Mechanical properties and biocompatibility of a novel miniscrew made of Zr70Ni16Cu6Al8 bulk metallic glass for orthodontic anchorage.

The purpose of the present study was to fabricate a miniscrew possible for clinical application using Zr70Ni16Cu6Al8 bulk metallic glass (BMG), which has high mechanical strength, low elastic modulus, and high biocompatibility. First, the elastic moduli of Zr-based metallic glass rods made of Zr55Ni5Cu30Al10, Zr60Ni10Cu20Al10, Zr65Ni10Cu17.5Al7.5, Zr68Ni12Cu12Al8, and Zr70Ni16Cu6Al8 were measured. Zr70Ni16Cu6Al8 had the lowest elastic modulus among them. Then, we fabricated Zr70Ni16Cu6Al8 BMG miniscrews with diameters from 0.9 to 1.3 mm, conducted a torsion test, and implanted them into the alveolar bone of beagle dogs to compare insertion torque, removal torque, Periotest, new bone formation around the miniscrew, and failure rate compared with 1.3 mm diameter Ti-6Al-4 V miniscrew. The Zr70Ni16Cu6Al8 BMG miniscrew exhibited a high torsion torque even if the miniscrew had a small diameter. Zr70Ni16Cu6Al8 BMG miniscrews with a diameter of 1.1 mm or less had higher stability and lower failure rate than 1.3 mm diameter Ti-6Al-4 V miniscrews. Furthermore, the smaller diameter Zr70Ni16Cu6Al8 BMG miniscrew was shown, for the first time, to have a higher success rate and to form more new bone around the miniscrew. These findings suggested the usefulness of our novel small miniscrew made of Zr70Ni16Cu6Al8 BMG for orthodontic anchorage.

Analysis of Chemotactic Property of CCN2/CTGF in Intramembranous Osteogenesis.

Chemotaxis is a directed migration of cells in response to a gradient of extracellular molecules called chemoattractants. Development, growth, remodeling, and fracture healing of bones are advanced through intramembranous osteogenesis. Chemotaxis of preosteoblasts toward future bone formation sites observed in the early stage of intramembranous osteogenesis is a critical cellular process for normal bone formation. However, molecular biological mechanisms of the chemotaxis of preosteoblasts are not fully understood. We have recently clarified, for the first time, the critical role of the cellular communication network factor 2 (CCN2)/connective tissue growth factor (CTGF)-integrin α5-Ras axis for chemotaxis of preosteoblasts during new bone formation through intramembranous osteogenesis. In this chapter, we describe in detail the procedures of the in vivo and in vitro assays to investigate the chemotactic property of CCN2/CTGF and its underlying molecular biological mechanisms during intramembranous osteogenesis.

Vibration accelerates orthodontic tooth movement by inducing osteoclastogenesis via transforming growth factor-ß signalling in osteocytes.

BACKGROUND: We previously found the conditions of supplementary vibration that accelerated tooth movement and induced bone resorption in an experimental rat tooth movement model. However, the molecular biological mechanisms underlying supplementary vibration-induced orthodontic tooth movement are not fully understood. Transforming growth factor (TGF)-ß upregulates osteoclastogenesis via induction of the receptor activator of nuclear factor kappa B ligand expression, thus TGF-ß is considered an essential cytokine to induce bone resorption. OBJECTIVES: The aim of this study is to examine the role of TGF-ß during the acceleration of orthodontic tooth movement by supplementary vibration. MATERIALS AND METHODS: In experimental tooth movement, 15 g of orthodontic force was loaded onto the maxillary right first molar for 28 days. Supplementary vibration (3 g, 70 Hz) was applied to the maxillary first molar for 3 min on days 0, 7, 14, and 21. TGF-ß receptor inhibitor SB431542 was injected into the submucosal palatal and buccal areas of the maxillary first molars once every other day. The co-culture of RAW264.7 cells and MLO-Y4 cells was used as an in vitro osteoclastogenesis model. RESULTS: SB431542 suppressed the acceleration of tooth movement and the increase in the number of osteoclasts by supplementary vibration in our experimental rat tooth movement model. Immunohistochemical analysis showed supplementary vibration increased the number of TGF-ß1-positive osteocytes in the alveolar bone on the compression side during the experimental tooth movement. Moreover, vibration-upregulated TGF-ß1 in MLO-Y4 cells induced osteoclastogenesis. CONCLUSIONS: Orthodontic tooth movement was accelerated by supplementary vibration through the promotion of the production of TGF-ß1 in osteocytes and subsequent osteoclastogenesis.

