Sensitivity, robustness, and reproducibility of U-shaped delamination test for evaluation of candidate ultra-high molecular weight polyethylene materials for joint replacements.

The delamination of ultra-high molecular weight polyethylene (UHMWPE) in artificial joints is a major cause limiting the long-term clinical results of arthroplasty. However, the conventional test method using simple reciprocation to evaluate the delamination resistance of UHMWPE materials has insufficient detection sensitivity. To reproduce delamination, the unconformity contact must be maintained throughout the test so that the maximum stress is generated below the surface. Therefore, a test method that applies a U-shaped motion comprising two long-linear and one short linear sliding motion was developed. The sensitivity, robustness, and reproducibility of the U-shaped delamination test were investigated and compared with the traditional test method. The traditional test method could reproduce delamination only in materials that had degraded considerably, whereas the U-shaped delamination test could reproduce delamination in a wide range of materials, demonstrating its superior sensitivity. Additionally, using a higher load helped accelerate the test without affecting the test results. The optimal length of the short linear sliding motion was confirmed to be 1 mm. Finally, the inter-laboratory reproducibility of the U-shaped delamination test was confirmed using the round-robin test. The U-shaped delamination test demonstrates high sensitivity, robustness, and reproducibility and contributes to the selection and development of UHMWPE materials and artificial joints with a lower risk of delamination.

Rapid Structure Determination of Ranitidine Hydrochloride API in Two Crystal Forms Using Microcrystal Electron Diffraction.

The solid-state properties of drug candidates play a crucial role in their selection. Quality control of active pharmaceutical ingredients (APIs) based on their structural information involves ensuring a consistent crystal form and controlling water and residual solvent contents. However, traditional crystallographic techniques have limitations and require high-quality single crystals for structural analysis. Microcrystal electron diffraction (microED) overcomes these challenges by analyzing difficult-to-crystallize or small-quantity samples, making it valuable for efficient drug development. In this study, microED analysis was able to rapidly determine the configuration of two crystal forms (Forms 1, 2) of the API ranitidine hydrochloride. The structures obtained with microED are consistent with previous structures determined by X-ray diffraction, indicating microED is a useful tool for rapidly analyzing molecular structures in drug development and materials science research.

Mechanical Characterization of Dissolving Microneedles: Factors Affecting Physical Strength of Needles.

Dissolving microneedles (MNs) are novel transdermal drug delivery systems that can be painlessly self-administered. This study investigated the effects of experimental conditions on the mechanical characterization of dissolving MNs for quality evaluation. Micromolding was used to fabricate polyvinyl alcohol (PVA)-based dissolving MN patches with eight different cone-shaped geometries. Axial force mechanical characterization test conditions, in terms of compression speed and the number of compression needles per test, significantly affected the needle fracture force of dissolving MNs. Characterization using selected test conditions clearly showed differences in the needle fracture force of dissolving MNs prepared under various conditions. PVA-based MNs were divided into two groups that showed buckling and unbuckling deformation, which occurred at aspect ratios (needle height/base diameter) of 2.8 and 1.8, respectively. The needle fracture force of PVA-based MNs was negatively correlated with an increase in the needle's aspect ratio. Higher residual water or higher loading of lidocaine hydrochloride significantly decreased the needle fracture force. Therefore, setting appropriate methods and parameters for characterizing the mechanical properties of dissolving MNs should contribute to the development and supply of appropriate products.

Proof of concept testing of a positive reference material for in vivo and in vitro sensitization testing of medical devices.

