ABSTRACT
Tungsten, in amounts ranging from micrograms to milligrams, can be extracted into isoamyl alcohol, as the tungsten(V) ferrocyanide complex obtained by reduction of tungsten(VI) with tin(II) in 4M hydrochloric acid containing ferrocyanide. It can thus be separated from iron, cobalt, chromium, manganese, arsenic, antimony, bismuth, silicon, calcium and copper, their precipitation being prevented by addition of glycerol and, in the case of iron, sulphosalicyclic acid. Molybdenum, vanadium and nickel are not separated from tungsten, however. Tungsten can also be determined spectrophotometrically as tungsten(V) ferrocyanide. The absorbance of the brown complex is measured in aqueous solution or preferably after extraction into isoamyl alcohol. As many alloying elements interfere, they should be separated by the ferrocyanide extraction or other suitable method. Both the separation and the determination methods give satisfactory results with an overall error of not more than 0.5% in the analysis of practical samples containing low or high percentages of tungsten.
ABSTRACT
Vanadium(V) is conveniently reduced by sodium dithionite to vanadium(III) which is extracted as its picolinate complex into chloroform. Vanadium is determined spectrophotometrically by measuring the absorbance of the complex at 385 nm against a reagent blank, Beer's law being obeyed over the range 1-50 microg/ml. The method is one of the most selective, being free from interference by relatively high concentrations of almost all the important elements, titanium, chromium, manganese, iron, cobalt, nickel, zinc, copper, aluminium, molybdenum, tungsten and uranium, found in industrial alloys. Only bismuth interferes. The method is quite simple and rapid. It has been successfully applied for the analysis of vanadium in a variety of samples.
ABSTRACT
Phosphotungsten blue is produced by tin(II) reduction of tungstate solution complexed with phosphate at a w/w ratio of W/P = 5, in 4M hydrochloric acid medium, and extracted with isoamyl alcohol; thus tungsten is separated from Fe(III), Ni, Co, Cr(III), V(V), As(V), Sb(III), Bi, Si, U(VI), Ca and Cu(II). In presence of bismuth (0.5 mg/ml), 99.7% W is separated in a single extraction. After alkaline back-extraction, tungsten is determined spectrophotometrically as phosphotungsten blue; it is measured at 930 nm in aqueous solution or at 900-960 nm after isoamyl alcohol extraction, the Beer's law ranges being 0.08-0.6 and 0.16-0.72 mg/ml respectively. The methods are shown to give satisfactory results in the analysis of practical samples containing some milligrams of tungsten.
ABSTRACT
Tungsten can be extracted quantitatively as phosphotungstate in micro as well as milligram concentrations by extraction with MIBK from 0.1-1M hydrochloric acid if the w/w tungsten:phosphorus ratio = 7, and separated from Fe, Ni, Co, Cr, Mn, Cu, Ca, U, Th, As, Sb, Bi and Si, after reduction of Fe(III) and cr(VI) with thiosulphate, in natural and industrial samples. Mo and V suppress the extraction of tungsten and therefore require prior separation. The method takes 15 min for a single separation and gives highly satisfactory results with an overall error of about 0.1-0.2% over the range 10-100 mg tungsten in the sample.
ABSTRACT
Molybdenum(V) is quantitatively precipitated as sulphide (99.7%) from 0.1 M At hydrochloric acid without formation of molybdenum blue and without need for a long digestion. Precipitation is more complete and co-precipitation less than with Mo(VI) sulphide. The precipitate can also be used directly for gravimetric estimation. In the presence of EDTA, molybdenum(V) sulphide is not precipitated from 0.1 M hydrochloric acid and can be separated from copper, bismuth, antimony and tin sulphides and determined cerimetrically in presence of the EDTA.
ABSTRACT
Vanadium(V) is rapidly reduced by dithionite to V(III) which is extracted as the oxinate into carbon tetrachloride. Vanadium is determined by measuring absorbance of the complex at lambda(max) = 420-425 nm with a sensitivity of 0.004 microg/cm(2) and Beer's law range of 0-7 microg/ml . Several mg of some important elements can be tolerated if they are masked. Molybdenum interferes seriously. The method has been applied to synthetic samples, rutile and ilmenite with satisfactory results. Using ordinary reagents and taking 10 min or less in series for a determination, the method has a sensitivity rarely exceeded by others with a much higher tolerance for other elements.
ABSTRACT
Small amounts of tungsten in natural and industrial samples can be freed from all important interfering elements by extraction of molybdenum by xanthate, reduction of tungsten by mercury and extraction of tungsten(V) thiocyanate into tribenzylamine, and finally back-extraction. The tungsten can be then determined as tetraphenylarsonium tungstate by precipitating it at pH 2-4, filtering it off and drying it at 110 degrees for 45 min. An overall error of 0.1-0.2% is obtained for 5-60 mg of tungsten.
ABSTRACT
Tungsten(V) is formed by shaking for 2 min sodium tungstate solution in 0.4 M potassium thiocyanate-4M hydrochloric acid medium, with mercury. It is titrated with standard iron(III) solution. The thiocyanate present stabilizes W(V) to aerial oxidation and also acts as indicator. The W(V) can also be titrated potentiometrically in 7M hydrochloric acid, a tungsten wire electrode being used. Fe, Ni, Cr, Zr, Bi, Sb, Ce, Al, Pb, Ca and U do not interfere. Cu, V and As can be tolerated up to 5 mg. Co, Mo, Re, Nb and Mn interfere, but not in the potentiometric determination. The method is direct, simple, rapid, accurate and reproducible.
