Enzyme and Mediator-coadsorbed Carbon Felt Electrode for Electrochemical Detection of Glucose Covered with Polymer Layers Based on Layer-by-Layer Technique.

Glucose dehydrogenase (GlDH) and ferrocene were coadsorbed on a carbon felt (CF) sheet (5 × 10 mm, 2 mm thickness), which was used to construct an electrode for the electrochemical detection of glucose. A potential of +0.3 V vs. Ag/AgCl was applied on the base CF, and the current was measured. After the addition of glucose, the current increased and reached a steady state within 50 s. The current response was proportional to the glucose concentration up to 20 µM, with a lower detection limit of 1 µM. The surface of the CF electrode was covered by layers of polystyrene sulfonate and poly-L-lysine using layer-by-layer technique. Again the current response was proportional to glucose concentration up to 20 µM, with a lower detection limit of 2 µM. The oxidation current owing to electrochemical interferents such as L-ascorbate and acetaminophen was 1/8 times of the current observed on the unprotected electrode. In addition, the protection imparted stability to the electrode. Our work demonstrates that a GlDH/ferrocene CF electrode, protected with polystyrene sulfonate and poly-L-lysine, could be used for the electrochemical detection of glucose.

Supporting materials that improve the stability of enzyme membranes.

Long-term stability is a key property of enzyme membranes that can be used for biosensors, bioreactors, and bio-fuel cells. This review discusses factors that decrease the stability, and provides two examples of enzyme membranes, a polyion complex membrane and a cellulose membrane, with which stability loss can be avoided. By using these materials, long-term stability was improved. These supporting materials could be applied to construct biosensors, bioreactors, and bio-fuel cells.

Long-Term Stability of a Cellulose-Based Glucose Oxidase Membrane.

A cellulose-based glucose oxidase membrane was prepared on a glassy carbon (GC) electrode. The current response of the electrode to glucose was measured by applying a potential of 1.0 V vs. Ag/AgCl on the base GC and was proportional to the concentration of glucose up to 1 mM. The long-term stability of the electrode was examined by measuring the daily glucose response. Over four months, the response magnitude was maintained and then gradually decreased. After 11 months, though the response magnitude decreased to 50% of the initial value, the linear response range did not change. Therefore, the electrode could be used as a glucose biosensor even after 11 months of use. The entrapment of the enzyme in the cellulose matrix promoted the stability of the enzyme, as revealed by data on the enzyme activity after the enzyme electrode was immersed in urea. Therefore, the cellulose matrix may be used to improve the performance of biosensors, bioreactors and bio-fuel cells.

Preparation of a cellulose-based enzyme membrane using ionic liquid to lengthen the duration of enzyme stability.

A novel method for preparing enzyme membranes was developed. The enzyme was attached onto the electrode surface by dropping the enzyme solution and allowing it to dry. Glucose oxidase was used for entrapment. Then, the electrode surface was coated with an ionic liquid containing cellulose, and the ionic liquid was removed by immersing the electrode into water. Enzyme activity was retained in the membrane; the enzyme electrode can be used for detecting glucose in the range of 10 µM to 1 mM, and the response time was ~10 s. The stability duration of the electrode was examined: the enzyme electrode could be used for glucose detection for 6 months. The membrane was observed by atomic force microscopy in the force modulation mode; crystalline and amorphous parts were intermingled. In conclusion, the cellulose membrane can be a suitable immobilization matrix for enzymes.

Polyelectrolyte complex membranes for immobilizing biomolecules, and their applications to bio-analysis.

The immobilization of biomolecules is an important technique for bio-analysis, and can be applied to biosensors with both high selectivity and high sensitivity. Many researchers have developed immobilization techniques to optimize these characteristics. In the last two decades, an immobilization technique that meets the desired requirements was developed by using polyelectrolytes to form complexes, based on the electrostatic binding between polycations and polyanions. This review summarizes the techniques used for the immobilization of biomolecules by polyelectrolyte complexes; it also discusses related subjects.

Synthesis and galectin-binding activities of mercaptododecyl glycosides containing a terminal ß-galactosyl group.

