ABSTRACT
This work presents the effect of surface roughness (Al 7075) on the microstructure and mechanical properties of cold-sprayed nickel coatings. Coating analysis included substrate surfaces and coating geometry, microstructure characterization, microhardness, nanohardness, elastic modulus, and adhesion. The results show that the surface preparation had a significant effect on coating adhesion and microstructure. The coating deposited at the highest gas temperature revealed a dense microstructure, showing very good adhesion of the impacting powder particles to the substrate and good bonding between deposited layers. The Ni grains with different shapes (elongated, equiaxed) and sizes of a few dozen to several hundred nanometres were present in the splats. An increase in temperature caused significant growth in coating thickness as a result of the powder grains' higher velocity. Moreover, higher gas temperature resulted in the enhancement of micro- and nanohardness, elastic modulus, and adhesion. The adhesive bond strength of Ni coatings in the tested temperature ranges from 500 °C to 800 °C increased with the increase in the surface roughness of the substrate. For the Al 7075 coarse grit-blasted (CG) substrate with the highest roughness, the adhesion reached the highest value of 44.6 MPa when the working gas was at a temperature of 800 °C. There were no distinct dependencies of surface roughness and thickness on the mechanical properties of the cold-sprayed nickel coating.
ABSTRACT
Additive manufacturing (AM) has seen remarkable development in recent years due to relatively high efficiency of the process. Cold spraying (CS) is a particular method of AM, in which titanium and titanium alloy powders are used. CS is a very competitive technology enabling the deposition of coatings, repairing machine parts, and manufacturing new components. For specific applications, the surface of cold-sprayed materials may require further processing. This paper reports an attempt to employ laser surface treatment (LST) of cold-sprayed coatings on an aluminium alloy substrate. The influence of laser beam interaction time on the coatings' properties was analysed. The microstructure was investigated and observed employing scanning electron microscopy (SEM). To evaluate residual stress after CS and LST, the sin2ψ technique was used. Investigations were also performed on Vickers hardness, contact angle, and surface roughness. Significant changes in the surface morphology of the coatings and elevated residual stress levels dependent on the laser beam interaction time were observed. Increased Vickers hardness was recorded for titanium alloy Ti6Al4V. LST also led to increased surface hydrophilicity of the modified materials Ti and Ti6Al4V.
ABSTRACT
Aluminium (Al) and titanium (Ti) coatings were applied on AZ91E magnesium alloy using a low-pressure warm spray (WS) method. The deposition was completed using three different nitrogen flow rates (NFR) for both coatings. NFR effects on coating microstructure and other physical properties were systematically studied. Microstructural characterization was performed using scanning electron microscopy (SEM), and the porosity was estimated using two methods-image analysis and X-ray microtomography. The coating adhesion strength, wear resistance, and hardness were examined. The protective properties of the coatings were verified via a salt spray test. Decreasing NFR during coating deposition produced more dense and compact coatings. However, these conditions increased the oxidation of the powder. Al coatings showed lower hardness and wear resistance than Ti coatings, although they are more suitable for corrosion protection due to their low porosity and high compactness.
ABSTRACT
In this work, the effect of the substrate, Al 7075 alloy and 1H18NT9 stainless steel, on the microstructure and tribological properties of cold sprayed (Cr3C2-25(Ni20Cr))-(Ni-graphite) coatings was investigated. Both coatings were dense and did not reveal any discontinuities at the interfaces. They had similar Cr3C2 and graphite contents. Their microstructures showed a variety of grain sizes of the matrix phase between the inner part of the splat, showing large ones, and their boundaries, where elongated and nanostructured grains were formed during the deposition process. The coating deposited on the steel substrate revealed a slightly higher hardness and lower abrasive wear with the Al2O3 loose abrasive particles. The force required to destroy the durability of the coating-steel substrate system in the three-point bending test was higher than those of the other ones. The cermet deposit cold sprayed on steel and examined at 25 °C under 10 N revealed the best wear resistance and the lowest friction coefficient.
ABSTRACT
INTRODUCTION: Implantable cardioverter defibrillators register various types of arrhythmias. Thus they can be exploited to better identify patients with atrial fibrillation episodes and increase the proportion of patients who may benefit from implementation of pharmacological prophylaxis of thromboembolic events, most of which are asymptomatic. The aim of the study was to assess of the frequency, symptoms and predisposing factors for the occurrence of atrial fibrillation episodes in patients with an implanted implantable cardioverter defibrillator (ICD) and cardiac resynchronisation therapy with defibrillator (CRT-D) based on the analysis of intracardiac electrocardiograms (EGM/IEGM) records. MATERIAL AND METHODS: The study included 174 consecutive outpatients with heart failure, sinus rhythm and an implanted cardioverter defibrillator and cardiac resynchronisation therapy with defibrillator. Follow-up visits with analysis of IEGM records occurred every 3 months. During a mean follow-up of 20 months, 901 visits were carried out. One hundred forty-seven patients had at least 1 year of follow-up. RESULTS: Atrial fibrillation episodes in the study group occurred in 54 (31.0%) patients and 71.4% were asymptomatic. Predisposing factors were: history of paroxysmal atrial fibrillation (37.0% vs. 13.3%, p < 0.001), atrioventricular conduction abnormalities (42.6% vs. 20.0%, p = 0.002), intraventricular conduction abnormalities (59.3% vs. 40.8%, p = 0.02) and more severe mitral regurgitation (7.4% vs. 0.8%, p = 0.04). Chronic renal disease was a risk factor for death in the study group. No stroke occurred during the study. CONCLUSIONS: Episodes of paroxysmal atrial fibrillation in patients with systolic heart failure and implanted cardioverter-defibrillator systems are quite common. The majority of the episodes recorded in the study were asymptomatic.
