A portable inflatable soft wearable robot to assist the shoulder during industrial work.

Repetitive overhead tasks during factory work can cause shoulder injuries resulting in impaired health and productivity loss. Soft wearable upper extremity robots have the potential to be effective injury prevention tools with minimal restrictions using soft materials and active controls. We present the design and evaluation of a portable inflatable shoulder wearable robot for assisting industrial workers during shoulder-elevated tasks. The robot is worn like a shirt with integrated textile pneumatic actuators, inertial measurement units, and a portable actuation unit. It can provide up to 6.6 newton-meters of torque to support the shoulder and cycle assistance on and off at six times per minute. From human participant evaluations during simulated industrial tasks, the robot reduced agonist muscle activities (anterior, middle, and posterior deltoids and biceps brachii) by up to 40% with slight changes in joint angles of less than 7% range of motion while not increasing antagonistic muscle activity (latissimus dorsi) in current sample size. Comparison of controller parameters further highlighted that higher assistance magnitude and earlier assistance timing resulted in statistically significant muscle activity reductions. During a task circuit with dynamic transitions among the tasks, the kinematics-based controller of the robot showed robustness to misinflations (96% true negative rate and 91% true positive rate), indicating minimal disturbances to the user when assistance was not required. A preliminary evaluation of a pressure modulation profile also highlighted a trade-off between user perception and hardware demands. Finally, five automotive factory workers used the robot in a pilot manufacturing area and provided feedback.

Air Efficient Soft Wearable Robot for High-Torque Elbow Flexion Assistance.

Recent developments in soft wearable robots have shown promise for assistive and rehabilitative use-cases. For inflatable approaches, a major challenge in developing portable systems is finding a balance between portability, performance, and usability. In this paper, we present a textile-based robotic sleeve that can provide functional elbow flexion assistance and is compatible with a portable actuation unit (PAU). Flexion is driven by a curved textile actuator with internal pneumatic supports (IPS). We show that the addition of IPS improves torque generation and increases battery-powered actuations by 60%. We demonstrate that the device can provide enough torque throughout the ROM of the elbow joint for daily life assistance. Specifically, the device generates 13.5 Nm of torque at 90°. Experimental testing in five healthy individuals and two individuals with Amyotrophic Lateral Sclerosis (ALS) demonstrates its impact on wearer muscle activity and kinematics. The results with healthy subjects show that the device was able to reduce the bicep muscle activity by an average of 49.1±13.3% during static and dynamic exercises, 43.6±11.1% during simulated ADLs, and provided an assisted ROM of 134°±13°. Both ALS participants reported a reduced rate of perceived exertion during both static and dynamic tasks while wearing the device and had an average ROM of 115°±8°. Future work will explore other applications of the IPS and extend the approach to assisting multiple joints.

C-Term Faraday Rotation in Low Symmetry tert-Butyl Substituted Polyferroceniums.

Molecular thin films are currently being investigated as candidate materials to replace conventional atomistic inorganic crystal-based Faraday rotators. High symmetry paramagnetic species have been reported to exhibit large Verdet constants via magnetic field splitting of degenerate ground states. However, lower symmetry open-shell species have not been extensively studied. Herein, we report the Faraday rotation of two poly di-tert-butylferroceniums with diphenylsilane and vinylene linkers. Thin films of oxidized poly[(1,1'-di-tert-butylferrocenyl)diphenylsilane] [poly(tBu2fc-SiPh2)] displayed a 30% increase in maximum Verdet constant relative to the previously reported decamethylferrocenium/PMMA composite, with Verdet constants of -4.52 × 104 deg T-1 m-1 at 730 nm and 4.46 × 104 deg T-1 m-1 at 580 nm. When a sp2-type linker was used, as with the oxidized poly(1,1'-di-tert-butyl-ferrocenylene)vinylene [poly(tBu2fc-C═C)], negligible Faraday rotation was observed. Hence, Faraday rotation can be maintained when molecular symmetry is broken, however orbital symmetry breaking in optical transitions of interest leads to a significant loss in magneto-optical activity.

Tunable, Textile-Based Joint Impedance Module for Soft Robotic Applications.

The design of soft actuators is often focused on achieving target trajectories or delivering specific forces and torques, rather than controlling the impedance of the actuator. This article outlines a new soft, tunable pneumatic impedance module based on an antagonistic actuator setup of textile-based pneumatic actuators intended to deliver bidirectional torques about a joint. Through mechanical programming of the actuators (select tuning of geometric parameters), the baseline torque to angle relationship of the module can be tuned. A high bandwidth fluidic controller that can rapidly modulate the pressure at up to 8 Hz in each antagonistic actuator was also developed to enable tunable impedance modulation. This high bandwidth was achieved through the characterization and modeling of the proportional valves used, derivation of a fluidic model, and derivation of control equations. The resulting impedance module was capable of modulating its stiffness from 0 to 100 Nm/rad, at velocities up to 120°/s and emulating asymmetric and nonlinear stiffness profiles, typical in wearable robotic applications.