Changes of characteristics and disinfection by-products formation potential of intracellular organic matter with different molecular weight in metalimnetic oxygen minimum.

Metalimnetic oxygen minimum (MOM) occurs in reservoirs or lakes due to stratification and algal blooms, which has low dissolved oxygen (DO) levels and leads to the deterioration of water quality. The transformation mechanism and the impact on the water quality of intracellular organic matter (IOM) derived from algae are poorly understood under MOM conditions. In this study, IOM extracted by Microcystis aeruginosa was divided into five components according to molecular weight (MW), and the changes of characteristics and correlated disinfection by-products formation potential (DBPFP) were analyzed and compared under MOM conditions. The removal efficiency of dissolved organic carbon (DOC) in the <5 kDa fraction (66.6%) was higher than that in the >100 kDa fraction (41.8%) after a 14-day incubation under MOM conditions. The same tendency also occurred in Fmax and DBPFP. The decrease in Fmax was mainly due to the decline in tryptophan-like and tyrosine-like for all IOM fractions. The diversity of microorganisms degrading the MW > 100 kDa fraction was lower than others. Besides low MW fractions, these findings indicated that more attention should be paid to high MW fractions which were resistant to biodegradation under MOM conditions during water treatment.

The aggregation characteristics of Aspergillus spores under various conditions and the impact on LPUV inactivation: Comparisons with chlorine-based disinfection.

Aggregation is the primary step prior to fungal biofilm development. Understanding the attributes of aggregation is of great significance to better control the emergence of waterborne fungi. In this study, the aggregation of Aspergills spores (A. flavus and A. fumigatus) under various salt, culture medium, and humic acid (HA) conditions was investigated for the first time, and the inactivation via low-pressure ultraviolet (LPUV) upon aggregated Aspergillus spores was also presented. The aggregation efficiency and size of aggregates increased over time and at low salt (NaCl and CaCl2) concentration (10 mM) while decreasing with the continuous increase of salt concentration (100 and 200 mM). Increasing the concentration of culture medium and HA promoted the aggregation of fungal spores. Spores became hydrated, swelled, and secreted more viscous substances during the growth period, which accelerated the aggregation process. Results also suggested that fungal spores aggregated more easily in actual water, posing a high risk of biohazard in real-life scenarios. Inactivation efficiency by LPUV decreased with higher aggregation degrees due to the protection from the damaged spores on the outer layer and the shielding of pigments in the cell wall. Compared to chlorine-based disinfection, the aggregation resulted in the extension of shoulder length yet neglectable change of inactivation rate constant under LPUV treatment. Further investigation of cell membrane integrity and intracellular reactive oxygen species was conducted to elucidate the difference in mechanisms between various techniques. This study provides insight into the understanding and controlling of the aggregation of fungal spores.

Investigation of the Relationship between Permanent Deformation and Dynamic Modulus Performance for Bearing-Layer Asphalt Mixture.

Of major concern is the lack of correlation between the material design and structural function of asphalt pavement in China. The objective of this paper is to identify the layer in asphalt pavement where permanent deformation occurs most seriously and to propose a control index for that layer's asphalt mixture. The permanent deformation of each layer was determined through the utilization of thickness measurements obtained from field cores. The results indicate that the reduction in thickness is more significant in the driving lane than in the ridge band and shoulder. This phenomenon can be attributed to the intensified densification and shearing deformation that arise from the combined impacts of recurrent axle loads and high temperatures. Compared to surface and base layers, the bearing layer is the primary area of concern for permanent deformation in asphalt pavement. Therefore, it is imperative to incorporate the ability of bearing-layer asphalt mixture to withstand permanent deformation as a crucial design parameter. The dynamic modulus of the bearing-layer asphalt mixture is significantly influenced by the type of asphalt, gradation, and asphalt content, compared to other design parameters. Based on the relationship established between dynamic modulus and dynamic stability, with creep rate as the intermediate term, a control standard was proposed to evaluate the permanent deformation of the bearing-layer asphalt mixture. This study can provide reasonable and effective guidance for prolonging pavement life and improving pavement performance.

