CH4, C2H6, and CO2 Multi-Gas Sensing Based on Portable Mid-Infrared Spectroscopy and PCA-BP Algorithm.

A multi-gas sensing system was developed based on the detection principle of the non-dispersive infrared (NDIR) method, which used a broad-spectra light source, a tunable Fabry-Pérot (FP) filter detector, and a flexible low-loss infrared waveguide as an absorption cell. CH4, C2H6, and CO2 gases were detected by the system. The concentration of CO2 could be detected directly, and the concentrations of CH4 and C2H6 were detected using a PCA-BP neural network algorithm because of the interference of CH4 and C2H6. The detection limits were achieved to be 2.59 ppm, 926 ppb, and 114 ppb for CH4, C2H6, and CO2 with an averaging time of 429 s, 462 s, and 297 s, respectively. The root mean square error of prediction (RMSEP) of CH4 and C2H6 were 10.97 ppm and 2.00 ppm, respectively. The proposed system and method take full advantage of the multi-component gas measurement capability of the mid-infrared broadband source and achieve a compromise between performance and system cost.

Design, fabrication, and characterization of a single-polarization single-mode flexible hollow waveguide for low loss millimeter wave propagation.

A flexible metallic waveguide with elliptical core that achieves single-polarization single-mode (SPSM) propagation at millimeter wave was designed, fabricated, and characterized. In order to achieve SPSM propagation, optimization of the lengths of major/minor axes of elliptical core was conducted to cut off one of the two orthogonally polarized fundamental modes and all high-order modes. A one-meter long hollow elliptical waveguide (HEW) with major/minor axis length of 1.5/2.7 mm was fabricated. The substrate tube was a flexible elliptical polycarbonate (PC) tube, which was fabricated through glass-draw technique. Silver film was then coated on the inner surface of the tube. Simulation results show that the 1.5/2.7 mm HEW maintains SPSM propagation in the frequency band from 66.5 to 114 GHz. The SPSM operation was experimentally discussed in detail at 100 GHz. The measured loss of 2.58 dB/m and the output polarization ratio of 99.9% was obtained after propagating one meter. Furthermore, the waveguide was robust to bending and twisting. The additional loss was as small as 0.2 dB/m even when the waveguide was coiled into a circle. The potential application of HEWs as polarizers was demonstrated by using a 10 cm long waveguide for polarization detection and extinction ratio of 22.3 dB was achieved at 100 GHz.

Transmission and imaging characteristics of flexible gradually tapered waveguide at 0.3 THz.

Flexible gradually tapered metal waveguides (GTMWs) are fabricated by an inner plating silver film in a polycarbonate (PC) capillary for the transmission and imaging at 0.3 THz. It was demonstrated theoretically and experimentally that GTMWs have lower transmission losses and smaller additional losses of bending, comparing with thin constant bore metal waveguides (CBMWs). Measured losses of 1.95 dB and 2.45 dB were obtained for a 1 m long GTMW with bore size varying from 2.6 mm to 1.6 mm under straight and one circle bending configuration. Measured losses were 4.48 dB/m and 7.78 dB/m for 1.6 mm bore CBMW under the same straight and bend configurations. Owing to higher energy concentration at the output, a larger penetration ability of output wave can be achieved by GTMW, which is beneficial for imaging application. A scanning imaging system was established using fabricated waveguides as the probes. Measured results show that the air slits of the order of wavelength can be clearly distinguished. An imaging system with a GTMW probe also has better performances due to lower bending loss and improved coupling efficiency.