An advanced treatment process for 3-high wastewater discharged from crude oil storage tanks.

The wastewater discharged from crude oil storage tanks (WCOST) contains high concentrations of salt and metal iron ions, and high chemical oxygen demand (COD). It belongs to "3-high" wastewater, which is difficult for purification. In this study, WCOST treatments were comparatively investigated via an advanced pretreatment and the traditional coagulation-microfiltration (CMF) processes. After WCOST was purified through the conventional CMF process, fouling occurred in the microfiltration (MF) membrane, which is rather harmful to the following reverse osmosis (RO) membrane unit, and the effluent featured high COD and UV254 values. The analysis confirmed that the MF fouling was due to the oxidation of ferrous ions, and the high COD and UV254 values were mainly attributable to the organic compounds with small molecular sizes, including aromatic-like and fulvic-like compounds. After the pretreatment of the advanced process consisting of aeration, manganese sand filtration, and activated carbon adsorption in combination with CMF process, the removal efficiencies of organic matter and total iron ions reached 97.3% and 99.8%, respectively. All the water indexes of the effluent, after treatment by the advanced multi-unit process, meet well the corresponding standard. The advanced pretreatment process reported herein displayed a great potential for alleviating the MF membrane fouling and enhanced the lifetime of the RO membrane system in the 3-high WCOST treatment.

Study on the treatment of sulfite wastewater by Desulfovibrio.

In the wet flue gas desulfurization (WFGD) process, SO2 is adsorbed by alkaline liquor to produce alkaline wastewater containing sulfate and sulfite. Although the traditional chemical treatment method can achieve a high removal rate, it consumes a large number of chemicals and yields a large number of low-value by-products. The biological treatment process is a greener and more environmentally friendly treatment method. The current work studies microbial flue gas desulfurization directly using sulfite as the electron acceptor in the reduction process. Desulfovibrio were obtained by isolation and purification, and their growth conditions in sulfite wastewater and desulfurization process conditions were investigated by intermittent and continuous experiments. The results of intermittent experiments indicated that the optimal growth conditions of Desulfovibrio were a temperature of 38 °C, a pH value of 8.0, a COD/SO32- of 2 and that the growth of bacteria would be inhibited at a pH above 9.0 or below 7.3. Furthermore, Desulfovibrio could grow in simulated wastewater with a high SO32- concentration of 8000 mg/L. The results of continuous experiments showed that the removal of sulfite and the recovery of elemental sulfur was realized by a micro-oxygen depletion process, and the removal rate of sulfite of 99%, the yield of elemental sulfur is more than 80% and can reach 90% under the condition of low influent concentration. The bacteria grew well at a temperature of 40 °C and a pH value of the influent water of 7.5. To ensure the treatment effect, the hydraulic retention time (HRT) should be more than doubled for each 1000 mg/L increase in the influent sulfite concentration under the same reflux ratio. When the influent sulfite concentration was 1000 mg/L, 2000 mg/L, 3000 mg/L, and 4000 mg/L, the corresponding HRT was 3.01 h, 6.94 h, 17.4 h, and 31.9 h, respectively. The dominant species in the reactor was Desulfovibrio bacteria at 63.9% abundance. This study demonstrated the feasibility of using sulfite as an electron acceptor for microbial desulfurization, which can optimize the initial process and provide the possibility of treating high-concentration sulfite wastewater.

Investigation of the difference in color enhancement effect on cyanidin-3-O-glucoside by phenolic acids and the interaction mechanism.

Co-pigmentation effect of phenolic acids on cyanidin-3-O-glucoside (C3G) and the mechanisms were investigated. Sinapic acid (SIA), ferulic acid (FA), p-coumaric acid (p-CA) and syringic acid (SYA) significantly enhanced C3G stability (P < 0.05), whereas vanillic acid (VA) and gallic acid (GA) showed no influence (P > 0.05). Among these phenolic acids, SIA and FA had higher binding coefficient with C3G (48.83 and 43.38), reduced degradation rate constant by 40.0 âˆ¼ 50.0 %, prolonged half-life by 74.6 âˆ¼ 94.7 % at 323 K, and significantly inhibited C3G hydration reaction (pKh = 2.87 and 2.80, P < 0.05). Molecular docking revealed that C3G and co-pigments were connected by hydrogen bond and π-π stacking interaction. Hydroxycinnamic acids of SIA, FA and p-CA bound with ring B and ring C of C3G, while hydroxybenzoic acids of SYA, VA and GA hardly interacted with ring C. Generally, the protection effect of hydroxycinnamic acids on C3G was better than that of hydroxybenzoic acids, exhibiting stronger hyperchromic effect.

Recent advances in bioactive nanocrystal-stabilized Pickering emulsions: Fabrication, characterization, and biological assessment.

Numerous literatures have shown the advantages of Pickering emulsion (PE) for the delivery of bioactive ingredients in the fields of food, medicine, and cosmetics, among others. On this basis, the multi-loading mode of bioactives (internal phase encapsulation and/or loading at the interface) in small molecular bioactives nanocrystal-stabilized PE (BNC-PE) enables them higher loading efficiencies, controlled release, and synergistic or superimposed effects. Therefore, BNC-PE offers an efficacious delivery system. In this review, we briefly summarize BNC-PE fabrication and characterization, with a focus on the processes of possible evolution and absorption of differentially applied BNC-PE when interacting with the body. In addition, methods of monitoring changes and absorption of BNC-PE in vivo, from the nanomaterial perspective, are also introduced. The purpose of this review is to provide an accessible and comprehensive methodology for the characterization and evaluation of BNC-PE after formulation and preparation, especially in relation to biological assessment and detailed mechanisms throughout the absorption process of BNC-PE in vivo.