Nondestructive Detection and Early Warning of Pavement Surface Icing Based on Meteorological Information.

Monitoring and warning of ice on pavement surfaces are effective means to improve traffic safety in winter. In this study, a high-precision piezoelectric sensor was developed to monitor pavement surface conditions. The effects of the pavement surface temperature, water depth, and wind speed on pavement icing time were investigated. Then, on the basis of these effects, an early warning model of pavement icing was proposed using an artificial neural network. The results showed that the sensor could detect ice or water on the pavement surface. The measurement accuracy and reliability of the sensor were verified under long-term vehicle load, temperature load, and harsh natural environment using test data. Moreover, pavement temperature, water depth, and wind speed had a significant nonlinear effect on the pavement icing time. The effect of the pavement surface temperature on icing conditions was maximal, followed by the effect of the water depth. The effect of the wind speed was moderate. The model with a learning rate of 0.7 and five hidden units had the best prediction effect on pavement icing. The prediction accuracy of the early warning model exceeded 90%, permitting nondestructive and rapid detection of pavement icing based on meteorological information.

The change of amino acids samples under metalimnetic oxygen minimum condition: Characterization and mechanism.

The metalimnetic oxygen minimum (MOM) is a common anaerobic phenomenon that occur between 5.00 and 40.00 m of reservoirs. Amino acids (AAs) are widely found in water, but their change in MOM remain unclear. In this study, four AAs with different side chain groups were selected to explore the change of their samples and related disinfection by-products formation potential (DBPFPs) under MOM condition. The results showed that the final degradation rate of dissolved organic carbon and dissolved organic nitrogen of four AAs samples were 11.71%-59.87% and 26.50%-100.00% under MOM condition. Aspartic acid samples were the easiest to be degraded, whereas glycine samples were the opposite. While the total fluorescence intensity increased by 6.30%-113.40% for the appearance of tryptophan-like substance. The total DBPFPs of glutamic acid, arginine and aspartic acid samples were finally decreased by 4.73%, 8.00% and 98.88% (glycine sample increased by 2.30 times). Compared with the surface condition, the degradation of AAs samples and the change of DBPFPs were significantly inhibited under MOM condition. In addition, the diversities of bacterial communities were significantly reduced under MOM condition, which was very unfavorable to the degradation of AAs samples, and in turn affected the control of DBPs and deteriorated the water quality.

Change of algal organic matter under different dissolved oxygen and pressure conditions and its related disinfection by-products formation potential in metalimnetic oxygen minimum.

Most of the reservoirs or lakes will form a metalimnetic oxygen minimum (MOM) with the characterization of a substantial fraction of dissolved oxygen (DO) depleted below the epilimnion. The effect of intracellular organic matter (IOM) of algal cells transformed under MOM conditions is completely different from that of the original IOM on water quality. In this study, the IOM changes of Microcystic aeruginosa under different MOM conditions and its related disinfection by-products formation potentials (DBPFPs) were investigated by changing the pressure and DO concentration of MOM. Total Fmax increased slightly and then decreased under different pressure conditions, finally decreasing by no more than 22.0%. Under aerobic condition, dissolved organic carbon (DOC) and total Fmax decreased significantly, and decreased by 60.4% and 38.8% within the first 2 days. The results of specific UV absorbance (SUVA) and UV250/UV365 indicated that aromatic compounds and average molecular weight of IOM were gradually increased under different MOM conditions. The total DBPFPs increased firstly and then decreased under different pressure conditions, and finally decreased by 26.2%-33.1%. The decrease of total DBPFPs was significantly higher under aerobic condition than that under anoxic condition, which finally decreased by 64.5%. Redundancy analysis showed that the fluorescence parameter (protein-like and humic-like fluorescence) could be expected as an index to predict the DBPFPs. Moreover, the results revealed that with the decrease of DO, the activity and diversity of natural microbial consortium decreased, which prevented the further degradation and utilization of organic matter by natural microbial consortium. Therefore, lower DO was a key player for the deterioration of water quality under MOM conditions.

Effective inactivation of fungal spores by the combined UV/PAA: Synergistic effect and mechanisms.

