Investigation of non-precious metal cathode catalysts for direct borohydride fuel cells.

Borohydride crossover in anion exchange membrane (AEM) based direct borohydride fuel cells (DBFCs) impairs their performance and induces cathode catalyst poisoning. This study evaluates three non-precious metal catalysts, namely LaMn0.5Co0.5O3 (LMCO) perovskite, MnCo2O4 (MCS) spinel, and Fe-N-C, for their application as cathode catalysts in DBFCs. The rotating disk electrode (RDE) testing shows significant borohydride tolerance of MCS. Moreover, MCS has exhibited exceptional stability in accelerated durability tests (ADTs), with a minimal reduction of 10 mV in half-wave potential. DFT calculations further reveal that these catalysts predominantly adsorb over , unlike commercial Pt/C which preferentially adsorbs . In DBFCs, MCS can deliver a peak power density of 1.5 W cm-2, and a 3% voltage loss after a 5 hours durability test. In contrast, LMCO and Fe-N-C have exhibited significantly lower peak power density and stability. The analysis of the TEM, XRD, and XPS results before and after the single-cell stability tests suggests that the diminished stability of LMCO and Fe-N-C catalysts is due to catalyst detachment from carbon supports, resulting from the nanoparticle aggregation during the high-temperature preparation process. Such findings suggest that MCS can effectively mitigate the fuel crossover challenge inherent in DBFCs, thus enhancing its viability for practical application.

Oxygen-deficient TiO2-x interlayer enabling Li-rich Mn-based layered oxide cathodes with enhanced reversible capacity and cyclability.

The unique anion redox mechanism of Li-rich Mn-based layered oxide (LMLO) cathodes endows them with a higher specific capacity compared with conventional cathodes. However, the irreversible anion redox reactions can cause structural degradation and sluggish electrochemical kinetics in the cathode, resulting in a poor electrochemical performance in the batteries. Thus, to address these issues, a single-sided conductive oxygen-deficient TiO2-x interlayer was applied on a commercial Celgard separator as a coating layer towards the LMLO cathode. After coating TiO2-x, the initial coulombic efficiency (ICE) of the cathode increased from 92.1% to 95.8%, the capacity retention improved from 84.2% to 91.7% after 100 cycles, and the rate performance of the cathode was significantly enhanced from 91.3 mA h g-1 to 203.9 mA h g-1 at 5C. Operando differential electrochemical mass spectroscopy (DEMS) showed that the coating layer could restrain the release of oxygen in the battery, especially from the initial formation process. The X-ray photoelectron spectroscopy (XPS) results demonstrated that the favorable oxygen absorption by the TiO2-x interlayer benefitted the suppression of side reactions and cathode structural evolution and favored the formation of a uniform cathode-electrolyte interphase on the LMLO cathode. This work provides an alternative path to address the issue of oxygen release in LMLO cathodes.

Mitigation of Oxygen Evolution and Phase Transition of Li-Rich Mn-Based Layered Oxide Cathodes by Coating with Oxygen-Deficient Perovskite Compounds.

Li-rich Mn-based layered oxide cathodes with a high discharge capacity hold great promise for high energy density lithium-ion batteries. However, application is hampered by voltage and capacity decay and gas evolution during cycling due to interfacial side reactions. Here, we report coating by oxygen-deficient perovskite La0.9Sr0.1CoO3 using the Pechini process. X-ray photoelectron spectroscopy and scanning transmission electron microscopy both exhibit a uniform coating layer with a high oxygen vacancy concentration. The coating effectively mitigates the first cycle irreversible capacity loss and voltage decay while increasing cyclability. Optimized coating improves capacity retention from 55.6% to 84.8% after 400 cycles at 2 C. Operando differential electrochemical mass spectroscopy shows that such a coating can significantly mitigate the release of oxygen and carbon dioxide. Electrochemical impedance spectroscopy and post-mortem analysis indicate that the coating layer forms a stable interface and restricts structure evolution and cation mixing during cycling, conferring these cathode materials with better cycling and voltage stability. The perovskite can be applied to other cathodes with high voltage and capacity to suppress interfacial side reactions toward developing stable high energy density batteries.

Single-Crystalline Cathodes for Advanced Li-Ion Batteries: Progress and Challenges.

