Influence of the loci of non-cavitated fissure caries on its detection with optical coherence tomography.

OBJECTIVE: The main objective of this study was to evaluate the accuracy of optical coherence tomography (OCT) in detecting naturally occurring non-cavitated fissure caries (NCFC) in totality and at different loci by visually assessing cross-sectional OCT scans (B-scan) with an interpretation criterion. The secondary objective was to evaluate the agreement between dimensions of NCFC measured with OCT and polarized light microscopy (PLM). METHODS: 71 investigation sites of sound fissure and naturally occurring NCFC on human extracted premolars were identified and scanned with a swept-source OCT. The teeth were then sectioned bucco-lingually at the investigation sites and imaged using PLM. Two calibrated examiners trained on the B-scan NCFC visual interpretation criteria established for this study, assessed the investigation sites and results were validated against PLM. RESULTS: Detection sensitivity of B-scan for NCFC when fissures were assessed in totality, or on the slopes or walls separately are 0.98, 0.95, 0.94 and specificity are 0.95, 0.90, and 0.95. One-way ANOVA showed that width measurements of wall loci done with OCT and PLM were not statistically different. However, OCT height measurements of slope loci were statistically bigger with a constant bias of 0.08 mm (of which is not clinically significant) and OCT height measurements of wall loci were statistically smaller (0.57 mm) and Bland-Altman plots indicated presence of proportionate bias. CONCLUSION: Visual assessment of B-scans with the interpretation criteria resulted in both high specificity and sensitivity and were not affected by loci location. OCT width measurement of wall loci is in agreement with PLM. CLINICAL SIGNIFICANCE: Unanimous high sensitivity in this and previous studies indicate that visual assessment of B-scans reliably rule out NCFC. Detection accuracy was not affected by loci location. Width of wall loci and/or height of slope loci in OCT B-scan are to be used for monitoring NCFC but not height of wall loci.

Measuring initial enamel erosion with quantitative light-induced fluorescence and optical coherence tomography: an in vitro validation study.

BACKGROUND: Measurement of initial enamel erosion is currently limited to in vitro methods. Optical coherence tomography (OCT) and quantitative light-induced fluorescence (QLF) have been used clinically to study advanced erosion. Little is known about their potential on initial enamel erosion. OBJECTIVES: To evaluate the sensitivity of QLF and OCT in detecting initial dental erosion in vitro. METHODS: 12 human incisors were embedded in resin except for a window on the buccal surface. Bonding agent was applied to half of the window, creating an exposed and non-exposed area. Baseline measurements were taken with QLF, OCT and surface microhardness. Samples were immersed in orange juice for 60 min and measurements taken stepwise every 10 min. QLF was used to compare the loss of fluorescence between the two areas. The OCT system, OCS1300SS (Thorlabs Ltd.), was used to record the intensity of backscattered light of both areas. Multiple linear regression and paired t test were used to compare the change of the outcome measures. RESULTS: All 3 instruments demonstrated significant dose responses with the erosive challenge interval (p < 0.05) and a detection threshold of 10 min from baseline. Thereafter, surface microhardness demonstrated significant changes after every 10 min of erosion, QLF at 4 erosive intervals (20, 40, 50 and 60 min) while OCT at only 2 (50 and 60 min). CONCLUSION: It can be concluded that OCT and QLF were able to detect demineralization after 10 min of erosive challenge and could be used to monitor the progression of demineralization of initial enamel erosion in vitro.

In vitro performance of different methods in detecting occlusal caries lesions.

UNLABELLED: Early caries detection is essential for the implementation of preventive, therapeutic and intervention strategies within general dental practice. OBJECTIVE: The aim of this study was to compare the in vitro performance of the International Caries Detection and Assessment System (ICDAS), digital photographs scored with ICDAS (ICDAS photographs), fibre-optic transillumination (FOTI), optical coherence tomography (OCT), SoproLife(®) camera and two implementations of quantitative light-induced fluorescence a commercial (QLF-Inspektor Research systems) and a custom (QLF-Custom) system, to detect early and intermediate occlusal lesions. METHODS: One hundred and twelve permanent extracted teeth were selected and assessed with each detection method. Histological validation was used as a gold standard. The detection methods were compared by means of sensitivity, specificity, areas under receiver operating characteristic (AUROC) curves for enamel and dentine levels and with the Spearman's rank correlation coefficient against histology. RESULTS: For any enamel or dentine caries detection, the AUROC curves ranged from 0.86 (OCT) to 0.98 (ICDAS and ICDAS photographs, SoproLife(®) camera) and at the dentine level from 0.83 (OCT) to 0.96 for FOTI. The correlations with histology ranged between 0.65 (OCT) and 0.88 (ICDAS and FOTI). Under in vitro conditions, the assessed detection methods showed excellent intra-examiner reproducibility. All the methods were strongly correlated with histology (p<0.01) except OCT which showed a moderate correlation (0.65). CONCLUSION: Even though all methods present similar performance in detecting occlusal caries lesions, visual inspection seems to be sufficient to be used in clinical practice for detection and assessment of lesion depth. Other methods may be useful in monitoring caries lesion behaviour.

Occlusal caries detection by using thermal imaging.

OBJECTIVES: To explore the applicability of thermal changes associated with dehydration for the detection and quantification of early tooth decay on occlusal surfaces using infrared imaging. METHODS: A total of 72 sites on 25 human teeth with various degrees of natural demineralisation have been used. Continuous evaporation of water inside the pores by pressurised air-drying is used to produce a thermodynamic response on the tooth surface. The temporal profile of the temperature will depend on the amount of water at each position and this is studied in relation to the degree of porosity and the lesion severity. The area enclosed by the time-temperature curve, DeltaQ, was then used for quantification of the lesion. RESULTS: Maps of DeltaQ were obtained and histological examinations were performed for all teeth. A detection sensitivity of 77% and specificity of 87% for areas that are either sound or have a histological E1 lesion, 87% and 72% for areas that have either an E2 or EDJ lesion, and 58% and 83% for areas that have a lesion reaching the dentin was found using this method. CONCLUSIONS: Thermal imaging shows the ability to discriminate, in vitro, between (a) either areas that are sound or with a lesion on the outer half of the enamel and (b) areas with a lesion extending to the middle of the enamel or deeper. However, variations of the temperature in an open mouth and humidity due to respiration can potentially challenge the ability of using this technique in vivo and this requires further investigation.