In vivo skin sensitization tests are required to evaluate the biological safety of medical devices in contact with living organisms to provide safe medical care to patients. Negative and positive reference materials have been developed for biological tests of cytotoxicity, implantation, hemolysis, and in vitro skin irritation. However, skin sensitization tests are lacking. In this study, polyurethane sheets containing 1 wt/wt % 2,4-dinitrochlorobenzene (DNCB-PU) were developed and evaluated as a positive reference material for skin sensitization tests. DNCB-PU sheet extracts prepared with sesame oil elicited positive sensitization responses for in vivo sensitization potential in the guinea pig maximization test and the local lymph node assay. Furthermore, DNCB-PU sheet extracts prepared with water and acetonitrile, 10% fetal bovine serum-containing medium, or sesame oil elicited positive sensitization responses as alternatives to animal testing based on the amino acid derivative reactivity assay, human cell line activation test, and epidermal sensitization assay, respectively. These data suggest that the DNCB-PU sheet is an effective extractable positive reference material for in vivo and in vitro skin sensitization testing in medical devices. The formulation of this reference material will lead to the development of safer medical devices that contribute to patient safety.

Lipid index to quantify the absorbed lipids in retrieved UHMWPE components of joint arthroplasty.

BACKGROUND: The ultra-high molecular weight polyethylene (UHMWPE) component of artificial joints is one of the most important factors affecting the clinical outcomes of joint arthroplasty. Although the possibility of in vivo UHMWPE degradation caused by absorbed lipids has been reported, a quantitative evaluation of this phenomenon has not yet been performed. OBJECTIVE: This study aimed to establish the lipid index (LI) as a quantitative indicator of the amount of absorbed lipids and the first step to quantify their effects on UHMWPE. METHODS: The LI was defined using the infrared spectrum obtained with a Fourier-transform infrared spectrophotometer and verified using the retrieved UHMWPE components. RESULTS: The LI was consistent with the amount of extract recovered in reflux extraction with hexane. In addition, the LI could replace lipid extraction for calculating the oxidation index (OI) because the value obtained by subtracting the LI from the OI showed good agreement with the OI obtained after lipid extraction. CONCLUSION: The LI represents the amount of lipids absorbed by UHMWPE and is useful for quantitatively evaluating the effects of lipids on UHMWPE. In addition, the LI enables OI measurements that are unaffected by absorbed lipids without requiring troublesome lipid-extraction procedures.

In Silico Prediction of N-Nitrosamine Formation Pathways of Pharmaceutical Products.

The recent discovery of N-nitrosodimethylamine (NDMA), a mutagenic N-nitrosamine, in pharmaceuticals has adversely impacted the global supply of relevant pharmaceutical products. Contamination by N-nitrosamines diverts resources and time from research and development or pharmaceutical production, representing a bottleneck in drug development. Therefore, predicting the risk of N-nitrosamine contamination is an important step in preventing pharmaceutical contamination by DNA-reactive impurities for the production of high-quality pharmaceuticals. In this study, we first predicted the degradation pathways and impurities of model pharmaceuticals, namely gliclazide and indapamide, in silico using an expert-knowledge software. Second, we verified the prediction results with a demonstration test, which confirmed that N-nitrosamines formed from the degradation of gliclazide and indapamide in the presence of hydrogen peroxide, especially under alkaline conditions. Furthermore, the pathways by which degradation products formed were determined using ranitidine, a compound previously demonstrated to generate NDMA. The prediction indicated that a ranitidine-related compound served as a potential source of nitroso groups for NDMA formation. In silico software is expected to be useful for developing methods to assess the risk of N-nitrosamine formation from pharmaceuticals.

Fabrication and Characterization of Dissolving Microneedles for Transdermal Drug Delivery of Apomorphine Hydrochloride in Parkinson's Disease.

