Realistic operation of two residential cordwood-fired outdoor hydronic heater appliances-Part 2: Particle number and size.

The use of wood as a fuel for home heating is a concern from an environmental health and safety perspective as biomass combustion appliances emit high concentrations of particulate matter. Wood burning significantly contributes to wintertime particulate matter concentrations in many states in the northern United States. Of particular concern are outdoor wood-fired hydronic heaters. These devices are concerning as they tend to have very large combustion chambers and typical use patterns can result in long periods of low output, which result in an increased particulate matter emission rate relative to high heat output operating conditions. In this study, the performance of two hydronic heaters operating under different combustion conditions, including four different heat output categories approximately corresponding to categories I-IV denoted in Environmental Protection Agency Method 28 Outdoor Wood-fired Hydronic Heaters, and during start-up and reloading events were investigated. Measurements of flue gas particulate number concentration and size for particles with aerodynamic diameters between 0.006 and 10 µm were made using a dilution sampling system. The measured particle number concentration in the flue gas was between 0.71 and 420 million particles per cubic centimeter and was dependent on fuel loading and heat output. For each hydronic heater tested, the highest average particle concentration was found at the beginning of each test during the cold-start condition. Additionally, the majority of the particles had aerodynamic diameters less than 0.100 µm (particles of this size made up between 64% and 97% of all particles) and less than 1% of all particles had aerodynamic diameters greater than 1 µm for all phases. For particles in the accumulation mode, between 0.100 and 1 µm, the mean particle diameter was dependent on fuel loading and heat output.Implications: In this work, we provide information on the particle number concentration and particle size of emissions from outdoor cord- wood-fired hydronic heaters. Wood-fired hydronic heater data is sparsely available compared to wood stove data. Thus, additional data from this source help to inform the work of modelers and policy makers interested in hydronic heaters. The test method used in this work is also novel, as it is more inclusive of real-world use cases than the current certification method. Our data helps to validate the test method and allows for comparisons between real-world use case scenarios, and idealized test cases.

Characterization of in-stack particulate emissions from residential wood hydronic heater appliances under different combustion conditions.

In the current work, we provide measurements of size-resolved particle number concentration (PNC), particle mass concentration (PMC), lung-deposited surface area (LDSA), and black carbon (BC) concentration for three biomass fired hydronic heaters during operation in four different combustion conditions. The appliances include one woodchip-fueled hydronic heater and two outdoor cordwood-fueled hydronic heaters. The operating conditions included startup, low output, high output, and burnout. Measurements were made using a custom dilution sampling system and a suite of commercially available, time-resolved, ambient aerosol measurement instrumentation. The PNC, as measured using an Dekati Electrical Low Pressure Impactor+ (ELPI), had operating condition mean values ranging between 4.1 and 52 million particles per cubic centimeter (#/cm3). The highest reported PNC occurred during the startup condition in all cases. Calculating the particle size distribution measured across each operating phase for the same instrument gave geometric mean diameters (dg) in the range of 0.080-0.256 µm. The largest dg per appliance was nearly always attributable to the startup condition (for hydronic heater 1, startup dg ranked second).We did not observe the same trends when we transformed the ELPI PNC to PMC and particle surface area concentration estimates across operating conditions, suggesting PNC and dg are highly variable. Furthermore, simultaneous measurements of PNC, PMC, and PSAC using instrumentation with different working principles gave varying results, potentially suggesting that particles of different composition and morphology are produced under different combustion conditions.Implications: In this work we compare the results from testing of 3 biomass fired hydronic heaters including one chip-fired appliance and two cordwood-fired appliances. The emissions from these appliances were made across four operating conditions and using three different non-regulatory emissions metrics. This work: describes the difference between chip and cordwood fired units and the effect of operating condition on emissions across the three emissions metrics.

Realistic operation of two residential cordwood-fired outdoor hydronic heater appliances-Part 3: Optical properties of black and brown carbon emissions.

Residential biomass combustion is a source of carbonaceous aerosol. Inefficient combustion, particularly of solid fuels produces large quantities of black and brown carbon (BC and BrC). These particle types are important as they have noted effects on climate forcing and human health. One method of measuring these quantities is by measurement of aerosol light-absorption and scattering, which can be performed using an aethalometer and nephelometer, respectively. These instruments are widely deployed in the study of ambient air and are frequently used in air quality modeling and source apportionment studies. In this study, we will describe (1) a method for measuring primary BC and BrC emissions from two residential log-fired wood hydronic heaters and (2) the BC and BrC emission from these devices over a wide range of operating conditions, such as cold-starts, warm-starts, four different levels of output ranging from 15% to 100% maximum rated output, and periods of repeated cycling. The range in flue-gas BC concentrations, measured using an aethalometer at the 880 nanometer (nm) wavelength, were between 5.09 × 102 and 2.24 × 104 micrograms per cubic meter (µg/m3) while the scattering coefficient of the flue-gas, measured by a nephelometer at 880 nm, ranged between 2.20 × 103 and 8.56 × 105 inverse megameters (Mm-1). The BrC concentrations, measured using the 370 nm wavelength of an aethalometer, were between 9.10 × 101 and 3.56 × 104 µg/m3. The calculated Angstrom Absorption Exponent (AAE) of the flue-gas aerosol ranged between 1.54 and 3.63. Performing a comparison between the measured BC concentration and an external particulate matter (PM) concentration showed that overall BC makes up roughly a quarter of the PM emitted by either of the two appliances. Further for both appliances, the cold-start and the test phase immediately following it had the highest BC and BrC concentrations, the highest measured scattering coefficient, as well as a low AAE.Implications: In this work we provide information on the black and brown carbon emissions from outdoor cordwood-fired hydronic heaters. Aethalometer based black carbon measurements are common in atmospheric science, but are uncommonly used in laboratory studies. This work helps to bridge that gap. This data helps to inform the work of modelers and policy makers interested in hydronic heaters and source apportioning biomass combustion emissions.