Peracetic acid (PAA) can effectively inactivate fungi in water, while may pose a potential risk of regrowth after disinfection. The inactivation kinetic and mechanism of fungal spores by combined UV and PAA (UV/PAA) was investigated in this study. The results showed that synergistic factor of the inactivation of A. niger and A. flavus was 1.44 and 1.37, which indicated significant synergistic effect of UV/PAA. The k of A. niger and A. flavus was similar at pH 5.0 and 7.0, while decreased 60.00% and 39.13% at pH 9.0 compared with that at pH 7.0. The effect of HA concentration on the inactivation efficiency of fungal spores by UV/PAA was negative, while the effect of PAA concentration was positive. The membrane permeabilized cell of A. niger and A. flavus caused by UV/PAA was 17.0% and 31.7%, which was higher than that caused by PAA and UV alone. The changes of morphology of fungal spores and the leakage of intracellular material indicated that the damage of cell structure caused by UV/PAA system was more serious than that of UV or PAA alone. In addition, the four parts that contributed in UV/PAA system was in the following order: UV > radical > PAA > synergistic effect. The inactivation efficiency of combined UV and chlorine (UV/Cl2) was higher than that of UV/PAA. Furthermore, the typical order of the inactivation efficiency in different matrix was: phosphate buffer solution > surface water > secondary effluent. The regrowth potential of fungal spores after UV/PAA treatment was significantly lower than that by PAA alone, indicating that UV/PAA could decrease the microbial regrowth potential after PAA disinfection alone.

Mutual-activation between Zero-Valent iron and graphitic carbon for Cr(VI) Removal: Mechanism and inhibition of inherent Side-reaction.

The low reactivity of zero-valent iron (ZVI) usually limits its application for pollutant remediation. Therefore, a microscopic galvanic cell (mGC) with short-circuited cathode and anode was synthesized to intensify its galvanic corrosion. The prepared mGC exhibited 7.14 times higher Fe(II) release performance than ordinary nanoscale-ZVI (nZVI), rendering efficient Cr(VI) removal performance. Density functional theory (DFT) revealed mutual-activation of the cathode and anode due to close proximity, dramatically enhancing the galvanic corrosion of Fe(0) in mGC. The corrosion potential of mGC was measured as -0.77 V, which was 100 mV more negative than nZVI. The released electrons and surface-bond Fe(II) from anode in mGC was proved to be the dominant reductive species. More importantly, Cr(VI) reduction was slightly inhibited by hydroxyl radicals generated by a series of inherent side-reactions in the system, which could be well eliminated by low concentrations of 4-acetamido phenol. This study provides a promising strategy for ZVI activation, and sheds light on its environmental applications.

Adding CuCo2O4-GO to inhibit bromate formation and enhance sulfamethoxazole degradation during the ozone/peroxymonosulfate process: Efficiency and mechanism.

In this work, a new type of catalyst CuCo2O4-GO was synthesized as a heterogeneous catalyst, and its control effect on bromate (BrO3-)generation and sulfamethoxazole (SMX) degradation in O3/PMS process was studied. When 100 mg/L CuCo2O4-GO was added to the reaction system, the BrO3- concentration generated was 0.25 µM at pH = 7.0, 100 µM PMS addition and 1.30 mg/min ozone injection after 30 min reaction. Compared with the 6.58 µM BrO3- produced in the control group, the addition of CuCo2O4-GO prominently inhibited the generation of BrO3- and the inhibition efficiency reached 96.17 %. The addition of CuCo2O4-GO inhibited the conversion of hypobromous acid, thereby inhibiting the formation of BrO3-. Meanwhile, the first-order kinetic constant of the degradation of SMX by O3/PMS and O3/PMS/CuCo2O4-GO was 0.163 and 0.422 min-1, respectively. The addition of CuCo2O4-GO promoted the degradation of SMX and the removal efficiency was reached above 98 % after 10 min reaction. According to the optimization of the GO loading ratio, it was found that CuCo2O4-GO with 20 % GO loading had the best promotion effect on the degradation of SMX, and almost completely inhibited the formation of BrO3-. Finally, in the repeated cycle experiment, CuCo2O4-GO could maintain its high catalytic activity and still had a high removal effect on SMX after three repeated uses. Besides, the BrO3- inhibition efficiency was above 80 % after two repeated uses. Therefore, adding synthetic CuCo2O4-GO is an effective way to control the formation of BrO3- and enhance the degradation of SMX in the O3/PMS process.

