ABSTRACT
We carried out KF postdeposition treatment (PDT) on a Cu(In,Ga)Se2 (CIGS) layer with a process time varying from 50 to 200 s. The highest CIGS solar-cell efficiency was achieved at a KF PDT process time of 50 s; in this condition, we observed the highest level of K element at the near-surface of the CIGS layer and the perfectly passivated pinholes on the CIGS surface. At process times above 150 s, the oversupplied KF agglomerated into large islands and was subsequently eliminated during the deposition of the chemical bath deposition (CBD)-Zn(O,S) buffer layer owing to the islands' water-soluble characteristics. As a result, the growth mechanism of the CBD-Zn(O,S) layer varied as a function of KF PDT process time. X-ray photoemission spectroscopy (XPS) measurements were used to examine the dependency of the chemical state on the KF PDT process time, and from the results, we formulated a chemical reaction model based on the shift in the elemental binding energy following deposition of the CBD-Zn(O,S) buffer layer. The chemical states of the K-In-Se phase, which have a beneficial effect on the solar-cell performance owing to the formation of durable and improved p-n junctions, are formed only at a KF PDT process time of 50 s. We derived band alignments from the XPS depth profiles by extracting the conduction- and valence-band offsets, and we used optical-pump-THz-probe spectroscopy to measure the ultrafast photocarrier lifetimes related to the defect states following KF PDT. Our key findings can be summarized as follows: (i) photocarrier transport is beneficial at a low barrier height, and (ii) the photocarrier lifetime increases when the K-In-Se phases are formed on the CIGS surface, which allows K+ ions to be effectively substituted into Cu vacancies.
ABSTRACT
Dual-functional quantum-dots light emitting diodes (QLEDs) have been fabricated using solution processable vanadium oxide (V2O5) hole injection layer to control the carrier transport behavior. The device shows selectable functionalities of photo-detecting and light-emitting behaviors according to the different operating voltage conditions. The device emitted a bright green light at the wavelength of 536 nm, and with the maximum luminance of 31,668 cd/m2 in a forward bias of 8.6 V. Meanwhile, the device could operate as a photodetector in a reverse bias condition. The device was perfectly turned off in a reverse bias, while an increase of photocurrent was observed during the illumination of 520 nm wavelength light on the device. The interfacial electronic structure of the device prepared with different concentration V2O5 solution was measured in detail using x-ray and ultraviolet photoelectron spectroscopy. Both the highest occupied molecular orbital and the gap state levels were moved closer to the Fermi level, according to increase the concentration of V2O5 solution. The change of gap state position enables to fabricate a dual-functional QLEDs. Therefore, the device could operate both as a photodetector and as a light-emitting diode with different applied bias. The result suggests that QLEDs can be used as a photosensor and as a light-emitting diode for the future display industry.
ABSTRACT
The interfacial electronic structure between a W-doped In2O3 (IWO) transparent electrode and a V2O5 hole injection layer (HIL) has been investigated using ultraviolet photoelectron spectroscopy for high-performance and inorganic quantum-dot light-emitting diodes (QLEDs). Based on the interfacial electronic structure measurements, we found gap states in a V2O5 HIL at 1.0 eV below the Fermi level. Holes can be efficiently injected from the IWO electrode into poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,4'-(4-sec-butylphenyl)diphenylamine)] (TFB) through the gap states of V2O5, which was confirmed by the hole injection characteristics of a hole-only device. Therefore, conventional normal-structured QLEDs were fabricated on a glass substrate with the IWO transparent electrode and V2O5 HIL. The maximum luminance of the device was measured as 9443.5 cd m-2. Our result suggests that the IWO electrode and V2O5 HIL are a good combination for developing high-performance and inorganic QLEDs.