Automated Grooming Detection of Mouse by Three-Dimensional Convolutional Neural Network.

Grooming is a common behavior for animals to care for their fur, maintain hygiene, and regulate body temperature. Since various factors, including stressors and genetic mutations, affect grooming quantitatively and qualitatively, the assessment of grooming is important to understand the status of experimental animals. However, current grooming detection methods are time-consuming, laborious, and require specialized equipment. In addition, they generally cannot discriminate grooming microstructures such as face washing and body licking. In this study, we aimed to develop an automated grooming detection method that can distinguish facial grooming from body grooming by image analysis using artificial intelligence. Mouse behavior was recorded using a standard hand camera. We carefully observed videos and labeled each time point as facial grooming, body grooming, and not grooming. We constructed a three-dimensional convolutional neural network (3D-CNN) and trained it using the labeled images. Since the output of the trained 3D-CNN included unlikely short grooming bouts and interruptions, we set posterior filters to remove them. The performance of the trained 3D-CNN and filters was evaluated using a first-look dataset that was not used for training. The sensitivity of facial and body grooming detection reached 81.3% and 91.9%, respectively. The positive predictive rates of facial and body grooming detection were 83.5% and 88.5%, respectively. The number of grooming bouts predicted by our method was highly correlated with human observations (face: r = 0.93, body: r = 0.98). These results highlight that our method has sufficient ability to distinguish facial grooming and body grooming in mice.

Effect of vibration on orthodontic tooth movement in a double blind prospective randomized controlled trial.

The purpose of the present study was to investigate the effect of vibration on orthodontic tooth movement and safety assessment based on our previous basic research in animal experiments. A double-blind prospective randomized controlled trial using split-mouth design was conducted in patients with malocclusion. The left and right sides of maxillary arch were randomly assigned to vibration (TM + V) and non-vibration (TM) groups. After leveling, vibrations (5.2 ± 0.5 g-forces (gf), 102.2 ± 2.6 Hertz (Hz)) were supplementary applied to the canine retracted with 100 gf in TM + V group for 3 min at the monthly visit under double-blind fashion, and the canine on the other side without vibration was used as TM group. The amount of tooth movement was measured blindly using a constructed three-dimensional dentition model. The amount of canine movement per visit was 0.89 ± 0.55 mm in TM group (n = 23) and 1.21 ± 0.60 mm in TM + V group (n = 23), respectively. There was no significant difference of pain and discomfort, and root resorption between the two groups. This study indicates that static orthodontic force with supplementary vibration significantly accelerated tooth movement in canine retraction and reduced the number of visits without causing side effects.

Stomatognathic functional improvement in a patient with a canted occlusal plane and temporomandibular disorder treated with an edgewise appliance and miniscrews.

Generally, a canted occlusal plane results in esthetic problems, such as an asymmetric mandible with midline deviation, and functional problems, such as temporomandibular disorder (TMD). For many years, orthognathic surgery has been used to level a canted occlusal plane. However, similar effects might be achieved by intruding the posterior teeth using a miniscrew. This case report describes a patient with a canted occlusal plane, mandibular deviation, shifted dental midlines, and TMD treated with an edgewise appliance using miniscrews as anchorage. Vertical control of posterior teeth with miniscrews enabled flattening of the canted occlusal plane. Dental midlines were coincided with the midfacial line, thereby improving smile symmetry. During 4 years of retention, the patient maintained ideal occlusion. Furthermore, TMD symptoms disappeared, and significant improvements in stomatognathic functions were observed compared with those at pretreatment. These results suggest that miniscrews can be used to improve canted occlusal plane and stomatognathic malfunctions.

15-hydroxy eicosadienoic acid is an exacerbating factor for nasal congestion in mice.