PURPOSE: We fabricated and characterized polyvinyl alcohol (PVA)-based dissolving microneedles (MNs) for transdermal drug delivery of apomorphine hydrochloride (APO), which is used in treating the wearing-off phenomenon observed in Parkinson's disease. METHODS: We fabricated MN arrays with 11 × 11 needles of four different lengths (300, 600, 900, and 1200 µm) by micromolding. The APO-loaded dissolving MNs were characterized in terms of their physicochemical and functional properties. We also compared the pharmacokinetic parameters after drug administration using MNs with those after subcutaneous injection by analyzing the blood concentration of APO in rats. RESULTS: PVA-based dissolving MNs longer than 600 µm could effectively puncture the stratum corneum of the rat skin with penetrability of approximately one-third of the needle length. Although APO is known to have chemical stability issues in aqueous solutions, the drug content in APO-loaded MNs was retained at 25°C for 12 weeks. The concentration of APO after the administration of APO-loaded 600-µm MNs that dissolved completely in skin within 60 min was 81%. The absorption of 200-µg APO delivered by MNs showed a Tmax of 20 min, Cmax of 76 ng/mL, and AUC0-120 min of 2,829 ng・min/mL, compared with a Tmax of 5 min, Cmax of 126 ng/mL, and AUC0-120 min of 3,224 ng・min/mL for subcutaneous injection. The bioavailability in terms of AUC0-120 min of APO delivered by MNs was 88%. CONCLUSION: APO-loaded dissolving MNs can deliver APO via skin into the systemic circulation with rapid absorption and high bioavailability.

Estimation of confidence intervals for quantitation of coeluted peaks in liquid chromatography-Photodiode array detection through a combination of multivariate curve resolution-alternating least-square and Bayesian inference techniques.

There is a dramatic increase in drug candidates that exhibit complex structures and do not comply with Lipinski's rule of five. One of the most critical and complex technical challenges in the quality control of such drug candidates is the control of analogous substances contained in active pharmaceutical ingredients and related formulations. Although the development of ultrahigh-performance liquid chromatography and high-performance columns has improved efficiency per unit time, the difficulty of peak separation to quantify impurities with similar structures and physicochemical properties continues to rise, and so does the probability of failure to achieve the necessary separation. Coeluting peaks observed in the case of high-performance liquid chromatography (HPLC) with photodiode array detection can be separated using the multivariate curve resolution-alternating least-square (MCR-ALS) method exploiting differences in analyte UV spectra. However, relatively large quantitation errors have been observed for coeluting analogous substances, and the reliability of the corresponding quantitative data requires improvement. Herein, Bayesian inference is applied to separation by the MCR-ALS method to develop an algorithm assigning a confidence interval to the quantitative data of each analogous substance. The usefulness and limitations of this approach are tested using two analogs of telmisartan as models. For this test, a simulated two-component HPLC-UV dataset with an intensity ratio (relative to the main peak) of 0.1-1.0 and a resolution of 0.5-1.0 is used. The developed algorithm allows the prediction confidence interval, including the true value, to be assigned to the peak area in almost all cases, even when the intensity ratio, resolution, and signal-to-noise ratio are changed. Finally, the developed algorithm is also evaluated on a real HPLC-UV dataset to confirm that reasonable prediction confidence intervals including true values are assigned to peak areas. In addition to allowing the separation and quantitation of substances such as impurities challenging to separate by HPLC in a scientifically valid manner, which is impossible for conventional HPLC-UV detection, our method can assign confidence intervals to quantitative data. Therefore, the adopted approach is expected to resolve the issues associated with assessing impurities in the quality control of pharmaceuticals.

Algorithm for the early prediction of drug stability using bayesian inference and multiple measurements: Application for predicting the stability of silodosin tablets.

The stability of active pharmaceutical ingredients (APIs) and formulations has become a major chemistry, manufacturing, and control (CMC) concern in the pharmaceutical industry because it can determine the feasibility of research and development, the development period, and the development costs of a certain formulation. To streamline the research and development of pharmaceutical products and create useful pharmaceutical products at an early stage, a technology that predicts the stability of formulations at an early stage and with a high degree of accuracy is needed. When predicting the stability of a substance, highly reliable data are required; however, the stability data are affected by analytical variations that depend on the experimenter, measurement device, and conditions used. Although these variations greatly affect the prediction accuracy, a stability prediction method that considers these variations has not yet been developed. Here, short-term stability data under accelerated conditions were obtained at three institutions using silodosin tablets as a model sample. By combining Bayesian inference with the temporal change in the amount of the main degradation products obtained and the conventional humidity-corrected Arrhenius equation, we developed a new algorithm that provides a narrow confidence interval, even when using data with variations. By using this algorithm and setting an appropriate number of conditions, we were able to obtain a valid confidence intervals in a short period of time. Here, by performing more measurements than those suggested by the minimum measurement frequency indicated in the guideline specified in the International Council for Harmonisation (ICH) of Technical Requirements for Pharmaceuticals for Human Use, we developed a method that can be used to reasonably predict the long-term stability of the drugs, even if the data measurement interval is short. Our results will help solve various problems in today's pharmaceutical product development scenario and contribute to worldwide health and welfare.