ABSTRACT
A simple method is described for the extraction of V(II) as its pyridine thiocyanate complex. Vanadate is reduced to V(II) in 1-2N sulphuric acid by zinc amalgam. Thiocyanate and pyridine are added, the solution is adjusted to pH 5.2-5.5 and the complex extracted with chloroform. The vanadium is back-extracted with peroxide solution. Zinc from the reductant accompanies the vanadium but alkali and alkaline earth metal ions, titanium, uranium, chromium and aluminium are separated, besides those ions reduced to the elements by zinc amalgam. The method takes about 20 min and is applicable to microgram as well as milligram amounts of vanadium.
ABSTRACT
The yellow W(V) thiocyanate complex is formed by shaking sodium tungstate solution in 0.2-0.8M potassium thiocyanate and 4-5M hydrochloric acid, with mercury. It is extracted with 2% tribenzylamine solution in chloroform and measured at 410 nm. U, Ti, V, Cr, Fe, Co, Ni, Mn, Al, Pb, Sn, Bi, Pd, Sb and Cu do not interfere. Pt and Mo in amount equal to that of tungsten give errors of up to 0.4 and 2% respectively. The sensitivity is 0.013 mug ml and Beer's law is obeyed up to 24 mug ml .
ABSTRACT
A study of the conditions for precipitation of molybdenum(V) hydroxide shows that for Mo concentration 1 mg ml about 97.5% of the Mo can be precipitated between pH 5 and 5.8. Lower concentrations of molybdenum(V) or molybdenum(VI) can be precipitated quantitatively by using 20 times the amount of zirconium as collector, at the same pH. On this basis, a simple method is given for quantitative separation of rhenium from large amounts of molybdenum and is attested by analysis of synthetic and molybdenite samples.
ABSTRACT
A simple and rapid spectrophotometric determination of molybdenum is described. The molybdenum thiosulphate complex is extracted into isoamyl alcohol from 1.0-1.5M hydrochloric acid containing 36-40 mg of Na(2)S(2)O(3).5H(2)O per ml. The absorbance at lambda(max) = 475 nm obeys Beer's law over the range 0-32 microg of Mo per ml of solvent phase. Up to 5 mg/ml of Ti(IV), V(V), Cr(VI), Fe(III), Co(II), Ni(II), U(VI), W(VI), Sb(III), 1 mg/ml of Cu(II), Sn(II), Bi(V) and 10 microg/ml of Pt(IV) and Pd(II) do not interfere. Large amounts of complexing agents interfere. The method has been applied to analysis of synthetic and industrial samples.
ABSTRACT
A simple and selective extraction of molybdenum is described. Tungsten is masked with tartaric acid and molybdenum(VI) is reduced in 2M hydrochloric acid by boiling with hydrazine sulphate. Iron, copper and vanadium are then masked with ascorbic acid, thiourea and potassium hydrogen fluoride respectively. The molybdenum(V) is extracted as its xanthate complex into chloroform, from 1M hydrochloric acid that is 0.4M potassium ethyl xanthate. The complex is decomposed by excess of liquid bromine, and the molybdenum is stripped into alkaline hydrogen peroxide solution. The molybdenum is then determined by standard methods. Large amounts of Cu(II), Mn(II), Fe(III), Ti(IV), Zr, Ce(IV), V(V), Nb, Cr(VI), W(VI), U(VI), Re(VII) and Os(VIII) do not interfere. Several synthetic samples and ferromolybdenum have been rapidly and satisfactorily analysed by the method.
ABSTRACT
A simple method is described for the rapid spectrophotometric determination of molybdenum in samples containing 1-60% Mo, with satisfactory accuracy. Molybdenum is reduced with excess of hydrazine sulphate in boiling 5.5M hydrochloric acid and extracted with isoamyl acetate from 7M hydrochloric acid. The green colour is measured at 720 nm against a reagent blank. Beer's law is obeyed over the range 0.08-5.4 mg of molybdenum per ml. Interference from iron and copper is removed by adding stannous chloride and thiourea respectively in slight excess. Titanium, vanadium, niobium, chromium, tungsten, nickel, uranium, and antimony do not interfere even in large amounts. Only cobalt interferes seriously.
ABSTRACT
A simple method is described for the separation of molybdenum from titanium, zirconium, chromium, manganese, iron, cobalt, nickel, uranium and aluminium in a wide variety of samples in <30 min. Phosphomolybdenum blue is produced by boiling for 2 min a molybdate solution containing phosphate to give Mo/P = 20-37 (w/w) with hydrazine sulphate in 0.1N sulphuric acid. The volume and acidity are adjusted to give a molybdenum concentration of 0.6-5 my/ml in 0.4-0.5N sulphuric acid. The phosphomolybdenum blue is 99.5% extracted with methyl isobutyl ketone in a single extraction. The residual molybdenum and hydrazine in the aqueous phase are oxidized with a few drops of liquid bromine and the molybdenum is quantitatively extracted with the same solvent from 1N sulphuric acid as its reddish brown thiosulphato complex. The molybdenum is stripped by ammonia-hydrogen peroxide solution. The back-extract is heated to boiling and filtered to remove the insoluble hydroxides of traces of accompanying elements. The thiosulphate in the filtrate is destroyed by boiling for 4-5 min with excess of hydrogen peroxide in slightly ammoniacal medium. The molybdenum is determined finally by cerimetry or other standard methods.
ABSTRACT
Reduction in 1 M H(2)SO(4) with liquid zinc amalgam and extraction with isopentanol from 3M H(2)SO(4), separates rhenium from almost all the interfering elements of importance in rhenium determination. The small amounts of Mo, U, Fe and Ru still accompanying rhenium are removed by the thiocyanate-pentyl acetate or the oxine-chloroform extraction. The method is simple, rapid and of very wide applicability. It is particularly useful in the determination of rhenium in various alloys and tungsten-containing samples.