Efficacy of UV-LED based advanced disinfection processes in the inactivation of waterborne fungal spores: Kinetics, photoreactivation, mechanism and energy requirements.

The contamination of fungi in water supply systems poses great risks to environment and human health. In this work, UV light-emitting diodes (UV-LEDs)-based advanced disinfection processes (ADPs) including UV-LEDs/hydrogen peroxide (H2O2), UV-LEDs/persulfate (PS) and UV-LEDs/peroxymonosulfate (PMS), were adopted for waterborne fungal spores inactivation. Overall comparisons of the UV-LEDs-based ADPs with respect to the control efficiency of photoreactivation and energy consumption were also evaluated. Results showed that culturability reduction of the fungal spores treated by UV-LEDs was not enhanced with the addition H2O2, PMS, and PS according to the results of heterotrophic plate counts and reaction rate constants; A. niger was expected to have higher UV resistance followed by T. harzianum and P. polonicum. However, UV-LEDs-ADPs inactivation, especially at the wavelengths of 280 and 265/280 nm, could accelerate the permeabilization of fungal spores as characterized by flow cytometry. Take P. polonicum for example, the percentage of membrane permeabilized spores was 98.0%, 98.7%, 97.6% and 82.6% after treatment by UV280/H2O2, UV280/PS, UV280/PMS and UV280 alone, respectively at the fluence of 100 mJ/cm2. The direct attack of free radicals in the processes of UV-LEDs-ADPs further enhanced the membrane damage and lowered the photoreactivation level, thus improved the inactivation efficiency. UV-LEDs/H2O2 was considered as an effective process in the disinfection of fungal spores with the advantages of enhancing the damage of membrane, inhibiting photoreactivation and comparable energy consumption compared with UV-LEDs alone.

The formation kinetics and control of biofilms by three dominant fungi species isolated from groundwater.

Filamentous fungi can enter drinking water supply systems in various ways, and exist in suspended or sessile states which threatens the health of individuals by posing a high risk of invasive infections. In this study, the biofilms formation kinetics of the three genera of fungal spores, Aspergillus niger (A. niger), Penicillium polonicum (P. polonicum) and Trichoderma harzianum (T. harzianum) isolated from the groundwater were reported, as well as the effects of water quality parameters were evaluated. In addition, the efficiency of low- concentrations of chlorine-based disinfectants (chlorine, chlorine dioxide and chloramine) on controlling the formation of fungal biofilms was assessed. The results showed that the biofilms formation of the three genera of fungi could be divided into the following four phases: induction, exponential, stationary and sloughing off. The optimum conditions for fungal biofilms formation were found to be neutral or weakly acidic at 28 °C with rich nutrition. In fact, A. niger, P. polonicum, and T. harzianum were not observed to form mature biofilms in actual groundwater within 120 hr. Carbon was found to have the maximum effect on the fungal biofilms formation in actual groundwater, followed by nitrogen and phosphorus. The resistance of fungal species to disinfectants during the formation of biofilms decreased in the order: A. niger > T. harzianum > P. polonicum. Chlorine dioxide was observed to control the biofilms formation with maximum efficiency, followed by chlorine and chloramine. Consequently, the results of this study will provide a beneficial understanding for the formation and control of fungal biofilms.

The aggregation of Aspergillus spores and the impact on their inactivation by chlorine-based disinfectants.