Mercaptododecyl glycosides containing a terminal ß-galactosyl group were prepared from D-galactose or from D-lactose via hexa-O-acetyl-lactal (10) as a key intermediate. Interactions of these glycolipids (5 kinds) and galectins (ß-galactoside binding lectins, 6 species) were evaluated by surface plasmon resonance (SPR) method. High binding responses were observed for the lactoside, 2-deoxy-lactoside, and lactosaminide with some galectins (Gal-3, -4, -8), whereas the galactoside and 2,3-dideoxy-lactoside showed low binding activities.

Enzymatically amplified electrochemical detection for lipopolysaccharide using ferrocene-attached polymyxin B and its analogue.

Ferrocene-attached polymyxin B (PMB-Fc) was prepared by the reaction of polymyxin B with ferrocenoyl chloride in a toluene/pyridine mixture. An electrochemical detection of lipopolysaccharide (LPS) was carried out using a combination of PMB-Fc and an enzyme-modified electrode constructed from a glassy carbon electrode modified with a bovine serum albumin membrane containing glucose oxidase. The ferrocene units of the PMB-Fc molecules were oxidized on the electrode, and then reduced to the original neutral form by a glucose oxidase-catalyzed reaction in the presence of D-glucose. The consumption/regeneration cycle for PMB-Fc resulted in a chemically amplified current response. The current response for PMB-Fc decreased in association with its complexation with LPS, and the magnitude of this current decrease caused by LPS was also amplified by the recycling process. The enzyme-modified electrode exhibited a rapid response of 5 min for LPS with the detection limit as low as 50 ng ml(-1). Further, the addition of D-solbitol or poly(vinyl alcohol) of high concentration over 1 mg ml(-1) substantially induced no response, and three kinds of LPS from different strains exhibited similar magnitudes of current response for the same concentrations; these results suggest the advantages of this detection system for practical applications. Ferrocene-attached colistin, an analogue of PMB-Fc, was also effective for the LPS detection using the glucose oxidase-modified electrode.

Comparison of electrode reduction activities of Geobacter sulfurreducens and an enriched consortium in an air-cathode microbial fuel cell.

An electricity-generating bacterium, Geobacter sulfurreducens PCA, was inoculated into a single-chamber, air-cathode microbial fuel cell (MFC) in order to determine the maximum electron transfer rate from bacteria to the anode. To create anodic reaction-limiting conditions, where electron transfer from bacteria to the anode is the rate-limiting step, anodes with electrogenic biofilms were reduced in size and tests were conducted using anodes of six different sizes. The smallest anode (7 cm(2), or 1.5 times larger than the cathode) achieved an anodic reaction-limiting condition as a result of a limited mass of bacteria on the electrode. Under these conditions, the limiting current density reached a maximum of 1,530 mA/m(2), and power density reached a maximum of 461 mW/m(2). Per-biomass efficiency of the electron transfer rate was constant at 32 fmol cell(-1) day(-1) (178 micromol g of protein(-1) min(-1)), a rate comparable to that with solid iron as the electron acceptor but lower than rates achieved with fumarate or soluble iron. In comparison, an enriched electricity-generating consortium reached 374 micromol g of protein(-1) min(-1) under the same conditions, suggesting that the consortium had a much greater capacity for electrode reduction. These results demonstrate that per-biomass electrode reduction rates (calculated by current density and biomass density on the anode) can be used to help make better comparisons of electrogenic activity in MFCs.

Permeation regulation of charged species by the component change of polyion complex membranes.

Three kinds of polyion complex membranes were prepared on a glassy carbon electrode: polycation (poly-L-lysine)-rich membrane, polyanion (DNA)-rich membrane, and equivalent membrane. The permeation of electroactive species (e.g., hydrogen peroxide, L-ascorbate, urate, dopamine) through the membrane was measured by the oxidation current of species at base electrode. Permeation of the anionic species can be depressed through the anion-rich membrane, and permeation of the cation can also be regulated through the cation-rich membrane. It is obvious that the charge exclusion can be controlled by changing the component ratio of polycation and polyanion during preparation.

Electrochemically amplified detection for lipopolysaccharide using ferrocenylboronic acid.

