Fabrication and characterization of dual-layer hollow fibre membranes incorporating poly(citric acid)-grafted GO with enhanced antifouling properties for water treatment.

Membrane fouling during the filtration process is a perennial issue and could lead to reduced separation efficiency. In this work, poly(citric acid)-grafted graphene oxide (PGO) was incorporated into a matrix of single-layer hollow fibre (SLHF) and dual-layer hollow fibrr (DLHF) membranes, respectively, aiming to improve membrane antifouling properties during water treatment. Different loadings of PGO ranging from 0 to 1 wt% were first introduced into the SLHF to identify the best PGO loading for the DLHF preparation with its outer layer modified by nanomaterials. The findings showed that at the optimized PGO loading of 0.7 wt%, the resultant SLHF membrane could achieve higher water permeability and bovine serum albumin rejection compared to the neat SLHF membrane. This is due to the improved surface hydrophilicity and increased structural porosity upon incorporation of optimized PGO loading. When 0.7 wt% PGO was introduced only to the outer layer of DLHF, the cross-sectional matrix of the membrane was altered, forming microvoids and spongy-like structures (more porous). Nevertheless, the BSA rejection of the membrane was improved to 97.7% owing to an inner selectivity layer produced from a different dope solution (without the PGO). The DLHF membrane also demonstrated significantly higher antifouling properties than the neat SLHF membrane. Its flux recovery rate is 85%, i.e. 37% better than that of a neat membrane. By incorporating hydrophilic PGO into the membrane, the interaction of the hydrophobic foulants with the membrane surface is greatly reduced.

Dialysis Membranes for Acute Kidney Injury.

Mortality and morbidity rates among critically ill septic patients having acute kidney injury (AKI) are very high, considering the total number of deaths after their admission. Inappropriate selection of the type of continuous renal replacement therapy and inadequate therapy become the immediate causes of these issues. Dialysis is a commonly used treatment intended to prolong the life of AKI patients. Dialysis membranes, which are the core of dialysis treatment, must be properly selected to ensure fair treatment to the patients. The accumulation of certain types of molecules must be dealt with using the right membrane. Whether it is low-flux, high-flux, or adsorptive type, the dialysis membrane should be chosen depending on the condition of the patients. The selection of dialysis membranes should also be based on their effect on the treatment outcomes and well-being. All these options are needed to serve the patients of different clinical settings. The use of dialysis membranes is not restricted to conventional haemodialysis, but rather they can be employed in haemoperfusion, haemofiltration, haemodiafiltration, or a combination of any two of them. This review focuses in-depth on different types of dialysis membranes, their characteristics, and approaches in addressing the issues encountered in patients having AKI with sepsis and/or multiorgan failure in intensive care units.

Fouling Prevention in Polymeric Membranes by Radiation Induced Graft Copolymerization.

The application of membrane processes in various fields has now undergone accelerated developments, despite the presence of some hurdles impacting the process efficiency. Fouling is arguably the main hindrance for a wider implementation of polymeric membranes, particularly in pressure-driven membrane processes, causing higher costs of energy, operation, and maintenance. Radiation induced graft copolymerization (RIGC) is a powerful versatile technique for covalently imparting selected chemical functionalities to membranes' surfaces, providing a potential solution to fouling problems. This article aims to systematically review the progress in modifications of polymeric membranes by RIGC of polar monomers onto membranes using various low- and high-energy radiation sources (UV, plasma, γ-rays, and electron beam) for fouling prevention. The feasibility of the modification method with respect to physico-chemical and antifouling properties of the membrane is discussed. Furthermore, the major challenges to the modified membranes in terms of sustainability are outlined and the future research directions are also highlighted. It is expected that this review would attract the attention of membrane developers, users, researchers, and scientists to appreciate the merits of using RIGC for modifying polymeric membranes to mitigate the fouling issue, increase membrane lifespan, and enhance the membrane system efficiency.

Nanocrystalline cellulose incorporated biopolymer tailored polyethersulfone mixed matrix membranes for efficient treatment of produced water.