Allergic rhinitis (AR) is one of the most common allergic inflammatory diseases worldwide. In AR, increased blood flow and vascular permeability in nasal mucosa cause rhinorrhea and nasal congestion. We investigated the role of an 11Z,14Z-eicosadienoic acid-derived metabolite, 15-hydroxy-11Z,13Z-eicosadienoic acid (15-HEDE), in functional changes in vasculature and nasal congestion in AR. Repeated intranasal administration of Ovalbumin (OVA) caused AR symptoms, such as sneezing and nasal congestion, in mice. OVA administration increased the level of 15-HEDE in nasal lavage fluid, which reached approximately 0.6 ng/ml after ten OVA treatments. Upon measuring vascular contraction, treatment with 0.1-3 µM 15-HEDE did not cause contraction in mouse aortae, while it dilated aortae that were pre-contracted by thromboxane receptor stimulation. Pretreatment with the voltage-gated K+ (KV ) channel inhibitor 4-aminopyridine significantly inhibited the 15-HEDE-induced vascular relaxation. Intravital imaging showed that administration of 1 µg 15-HEDE dilated blood vessels, and Mile's assay demonstrated that this administration also caused dye leakage, indicating vascular hyperpermeability in mouse ears. Computed tomography scanning and morphological study revealed that administration of 3 µg 15-HEDE narrowed nasal passages and thickened nasal mucosa in mice. Finally, we confirmed that treating mice with 3 µg 15-HEDE caused rhinitis symptoms, such as abdominal breathing, and reduced respiratory frequency, suggesting nasal congestion. 15-HEDE caused vasodilation by activating KV channels and increased vascular permeability, which may lead to nasal congestion. Furthermore, 15-HEDE might be a new lipid mediator that exacerbates nasal congestion in AR.

Scleraxis upregulated by transforming growth factor-ß1 signaling inhibits tension-induced osteoblast differentiation of priodontal ligament cells via ephrin A2.

During tooth movement in orthodontic treatment, bone formation and resorption occur on the tension and compression sides of the alveolar bone, respectively. Although the bone formation activity increases in the periodontal ligament (PDL) on the tension side, the PDL itself is not ossified and maintains its homeostasis, indicating that there are negative regulators of bone formation in the PDL. Our previous report suggested that scleraxis (Scx) has an inhibitory effect on ossification of the PDL on the tension side through the suppression of calcified extracellular matrix formation. However, the molecular biological mechanisms of Scx-modulated inhibition of ossification in the tensioned PDL are not fully understood. The aim of the present study is to clarify the inhibitory role of Scx in osteoblast differentiation of PDL cells and its underlying mechanism. Our in vivo experiment using a mouse experimental tooth movement model showed that Scx expression was increased during early response of the PDL to tensile force. Scx knockdown upregulated expression of alkaline phosphatase, an early osteoblast differentiation marker, in the tensile force-loaded PDL cells in vitro. Transforming growth factor (TGF)-ß1-Smad3 signaling in the PDL was activated by tensile force and inhibitors of TGF-ß receptor and Smad3 suppressed the tensile force-induced Scx expression in PDL cells. Tensile force induced ephrin A2 (Efna2) expression in the PDL and Efna2 knockdown upregulated alkaline phosphatase expression in PDL cells under tensile force loading. Scx knockdown eliminated the tensile force-induced Efna2 expression in PDL cells. These findings suggest that the TGF-ß1-Scx-Efna2 axis is a novel molecular mechanism that negatively regulates the tensile force-induced osteoblast differentiation of PDL cells.

Connective tissue growth factor promotes chemotaxis of preosteoblasts through integrin α5 and Ras during tensile force-induced intramembranous osteogenesis.

In vertebrates, new bone formation via intramembranous osteogenesis is a critical biological event for development, remodeling, and fracture healing of bones. Chemotaxis of osteoblast lineage cells is an essential cellular process in new bone formation. Connective tissue growth factor (CTGF) is known to exert chemotactic properties on various cells; however, details of CTGF function in the chemotaxis of osteoblast lineage cells and underlying molecular biological mechanisms have not been clarified. The aim of the present study was to evaluate the chemotactic properties of CTGF and its underlying mechanisms during active bone formation through intramembranous osteogenesis. In our mouse tensile force-induced bone formation model, preosteoblasts were aggregated at the osteogenic front of calvarial bones. CTGF was expressed at the osteogenic front, and functional inhibition of CTGF using a neutralizing antibody suppressed the aggregation of preosteoblasts. In vitro experiments using µ-slide chemotaxis chambers showed that a gradient of CTGF induced chemotaxis of preosteoblastic MC3T3-E1 cells, while a neutralizing integrin α5 antibody and a Ras inhibitor inhibited the CTGF-induced chemotaxis of MC3T3-E1 cells. These findings suggest that the CTGF-integrin α5-Ras axis is an essential molecular mechanism to promote chemotaxis of preosteoblasts during new bone formation through intramembranous osteogenesis.

