Physicochemical characteristics of grease-trap wastewater with different potential mechanisms of FOG solid formation, separation, and accumulation inside grease traps.

This work investigates the physicochemical characteristics of grease-trap wastewater discharged from a large community market. It proposes potential mechanisms of fat, oil, and grease (FOG) solid formation, separation, and accumulation inside grease traps. Sixty-four samples, i.e., the floated scum, suspended solid-liquid wastewater, and settled sludge, were collected from the grease-trap inlet and outlet chambers. A lower pH of 5-6 at 25-29 °C inside the grease trap than those reported under the sewer conditions (pH 6-7) was revealed. A significant difference in solid and dissolved constituents was also discovered between the inlet and outlet chambers, indicating that the baffle wall could affect the separation mechanism. The sludge samples had 1.5 times higher total solids (TS) than the scum samples, i.e., 0.225 vs. 0.149 g g-1 TS, revealing that the sludge amount impacted more significantly the grease trap capacity and operation and maintenance. In contrast, the scum samples had 1.4 times higher volatile solids (VS) than the sludge samples, i.e., 0.134 vs. 0.096 g g-1 VS, matching with the 64.2 vs. 29.7% of carbon content from CHN analysis. About 2/3 of the free fatty acids (FFAs) with palmitic acids were the primary saturated FFAs, while the remaining 1/3 of unsaturated FFAs were found in the solid and liquid samples. Although up to 0.511 g g-1 FOG can be extracted from the scum samples, none from the sludge samples. More diverse minerals/metals other than Na, Cl, and Ca were found in the sludge samples than in the scum samples. Grease-trap FOG solids and open drain samples exhibited similar physicochemical properties to those reported in the literature. Four potential mechanisms (crystallization, emulsification, saponification, and baffling) were presented. This work offers insights into the physicochemical properties of grease-trap wastewater that can help explore its FOG solid formation, separation, and accumulation mechanisms inside a grease trap.

Recovery of oil from palm oil mill effluent using polypropylene micro/nanofiber.

Residual palm oil that goes into the river untreated can become detrimental to the environment. Residual oil discharge during milling process into palm oil mill effluent (POME) is unavoidable. About 1 wt% of residual oil in POME causes major problems to the mills, in terms of environment, wastewater treatment and economy losses. This paper reports the recovery of residual oil from POME by adsorption on polypropylene micro/nanofiber (PP-MNF) and desorption of oil by hands pressing, and oil extraction from the PP-MNF using solvent and supercritical-CO2 extraction techniques. The characterization of the PP-MNF and the quality of oil extracted were analyzed using analytical instruments. The reusability of the PP-MNF was also investigated. The experimental results showed the adsorption capacity of the PP-MNF was 28.65 g of oil/g of PP-MNF on average using refined palm oil, whilst recovery of oil from POME was 10.93 g of oil/g of PP-MNF. The extraction yield of oil from PP-MNF using hand pressing was 89.62%. The extraction of residual oil from the pressed PP-MNF showed comparable yield between solvent and supercritical CO2 techniques. The quality of recovered oil was similar with the quality of the crude oil, and no trace of polypropylene contamination was detected in the oil recovered. The PP-MNF showed no significant physical change after the extraction process. In conclusion, the PP-MNF has great potential to be used commercially in residual oil recovery from POME.

Esterification of residual palm oil using solid acid catalyst derived from rice husk.

In this study, carbon-silica based acid catalysts derived from rice husks (RH) were successfully synthesised using microwave (MW) technology. The results showed that MW sulphonation produced Sulphur (S) content of 17.2-18.5 times higher than in raw RH. Fourier-transform Infrared Spectroscopy (FTIR) showed peak at 1035 cm-1 which corresponded to O˭S˭O stretching of sulphonic (-SO3H) group. XRD showed sulfonated RH catalysts (SRHCs) have amorphous structure, and through SEM, broadening of the RH voids and also formation of pores is observed. RH600 had the highest surface area of 14.52 m2/g. SRHCs showed high catalytic activity for esterification of oleic acid with methanol with RH600 had the highest initial formation rate (6.33 mmolL-1min-1) and yield (97%). The reusability of the catalyst showed gradually dropped yield of product for every recycle, which might be due to leaching of -SO3H. Finally, esterification of oil recovered from palm oil mill effluent (POME) with methanol achieved a conversion of 87.3% free fatty acids (FFA) into fatty acid methyl esters (FAME).

Co-composting of palm oil mill sludge-sawdust.

Composting of Palm Oil Mill Sludge (POMS) with sawdust was conducted in natural aerated reactor. Composting using natural aerated reactor is cheap and simple. The goal of this study is to observe the potential of composting process and utilizing compost as media for growing Cymbopogun citratus, one of Malaysia herbal plant. The highest maximum temperature achieved is about 40 degrees C and to increase temperature bed, more biodegradable substrate needs to be added. The pH value decrease along the process with final pH compost is acidic (pH 5.7). The highest maximum organic losses are about 50% with final C/N ratio of the compost is about 19. Final compost also showed some fertilizing value but need to be adjusted to obtain an ideal substrate. Addition of about 70% sandy soil causes highest yield and excellent root development for C. citratus in potted media. Beside that, compost from POMS-sawdust also found to have fertilizer value and easy to handle. Composting of POMS with sawdust shows potential as an alternative treatment to dispose and recycle waste components.