Giant Electromechanical Effect in Piezoelectric Nanomembranes Based on Hf0.5Zr0.5O2.

Since ultrathin ferroelectric HfO2 films can be conformally grown by atomic layer deposition even on complex three-dimensional structures, new horizons in the development of next-generation piezoelectric devices are opened. However, hafnium oxide has a significant drawback for piezoelectric applications: its piezoelectric coefficients are much smaller than those of classical materials currently used in piezoelectric devices. Therefore, new approaches to the development of high-performance piezoelectric devices based on exploiting the unique properties of HfO2 are of paramount importance. In this work, a giant electromechanical effect in miniature piezoelectric membrane devices based on a 10 nm-thick ferroelectric Hf0.5Zr0.5O2 (HZO) film is experimentally demonstrated. Compared to the pure piezoelectric effect in the HZO film, the gain of the electromechanical response in membrane devices reaches 25 times. Numerical simulations confirm that this effect stems from the asymmetric shape of the membranes and can be further improved by designing the device geometry. Furthermore, according to first-principles calculations, an additional opportunity to improve the piezoelectric coefficient, and hence, the device efficiency is provided by the engineering of the mechanical stress in the HZO film. The proposed approach enables the development of new promising piezoelectric devices including miniature reflectors, nanoactuators, and nanoswitches.

Retention Improvement of HZO-Based Ferroelectric Capacitors with TiO2 Insets.

The influence of the bottom TiO2 interfacial layer grown by atomic layer deposition on the ferroelectric properties of the TiN/Hf0.5Zr0.5O2/TiN capacitors is systematically investigated. We show that the integration of the TiO2 layer leads to an increase in the polar orthorhombic phase content in the Hf0.5Zr0.5O2 film. In addition, the crystalline structure of the Hf0.5Zr0.5O2 film is highly dependent on the thickness of the TiO2 inset, with monoclinic phase stabilization after the increase of TiO2 thickness. Special attention in this work is given to the key reliability parameters-retention and endurance. We demonstrate that the integration of the TiO2 inset induces valuable retention improvement. Using a novel approach to the depolarization measurements, we show that the depolarization contribution to the retention loss is insignificant, which leaves the imprint effect as the root of the retention loss in TiN/TiO2/Hf0.5Zr0.5O2/TiN devices. We believe that the integration of the insulator interfacial layer suppresses the scavenging effect from the bottom TiN electrode, leading to a decrease in the oxygen vacancy content in the Hf0.5Zr0.5O2 film, which is the main reason for imprint mitigation. At the same time, although the observed retention improvement is very promising for the upcoming technological integration, the field cycling testing revealed the endurance limitations linked to the phase transitions in the TiO2 layer and the rise of the effective electric field applied to the Hf0.5Zr0.5O2 film.

Nanoparticle-Doped Hybrid Polyelectrolyte Microcapsules with Controlled Photoluminescence for Potential Bioimaging Applications.

Fluorescent imaging is widely used in the diagnosis and tracking of the distribution, interaction, and transformation processes at molecular, cellular, and tissue levels. To be detectable, delivery systems should exhibit a strong and bright fluorescence. Quantum dots (QDs) are highly photostable fluorescent semiconductor nanocrystals with wide absorption spectra and narrow, size-tunable emission spectra, which make them suitable fluorescent nanolabels to be embedded into microparticles used as bioimaging and theranostic agents. The layer-by-layer deposition approach allows the entrapping of QDs, resulting in bright fluorescent microcapsules with tunable surface charge, size, rigidity, and functional properties. Here, we report on the engineering and validation of the structural and photoluminescent characteristics of nanoparticle-doped hybrid microcapsules assembled by the deposition of alternating oppositely charged polyelectrolytes, water-soluble PEGylated core/shell QDs with a cadmium selenide core and a zinc sulfide shell (CdSe/ZnS), and carboxylated magnetic nanoparticles (MNPs) onto calcium carbonate microtemplates. The results demonstrate the efficiency of the layer-by-layer approach to designing QD-, MNP-doped microcapsules with controlled photoluminescence properties, and pave the way for the further development of next-generation bioimaging agents based on hybrid materials for continuous fluorescence imaging.

Magnetoelectric Coupling at the Ni/Hf0.5Zr0.5O2 Interface.

Composite multiferroics containing ferroelectric and ferromagnetic components often have much larger magnetoelectric coupling compared to their single-phase counterparts. Doped or alloyed HfO2-based ferroelectrics may serve as a promising component in composite multiferroic structures potentially feasible for technological applications. Recently, a strong charge-mediated magnetoelectric coupling at the Ni/HfO2 interface has been predicted using density functional theory calculations. Here, we report on the experimental evidence of such magnetoelectric coupling at the Ni/Hf0.5Zr0.5O2(HZO) interface. Using a combination of operando XAS/XMCD and HAXPES/MCDAD techniques, we probe element-selectively the local magnetic properties at the Ni/HZO interface in functional Au/Co/Ni/HZO/W capacitors and demonstrate clear evidence of the ferroelectric polarization effect on the magnetic response of a nanometer-thick Ni marker layer. The observed magnetoelectric effect and the electronic band lineup of the Ni/HZO interface are interpreted based on the results of our theoretical modeling. It elucidates the critical role of an ultrathin NiO interlayer, which controls the sign of the magnetoelectric effect as well as provides a realistic band offset at the Ni/HZO interface, in agreement with the experiment. Our results hold promise for the use of ferroelectric HfO2-based composite multiferroics for the design of multifunctional devices compatible with modern semiconductor technology.