Single-crystalline cathodes are the most promising candidates for high-energy-density lithium-ion batteries (LIBs). Compared to their polycrystalline counterparts, single-crystalline cathodes have advantages over liquid-electrolyte-based LIBs in terms of cycle life, structural stability, thermal stability, safety, and storage but also have a potential application in solid-state LIBs. In this review, the development history and recent progress of single-crystalline cathodes are reviewed, focusing on properties, synthesis, challenges, solutions, and characterization. Synthesis of single-crystalline cathodes usually involves preparing precursors and subsequent calcination, which are summarized in the details. In the following sections, the development issues of single-crystalline cathodes, including kinetic limitations, interfacial side reactions, safety issues, reversible planar gliding and micro-cracking, and particle size distribution and agglomeration, are systematically analyzed, followed by current solutions and characterization techniques. Finally, this review is concluded with proposed research thrusts for the future development of single-crystalline cathodes.

A Review of the Transition Region of Membrane Electrode Assembly of Proton Exchange Membrane Fuel Cells: Design, Degradation, and Mitigation.

As the core component of a proton exchange fuel cell (PEMFC), a membrane electrode assembly (MEA) consists of function region (active area), structure region, and transition region. Situated between the function and structure regions, the transition region influences the reliability and durability of the MEA. The degradation of the electrolyte membrane in this region can be induced by mechanical stress and chemical aggression. Therefore, prudent design, reliable and robust structure of the transition region can greatly help avoid early failure of MEAs. This review begins with the summarization of current structural concepts of MEAs, focusing on the transition region structures. It can be seen that aiming at better repeatability and robustness, partly or total integration of the materials in the transition region is becoming a development trend. Next the degradation problem at the transition region is introduced, which can be attributed to the hygro-thermal environment, free radical aggression, air pressure shock, and seal material decomposition. Finally, the mitigation approaches for the deterioration at this region are summarized, with a principle of avoiding the exposure of the membrane at the edge of the catalyst-coated membrane (CCM). Besides, durability test methods of the transition region are included in this review, among which temperature and humidity cycling are frequently used.

High-Performance Zinc-Air Batteries Based on Bifunctional Hierarchically Porous Nitrogen-Doped Carbon.

Active and durable bifunctional electrocatalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) on the cathode are required for high-performance rechargeable metal-air batteries. Herein, the synthesis of hierarchically porous nitrogen-doped carbon (HPNC) with bifunctional oxygen electrocatalysis for Zn-air batteries is reported. The HPNC catalyst possesses a large surface area of 1459 m2 g-1 and exhibits superior electrocatalytic activity toward ORR and OER simultaneously with a low OER/ORR overpotential of 0.62 V, taking the difference between the potential at 10 mA cm-2 for OER and half-wave potential for ORR in 0.1 m KOH. Adopting HPNC as the air cathode, primary and rechargeable Zn-air batteries are fabricated. The primary batteries demonstrate a high open-circuit potential of 1.616 V, a specific capacity of 782.7 mAh gZn -1 and a superb peak power density of 201 mW cm-2 . The rechargeable batteries can be cycled stably for over 360 cycles or 120 h at the current density of 5 mA cm-2 . As elucidated by density functional theory, N-doping is preferred on defective sites with pentagon configuration and on the edge in the form of pyridinic-N-type. The high content of these two motifs in HPNC leads to the superior ORR and OER activities, respectively.

Synthesis of Anti-poisoning Spinel Mn-Co-C as Cathode Catalysts for Low-Temperature Anion Exchange Membrane Direct Ammonia Fuel Cells.