ABSTRACT
In this research, the cold spray process as an additive manufacturing method was applied to deposit thick titanium coatings onto 7075 aluminium alloy. An analysis of changes in the microstructure and mechanical properties of the coatings depending on the standoff distance was carried out to obtain the maximum deposition efficiency. The process parameters were selected in such a way as to ensure the spraying of irregular titanium powder at the highest velocity and temperature and changing the standoff distance from 20 to 100 mm. Experimental studies demonstrated that the standoff distance had a significant effect on the microstructure of the coatings and their adhesion. Moreover, its rise significantly increased the deposition efficiency. The standoff distance also significantly affected the coating microstructure and their adhesion to the substrate, but did not cause any changes in their phase composition. The standoff distance also influenced the coating porosity, which first decreased to a minimum level of 0.2% and then increased significantly to 9.8%. At the same time, the hardness of the coatings increased by 30%. Numerical simulations confirmed the results of the tests.
ABSTRACT
The influence of the laser treatment on the corrosion resistance of the Cr3C2-25(Ni20Cr) cermet coating on the Al7075 (EN, AW-7075) substrate (Cr3C2-25(Ni20Cr)/Al7075) was investigated. The coating was produced by the cold sprayed (CS) method. The tested coatings were irradiated with a laser spot speed of 600 mm/min, 800 mm/min, and 1000 mm/min. The mechanical properties of the Cr3C2-25(Ni20Cr)/Al7075 were characterized by microhardness (HV) measurements. The surface and microstructure of the specimens were observed by ascanning electron microscope (SEM) and other assistive techniques. The corrosion test of materials wascarried out by using the electrochemical method in the acidic chloride solution. Cermet coatings perfectly protect the Al7075 substrate against contact with an aggressive corrosion environment. The laser remelting process of the Cr3C2-25(Ni20Cr) layer caused the homogenization of the structure cermet coatings. The irradiation with the laser beam eliminates microcracks and pores on the Cr3C2-25(Ni20Cr) surface. However, the best effect of improving the anti-corrosion properties of cermet coating was obtained for the lowest laser spot speed (i.e., 600 mm/min). It was found that the corrosion rate of the Cr3C2-25(Ni20Cr) cermet coating was reduced by more than two times compared to the highest speed of the laser spot.
ABSTRACT
This study analyzed the mechanical properties of cold-sprayed Cr3C2-25(Ni20Cr) blended with Ni-graphite as a solid lubricant deposited on 7075 aluminum alloy substrate. To optimize the coating properties, different sets of parameters (graphite content in feedstock, process gas composition, spraying distance, and traverse gun speed) were tested in the frame of the Taguchi experiment. The cold-sprayed coatings were evaluated for their chromium carbide and graphite content, hardness, and coefficient of friction. Analysis of the microstructure of the deposited coatings revealed that graphite as a soft and brittle component fills all voids in the coating and its quantity depends on its content in the feedstock. The experimental results show that the composition of the process gas has the greatest impact on the Cr3C2 content in the coating and the proportion of graphite in the sprayed blend directly affects its hardness. In the case of the coefficient of friction, the most significant parameters were the graphite content in the sprayed blend, the spraying distance, and process gas composition. The conducted verification experiment with the optimum parameter values allowed a coating with the highest hardness and the lowest coefficient of friction to be obtained.
ABSTRACT
BACKGROUND: The research involved the evaluation of physical and mechanical properties of hydroxyapatite (HAp) bio-ceramics sprayed on titanium substrate of the type Ti-grade 2 (CP-Ti) by means of the plasma method. An innovative method of coating is applied when using implantology for healing bone defects in the body. MATERIAL AND METHODS: Hydroxyapatite coating was prepared in order to conduct research. The powder was made using wet-chemical technology consisting in separating the solids from the solution. Next, a titanium substrate was prepared, onto which hydroxyapatite was applied with a plasma technique. RESULTS: As a result of the research it has to be noted that the properties of the obtained coating may be used for covering large surfaces of implants of any shape. CONCLUSIONS: During the research into the physical and mechanical properties of hydroxyapatite composites it has been observed that they show sufficient mechanical properties to be used in implantology. The further aim of the research will involve selecting technological parameters of spray coating in order to increase adhesion and cohesion of HAp coatings. Med Pr 2018;69(6):651-661.
