ratio of 1,3,5-benzenetricarboxylic acid (H3BTC) to 5-aminoisophthalic acid (5-NH2-H2IPA), we designed and synthesized a series of amine-functionalized highly stable Ti-based MOFs (named MIP-207-NH2-n, in which n represents 15%, 25%, 50%, 60%, and 100%). The structural analysis shows that the original framework of MIP-207 in the MIP-207-NH2-n (n = 15%, 25%, and 50%) MOFs remains intact when the mole ratio of ligand H3BTC to 5-NH2-H2IPA is less than 1 to 1 in the resulting MOFs. By the introduction of amino groups, MIP-207-NH2-25% demonstrates outstanding CO2 capture performance up to 3.96 and 2.91 mmol g-1, 20.7% and 43.3% higher than those of unmodified MIP-207 at 0 and 25 °C, respectively. Furthermore, the breakthrough experiment indicates that the dynamic CO2 adsorption capacity and CO2/N2 separation factors of MIP-207-NH2-25% are increased by about 25% and 15%, respectively. This work provides an additional strategy to construct amine-functionalized MOFs with the maintenance of the original MOF structure and high performance of CO2 capture and separation.

A Metal-Organic Framework Nanorod-Assembled Superstructure and Its Derivative: Unraveling the Fast Potassium Storage Mechanism in Nitrogen-Modified Micropores.

3D carbon-based materials with multiscale hierarchy are promising electrode materials for electrochemical energy storage and conversion applications, but the synthesis in an efficient and large-scale way is still a great challenge. Herein, a carbon nanorod-assembled 3D superstructure is facilely fabricated by morphology-preserving conversion of a metal-organic framework (MOF) nanorod-assembled superstructure. The MOF superstructure can be fabricated in one-pot synthesis with high reproducibility and high yield by precise control of the MOF nucleation and growth. Its derived carbon inherits the nanorod-assembled superstructure and possesses abundant micropores and nitrogen doping, which can serve as a high-performance anode material for fast potassium storage. The superiority of the superstructure and the synergism of micropore capturing and nitrogen anchoring are verified both experimentally and theoretically.

Nanobundles of Iron Phosphide Fabricated by Direct Phosphorization of Metal-Organic Frameworks as an Efficient Hydrogen-Evolving Electrocatalyst.

Transition-metal-based phosphides (TMPs) have been considered as attractive electrocatalysts for water splitting due to their earth-abundance and remarkable catalytic activity. As a representative type of precursors, metal-organic frameworks (MOFs) provide ideal plateaus for the design of nanostructured TMPs. In this work, the hierarchically structured iron phosphide nanobundles (FeP-500) were fabricated by one-step phosphorization of an iron-based MOF (MET(Fe)) precursor. The derived FeP-500 nanobundles were constructed by quasi-paralleled one-dimensional nanorods with uneven surface, which provided channels for electrolyte penetration, mass transport, and effective exposure of active sites during the water-splitting process. With the addition of conductive Super P, the obtained FeP-500-S exhibited a good electrocatalytic performance towards the hydrogen evolution reaction in alkaline electrolyte (1 mol L-1 KOH). Furthermore, to investigate the influence of secondary metal doping, a series of isoreticular MOF precursors and bimetallic TMPs were fabricated. The results indicated that the catalytic performance is structure dominated.

Antiperovskite Intermetallic Nanoparticles for Enhanced Oxygen Reduction.

Antiperovskite Co3 InC0.7 N0.3 nanomaterials with highly enhanced oxygen reduction reaction (ORR) performance were prepared by tuning nitrogen contents through a metal-organic framework (MOF)-derived strategy. The nanomaterial surpasses all reported noble-metal-free antiperovskites and even most perovskites in terms of onset potential (0.957 V at J=0.1 mA cm-2 ) and half-wave potential (0.854 V). The OER and zinc-air battery performance demonstrate its multifunctional oxygen catalytic activities. DFT calculation was performed and for the first time, a 4 e- dissociative ORR pathway on (200) facets of antiperovskite was revealed. Free energy studies showed that nitrogen substitution could strengthen the OH desorption as well as hydrogenation that accounts for the enhanced ORR performance. This work expands the scope for material design via tailoring the nitrogen contents for optimal reaction free energy and hence performance of the antiperovskite system.

Gas-Permeable, Irritation-Free, Transparent Hydrogel Contact Lens Devices with Metal-Coated Nanofiber Mesh for Eye Interfacing.

