Scout-guided needle placement-a technical approach for dose reduction in CT-guided periradicular infiltration.

PURPOSE: To develop and evaluate a technical approach for CT-guided periradicular infiltration using quantitative needle access and guidance parameters extracted from CT scout images. METHODS: Five 3D-printed phantoms of the abdomen mimicking different patients were used to develop a technical approach for scout-guided periradicular infiltration. The needle access point, puncture depth, and needle angulation were calculated using measurements extracted from anterior-posterior and lateral CT scout images. Fifty needle placements were performed with the technique thus developed. Dose exposure and number of image acquisitions were compared with ten procedures performed using a conventional free-hand technique. Data were analyzed with the Mann-Whitney U test. RESULTS: Parameters derived solely from scout images provided adequate guidance for successful and reliable needle placement. Needle guidance was performed with the same equipment as the standard periradicular infiltration. Two scout images and 3.5 ± 2.3 (mean ± SD) single-shot images for needle positioning were acquired. Mean DLP ± SD was 3.8 ± 2.5 mGy cm. The number of single-shot acquisitions was reduced by 68% and the overall dose was reduced by 84% in comparison with the conventional free-hand technique (p < 0.0001). CONCLUSION: Scout-guided needle placement for periradicular infiltration is feasible and reduces radiation exposure significantly.

Characterization of office laser printers for 3-D printing of soft tissue CT phantoms.

The purpose of our study is to develop and evaluate a method for radiopaque 3-D printing (R3P) of soft tissue computed tomography (CT) phantoms with office laser printers. Five laser printers from different vendors are tested for toner CT attenuation. A liver phantom is created by printing CT images of a patient liver on office paper. One thousand eight hundred sixty paper sheets are printed with three repeated prints per page, resulting in a stack of 18.6 cm. The phantom is examined with 12 tube current settings. Images are reconstructed using filtered back projection (FBP) and iterative reconstruction [adaptive iterative dose reduction 3D (AIDR 3D)]. Seven radiologists rated image quality of all acquisitions. Toner attenuation of all investigated printers increased linearly with the print template grayscale. The liver phantom reproduced anatomic detail and attenuation values of the patient ( mean ± SD HU difference 12.68 ± 7.74 ). Image quality scores increased with dose but did not vary significantly above a threshold dose for AIDR 3D. Overall, AIDR 3D reconstructed images are rated superior to FBP reconstructions ( p < 0.001 ). In conclusion, R3P with standard office laser printers can generate soft tissue CT phantoms without hardware manipulations but with limited flexibility regarding attenuation properties of the printed toner material.

Paper-based 3D printing of anthropomorphic CT phantoms: Feasibility of two construction techniques.

OBJECTIVES: To develop and evaluate methods for assembling radiopaque printed paper sheets to realistic patient phantoms for CT dose and image quality testing. METHODS: CT images of two patients were radiopaque printed with aqueous potassium iodide solution (0.6 g/ml) on paper. Two methods were developed for assembling the paper sheets to head and neck phantoms. (1) Printed sheets were fed to a paper-based 3D printer along with corresponding 3D printable STL files. (2) Paper stacks of 5-mm thickness were glued with toner, cut to the patient shape and assembled to a phantom. In a sample application study, both phantoms were examined with five different tube current settings. Images were reconstructed using filtered-back projection (FBP) and iterative reconstruction (AIDR 3D) with three strength levels. Dose length product (DLP), signal-to-noise ratios (SNR) and contrast-to-noise ratios (CNRs) were analysed. Data were analysed using 2-way analysis of variance (ANOVA). RESULTS: Both methods achieved anthropomorphic phantoms with detailed patient anatomy. The 3D printer yielded a precise reproduction of the external patient shape, but caused visible glue artefacts. Gluing with toner avoided these artefacts and yielded more flexibility with regard to phantom size. In the sample application study, non-inferior SNR and CNR and up to 83.7% lower DLP were achieved on the phantoms with AIDR 3D compared with FBP. CONCLUSIONS: Two methods for assembling radiopaque printed paper sheets to phantoms of individual patients are presented. The sample application demonstrates potential for simulation of patient imaging and systematic CT dose and image quality assessment. KEY POINTS: • Two methods were developed to create realistic CT phantoms of individual patients from radiopaque printed paper sheets. • Analysis of five tube current and four reconstruction settings on two radiopaque 3D printed patient phantoms yielded non-inferior SNR and CNR and up to 83.7% lower dose with iterative reconstruction in comparison with filtered back projection. • Radiopaque 3D printed phantoms can simulate patients and allow systematic analysis of CT dose and image quality parameters.

A radiopaque 3D printed, anthropomorphic phantom for simulation of CT-guided procedures.

OBJECTIVES: To develop an anthropomorphic phantom closely mimicking patient anatomy and to evaluate the phantom for the simulation of computed tomography (CT)-guided procedures. METHODS: Patient CT images were printed with aqueous potassium iodide solution (1 g/mL) on paper. The printed paper sheets were stacked in alternation with 1-mm thick polyethylene foam layers, cut to the patient shape and glued together to create an anthropomorphic abdomen phantom. Ten interventional radiologists performed periradicular infiltration on the phantom and rated the phantom procedure regarding different aspects of suitability for simulating CT-guided procedures. RESULTS: Radiopaque printing in combination with polyethylene foam layers achieved a phantom with detailed patient anatomy that allowed needle placement. CT-guided periradicular infiltration on the phantom was rated highly realistic for simulation of anatomy, needle navigation and overall course of the procedure. Haptics were rated as intermediately realistic. Participants strongly agreed that the phantom was suitable for training and learning purposes. CONCLUSIONS: A radiopaque 3D printed, anthropomorphic phantom provides a realistic platform for the simulation of CT-guided procedures. Future work will focus on application for training and procedure optimisation. KEY POINTS: • Radiopaque 3D printing combined with polyethylene foam achieves patient phantoms for CT-guided procedures. • Radiopaque 3D printed, anthropomorphic phantoms allow realistic simulation of CT-guided procedures. • Realistic visual guidance is a key aspect in simulation of CT-guided procedures. • Three-dimensional printed phantoms provide a platform for training and optimisation of CT-guided procedures.