A novel electrochemical technique for lipopolysaccharide (LPS) detection has been developed using a combination of ferrocenylboronic acid derivatives and an enzyme-modified electrode. The enzyme-modified electrode was constructed from a gold electrode modified with a bovine serum albumin membrane containing diaphorase. Ferrocenylboronic acid derivatives are oxidized on the electrode, and then regenerated by a diaphorase-catalyzed reaction in the presence of NADH. The consumption/regeneration cycle for ferrocenylboronic acid derivatives resulted in a chemically amplified current response. The current response for ferrocenylboronic acid derivatives decreased in association with its complexation with glycosyl units of LPS, and this current decrease caused by LPS was also amplified by the recycling process. On the other hand, the addition of a monosaccharide such as D-mannose or D-galactose induced no response at the same LPS concentration. The enzyme membrane immobilized on the electrode plays an important role in selectivity as well as chemical amplification. In addition, the enzyme-modified electrode exhibited a rapid response of 5 min for LPS, which is much faster than the currently used method. The detection limit of LPS from Escherichia coli O127:B8 was as low as 50 ng ml-1.

Microbioassay system for an anti-cancer agent test using animal cells on a microfluidic gradient mixer.

We developed a novel microbioassay system equipped with a gradient mixer of two solutions, and we applied the microfluidic system to an anti-cancer agent test using living animal cells on a microchip. A microchannel for the gradient mixing of two solutions and eight other microchannels for cell assay were fabricated on a poly(dimethylsiloxane) substrate using a soft-lithography method. The functions necessary for this bioassay, i.e., cell culturing, chemical stimulation, cell staining, and fluorescence determination, were integrated into the microfluidic chip. Eight gradient concentrations of the fluorescein solution, ranging from 1 to 98 microg/ml, were archived at 0.1 microl/min on a microchip. A stomach cancer cell line was cultured, and a cell viability assay was conducted using 5-Fluorouracil as an anti-cancer agent on the microchip. Cell viability changed according to the estimated concentration of the agent solution. With the microbioassay system, an anti-cancer agent test was conducted using living cells simultaneously in eight individual channels with the gradient concentration of the agent on a microchip.

Application of integrated SECM ultra-micro-electrode and AFM force probe to biosensor surfaces.

The integration of scanning electrochemical ultra-micro-electrode (UME) with atomic force microscope cantilever probe have been achieved by using a homemade photolithography system. A gold-film-coated AFM cantilever was insulated with photo resist coating and a pointed end of the AFM probe was opened by illuminating with maskless arbitrary optical micro-pattern generator. To realize precise control of probe sample distance constantly, the resulting scanning electrochemical microscopy (SECM)-AFM probe was operated using a dynamic force microscopy (DFM) technique with magnetic field excitation. From a steady-state voltammetric experiment, the effective electrode diameters of the probes thus prepared were estimated to be from 0.050 to 6.2 microm. The capability of this SECM-AFM probe have been tested using gold comb in the presence of Fe(CN)(6)(3-). The simultaneous imaging of the topography and electrochemical activity of the strip electrode was successfully obtained. We also used the SECM-AFM to examine in situ topography and enzymatic activity measurement. Comparison of topography and oxidation current profiles above enzyme-modified electrode showed active parts distribution of biosensor surface.

Electrochemical measurement of phenothiazine-interacted DNA.

The amount of DNA was measured by using thioridazine, which would be attached to the DNA, as an electrochemical indicator. An indicator (thioridazine) solution, a test solution (DNA solution), and a poly-l-lysine solution were successively placed on a glassy carbon electrode, and the electrode was allowed to dry; DNA was immobilized on an electrode surface by the electrostatic binding between DNA and poly-l-lysine. The electrode was immersed into a buffer solution for 15 min, and then differential pulse voltammetry (DPV) was carried out: the oxidation current peak of thioridazine was observed, and its magnitude depended on the amount of DNA in the solution which was used for preparing the electrode. It could be estimated between 0.2 microg DNA (corresponds to 630 pmol nucleotides) to 20 microg DNA (63 nmol nucleotides) from the oxidation peak current of DPV.

Amperometric measurement of ds-DNA content using a peroxidase-modified electrode.

An enzyme electrode with a chemically amplified response for methylene blue (MB) was constructed from a glassy carbon electrode and a layer containing immobilized horseradish peroxidase (HRP). MB is reduced on the electrode but regenerated through the HRP-catalyzed reaction in the presence of H(2)O(2). The electroreduction/regeneration cycle for MB resulted in an amplified electrode response. The enzyme electrode was applied to the highly sensitive measurement of ds-DNA. The current for MB decreased in association with its complexation with DNA, and the current response caused by DNA was also amplified through the recycling processes. The detection limit of ds-DNA (from salmon testes) was as low as 5 ng ml(-1).