Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 6 de 6
Filter
Add more filters










Database
Language
Publication year range
1.
Chem Asian J ; 17(16): e202200567, 2022 Aug 15.
Article in English | MEDLINE | ID: mdl-35726484

ABSTRACT

Over the past few years, the environmentally friendly synthesis of nanomaterials, including graphene using green chemistry, has attracted tremendous attention due to its easy handling, low cost, and biocompatibility. Here we demonstrate a facile and efficient green synthesis route for producing highly stable and electrochemically active three-dimensional interconnected graphene frameworks (3DIGF) from jute sticks. Initially, jute sticks derived three-dimensional amorphous activated carbon nanosheets (3DAACNs) were prepared at low temperatures (i. e., 850 °C) in an inert environment. The resultant 3DAACNs were then heat treated at a high temperature (i. e., 2700 °C) under an inert environment, resulting in 3DIGF. The prepared carbonaceous materials were fully characterized, and various experimental techniques confirmed the preparation of 3DIGF. The prepared 3DIGF shows a highly stable nature in thermal and chemical environments and demonstrates a highly dynamic nature for the electrooxidation of sulfide. This study could be considered a vital contribution towards the economic and simple approach for preparing 3DIGF from biomass.


Subject(s)
Graphite , Biomass , Graphite/chemistry
2.
Membranes (Basel) ; 11(6)2021 May 27.
Article in English | MEDLINE | ID: mdl-34072048

ABSTRACT

This review discusses the roles of anion exchange membrane (AEM) as a solid-state electrolyte in fuel cell and electrolyzer applications. It highlights the advancement of existing fabrication methods and emphasizes the importance of radiation grafting methods in improving the properties of AEM. The development of AEM has been focused on the improvement of its physicochemical properties, including ionic conductivity, ion exchange capacity, water uptake, swelling ratio, etc., and its thermo-mechano-chemical stability in high-pH and high-temperature conditions. Generally, the AEM radiation grafting processes are considered green synthesis because they are usually performed at room temperature and practically eliminated the use of catalysts and toxic solvents, yet the final products are homogeneous and high quality. The radiation grafting technique is capable of modifying the hydrophilic and hydrophobic domains to control the ionic properties of membrane as well as its water uptake and swelling ratio without scarifying its mechanical properties. Researchers also showed that the chemical stability of AEMs can be improved by grafting spacers onto base polymers. The effects of irradiation dose and dose rate on the performance of AEM were discussed. The long-term stability of membrane in alkaline solutions remains the main challenge to commercial use.

3.
Materials (Basel) ; 13(23)2020 Nov 26.
Article in English | MEDLINE | ID: mdl-33256129

ABSTRACT

Anion exchange membrane fuel cells (AEMFCs) are attractive alternatives to proton exchange membrane fuel cells due to their ability to employ nonprecious metals as catalysts, reducing the cost of AEMFC devices. This paper presents an experimental exploration of the carbon support material effects on AEMFC performance. The silver (Ag) nanoparticles supported on three types of carbon materials including acetylene carbon (AC), carbon black (CB), and multiwalled carbon nanotube (MWCNT)-Ag/AC, Ag/CB, and Ag/MWCNT, respectively-were prepared using the wet impregnation method. The silver loading in the catalysts was designed as 60 wt.% during the synthesizing process, which was examined using thermogravimetric analysis. The elemental composition of the prepared Ag/AC, Ag/CB, and Ag/MWCNT catalysts was confirmed using X-ray diffraction analysis. The nanoparticle size of Ag attached on carbon particles or carbon nanotubes, as observed by scanning electron microscopy (SEM), was around 50 nm. For the performance tests of a single AEMFC, the obtained results indicate that the maximum power density using Ag/MWCNT as the cathode catalyst (356.5 mW·cm-2) was higher than that using Ag/AC (329.3 mW·cm-2) and Ag/CB (256.6 mW·cm-2). The better cell performance obtained using a MWCNT support can be ascribed to the higher electrical conductivity and the larger electrochemical active surface area calculated from cyclic voltammetry measurements.