Real-time in situ X-ray micro-computed tomography study of the effect of impurities on the crystallization of amorphous nifedipine.

Controlling the physical stability of noncrystalline active pharmaceutical ingredients remains a major challenge in the development of amorphous formulations such as amorphous solid-dispersion (ASD) formulations. To establish new evaluation and formulation strategies, the spatial distribution of the crystal phase in bulk amorphous nifedipine (NFD) was investigated as a model. The crystallization of amorphous NFD and the effect of a deliberately added impurity were investigated using powder X-ray diffraction (PXRD), differential scanning calorimetry and real-time in situ X-ray micro-computed tomography (X-ray CT). The stability data of amorphous samples, i.e., NFD and a mixture of NFD with an oxidative degradation product of NFD, impurity A (Imp A), at a weight ratio of 90:10, presented as percent amorphous remaining, suggests that Imp A accelerates the bulk crystal growth of NFD. Real-time in situ X-ray CT results showed surface-enhanced crystal growth and cavity formation in solid NFD samples. Moreover, the crystals were heterogeneous in density. These results suggest that Imp A affects the physical stability of the amorphous NFD. X-ray CT equipped with a heating unit can aid in-situ evaluation and assessment of physicochemical properties and physical stability of amorphous samples and formulations.

Folded, undulating, and fibrous doxorubicin sulfate crystals in liposomes.

High-resolution cryogenic transmission electron microscopy (cryo-TEM) evidenced that doxorubicin sulfate crystals in liposomes (prepared by remote loading with ammonium sulfate) form folded, undulating, and fibrous crystals with a diameter of approximately 2.4 nm. An undulating, fibrous crystal considered to be undergrowth, in addition to bundles of fibrous crystals, was also observed in doxorubicin-loaded liposomes. This explains the validity of the formation of doxorubicin sulfate crystals of various shapes, e.g., curved, U-shaped, or circular, in addition to cylinder and/or rod-like crystals reported in the literature. Liposomes that do not contain crystals have inner aqueous phases with high electron density, suggesting that the doxorubicin is remotely loaded and remains as a solute without precipitation.

Advanced Solid-State NMR Analysis of Two Crystal Forms of Ranitidine Hydrochloride: Detection of 1H-14N Intra-/Intermolecular Correlations.

Understanding the characteristics of crystal polymorphism of active pharmaceutical ingredients and analyzing them with high sensitivity is important for quality of drug products, appropriate characterization strategies, and appropriate screening and selection processes. However, there are few methods to measure intra- and intermolecular correlations in crystals other than X-ray crystallography, for which it is sometimes difficult to obtain suitable single crystals. Recently, solid-state NMR has been recognized as a straightforward method for measuring molecular correlations. In this study, we selected ranitidine hydrochloride, which is known to exist in two forms, 1 and 2, as the model drug and investigated each form using solid-state NMR. In conducting the analysis, rotating the sample tube, which had a 1-mm inner diameter, increased the solid-state NMR resolution at 70 kHz. The 1H-14N dipolar-based heteronuclear multiple quantum coherence (D-HMQC) analysis revealed the intermolecular correlation of Form 1 between the N atom of the nitro group and a proton of the furan moiety, which were closer than those of the intramolecular correlation reported using single X-ray crystal analysis. Thus, 1H-14N D-HMQC analysis could be useful for characterizing intermolecular interaction in ranitidine hydrochloride crystals. In addition, we reassigned the 13C solid-state NMR signals of ranitidine hydrochloride according to the liquid-state and multiple solid-state NMR experiments.

