Controlled Surface Modification of Cobalt Phosphide with Sulfur Tunes Hydrogenation Catalysis.

Transition metal phosphides have shown promise as catalysts for water splitting and hydrotreating, especially when a small amount of sulfur is incorporated into the phosphides. However, the effect of sulfur on catalysis is not well understood. In part, this is because conventional preparation methods of sulfur-doped transition metal phosphides lead to sulfur both inside and at the surface of the material. Here, we present an alternative method of modifying cobalt phosphide (CoP) with sulfur using molecular S-transfer reagents, namely, phosphine sulfides (SPR3). SPR3 added sulfur to the surface of CoP and using a series of SPR3 reagents having different P═S bond strengths enabled control over the amount and type of sulfur transferred. Our results show that there is a distribution of different sulfur sites possible on the CoP surface with S-binding strengths in the range of 69 to 84 kcal/mol. This provides fundamental information on how sulfur binds to an amorphous CoP surface and provides a basis to assess how number and type of sulfur on CoP influences catalysis. For the catalytic hydrogenation of cinnamaldehyde, intermediate amounts of sulfur with intermediate binding strengths at the surface of CoP were optimal. With some but not too much sulfur, CoP exhibited a higher hydrogenation productivity and a decreased formation of secondary reaction products. Our work provides important insight into the S-effect on the catalysis by transition metal phosphides and opens new avenues for catalyst design.

The influence of alkyl chains on the performance of DSCs employing iron(II) N-heterocyclic carbene sensitizers.

The photovoltaic performances of DSCs employing two new iron(II) N-heterocyclic carbene (NHC) sensitizers are presented. The presence of n-butyl side chains had a significant impact on DSC performace. The improvement in DSC performance up to 0.93-0.95% was observed for a new heteroleptic sensitizer bearing one carboxylic acid anchoring group. The photovoltaic performance was remarkably affected by sensitization time and by a presence/absence of coadsorbent on the semiconductor surface. The highest photoconversion efficiencies (PCE) were achieved for DSCs sensitized over 17.5 hours without addition of coadsorbents. However, for a shorter dipping time of 4 hours, the presence of chenodeoxycholic acid improved the PCE from 0.46% (no coadsorbents) to 0.74%, respectively. The performance of DSCs based on a new homoleptic complex bearing two n-butyl side chains and a carboxylic acid anchor on each NHC-ligand was improved from 0.05 to 0.29% via changes in dye-bath concentration and sensitization time. The changes in the dye load on the semiconductor surface depending on the sensitization conditions were confirmed using solid-state UV-Vis spectroscopy and thermogravimetric analysis. Electrochemical impedance spectroscopy was used to gain information about the processes occurring at the different interfaces in the DSCs. The impedance response was strongly affected by the immersion time of the photoanodes in the dye-bath solutions. In the case of the homoleptic iron(II) complex, a Gerischer impedance was observed after 17.5 hours immersion. Shorter dipping times resulted in a decrease in the resistance in the system. For the heteroleptic complex, values of the chemical capacitance and electron lifetime were affected by the immersion time. However, the diffusion length was independent of sensitization conditions.

There Is a Future for N-Heterocyclic Carbene Iron(II) Dyes in Dye-Sensitized Solar Cells: Improving Performance through Changes in the Electrolyte.

By systematic tuning of the components of the electrolyte, the performances of dye-sensitized solar cells (DSCs) with an N-heterocyclic carbene iron(II) dye have been significantly improved. The beneficial effects of an increased Li+ ion concentration in the electrolyte lead to photoconversion efficiencies (PCEs) up to 0.66% for fully masked cells (representing 11.8% relative to 100% set for N719) and an external quantum efficiency maximum (EQEmax) up to approximately 25% due to an increased short-circuit current density (JSC). A study of the effects of varying the length of the alkyl chain in 1-alkyl-3-methylimidazolium iodide ionic liquids (ILs) shows that a longer chain results in an increase in JSC with an overall efficiency up to 0.61% (10.9% relative to N719 set at 100%) on going from n-methyl to n-butyl chain, although an n-hexyl chain leads to no further gain in PCE. The results of electrochemical impedance spectroscopy (EIS) support the trends in JSC and open-circuit voltage (VOC) parameters. A change in the counterion from I- to [BF4]- for 1-propyl-3-methylimidazolium iodide ionic liquid leads to DSCs with a remarkably high JSC value for an N-heterocyclic carbene iron(II) dye of 4.90 mA cm-2, but a low VOC of 244 mV. Our investigations have shown that an increased concentration of Li+ in combination with an optimized alkyl chain length in the 1-alkyl-3-methylimidazolium iodide IL in the electrolyte leads to iron(II)-sensitized DSC performances comparable with those of containing some copper(I)-based dyes.