4.
Materials (Basel) ; 12(13)2019 Jun 26.
Article in English | MEDLINE | ID: mdl-31247928

ABSTRACT

The performance of an anion exchange membrane fuel cell (AEMFC) under various operating conditions, including cell temperature and humidification of inlet gases, was systematically investigated in this study. The experimental results indicate that the power density of an AEMFC is susceptible to the cell temperature and inlet gas humidification. A high performance AEMFC can be achieved by elevating the cell operating temperature along with the optimization of the gas feed dew points at the anode and cathode. As excess inlet gas humidification at the anode is supplied, the flooding is less severe at a higher cell temperature because the water transport in the gas diffusion substrate by evaporation is more effective upon operation at a higher cell temperature. The cell performance is slightly affected when the humidification at the anode is inadequate, owing to dehydration of the membrane, especially at a higher cell temperature. Furthermore, the cell performance in conditions of under-humidification or over-humidification at the cathode is greatly reduced at the different cell temperatures tested due to the dehydration of the anion exchange membrane and the water shortage or oxygen mass transport limitations, respectively, for the oxygen reduction reaction. In addition, back diffusion could partly support the water demand at the cathode once a water concentration gradient between the anode and cathode is formed. These results, in which sophisticated water management was achieved, can provide useful information regarding the development of high-performance AEMFC systems.

5.
Appl Opt ; 51(8): 1122-30, 2012 Mar 10.
Article in English | MEDLINE | ID: mdl-22410992

ABSTRACT

We present a new semiellipsoid microlens fabrication method that controls the printing gap in the UV lithography process without thermal reflow. The UV proximity printing method can precisely control the curvature radius ratio of the semiellipsoid microlens in the fabrication process. The proposed fabrication method facilitates mass production to achieve a high-yield and high-coupling semiellipsoid microlens that is suitable to be used in commercial fiber transmission systems. A semiellipsoid microlens can be tipped on a single-mode fiber end to improve power coupling efficiency from laser diodes. The semiellipsoid microlens allows increasing the fiber spot size and numerical aperture. It is very important to control the geometric parameters in the assembly procedure to increase the optical coupling efficiency between the laser diode and single-mode fiber. Wide misalignment tolerance, low loss, and low manufacturing cost could be achieved by the proposed fabrication method. The theoretical model is first developed to predict the optical coupling efficiency for various microstructure geometries of semiellipsoid microlens and assembly parameters in this study. Then, the Taguchi method is applied to obtain the optimal geometric parameters setting. The results show that optical coupling efficiency could be significantly improved by using the optimal geometric parameters setting.

6.
Biomed Microdevices ; 6(1): 47-53, 2004 Mar.
Article in English | MEDLINE | ID: mdl-15307444

ABSTRACT

In this article, we propose a versatile CD-like multi-channel electrophoresis-based biomedical separation system that is driven by the interactive forces between the centrifugal force and the electric field force. The centrifugal force control of this system is realized through the velocity control of a DC servo motor, while the electric field is governed through the concentric conducting circuits, which are suitably designed and fabricated by sputtering on metal mask method, and can be adjusted to provide multi-stage voltages. Experimental results demonstrate that the electro-osmotic flow (EOF) effect can be effectively reduced when the electric field force and centrifugal force are in the opposite direction. Benefits from this are that the electrophoresis separation time can be prolonged and the length of the microfluidic channels can be shortened; therefore, more effective separation efficiency can be obtained. Moreover, other advantages, such as lower joule-heat generation, low-chemistry reaction, and no variation on the ion concentration during processes, make this biomedical separation system more useful.


Subject(s)
Biopolymers/isolation & purification , Centrifugation/instrumentation , Compact Disks , Electrophoresis/instrumentation , Microfluidic Analytical Techniques/instrumentation , Centrifugation/methods , Electromagnetic Fields , Electrophoresis/methods , Equipment Design , Equipment Failure Analysis , Microfluidic Analytical Techniques/methods , Stress, Mechanical
SELECTION OF CITATIONS
SEARCH DETAIL
...