ABSTRACT
Dual-frequency ultrasonic assisted photocatalysis (DUAP) was proposed to enhance the degradation efficiency of methylene blue (MB) solution. The influence of operational parameters, i.e., irradiation time, ultrasonic arrangement, TiO(2) concentration and power density, was studied. The results implied that the rapid degradation of MB solution was achieved in 18 min under DUAP with the dual frequencies of 20/40 kHz. Kinetic investigation of MB degradation for the DUAP process was conducted on the basis of first-order kinetic equation and the synergistic effect was assessed by examination of the apparent rate constant. The effect of ultrasonic arrangement was analyzed by comparison of the pressure amplitude of ultrasonic superposition field. The evolvement of intermediate products and the role of active species during DUAP were distinguished by UV-Vis spectra and the free radical scavenging experiment.
Subject(s)
Methylene Blue/chemistry , Sonication , Catalysis , Kinetics , Photochemical ProcessesABSTRACT
Silica xerogels were prepared by thermal drying wet gels in an electric oven (70 degrees C) after certain duration of ambient drying, and the relevant effect is investigated on the mesopore structures and surface fractal dimensions of the resultant xerogels. The silica gels were derived from a hydrochloric acid-catalyzed TEOS (tetraethylorthaosilicate) system, and both magnetic stirring and ultrasonic vibration were adopted during sol preparation. The percentage mesoporosity and surface fractal dimensions are evaluated using image analysis methods, based on FE-SEM (field emission gun-scanning electron microscopy) images. The results show that the mesoporosity of the resultant xerogels decreases with the duration of ambient drying for samples prepared using magnetic stirring and low-intensity ultrasonic vibration, while samples subjected to high-intensity ultrasound show a somewhat reverse trend. Samples prepared with magnetic stirring have almost constant surface fractal dimensions (nearly 3), irrespective of the ambient drying before thermal drying. The surface fractal dimensions of samples prepared using ultrasound increase with the duration of ambient drying.
ABSTRACT
The effect of antimony concentration (C(Sb)/mass%) on the surface tension of molten silicon has been determined with the sessile drop method in the temperature range from 1693 to 1773 K and in the range of the oxygen partial pressure, Po(2), in an Ar atmosphere from 10(-23) to 10(-21) MPa. The results show that the surface tension of molten silicon decreases with increasing Sb concentration in the range of C(Sb)<0.9 mass%, which indicates positive adsorption of Sb in molten silicon and can be fairly described with the Szyszkowski's equation. The maximum decrease rate of surface tension is about 65 mN m(-1) (mass% C(Sb))(-1), and the temperature coefficient of surface tension, (partial differential sigma/ partial differential T)C(Sb), increases with increasing C(Sb). The evaporation of the systems was only observed between the melting points of antimony (904 K) and silicon (1683 K), and the surface tension presents no dependence on measuring time above the melting point of silicon.
ABSTRACT
The local corrosion of magnesia-chrome refractories containing MgO-Al(2)O(3) spinel has been investigated near the slag-metal interface by immersion tests. The local corrosion extent near the slag-metal interface was found to decrease with the increase of FeO, MgO, and Al(2)O(3) contents in the slag. The local corrosion depths in the diagonal direction on the cross sections of the square prism specimens were always 2 times those in the normal direction of the lateral faces, and the cross sections maintained their initial square shape during whole the corrosion duration. The local corrosion is reckoned to be driven by the Marangori convection, which accelerated the mass transfer of the components dissolved from the refractories.
ABSTRACT
The surface tension of molten tin has been determined by the sessile drop method at temperatures ranging from 523 to 1033 K and in the oxygen partial pressure (P(O(2))) range from 2.85 x 10(-19) to 8.56 x 10(-6) MPa, and its dependence on temperature and oxygen partial pressure has been analyzed. At P(O(2))=2.85 x 10(-19) and 1.06 x 10(-15) MPa, the surface tension decreases linearly with the increase of temperature and its temperature coefficients are -0.151 and -0.094 mN m(-1) K(-1), respectively. However, at high P(O(2)) (3.17 x 10(-10), 8.56 x 10(-6) MPa), the surface tension increases with the temperature near the melting point (505 K) and decreases above 723 K. The surface tension decrease with increasing P(O(2)) is much larger near the melting point than at temperatures above 823 K. The contact angle between the molten tin and the alumina substrate is 158-173 degrees, and the wettability is poor.