Low-temperature anion exchange membrane direct ammonia fuel cells (AEM-DAFCs) have emerged as a potential power source for transportation applications with the recognition that liquid ammonia is a carbon-free hydrogen carrier and facilitates storage, refill, and distribution. However, ammonia crossover from the cell anode to cathode can decrease the fuel efficiency, drop the voltage, and poison the cathode catalysts. In this work, the Mn-Co spinel on three different carbon supports [BP2000, Vulcan XC-72R, and multiwalled carbon nanotubes (MWCNTs)] has been successfully synthesized and demonstrated a high oxygen reduction reaction (ORR) activity with good ammonia tolerance. The structure and composition of the obtained Mn-Co-C catalysts were characterized by high-angle annular dark-field scanning transmission electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. All three catalysts exhibit superb ammonia tolerance, and Mn-Co-BP2000 demonstrates the highest ORR activity, even better than the commercial Pt-C in the presence of ammonia. When paired with the commercial PtIr-C anode, the Mn-Co-BP2000 cathode improved the peak power density of single cells from 100.1 mW cm-2 for the Pt-C cathode to 128.2 mW cm-2 under a 2 bar backpressure in both electrodes at 80 °C. All the results have manifested that Mn-Co-BP2000 is a good cathode catalyst for low-temperature AEM-DAFCs.

From bulk to interface: electrochemical phenomena and mechanism studies in batteries via electrochemical quartz crystal microbalance.

Understanding the bulk and interfacial behaviors during the operation of batteries (e.g., Li-ion, Na-ion, Li-O2 batteries, etc.) is of great significance for the continuing improvement of the performance. Electrochemical quartz crystal microbalance (EQCM) is a powerful tool to this end, as it enables in situ investigation into various phenomena, including ion insertion/deinsertion within electrodes, solid nucleation from the electrolyte, interphasial formation/evolution and solid-liquid coordination. As such, EQCM analysis helps to decipher the underlying mechanisms both in the bulk and at the interface. This tutorial review will present the recent progress in mechanistic studies of batteries achieved by the EQCM technology. The fundamentals and unique capability of EQCM are first discussed and compared with other techniques, and then the combination of EQCM with other in situ techniques is also covered. In addition, the recent studies utilizing EQCM technologies in revealing phenomena and mechanisms of various batteries are reviewed. Perspectives regarding the future application of EQCM in battery studies are given at the end.

Preparation of a Graphitized-Carbon-Supported PtNi Octahedral Catalyst and Application in a Proton-Exchange Membrane Fuel Cell.

In this work, PtNi/GC octahedral nanocrystal catalysts are prepared using graphitized carbon (GC) to solve the problems of cathode catalysts in catalytic performance and proton-exchange membrane fuel cell application. The as-prepared supported catalysts exhibit well-crystallized octahedral morphologies and graphite layer structures with high corrosion resistance. Their mass activities and specific activities are 5 and 7 times higher than those of the commercial Pt/C. The sample with the best performance shows the cell voltage at 1000 mA cm-2 of 0.672 V and maximum power density of 817.6 mW cm-2 in the single-cell test, which are increased by 23 mV and 13.2 mW cm-2 compared to the control. Especially after a high potential test, the above two parameters of this sample are reduced by only 5.6 and 8.4%, which are significantly lower than the attenuation of the control fabricated using Vulcan XC-72 carbon black. The work reveals that the GC-supported PtNi octahedral catalysts can give better consideration to the improvement of electrochemical and single-cell performances.

Thermally Robust Porous Bimetallic (Ni xPt1- x) Alloy Mesocrystals within Carbon Framework: High-Performance Catalysts for Oxygen Reduction and Hydrogenation Reactions.

Thermally stable porous bimetallic (Ni xPt1- x) alloy mesocrystals within a carbon framework are produced via an aerosol-assisted process for high-performance catalysts for the oxygen reduction reaction (ORR) and hydrogenation. The porous Ni xPt1- x alloy has a robust composite of alloy nanoparticles with an adjustable composition and a porous carbon skeleton. Porous Ni xPt1- x alloys exhibit high thermal stability, retaining their crystalline structure and morphology at 550 °C for 6 h, as observed in thermal treatment tests under various conditions (time, temperature, and atmosphere). The porous Ni xPt1- x alloy as a catalyst for the hydrogenation of propylene has high conversion efficiency (>80%) and low activation energy ( Ea < 20 kJ/mol) at ≥80 °C through the suitable control of the element composition and a pore structure. As a catalyst for the ORR, the catalytic activity of the porous Ni xPt1- x alloy is superior to that of conventional Pt/C (0.115 mA) (0.853 mA/cmPt2 at 0.9 V/cmPt2). This is attributed to the homogeneous alloying of the metal components (Ni and Pt) and the increased accessibility of the reactants to the catalyst, resulting from the unique morphology of the porous Ni xPt1- x alloy, i.e., hierarchical structure with high porosity.