Ten-m/Odz3 regulates migration and differentiation of chondrogenic ATDC5 cells via RhoA-mediated actin reorganization.

Tenascin-like molecule major (Ten-m)/odd Oz (Odz), a type II transmembrane molecule, is well known to modulate neural development. We have reported that Ten-m/Odz3 is expressed in cartilaginous tissues and cells. Actin cytoskeleton and its regulator ras homolog gene family member A (RhoA) are closely associated with chondrogenesis. The present study aimed to evaluate the function and molecular mechanism of Ten-m/Odz3 during chondrogenesis, focusing on RhoA and the actin cytoskeleton. Ten-m/Odz3 was expressed in precartilaginous condensing mesenchyme in mouse limb buds. Ten-m/Odz3 knockdown in ATDC5 induced actin cytoskeleton reorganization and change of cell shape through modulation of RhoA activity and FGF2 expression. Ten-m/Odz3 knockdown suppressed ATDC5 migration and expression of genes associated with chondrogenesis, such as Sox9 and type II collagen, via RhoA. On the other hand, Ten-m/Odz3 knockdown inhibited proliferation of ATDC5 in a RhoA-independent manner. These findings suggest that Ten-m/Odz3 plays an important role in early chondrogenesis regulating RhoA-mediated actin reorganization.

Methionine Enkephalin Suppresses Osteocyte Apoptosis Induced by Compressive Force through Regulation of Nuclear Translocation of NFATc1.

Mechanical stress stimulates bone remodeling, which occurs through bone formation and resorption, resulting in bone adaptation in response to the mechanical stress. Osteocytes perceive mechanical stress loaded to bones and promote bone remodeling through various cellular processes. Osteocyte apoptosis is considered a cellular process to induce bone resorption during mechanical stress-induced bone remodeling, but the underlying molecular mechanisms are not fully understood. Recent studies have demonstrated that neuropeptides play crucial roles in bone metabolism. The neuropeptide, methionine enkephalin (MENK) regulates apoptosis positively and negatively depending on cell type, but the role of MENK in osteocyte apoptosis, followed by bone resorption, in response to mechanical stress is still unknown. Here, we examined the roles and mechanisms of MENK in osteocyte apoptosis induced by compressive force. We loaded compressive force to mouse parietal bones, resulting in a reduction of MENK expression in osteocytes. A neutralizing connective tissue growth factor (CTGF) antibody inhibited the compressive force-induced reduction of MENK. An increase in osteocyte apoptosis in the compressive force-loaded parietal bones was inhibited by MENK administration. Nuclear translocation of NFATc1 in osteocytes in the parietal bones was enhanced by compressive force. INCA-6, which inhibits NFAT translocation into nuclei, suppressed the increase in osteocyte apoptosis in the compressive force-loaded parietal bones. NFATc1-overexpressing MLO-Y4 cells showed increased expression of apoptosis-related genes. MENK administration reduced the nuclear translocation of NFATc1 in osteocytes in the compressive force-loaded parietal bones. Moreover, MENK suppressed Ca2+ influx and calcineurin and calmodulin expression, which are known to induce the nuclear translocation of NFAT in MLO-Y4 cells. In summary, this study shows that osteocytes expressed MENK, whereas the MENK expression was suppressed by compressive force via CTGF signaling. MENK downregulated nuclear translocation of NFATc1 probably by suppressing Ca2+ signaling in osteocytes and consequently inhibiting compressive force-induced osteocyte apoptosis, followed by bone resorption. © 2020 The Authors. JBMR Plus published by Wiley Periodicals, Inc. on behalf of American Society for Bone and Mineral Research.

Delayed tooth movement in Runx2+/- mice associated with mTORC2 in stretch-induced bone formation.

