Polyvinyl Alcohol/Graphene Oxide Interlayer for Enhancing Adhesive Performance of HA Coating on C/C Composites Prepared by Hydrothermal Electrodeposition/Hydrothermal Treatment.

Hydroxyapatite (HA) coatings directly deposited by hydrothermal electrochemical technology (HET) onto carbon/carbon (C/C) composites exhibited a catastrophic failure occurring at the interface of the HA and C/C. To overcome this problem, a polyvinyl alcohol (PVA)/graphene oxide (GO) interlayer (P/G interlayer) was applied on the (NH4)2S2O8-pretreated C/C substrate (named P/G-C/C) by using a dipping method. Subsequently, a calcium phosphate coating was deposited on P/G-C/C, shortened as M-P/G-C/C, by HET, and then converted into HA coating (abbreviated as HA-P/G-C/C) through posthydrothermal treatment. For comparison, HA coating was prepared onto C/C without a P/G interlayer through the same process, which was denoted as HA-C/C. The composition, microstructure, and morphology of the samples were characterized by X-ray diffractometry (XRD), energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), Raman spectra, Fourier transform infrared (FTIR), and X-ray photoelectron spectroscopy (XPS). The adhesive performance of the coatings on C/C was measured by a scratch test. Finally, an in vitro bioactivity of the coatings was evaluated in a simulated body fluid solution at 37 °C. Results showed no apparent differences in the morphology and phase of the posttreated coatings, both of which are composed of a dense structure containing needle-like HA crystals. However, the HA-P/G-C/C sample possessed a higher Ca/P ratio and denser interface, thereby exhibiting higher adhesive performance and better bioactivity. The adhesive strength of the HA-P/G coating was observed at a critical load of 41.04 N, which increased by 29.3% relative to the HA coating. Moreover, the failure site was on the HA-P/G coating rather than at the interface. The enhanced adhesive performance was ascribed to the PVA/GO-repairing pits on C/C and PVA and GO toughening effects on the HA coating. In vitro and in vivo tests revealed no statistical significance for the two HA-coated C/C samples, although the HA-P/G coating exhibited better bioactivity, inducing the growth of bonelike apatite than the HA coating.

MgCl2 promotes mouse mesenchymal stem cell osteogenic differentiation by activating the p38/Osx/Runx2 signaling pathway.

Magnesium, an important inorganic mineral component in bones, enhances osteoblast adhesion and osteogenic gene expression. Mg2+­containing hydroxyapatite promotes mouse mesenchymal stem cell (MMSC) osteogenic differentiation. In the present study, MMSCs were cultured in media containing different concentrations of MgCl2 (0 and 20 mM) for different time periods. Western blotting and reverse transcription­quantitative PCR were performed to determine the expression levels of phosphorylated (p)­p38 mitogen­activated protein kinase (MAPK), the osteoblast­specific transcription factor Osterix (Osx), runt­related transcription factor 2 (Runx2), and p38 downstream genes, such as 27 kDa heat shock protein (hsp27), activating transcription factor 4 (Atf4), myocyte enhancer factor 2C (Mef2c) and CCAAT/enhancer­binding protein homologous protein (Ddit3). The facilitatory effect of MgCl2 on MMSC osteogenic differentiation was assessed via Alizarin Red staining. The results suggested that MgCl2 increased p38 phosphorylation compared with the control group. Downstream genes of the p38 signaling pathway, including Osx and Runx2, as well as several osteogenesis­associated downstream target genes, including Hsp27, Atf4, Ddit3 and Mef2c, were significantly upregulated in the Mg2+­treated group compared with the control group. The increased osteogenic differentiation in the Mg2+­treated group was significantly attenuated in MMSCs treated with SB203580, a specific inhibitor of the p38 signaling pathway. The results suggested that appropriate concentrations of MgCl2 promoted MMSC osteogenic differentiation via regulation of the p38/Osx/Runx2 signaling pathway.

Enhanced Visible Light Driven Photocatalytic Behavior of BiFeO3/Reduced Graphene Oxide Composites.

BiFeO3/Reduced Graphene Oxide (BFO/RGO) composites have been fabricated by a simple hydrothermal method. The X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman, and X-ray photoelectron spectroscopy (XPS) analysis reveal that graphene oxide was reduced in hydrothermal process and BFO/RGO composites were successfully synthesized. UV-visible absorption and photoluminescence properties show that the introduction of RGO can effectively reduce the recombination of photogenerated electron and hole pairs. Compared to the pristine BFO, the photocatalytic performance of BiFeO3 Graphene Oxide (BGO) composites is enhanced for the degradation of Methylene blue (MB) solution under visible light irradiation, and the result shows that the optimal amount of Graphene Oxide (GO) in the composites is 60 mg (BGO60). The excellent photocatalytic performance is mainly ascribed to improved light absorption, increased reactive sites, and the low recombination rate of electron-hole pairs. This work can provide more insights into designing advanced photocatalysts for wastewater treatment and environmental protection.

Strong bonding strength between HA and (NH4)2S2O8-treated carbon/carbon composite by hydrothermal treatment and induction heating.

Carbon/carbon composite with hydroxyapatite (HA) coating is an attractive material in the dental and orthopedic fields, but the reported bonding strength between them was very poor. In this study, a compact crystalline HA coating on (NH(4))(2)S(2)O(8)-treated C/C substrate about 10 microm in width was obtained by hydrothermal treatment and induction heating. The microstructure, composition and morphologies of the as-prepared coatings were identified by X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. A strong shear strength averaging 74.2 MPa between C/C substrate and HA was achieved and adhesion failures were observed more frequently than cohesion failures. The coating adhesion measured using a scratch test was 23 N and the reasons for this are discussed.