High-quality mesoporous graphene particles as high-energy and fast-charging anodes for lithium-ion batteries.

The application of graphene for electrochemical energy storage has received tremendous attention; however, challenges remain in synthesis and other aspects. Here we report the synthesis of high-quality, nitrogen-doped, mesoporous graphene particles through chemical vapor deposition with magnesium-oxide particles as the catalyst and template. Such particles possess excellent structural and electrochemical stability, electronic and ionic conductivity, enabling their use as high-performance anodes with high reversible capacity, outstanding rate performance (e.g., 1,138 mA h g-1 at 0.2 C or 440 mA h g-1 at 60 C with a mass loading of 1 mg cm-2), and excellent cycling stability (e.g., >99% capacity retention for 500 cycles at 2 C with a mass loading of 1 mg cm-2). Interestingly, thick electrodes could be fabricated with high areal capacity and current density (e.g., 6.1 mA h cm-2 at 0.9 mA cm-2), providing an intriguing class of materials for lithium-ion batteries with high energy and power performance.

Creating Lithium-Ion Electrolytes with Biomimetic Ionic Channels in Metal-Organic Frameworks.

Solid-state electrolytes are the key to the development of lithium-based batteries with dramatically improved energy density and safety. Inspired by ionic channels in biological systems, a novel class of pseudo solid-state electrolytes with biomimetic ionic channels is reported herein. This is achieved by complexing the anions of an electrolyte to the open metal sites of metal-organic frameworks (MOFs), which transforms the MOF scaffolds into ionic-channel analogs with lithium-ion conduction and low activation energy. This work suggests the emergence of a new class of pseudo solid-state lithium-ion conducting electrolytes.

Regenerative Polysulfide-Scavenging Layers Enabling Lithium-Sulfur Batteries with High Energy Density and Prolonged Cycling Life.

Lithium-sulfur batteries, notable for high theoretical energy density, environmental benignity, and low cost, hold great potential for next-generation energy storage. Polysulfides, the intermediates generated during cycling, may shuttle between electrodes, compromising the energy density and cycling life. We report herein a class of regenerative polysulfide-scavenging layers (RSL), which effectively immobilize and regenerate polysulfides, especially for electrodes with high sulfur loadings (e.g., 6 mg cm-2). The resulting cells exhibit high gravimetric energy density of 365 Wh kg-1, initial areal capacity of 7.94 mAh cm-2, low self-discharge rate of 2.45% after resting for 3 days, and dramatically prolonged cycling life. Such blocking effects have been thoroughly investigated and correlated with the work functions of the oxides as well as their bond energies with polysulfides. This work offers not only a class of RSL to mitigate shuttling effect but also a quantified design framework for advanced lithium-sulfur batteries.

Electrochemical Doping of Halide Perovskites with Ion Intercalation.

Halide perovskites have recently been investigated for various solution-processed optoelectronic devices. The majority of studies have focused on using intrinsic halide perovskites, and the intentional incoporation of dopants has not been well explored. In this work, we discovered that small alkali ions, including lithium and sodium ions, could be electrochemically intercalated into a variety of halide and pseudohalide perovskites. The ion intercalation caused a lattice expansion of the perovskite crystals and resulted in an n-type doping of the perovskites. Such electrochemical doping improved the conductivity and changed the color of the perovskites, leading to an electrochromism with more than 40% reduction of transmittance in the 450-850 nm wavelength range. The doped perovskites exhibited improved electron injection efficiency into the pristine perovskite crystals, resulting in bright light-emitting diodes with a low turn-on voltage.

One-Step Synthesis of Microporous Carbon Monoliths Derived from Biomass with High Nitrogen Doping Content for Highly Selective CO2 Capture.