Runt-related transcription factor 2 (Runx2) is an essential transcription factor for osteoblast differentiation, and is activated by mechanical stress to promote osteoblast function. Cleidocranial dysplasia (CCD) is caused by mutations of RUNX2, and CCD patients exhibit malocclusion and often need orthodontic treatment. However, treatment is difficult because of impaired tooth movement, the reason of which has not been clarified. We examined the amount of experimental tooth movement in Runx2+/- mice, the animal model of CCD, and investigated bone formation on the tension side of experimental tooth movement in vivo. Continuous stretch was conducted to bone marrow stromal cells (BMSCs) as an in vitro model of the tension side of tooth movement. Compared to wild-type littermates the Runx2+/- mice exhibited delayed experimental tooth movement, and osteoid formation and osteocalcin (OSC) mRNA expression were impaired in osteoblasts on the tension side of tooth movement. Runx2 heterozygous deficiency delayed stretch-induced increase of DNA content in BMSCs, and also delayed and reduced stretch-induced alkaline phosphatase (ALP) activity, OSC mRNA expression, and calcium content of BMSCs in osteogenic medium. Furthermore Runx2+/- mice exhibited delayed and suppressed expression of mammalian target of rapamycin (mTOR) and rapamycin-insensitive companion of mTOR (Rictor), essential factors of mTORC2, which is regulated by Runx2 to phosphorylate Akt to regulate cell proliferation and differentiation, in osteoblasts on the tension side of tooth movement in vivo and in vitro. Loss of half Runx2 gene dosage inhibited stretch-induced PI3K dependent mTORC2/Akt activity to promote BMSCs proliferation. Furthermore, Runx2+/- BMSCs in osteogenic medium exhibited delayed and suppressed stretch-induced expression of mTOR and Rictor. mTORC2 regulated stretch-elevated Runx2 and ALP mRNA expression in BMSCs in osteogenic medium. We conclude that Runx2+/- mice present a useful model of CCD patients for elucidation of the molecular mechanisms in bone remodeling during tooth movement, and that Runx2 plays a role in stretch-induced proliferation and osteogenesis in BMSCs via mTORC2 activation.

A comparative assessment of orthodontic treatment outcomes of mild skeletal Class III malocclusion between facemask and facemask in combination with a miniscrew for anchorage in growing patients: A single-center, prospective randomized controlled trial.

OBJECTIVES: To investigate the hypothesis that there is difference in the treatment outcomes of milder skeletal Class III malocclusion between facemask and facemask in combination with a miniscrew in growing patients. MATERIALS AND METHODS: Patients were randomly divided into two groups. In one group, the patients were treated with facemask therapy (FM group: 12 males, eight females, average age: 10 years, 5 months ± 1 year, 8 months). In the other group, patients were treated with facemask therapy along with a miniscrew (FM+MS group: 12 males, seven females, average age: 11 years, 1 month ± 1 year, 3 months). A lingual arch with hooks was fixed to the maxillary arch in both groups and a protractive force of 500 g was applied from the facemask to the hooks. The patients were instructed to use the facemask for 12 hours per day. In the FM+MS group, a miniscrew was inserted into the palate and fixed to the lingual arch. RESULTS: Mobility and loosening of the miniscrew were not observed during treatment. Lateral cephalometric analysis showed that SNA, SN-ANS, and ANB values were significantly increased in the FM+MS group compared with those for the FM group (SNA, 1.1° SN-ANS, 1.3° ANB, 0.8°). Increase in proclination of maxillary incisors was significantly greater in the FM group than in the FM+MS group (U1-SN, 5.0°). CONCLUSIONS: During treatment of milder skeletal Class III malocclusion, facemask therapy along with a miniscrew exhibits fewer negative side effects and delivers orthopedic forces more efficiently to the maxillary complex than facemask therapy alone.

Improvement of Open Bite and Stomatognathic Function in an Axenfeld- Rieger Syndrome Patient by Orthodontic Sectional Arch Mechanics: Clinical Considerations and the Risk of Orthodontic Tooth Movement.

Orthodontists need to understand the orthodontic risks associated with systemic disorders. Axenfeld-Rieger syndrome (ARS) is a rare autosomal dominant disorder with genetic and morphological variability. The risks of orthodontic treatment in ARS patients have been unclear. Here we describe the correction of an anterior open bite in a 15-year-old Japanese female ARS patient by molar intrusion using sectional archwires with miniscrew implants. An undesirable development of external apical root resorption (EARR) was observed in all intrusive force-applied posterior teeth during the patient's orthodontic treatment, suggesting that ARS patients have a higher risk of EARR than the general population.

Vibration enhances osteoclastogenesis by inducing RANKL expression via NF-κB signaling in osteocytes.