Y-specific amh allele, amhy, is the master sex-determining gene in Japanese flounder Paralichthys olivaceus.

Japanese flounder (Paralichthys olivaceus) is an important marine fish species of both fisheries and aquaculture in Northeast Asia. The commercial interest for all-female progenies due to several sex-related traits has prompted basic research on the mechanisms of sex determination in this species. By conducting a linkage analysis of the sex-determining locus, we initially identified 12 microsatellite markers linked to sex in 11 scaffolds, whose localization was restricted to a specific region of linkage group 9. Sequence analysis of this region identified 181 genes based on the UniProt database annotations. Among them, the amh gene was considered a potential candidate for sex determination because this gene is known to have taken over the role of sex determination in many teleosts. An in-depth sequence analysis of both the coding and non-coding regions of amh in XX and XY individuals detected nine SNPs linked with maleness. However, because these substitutions were synonymous, the upstream and downstream regions of amh were also investigated and a male-specific variant with deletions in the promoter region was detected. This truncated Y-specific amh variant was named amhy, and the amh shared by both sexes was named amhx. The association analysis using both females and males of the genotypic sex inferred by the presence/absence of amhy found complete association with phenotypic sex and genotype. Gene expression analysis in larvae derived from a single-pair progeny by quantitative real-time PCR detected amhy transcripts in the larval trunks between 20 and 100 days after hatching only in XY larvae. Localization of amhy by in situ hybridization was detected in presumptive Sertoli cells of XY gonads. Expression of amhx was almost undetectable in both XX and XY genotypes. Loss of Amh function by CRISPR-Cas9 induced male-to-female sex reversal, indicating that this gene was necessary for the masculinization of XY individuals. In conclusion, the complete linkage of amhy with males, its early expression in XY gonads before testicular differentiation, and the induction of sex reversal by loss-of-function mutation support the view that amhy is the sex-determining gene in this species.

[Investigation of Foreign Particles in Moderna COVID-19 Vaccine].

Particular batches of Moderna mRNA Coronavirus Disease 2019 (COVID-19) vaccine were recalled after foreign particles were found in some vaccine vials at the vaccination site in Japan in August 2021. We investigated the foreign particles at the request of the Ministry of Health, Labour and Welfare. Energy dispersive X-ray spectroscopy analysis suggested that the foreign particles found in the vials recalled from the vaccination sites were from stainless steel SUS 316L, which was in line with the findings of the root cause investigation by the manufacturer. The sizes of the observed particles ranged from <50 µm to 548 µm in the major axis. Similar foreign particles were also detected in 2 of the 5 vaccine vials of the same lot stored by the manufacturer, indicating that the foreign particles have already been administered to some people via vaccine. Observation of the vials of the same lot by digital microscope found smaller particles those were not detected by visual inspection, suggesting that more vials were affected. Contrarily, visual inspection and subvisible particulate matter test indicated no foreign particles in the vials of normal lots. Possible root cause and strategies to prevent such a deviation were discussed from technical and regulatory aspects.

A New Method to Visualize the Internal Morphology of Crude Drugs Using High-Resolution X-Ray Computed Tomography.

The microscopic test method (microscopic examination) used to identify crude drugs is a common method in the identification of the original plant source by determining the characteristics from a small sample quantity. However, in recent years, the number of examiners who are familiar with the microscopic examination technique has decreased. In recent years, high-resolution X-ray computed tomography (HRXCT) has been used to visualize the internal structure of plants. HRXCT scans an object using X-rays and enables visualization of the internal structure of the crude drug using a computer. Therefore, in this report, HRXCT was used to easily observe the internal morphology of crude drugs using the Ephedra Herb as an example. The same internal morphological characteristics were observed using both, microscopic examination and HRXCT methods. Image analysis using HRXCT did not require specific techniques, such as sectioning, and the same tissue could be observed from any orientation using a single scan. It afforded remarkable technical simplification and reduction in time to inspect the organization's characteristics. Therefore, image analysis using HRXCT is a useful method for crude drug identifications.