Membrane technology is a sustainable method to remove pollutants from petroleum wastewater. However, the presence of hydrophobic oil molecules and inorganic constituents can cause membrane fouling. Biomass derived biopolymers are promising renewable materials for membrane modification. In this study, fouling resistant biopolymer N-phthaloylchitosan (CS)- based polythersulfone (PES) mixed matrix membranes (MMMs) incorporated with nanocrystalline cellulose (NCC) was fabricated via phase inversion method and applied for produced water (PW) treatment. The morphological and Fourier-transform infrared spectroscopy (FTIR) analyses of the as-prepared NCC evidenced the formation of fibrous sheet-like structure and the presence of hydrophilic group. The membrane morphology and AFM analysis showed that the NCC altered the surface and cross-sectional morphology of the CS-PES MMMs. The tensile strength of NCC-CS-PES MMMs was also enhanced. 0.5 wt% NCC-CS-PES MMMs displayed a water permeability of 1.11 × 10-7 m/s.kPa with the lowest contact angle value of 61°. It affirmed that its hydrophilicity increased through the synergetic interaction between CS biopolymer and NCC. The effect of process variables such as transmembrane pressure (TMP) and synthetic produced water (PW) concentration were evaluated for both neat PES and NCC-CS-PES MMMs membranes. 0.5 wt% NCC-CS-PES MMMs exhibited the highest PW rejection of 98% when treating 50 mgL-1 of synthetic PW at a transmembrane pressure (TMP) of 200 kPa. The effect of nano silica and sodium chloride on the long-term PW filtration of NCC-CS-PES MMMs was also investigated.

A Review of Commercial Developments and Recent Laboratory Research of Dialyzers and Membranes for Hemodialysis Application.

Dialyzers have been commercially used for hemodialysis application since the 1950s, but progress in improving their efficiencies has never stopped over the decades. This article aims to provide an up-to-date review on the commercial developments and recent laboratory research of dialyzers for hemodialysis application and to discuss the technical aspects of dialyzer development, including hollow fiber membrane materials, dialyzer design, sterilization processes and flow simulation. The technical challenges of dialyzers are also highlighted in this review, which discusses the research areas that need to be prioritized to further improve the properties of dialyzers, such as flux, biocompatibility, flow distribution and urea clearance rate. We hope this review article can provide insights to researchers in developing/designing an ideal dialyzer that can bring the best hemodialysis treatment outcomes to kidney disease patients.

Co-Adsorptive Removal of Creatinine and Urea by a Three-Component Dual-Layer Hollow Fiber Membrane.

The development of wearable artificial kidney demands an efficient dialysate recovery, which relies upon the adsorption process. This study proposes a solution to solve the problem of competitive adsorption between the uremic toxins by employing two adsorptive components in a membrane separation process. Dual-layer hollow fiber (DLHF) membranes, which are composed of a polysulfone (PSf)/activated carbon (AC) inner layer and a PSf/poly(methyl methacrylate) (PMMA) outer layer, were prepared for co-adsorptive removal of creatinine and urea from aqueous solution. The DLHF membranes were characterized in terms of morphological, physicochemical, water transport, and creatinine adsorption properties. The membrane was then subjected to an ultrafiltration adsorption study for performance evaluation. The incorporation of AC in membrane, as confirmed by microscopic and surface analyses, has improved the pure water flux up to 25.2 L/(m2 h). A membrane with optimum AC loading (9 wt %) demonstrated the highest maximum creatinine adsorption capacity (86.2 mg/g) based on the Langmuir adsorption isotherm model. In the ultrafiltration adsorption experiment, the membrane removed creatinine and urea with a combined average percent removal of 29.3%. Moreover, the membrane exhibited creatinine and urea uptake recoveries of 98.8 and 81.2%, respectively. The combined action of PMMA and AC in the PSf DLHF membrane has made the adsorption of multiple uremic toxins possible during dialysate recovery.