The formation of fungal biofilm goes through some different states, including monodisperse state, aggregated state, germinated state, hyphal and biofilm. The aggregation of spores is a primary step of fungal biofilm development in aquatic systems. Previous studies on the inactivation of fungi were mostly performed in the monodisperse state of fungal spores and biofilm state, however, the inactivation of aggregated fungal spores is still unclear. In this study, the aggregated characteristics of fungal spores (Aspergillus fumigatus and Aspergillus flavus) at different pH values were firstly studied, and the inactivation efficiency of fungal spores at different aggregation degree by chlorine-based disinfectants was also clarified. The results showed that the aggregation degree of Aspergillus fumigatus was the highest at pH 9.0 while it was the lowest at pH 5.0. Aggregation between fungal spores was mainly mediated by occasional adhesin-adhesin interactions and electrostatic interactions. Compared with monodisperse spores, fungal spores were more resistant to chlorine-based disinfectants with the increase of spore aggregation degree. The inactivation rate constants of Aspergillus fumigatus at 30% and 63% aggregation degree were 1.5- and 4-folds lower than that of monodisperse spores, respectively. The lower proportion of membrane damage and higher intracellular reactive oxygen species level for aggregated spores than monodisperse spores was observed according to the flow cytometric results after chlorine-based disinfectants treatment. The reasons for the lower inactivation efficiency of aggregated spores are as following: the protection of outer layer spores and signals between aggregates lead to the increase of resistance for aggregated spores. This study is meaningful for the control of the fungal spores at different states in water.

Synergistic effect of ozone and chlorine on inactivating fungal spores: Influencing factors and mechanisms.

Effective control of fungal contamination in water is vital to provide healthy and safe drinking water for human beings. Although ozone was highly effective in inactivating fungi in water, it was limited by a lack of continuous disinfection ability in water supply system. In present study, the inactivation of fungal spores by combining ozone and chlorine was investigated. The synergistic effects of Aspergillus niger and Trichoderma harzianum spores reached 0.47- and 0.55-log within 10 min, respectively. The inactivation efficiency and the synergistic effect would be affected by disinfectant concentration, pH, and temperature. The combined inactivation caused more violent oxidative stimulation and more severe damage to the fungal spores than the individual inactivation based on the flow cytometry analysis and the scanning electron microscopy observation. The synergistic effect during the combined inactivation process was attributed to the generation of hydroxyl radicals by the reaction between ozone and chlorine and the promotion of chlorine penetration by the destruction of cell wall by ozone. The combined inactivation efficiency in natural water samples was reduced by 26.4-43.8% compared with that in PBS. The results of this study provided an efficient and feasible disinfection method for the control of fungi in drinking water.

Evaluation of the vital viability and their application in fungal spores' disinfection with flow cytometry.

More attention was focused on fungi contamination in drinking water. Most researches about the inactivation of fungal spores has been conducted on disinfection efficiency and the leakage of intracellular substances. However, the specific structural damage of fungal spores treated by different disinfectants is poorly studied. In this study, the viability assessment methods of esterase activities and intracellular reactive oxygen species (ROS) were optimized, and the effects of chlorine-based disinfectants on fungal spores were evaluated by flow cytometry (FCM) and plating. The optimal staining conditions for esterase activity detection were as follows: fungal spores (106 cells/mL) were stained with 10 µM carboxyfluorescein diacetate and 50 mM ethylene diamine tetraacetic acid at 33 °C for 10 min (in dark). The optimal staining conditions for intracellular ROS detection were as follows: dihydroethidium (the final concentration of 2 µg/mL) was added into fungal suspensions (106 cells/mL), and then samples were incubated at 35 °C for 20 min (in dark). The cell culturability, membrane integrity, esterase activities, and intracellular ROS were examined to reveal the structural damage of fungal spores and underlying inactivation mechanisms. Disinfectants would cause the loss of the cell viability via five main steps: altered the morphology of fungal spores; increased the intracellular ROS levels; decreased the culturability, esterase activities and membrane integrity, thus leading to the irreversible death. It is appropriate to assess the effects of disinfectants on fungal spores and investigate their inactivation mechanisms using FCM.

MiR-9-5p inhibits mitochondrial damage and oxidative stress in AD cell models by targeting GSK-3ß.