Isolation of N-nitrosodimethylamine from drug substances using solid-phase extraction-liquid chromatography-tandem mass spectrometry.

N-Nitrosodimethylamine (NDMA) has been detected in some drug substances and pharmaceutical products containing sartans, ranitidine and metformin, and a potential risk of NDMA contamination exists in other drug substances and their pharmaceutical products. To quantitate NDMA in various drugs having diverse physicochemical properties, a specific, sensitive, and reliable analytical method is required, in addition to methods that can be applied to a class of nitrosamines. We aimed to develop an off-line isolation method for NDMA in drug substances using SPE for quantification with LC-APCI-MS/MS. Impediments to accurate quantitation of NDMA in drug substances using LC-MS/MS and insufficient durability of the system are attributed to the extremely large amounts of active pharmaceutical ingredients (APIs) in sample solutions in comparison to the trace amount of NDMA. A reduced retention of NDMA and/or decreased separation from other substances in LC, matrix effect in MS detection, and undesirable contamination of instruments with API and other substances may be occasionally encountered, all of which consequently result in deterioration of system performance and generation of unreliable data, even in the cases where a divert valve is configured between the column and ion source of the MS instrument. To address these problems, an off-line NDMA isolation methodology from APIs exhibiting diverse physicochemical properties, namely ranitidine hydrochloride (ranitidine), metformin hydrochloride (metformin), nizatidine, valsartan, and telmisartan, was developed. The applicability of the method was confirmed by batch analysis of metformin and ranitidine. Furthermore, contrary to previous reports, NDMA was found to be stable over a wide pH range. The proposed methodology and data from this study would contribute to the control of NDMA contamination in various drugs to realize the safe delivery of pharmaceuticals to patients.

A method for purifying nanoparticles using cationic modified monoliths and aqueous elution.

Nanoparticles are widely used in the medical field for diagnosis and therapy. In particular, the use of nanoparticles containing vaccines has spread rapidly; hence, ensuring nanoparticle safety and minimizing their side effects have become important concerns worldwide. In this study, we used three types (NH2, poly-Lys, and trimethylaminopropyl) of cationic modified silica monoliths with cylindrical structures, diameters of 4.2 mm, and heights of 1.5 mm. Doxil, an anticancer nanomedicine, and exosomes, as typical nanoparticles, were separated from model leaked drugs (e.g., doxorubicin and oligonucleotides) and proteins (e.g., albumin) coexisting in nanoparticle sample solutions using these monoliths. Each nanoparticle solution (200 µL) was applied to each monolith followed by centrifugation at 9,100 g for 1 min. The ionic concentration of the elution solution was increased stepwise to determine the concentration required to elute the nanoparticles from each monolith by centrifugation. The NH2- and poly-Lys-modified monoliths separated and purified nanoparticles from leaked drugs or proteins coexisting in nanoparticle sample solutions. The nanoparticles were separated from other substances by changing the pH and concentration of the aqueous Tris buffer used as the eluent. Doxil was eluted with 500-1,000 mM Tris buffer (pH 8) when using the NH2-modified monolith, and with 200-1,000 mM Tris buffer (pH 6) when using the poly-Lys-modified monolith. Exosome was obtained using 1,000 mM Tris buffer (pH 8) and the NH2-modified monolith. The recovery efficiencies (ratio of nanoparticle content in the most abundant fraction to that in the sample solution before purification) of Doxil and exosome were 64% and 55%, respectively. Because this method can purify nanoparticles using only low-speed centrifugation for a few minutes, we expect it will be used to improve nanoparticle safety.

Chemical imaging analysis of active pharmaceutical ingredient in dissolving microneedle arrays by Raman spectroscopy.