To shorten the duration of orthodontic treatment it is important not only to reduce risks such as dental caries, periodontal disease, and root resorption, but also to decrease pain and discomfort caused by a fixed appliance. Several studies have investigated the effect of vibration applied to fixed appliances to accelerate tooth movement. Although it was reported that vibration accelerates orthodontic tooth movement by enhancing alveolar bone resorption, the underlying cellular and molecular mechanisms remain unclear. In this study, we investigated the effects of vibration on osteoclastogenesis in vitro and in vivo. Vibration applied to pre-osteoclast cell line RAW264.7 cells enhanced cell proliferation but did not affect their differentiation into osteoclasts. Osteocytes in bone are known to be mechanosensitive and to act as receptor activator of nuclear factor kappa B (NF-κB) ligand (RANKL). Therefore, in the present study, vibration was applied to cells from the osteocyte-like cell line MLO-Y4. In MLO-Y4 cells, vibration induced phosphorylation of the inhibitor of NF-κB (IκB) and caused nuclear localization of NF-κB p65. Additionally, vibration increased RANKL mRNA expression, but did not affect osteoprotegerin (OPG) mRNA expression in MLO-Y4 cells, thus resulting in an increased RANKL/OPG ratio. Consistent with these findings, vibration applied during experimental tooth movement increased NF-κB activation and RANKL expression in osteocytes on the compression side of alveolar bone in vivo, whereas vibration had no such effects on the tension side. Furthermore, in a co-culture of MLO-Y4 cells and RAW264.7 cells, vibration applied to MLO-Y4 cells enhanced osteoclastogenesis. These findings suggest that vibration could accelerate orthodontic tooth movement by enhancing osteoclastogenesis through increasing the number of pre-osteoclasts and up-regulating RANKL expression in osteocytes on the compression side of alveolar bone via NF-κB activation.

Insulin-like growth factor 1 modulates bioengineered tooth morphogenesis.

Regenerative therapy to replace missing teeth is a critical area of research. Functional bioengineered teeth have been produced by the organ germ method using mouse tooth germ cells. However, these bioengineered teeth are significantly smaller in size and exhibit an abnormal crown shape when compared with natural teeth. The proper sizes and shapes of teeth contribute to their normal function. Therefore, a method is needed to control the morphology of bioengineered teeth. Here, we investigated whether insulin-like growth factor 1 (IGF1) can regulate the sizes and shapes of bioengineered teeth, and assessed underlying mechanisms of such regulation. IGF1 treatment significantly increased the size of bioengineered tooth germs, while preserving normal tooth histology. IGF1-treated bioengineered teeth, which were developed from bioengineered tooth germs in subrenal capsules and jawbones, showed increased sizes and cusp numbers. IGF1 increased the number of fibroblast growth factor (Fgf4)-expressing enamel knots in bioengineered tooth germs and enhanced the proliferation and differentiation of dental epithelial and mesenchymal cells. This study is the first to reveal that IGF1 increases the sizes and cusp numbers of bioengineered teeth via the induction of enamel knot formation, as well as the proliferation and differentiation of dental epithelial and mesenchymal cells.

Orthodontic correction of severe Class II malocclusion in a patient with Prader-Willi syndrome.

Prader-Willi syndrome (PWS) is a complex disorder that affects multiple systems and may cause craniofacial and dentofacial abnormalities. However, there is still a lack of evidence in the literature regarding the progress of orthodontic treatment in patients with PWS. This case report describes the successful orthodontic treatment of a patient with PWS. A girl, 9 years 0 months of age, who had been diagnosed with PWS had protruding maxillary incisors and a convex profile. Her malocclusion was due to the posteriorly positioned mandible. Screening tests for sleep apnea syndrome showed that she had sleep-disordered breathing, including obstructive sleep apnea and bruxism. We also observed an excessive overjet of 10.0 mm, a deep overbite of 6.8 mm, and the congenital absence of the mandibular second premolars. The patient was diagnosed with an Angle Class II malocclusion and a skeletal Class II jaw-base relationship with a deep overbite. Functional appliance therapy with mandibular advancement, which can enlarge the upper airway and increase the upper airspace, was performed to prevent further deterioration of the patient's obstructive sleep apnea. An acceptable occlusion with a proper facial profile and functional excursion were achieved without interference after comprehensive 2-stage treatment that incorporated orthodontic therapy for the patient's excessive overjet and deep overbite. The resulting occlusion was stable, and the occlusal force and the contact area gradually increased over a 2-year retention period. These results suggest that orthodontic treatment offers the opportunity to greatly improve the health and quality of life of people with PWS.