An electronic "smart" contact lens device with high gas permeability and optical transparency, as well as mechanical compliance and robustness, offers daily wear capability in eye interfacing and can have broad applications ranging from ocular diagnosis to augmented reality. Most existing contact lens electronics utilize gas-impermeable substrates, electronic components, and interfacial adhesion layers, which impedes them from applications requiring continuous daily wear. Here we report on the design and fabrication of an eye interfacing device with a commercial ocular contact lens as the substrate, metal-coated nanofiber mesh as the conductor, and in situ electrochemically deposited poly(3,4-ethylenedioxythiophene) (PEDOT) /poly(styrene sulfonate) (PSS) as the adhesion material. This hydrogel contact lens device shows high gas permeability, wettability, and level of hydration, in addition to excellent optical transparency, mechanical compliance, and robustness. Using a rabbit model, we found that the animals wearing these hydrogel contact lens devices continuously for 12 hours showed a level of corneal fluorescein staining comparable to those wearing pure hydrogel contact lenses for same period of time, with no obvious corneal abrasion or irritation, indicating their high level of safety for continuous daily wear. Finally, full-field electroretinogram (ERG) recordings on rabbits were carried out to demonstrate the functionality of this device. We believe that the strategy of integrating nanofiber mesh-based electronic components demonstrated here can offer a general platform for hydrogel electronics with the advantages of preserving the physiological and mechanical properties of the hydrogel, thus enabling seamless integration with biological tissues and providing various wearable or implantable sensors with improved biocompatibility for health monitoring or medical treatment.

Synergistic Effect of Co-Ni Hybrid Phosphide Nanocages for Ultrahigh Capacity Fast Energy Storage.

Rational design of metal compounds in terms of the structure/morphology and chemical composition is essential to achieve desirable electrochemical performances for fast energy storage because of the synergistic effect between different elements and the structure effect. Here, an approach is presented to facilely fabricate mixed-metal compounds including hydroxides, phosphides, sulfides, oxides, and selenides with well-defined hollow nanocage structure using metal-organic framework nanocrystals as sacrificial precursors. Among the as-synthesized samples, the porous nanocage structure, synergistic effect of mixed metals, and unique phosphide composition endow nickel cobalt bimetallic phosphide (NiCo-P) nanocages with outstanding performance as a battery-type Faradaic electrode material for fast energy storage, with ultrahigh specific capacity of 894 C g-1 at 1 A g-1 and excellent rate capability, surpassing most of the reported metal compounds. Control experiments and theoretical calculations based on density functional theory reveal that the synergistic effect between Ni and Co in NiCo-P can greatly increase the OH- adsorption energy, while the hollow porous structure facilitates the fast mass/electron transport. The presented work not only provides a promising electrode material for fast energy storage, but also opens a new route toward structural and compositional design of electrode materials for energy storage and conversion.

Tuning Expanded Pores in Metal-Organic Frameworks for Selective Capture and Catalytic Conversion of Carbon Dioxide.

Three Co-based isostructural MOF-74-III materials with expanded pores are synthesized, with varied extent of fused benzene rings onto sidechain of same-length ligands to finely tune the pore sizes to 2.6, 2.4, and 2.2 nm. Gas sorption results for these highly mesoporous materials show that alternately arranged fused benzene rings on one side of the ligand could serve as extra anchoring sites for CO2 molecules with π-π interactions, conspicuously enhancing CO2 uptake and CO2 /CH4 and CO2 /N2 selectivity; while more steric hindrance effect towards open CoII sites were imposed by ligands flanked with fused benzene rings on both sides, compromising such extra-sites enhancement. In the catalytic conversion of CO2 with propylene oxide to form propylene carbonate, the as-synthesized MOF-74-III(Co) with desired properties of highly exposed and accessible open CoII centers, large mesopore apertures and multi-interactive sites, demonstrated higher catalytic activity compared with other two MOFs, with benzene rings fused to ligands hampering the functionality of CoII centers as Lewis acid sites. Our results highlight the viability of finely tuning the expanded pores of MOF-74 isostructure and the effect of fused benzene rings as functional groups onto selective CO2 capture and conversion.

Kinetic-Controlled Formation of Bimetallic Metal-Organic Framework Hybrid Structures.

Heterometallic metal-organic frameworks (MOFs) are constructed from two or more kinds of metal ions, while still remaining their original topologies. Due to distinct reaction kinetics during MOF formation, partial distribution of different metals within a single MOF crystal can lead to sophisticated heterogeneous nanostructures. Here, this study reports an investigation of reaction kinetics for different metal ions in a bimetallic MOF system, the ZIF-8/67 (M(2-mIM)2 , M = Zn for ZIF-8, and Co for ZIF-67, 2-mIM = 2-methylimidazole), by in situ optical method. Distinct kinetics of the two metals forming single-component MOFs are revealed, and when both Co and Zn ions are present in the starting solution, homogeneous distributions of the two metals are only achieved at high Co/Zn ratio, while at low Co/Zn ratio concentration gradient from Co-rich cores to Zn-rich shells is observed. Further, by adding the two metals in sequence, more sophisticated structures are achieved. Specifically, when Co2+ is added first, ZIF-67@ZIF-8/67 core-shell nanocrystals are achieved with tunable core/shell thickness ratio depending on the time intervals; while when Zn2+ is added first, only agglomerates of irregular shape form due to the weak nucleation ability of Zn2+ .