The purpose of this study was to develop a quality evaluation method for dissolving microneedle arrays (DMNAs) and determine the spatial distribution pattern of drugs in DMNAs. Raman spectroscopy mapping was used to visualize the drug distribution in DMNAs and drug-loaded polymer films as a model. Powder X-ray diffraction (PXRD) and high-pressure liquid chromatography were also performed to characterize DMNAs. Drug-loaded polymer films and DMNAs were prepared by drying the aqueous solutions spread on the plates or casting. PXRD analysis suggested the crystallization of diclofenac sodium (DCF) in several forms depending on its amount in the sodium hyaluronate (HA)-based films. The Raman spectra of HA and DCF showed characteristic and non-overlapping peaks at 1376 and 1579 cm-1 Raman shifts, respectively. The intensity of the characteristic peak of DCF in the DCF-loaded films increased linearly with the increasing drug content in the range of 4.8 to 16.7% (DCF, w/w). Raman imaging analysis revealed a homogenous dispersion of small DCF crystals in these films. Raman imaging indicates the distribution of DCF on the surface of the DMNA needle. This work highlights the benefit of using Raman spectroscopy mapping to reveal the spatial distribution of drugs in DMNAs.

Evaluation of Drug Sorption on Laboratory Materials with Abraham Solvation Parameters of Drugs and its Prevention.

PURPOSE: Undesired drug sorption on laboratory material surfaces reduces the performance of analytical methods and results in the generation of unreliable data. Hence, we characterized the sorption of drugs and evaluated the sorption extent using a linear free energy relationship (LFER) model with Abraham solvation parameters of drugs. Furthermore, to prevent sorption, the effects of additives, such as organic solvents and salts, were evaluated. METHODS: The sorption of fifteen model drugs (concentration: 2 µM), with various physicochemical properties, on materials in 0.2% dimethyl sulfoxide aqueous solutions was evaluated. Drug sorption extent on the materials was determined using high-performance liquid chromatography. The obtained results were analyzed using an LFER model with Abraham solvation parameters of the drugs. The effect of additives on the sorption of itraconazole, one of the most hydrophobic drugs among those tested in this study, was investigated. RESULTS: Sorption was dependent on the physicochemical properties of drugs, rather than the type of materials used, and additives altered the rate of drug sorption. Equations were developed to evaluate the sorption extent (nmol) of drugs to glass and polypropylene using the Abraham solvation parameters of the drugs. CONCLUSIONS: LFER modeling with Abraham solvation parameters of drugs enabled us to evaluate drug sorption on materials. All the additives altered the rate of drug sorption, and some organic solvents effectively prevented sorption. The developed LFER model would be useful for assessment of the sorption properties of compounds in in vitro evaluations in drug discovery research and various other biochemical fields.

N-Nitrosodimethylamine (NDMA) Formation from Ranitidine Impurities: Possible Root Causes of the Presence of NDMA in Ranitidine Hydrochloride.

N-Nitrosodimethylamine (NDMA) is a probable human carcinogen. This study investigated the root cause of the presence of NDMA in ranitidine hydrochloride. Forced thermal degradation studies of ranitidine hydrochloride and its inherent impurities (Imps. A, B, C, D, E, F, G, H, I, J, and K) listed in the European and United States Pharmacopeias revealed that in addition to ranitidine, Imps. A, C, D, E, H, and I produce NDMA at different rates in a solid or an oily liquid state. The rate of NDMA formation from amorphous Imps. A, C, and E was 100 times higher than that from crystalline ranitidine hydrochloride under forced degradation at 110 °C for 1 h. Surprisingly, crystalline Imp. H, bearing neither the N,N-dialkyl-2-nitroethene-1,1-diamine moiety nor a dimethylamino group, also generated NDMA in the solid state, while Imp. I, as an oily liquid, favorably produced NDMA at moderate temperatures (e.g., 50 °C). Therefore, strict control of the aforementioned specific impurities in ranitidine hydrochloride during manufacturing and storage allows appropriate control of NDMA in ranitidine and its pharmaceutical products. Understanding the pathways of the stability related NDMA formation enables improved control of the pharmaceuticals to mitigate this risk.