This study aims to investigate the effects and underlying mechanisms of overexpression microRNA-9-5p (miR-9-5p) on the Aß-induced mouse hippocampal neuron cell line HT22. Different concentrations of Aß25-35 (10, 20, 40, 80, and 160 µM) treatment were used to establish AD model in HT22 cells. The CCK-8 assay was used to measure the cell viability. The mRNA expression levels of miR-9-5p and glycogen synthase kinase-3ß (GSK-3ß) were determined by RT-qPCR. HT22 cell apoptosis was analyzed flow cytometry. MiR-9-5p was down-regulated in Aß25-35-induced HT22 cells. GSK-3ß is a functional target for miR-9-5p. MiR-9-5p overexpression inhibited Aß25-35-induced mitochondrial dysfunction, cell apoptosis, and oxidative stress by regulating GSK-3ß expression in HT22 cells. Furthermore, through targeting GSK-3ß, overexpression of miR-9-5p partly activated nuclear factor Nrf2/Keap1 signaling, including part increases of Nrf2, HO-1, SOD-1, GCLC expression and slight decrease of Keap1 expression. Our results showed miR-9-5p may play a powerful role in the pathogenesis of AD.

[Fluorescence Characteristics and Source Analysis of DOM in Snowfall of Xi'an].

Fluorescence characteristics and sources of dissolved organic matter (DOM) in snowfall in Xi'an were studied by three-dimensional fluorescence spectroscopy, parallel factor analysis, and backward trajectory model, which provided a data basis for the analysis of the chemical composition and source of atmospheric organic pollutants. Results show that the DOC content of DOM was 0.88-10.92 mg·L-1. DOM mainly contained humus-like, fulvic acid-like, tryptophan-like, and tyrosine-like substances. The fluorescence intensity and the summed intensities of these substances exhibited significant positive correlations with the DOC and UV254 (P<0.01). The fluorescence index (FI), biological source index (BIX), and humic index (HIX) values of DOM during snowfall were 1.50-1.75, 0.87-1.25, and 1.11-1.97, respectively. FI was positively correlated with BIX and negatively correlated with HIX (P<0.05). During snowfall, the air mass transmission trajectories included the local transmission, long-distance transmission starting from Xinjiang (through Gansu and Ningxia), and medium-distance transmissions starting from Inner Mongolia (through Ningxia) and Shandong (via Henan), accounting for 38.78%, 24.04%, 19.87%, and 17.31% of the total, respectively. This indicates that the content or relative content of the DOM contained in the precipitation can be characterized by fluorescence intensities and their sums of the humic-like, fulvic acid-like, tryptophan-like, and tyrosine-like tyrosine. The DOM in snowfall had both biological and terrestrial characteristics, and belonged to a self-generated source with the newly produced organic matter or matter with stronger self-source characteristics. Local transmission had the most significant contribution to the source of snowfall DOM.

The role of synergistic effects between ozone and coagulants (SOC) in the electro-hybrid ozonation-coagulation process.

In order to improve the dissolved organic matter removal efficiency, an electro-hybrid ozonation-coagulation (E-HOC) system was developed in this study, in which the electro-coagulation (EC) and ozonation occurred simultaneously in one integrated unit. Higher removal efficiency was observed for the E-HOC process compared with those of EC, ozonation and pre-ozonation-EC process for the treatment of wastewater treatment plant (WWTP) effluent and ibuprofen (IBP). 58.6% dissolved organic carbon (DOC) removal efficiency was achieved in the E-HOC process for the treatment of WWTP effluent at optimal operational condition (current density 15 mA/cm2, initial pH 5 and ozone dosage 1.5 mg O3/mg DOC). Based on the reactive oxygen species (ROS) detection and reactions on the electrodes, the synergistic effects between ozone and coagulants (SOC) were found to be involved in the E-HOC process. According to pseudo-first-order rate constant analyses, the contribution of five possible organic removal pathways was quantified. It was revealed that the peroxone and SOC effects exhibited almost equal contribution to IBP removal at initial pH 5 under different current densities, both of which played the dominant role in the E-HOC process. However, the contribution of the SOC effects decreased significantly when the initial pH increased to 7 and 9. As an important pathway for organic removal in the E-HOC process at initial pH 5, the mechanism of the SOC effects was analysed at initial pH 5. It was revealed the SOC effects can further improve hydroxyl radicals (•OH) generation, and the surface hydroxyl groups of the hydrolysed Al species generated from anode electrolysis were determined to be the active sites to generate ROS in the SOC effects.