Biosafety, stability, and osteogenic activity of novel implants made of Zr70Ni16Cu6Al8 bulk metallic glass for biomedical application.

Superior mechanical and chemical properties of Zr70Ni16Cu6Al8 bulk metallic glass (BMG) demonstrate its promise as a novel biomaterial for fabrication of implants. The aim of the present study was to validate mechanical, chemical, and biological properties of Zr70Ni16Cu6Al8 BMG through comparison with titanium (Ti). Our data indicated higher tensile strength, lower Young's modulus, and reduced metal ion release of Zr70Ni16Cu6Al8 BMG compared with Ti. Biosafety of bone marrow mesenchymal cells on Zr70Ni16Cu6Al8 BMG was comparable to that of Ti. Next, screw-type implant prototypes made of Zr70Ni16Cu6Al8 BMG were fabricated and inserted into rat long bones. Zr70Ni16Cu6Al8 BMG implants indicated a higher removal-torque value and lower Periotest value compared with Ti implants. In addition, higher amounts of new bone formation and osseointegration were observed around Zr70Ni16Cu6Al8 BMG implants compared with Ti implants. Moreover, gene expression analysis displayed higher expression of osteoblast- and osteoclast-associated genes in the Zr70Ni16Cu6Al8 BMG group compared with the Ti group. Importantly, loading to implants upregulated bone formation, as well as osteoblast- and osteoclast-associated gene expression in the peri-implant area. No significant difference in concentrations of Ni, Al, Cu, and Zr in various organs was shown between in the Zr70Ni16Cu6Al8 BMG and Ti groups. Collectively, these findings suggest that Zr70Ni16Cu6Al8 BMG is suitable for fabricating novel implants with superior mechanical properties, biocompatibility, stability, and biosafety compared with Ti. STATEMENT OF SIGNIFICANCE: Titanium is widely used to fabricate orthopedic and dental implants. However, Titanium has disadvantages for biomedical applications in regard to strength, elasticity, and biosafety. Recently, we developed a novel hypoeutectic Zr70Ni16Cu6Al8 BMG, which has superior mechanical and chemical properties. However, the validity of Zr70Ni16Cu6Al8 BMG for biomedical application has not been cleared. The aim of the present study was to validate the mechanical, chemical, and biological properties of Zr70Ni16Cu6Al8 BMG for biomedical applications through comparison with Titanium. The present study clarifies that Zr70Ni16Cu6Al8 BMG has good mechanical properties, corrosion resistance, and osteogenic activity, which are necessary features for biomedical applications. The present study provides for the first time the superiority of Zr70Ni16Cu6Al8 BMG implants to Titanium implants for biomedical applications.

Comparison of changes in irregularity and transverse width with nickel-titanium and niobium-titanium-tantalum-zirconium archwires during initial orthodontic alignment in adolescents: A double-blind randomized clinical trial.

OBJECTIVES: The purpose of this prospective, double-blind, randomized clinical trial was to compare the clinical efficiency of nickel-titanium (NiTi) and niobium-titanium-tantalum-zirconium (TiNbTaZr) archwires during initial orthodontic alignment. MATERIALS AND METHODS: All subjects (ages between 12 and 20 years) underwent nonextraction treatment using 0.022-inch brackets. All patients were randomized into two groups for initial alignment with 0.016-inch NiTi archwires (n = 14), or with 0.016-inch TiNbTaZr archwires (n = 14). Digital scans were taken during the course of treatment and were used to compare the improvement in Little's Irregularity Index and the changes in intercanine and intermolar widths. RESULTS: There was approximately a 27% reduction in crowding during the first month with the use of 0.016-inch TiNbTaZr (Gummetal) wire, and an additional 25% decrease in crowding was observed during the next month. There was no significant difference between the two treatment groups in the decrease in irregularity over time ( P = .29). There was no significant difference between the two groups in the changes in intercanine and intermolar width ( P = .80). CONCLUSIONS: It can be concluded that Gummetal wires and conventional NiTi wires possess a similar ability to align teeth, and Gummetal wires have additional advantages over conventional NiTi, such as formability and use in patients with nickel allergy.