Controlling Charge Transfer from Quantum Dots to Polyelectrolyte Layers Extends Prospective Applications of Magneto-Optical Microcapsules.

The layer-by-layer (LbL) deposition approach allows combined incorporation of fluorescent, magnetic, and plasmonic nanoparticles into the shell of polyelectrolyte microcapsules to obtain stimulus-responsive systems whose imaging and drug release functions can be triggered by external stimuli. The combined use of fluorescent quantum dots (QDs) and magnetic nanoparticles (MNPs) yields magnetic-field-driven imaging tools that can be tracked and imaged even deep in tissue when the appropriate type of QDs and wavelength of their excitation are used. QDs are excellent photonic labels for microcapsule encoding due to their close-to-unity photoluminescence (PL) quantum yields, narrow PL emission bands, and tremendous one- and two-photon extinction coefficients. However, the presence of MNPs and electrically charged polyelectrolyte molecules used for the LbL fabrication of magneto-optical microcapsules provokes alterations of the QD optical properties because of the photoinduced charge and energy transfer resulting in QD photodarkening or photobrightening. These lead to variation of the microcapsule PL signal under illumination, which hampers their tracking and quantitative analysis in cells and tissues. Here, we have studied the effects of the structure and spatial arrangement of the nanoparticles within the microcapsule polyelectrolyte shell, the total shell thickness, and the shell surface charge on their PL properties under continuous illumination. The roles of the charge transfer and its main driving forces in the stability of the microcapsules PL signal have been established, and the design of the microcapsules dually encoded with QDs and MNPs providing the strongest and most stable PL has been determined. Controlling the energy transfer from the QDs and MNPs and the charge transfer from QDs to polyelectrolyte layers in the engineering of magneto-optical microcapsules with a bright and stable PL signal extends their applications to long-lasting quantitative fluorescence imaging.

On-Chip TaO x -Based Non-volatile Resistive Memory for in vitro Neurointerfaces.

The development of highly integrated electrophysiological devices working in direct contact with living neuron tissue opens new exciting prospects in the fields of neurophysiology and medicine, but imposes tight requirements on the power dissipated by electronics. On-chip preprocessing of neuronal signals can substantially decrease the power dissipated by external data interfaces, and the addition of embedded non-volatile memory would significantly improve the performance of a co-processor in real-time processing of the incoming information stream from the neuron tissue. Here, we evaluate the parameters of TaO x -based resistive switching (RS) memory devices produced by magnetron sputtering technique and integrated with the 180-nm CMOS field-effect transistors as possible candidates for on-chip memory in the hybrid neurointerface under development. The electrical parameters of the optimized one-transistor-one-resistor (1T-1R) devices, such as the switching voltage (approx. ±1 V), uniformity of the R off/R on ratio (∼10), read/write speed (<40 ns), and the number of the writing cycles (up to 1010), are satisfactory. The energy values for writing and reading out a bit ∼30 and ∼0.1 pJ, respectively, are also suitable for the desired in vitro neurointerfaces, but are still far too high once the prospective in vivo applications are considered. Challenges arising in the course of the prospective fabrication of the proposed TaO x -based RS devices in the back-end-of-line process are identified.

Polarization-dependent electric potential distribution across nanoscale ferroelectric Hf0.5Zr0.5O2 in functional memory capacitors.

The emergence of ferroelectricity in nanometer-thick films of doped hafnium oxide (HfO2) makes this material a promising candidate for use in Si-compatible non-volatile memory devices. The switchable polarization of ferroelectric HfO2 controls functional properties of these devices through the electric potential distribution across the capacitor. The experimental characterization of the local electric potential at the nanoscale has not so far been realized in practice. Here, we develop a new methodology which allows us, for the first time, to experimentally quantify the polarization-dependent potential profile across few-nanometer-thick ferroelectric Hf0.5Zr0.5O2 thin films. Using a standing-wave excitation mode in synchrotron based hard X-ray photoemission spectroscopy, we depth-selectively probe TiN/Hf0.5Zr0.5O2/W prototype memory capacitors and determine the local electrostatic potential by analyzing the core-level line shifts. We find that the electric potential profile across the Hf0.5Zr0.5O2 layer is non-linear and changes with in situ polarization switching. Combined with our scanning transmission electron microscopy data and theoretical modeling, we interpret the observed non-linear potential behavior in terms of defects in Hf0.5Zr0.5O2, at both interfaces, and their charge state modulated by the ferroelectric polarization. Our results provide an important insight into the intrinsic electronic properties of HfO2 based ferroelectric capacitors and are essential for engineering memory devices.

Ferroelectric Second-Order Memristor.