Nutrient drip irrigation for refractory hydrocarbon removal and microbial community shift in a historically petroleum-contaminated soil.

An adequate amount of nutrients is required to enable biodegradation of refractory hydrocarbons in petroleum-contaminated soil. In this study, a microcosm experiment was conducted using a drip fertigation method for petroleum-contaminated soil remediation. Nitrogen and phosphorus were homogeneously and periodically sprayed into a historically contaminated soil using a modified horticultural drip irrigation device. Various petroleum hydrocarbon fraction contents were then determined by gravimetry and gas chromatography (GC), and changes in the soil microbial community were analyzed by high throughput sequencing. After 90 days of remediation, the removal efficiencies of total petroleum hydrocarbon (TPH), saturates, aromatics, C7-C30 n-alkanes, and 16 PAHs were respectively enhanced by 21.5%, 25.5%, 12.4%, 10.4%, and 19.6% compared with the use of a single nutrient amendment application. The high throughput sequencing result showed that obvious changes had occurred in the soil microbial community compositions during drip fertigation; however, fungi were more sensitive to drip fertigation than bacteria. The resulting predominant bacterial and fungal genera were Dietzia, Nocardioides, Mycobacterium, Sphaerobacter, Leifsonia, and Aspergillus, Scolecobasidium, and Fusarium, respectively. Remediating polluted soils by regular fertigation ensures the automatic addition of even amounts of nutrients, which achieves high refractory hydrocarbon removal efficiencies. It is expected that this method can be applied in the in-situ remediation of petroleum-contaminated soil on a large scale.

[Microbial Community Structure Shift During Bioremediation of Petroleum Contaminated Soil Using High Throughput Sequencing].

The shift in microbial community structure during the bioremediation of oil-polluted soil was analyzed by high-throughput sequencing. The results demonstrated obvious changes in the soil microbial community structure and diversity during bioremediation. The species richness and evenness of the microbial community decreased substantially due to the bioaugmentation treatment. Proteobacteria became the predominant phylum, with a relative increase in abundance from 37.44% to 87.44%. Pseudomonas was the most dominant genus, which increased in abundance from 2.99% to 76.37%. In the biostimulation treated soil, the relative abundance of Proteobacteria decreased from 37.44% to 10.90%, while the phylum Firmicutes increased from 9.16% to 35.32%. At the genus level, the relative abundances of Exiguobacterium and Promicromonospora decreased from 8.49% and 18.96% to 2.19% and 14.97%, respectively. Nocardioides and Bacillus became the dominant genera and increased from 5.56% and 0.29% to 28.95% and 22.70%, respectively. The results indicated that bioaugmentation substantially influenced the soil microbial diversity and community structure. Additionally, the biostimulation treatment maintained the balance in the soil microbial community structure. The stabilization of bacteria community structure is beneficial to petroleum biodegradation in the soil.

[Isolation, Identification and Degradation Characteristics of a 17ß-estradiol Degrading Strain Fusarium sp. KY123915].

A 17ß-estradiol (E2) degrading strain (designated as Wu-SP1) was isolated from the activated sludge collected from a wastewater treatment plant (WWTP) in Xi'an. The strain was identified as Fusarium sp. according to 18S rDNA sequence and phylogenetic analysis. The optimal pH and temperature for E2 degradation were 6 and 30℃, respectively. Under these conditions, the E2 biodegradation rate of 2 mg·L-1 E2 amounted to 92.5% within 48 h by this strain. The kinetics of E2 degradation by the strain KY123915 were in good accord with the first-order equation, with the concentration ranged from 10 to 500 mg·L-1. UV spectrum analysis showed the strength of maximum absorption of metabolites became weak compared to E2, indicating that E2 may be degraded via estrone (E1) by Fusarium sp. KY123915.