The one-step synthesis method of nitrogen doped microporous carbon monoliths derived from biomass with high-efficiency is developed using a novel ammonia (NH3)-assisted activation process, where NH3 serves as both activating agent and nitrogen source. Both pore forming and nitrogen doping simultaneously proceed during the process, obviously superior to conventional chemical activation. The as-prepared nitrogen-doped active carbons exhibit rich micropores with high surface area and high nitrogen content. Synergetic effects of its high surface area, microporous structure and high nitrogen content, especially rich nitrogen-containing groups for effective CO2 capture (i.e., phenyl amine and pyridine-nitrogen) lead to superior CO2/N2 selectivity up to 82, which is the highest among known nanoporous carbons. In addition, the resulting nitrogen-doped active carbons can be easily regenerated under mild conditions. Considering the outstanding CO2 capture performance, low production cost, simple synthesis procedure and easy scalability, the resulting nitrogen-doped microporous carbon monoliths are promising candidates for selective capture of CO2 in industrial applications.

Inward lithium-ion breathing of hierarchically porous silicon anodes.

Silicon has been identified as a highly promising anode for next-generation lithium-ion batteries (LIBs). The key challenge for Si anodes is large volume change during the lithiation/delithiation cycle that results in chemomechanical degradation and subsequent rapid capacity fading. Here we report a novel fabrication method for hierarchically porous Si nanospheres (hp-SiNSs), which consist of a porous shell and a hollow core. On charge/discharge cycling, the hp-SiNSs accommodate the volume change through reversible inward Li breathing with negligible particle-level outward expansion. Our mechanics analysis revealed that such inward expansion is enabled by the much stiffer lithiated layer than the unlithiated porous layer. LIBs assembled with the hp-SiNSs exhibit high capacity, high power and long cycle life, which is superior to the current commercial Si-based anode materials. The low-cost synthesis approach provides a new avenue for the rational design of hierarchically porous structures with unique materials properties.

Mesoporous metal and metal alloy particles synthesized by aerosol-assisted confined growth of nanocrystals.

From droplets to "spheres": A platform technology enables the rapid and continuous synthesis of mesoporous metal and metal alloy particles (see picture). The confined growth of nanocrystals in aerosol droplets leads to the formation of these particles with defined composition.

High-performance sodium-ion pseudocapacitors based on hierarchically porous nanowire composites.

Electrical energy storage plays an increasingly important role in modern society. Current energy storage methods are highly dependent on lithium-ion energy storage devices, and the expanded use of these technologies is likely to affect existing lithium reserves. The abundance of sodium makes Na-ion-based devices very attractive as an alternative, sustainable energy storage system. However, electrodes based on transition-metal oxides often show slow kinetics and poor cycling stability, limiting their use as Na-ion-based energy storage devices. The present paper details a new direction for electrode architectures for Na-ion storage. Using a simple hydrothermal process, we synthesized interpenetrating porous networks consisting of layer-structured V(2)O(5) nanowires and carbon nanotubes (CNTs). This type of architecture provides facile sodium insertion/extraction and fast electron transfer, enabling the fabrication of high-performance Na-ion pseudocapacitors with an organic electrolyte. Hybrid asymmetric capacitors incorporating the V(2)O(5)/CNT nanowire composites as the anode operated at a maximum voltage of 2.8 V and delivered a maximum energy of ∼40 Wh kg(-1), which is comparable to Li-ion-based asymmetric capacitors. The availability of capacitive storage based on Na-ion systems is an attractive, cost-effective alternative to Li-ion systems.

Polymer-graphene nanocomposites as ultrafast-charge and -discharge cathodes for rechargeable lithium batteries.

Electroactive polymers are a new generation of "green" cathode materials for rechargeable lithium batteries. We have developed nanocomposites combining graphene with two promising polymer cathode materials, poly(anthraquinonyl sulfide) and polyimide, to improve their high-rate performance. The polymer-graphene nanocomposites were synthesized through a simple in situ polymerization in the presence of graphene sheets. The highly dispersed graphene sheets in the nanocomposite drastically enhanced the electronic conductivity and allowed the electrochemical activity of the polymer cathode to be efficiently utilized. This allows for ultrafast charging and discharging; the composite can deliver more than 100 mAh/g within just a few seconds.

Alloyed semiconductor nanocrystals with broad tunable band gaps.

Nearly monodisperse alloyed (CuInS2)x(ZnS)1-x nanocrystals with cubic and hexagonal phases were successfully synthesized for the first time, and the band gaps of these alloyed nanocrystals can be tuned in the broad range of 1.5 to 3.7 eV by changing the ratio of CuInS2 to ZnS.