While the conductance of a first-order memristor is defined entirely by the external stimuli, in the second-order memristor it is governed by the both the external stimuli and its instant internal state. As a result, the dynamics of such devices allows to naturally emulate the temporal behavior of biological synapses, which encodes the spike timing information in synaptic weights. Here, we demonstrate a new type of second-order memristor functionality in the ferroelectric HfO2-based tunnel junction on silicon. The continuous change of conductance in the p+-Si/Hf0.5Zr0.5O2/TiN tunnel junction is achieved via the gradual switching of polarization in ferroelectric domains of polycrystalline Hf0.5Zr0.5O2 layer, whereas the combined dynamics of the built-in electric field and charge trapping/detrapping at the defect states at the bottom Si interface defines the temporal behavior of the memristor device, similar to synapses in biological systems. The implemented ferroelectric second-order memristor exhibits various synaptic functionalities, such as paired-pulse potentiation/depression and spike-rate-dependent plasticity, and can serve as a building block for the development of neuromorphic computing architectures.

Ferroelectricity in Hf0.5Zr0.5O2 Thin Films: A Microscopic Study of the Polarization Switching Phenomenon and Field-Induced Phase Transformations.

Because of their full compatibility with the modern Si-based technology, the HfO2-based ferroelectric films have recently emerged as viable candidates for application in nonvolatile memory devices. However, despite significant efforts, the mechanism of the polarization switching in this material is still under debate. In this work, we elucidate the microscopic nature of the polarization switching process in functional Hf0.5Zr0.5O2-based ferroelectric capacitors during its operation. In particular, the static domain structure and its switching dynamics following the application of the external electric field have been monitored with the advanced piezoresponse force microscopy (PFM) technique providing a nm resolution. Separate domains with strong built-in electric field have been found. Piezoresponse mapping of pristine Hf0.5Zr0.5O2 films revealed the mixture of polar phase grains and regions with low piezoresponse as well as the continuum of polarization orientations in the grains of polar orthorhombic phase. PFM data combined with the structural analysis of pristine versus trained film by plan-view transmission electron microscopy both speak in support of a monoclinic-to-orthorhombic phase transition in ferroelectric Hf0.5Zr0.5O2 layer during the wake-up process under an electrical stress.

Effect of Polarization Reversal in Ferroelectric TiN/Hf0.5Zr0.5O2/TiN Devices on Electronic Conditions at Interfaces Studied in Operando by Hard X-ray Photoemission Spectroscopy.

Because of their compatibility with modern Si-based technology, HfO2-based ferroelectric films have recently attracted attention as strong candidates for applications in memory devices, in particular, ferroelectric field-effect transistors or ferroelectric tunnel junctions. A key property defining the functionality of these devices is the polarization dependent change of the electronic band alignment at the metal/ferroelectric interface. Here, we report on the effect of polarization reversal in functional ferroelectric TiN/Hf0.5Zr0.5O2/TiN capacitors on the potential distribution across the stack and the electronic band line-up at the interfaces studied in operando by hard X-ray photoemission spectroscopy. By tracking changes in the position of Hf0.5Zr0.5O2 core-level lines with respect to those of the TiN electrode in both short- and open-circuit configurations following in situ polarization reversal, we derive the conduction band offset to be 0.7 (1.0) eV at the top and 1.7 (1.0) eV at the bottom interfaces for polarization, pointing up (down), respectively. Energy dispersive X-ray spectroscopy profiling of the sample cross-section in combination with the laboratory X-ray photoelectron spectroscopy reveal the presence of a TiOx/TiON layer at  both interfaces. The observed asymmetry in the band line-up changes in the TiN/Hf0.5Zr0.5O2/TiN memory stack is explained by different origin of these oxidized layers and effective pinning of polarization at the top interface. The described methodology and first experimental results are useful for the optimization of HfO2-based ferroelectric memory devices under development.

Ultrathin Hf0.5Zr0.5O2 Ferroelectric Films on Si.

Because of their immense scalability and manufacturability potential, the HfO2-based ferroelectric films attract significant attention as strong candidates for application in ferroelectric memories and related electronic devices. Here, we report the ferroelectric behavior of ultrathin Hf0.5Zr0.5O2 films, with the thickness of just 2.5 nm, which makes them suitable for use in ferroelectric tunnel junctions, thereby further expanding the area of their practical application. Transmission electron microscopy and electron diffraction analysis of the films grown on highly doped Si substrates confirms formation of the fully crystalline non-centrosymmetric orthorhombic phase responsible for ferroelectricity in Hf0.5Zr0.5O2. Piezoresponse force microscopy and pulsed switching testing performed on the deposited top TiN electrodes provide further evidence of the ferroelectric behavior of the Hf0.5Zr0.5O2 films. The electronic band lineup at the top TiN/Hf0.5Zr0.5O2 interface and band bending at the adjacent n(+)-Si bottom layer attributed to the polarization charges in Hf0.5Zr0.5O2 have been determined using in situ X-ray photoelectron spectroscopy analysis. The obtained results represent a significant step toward the experimental implementation of Si-based ferroelectric tunnel junctions.