ABSTRACT
This article presents the findings of a study focusing on the gas generation of 3D-printed cores fabricated using binder-jetting technology with furfuryl resin. The research aimed to compare gas emission levels, where the volume generated during the thermal degradation of the binder significantly impacts the propensity for gaseous defects in foundries. The study also investigated the influence of the binder type (conventional vs. 3D-printed dedicated binder) and core construction (shell core) on the quantity of gaseous products from the BTEX group formed during the pouring of liquid foundry metal into the cores. The results revealed that the emitted gas volume during the thermal decomposition of the organic binder depended on the core sand components and binder type. Cores produced using conventional methods emitted the least gases due to lower binder content. Increasing Kaltharz U404 resin to 1.5 parts by weight resulted in a 37% rise in gas volume and 27% higher benzene emission. Adopting shell cores reduced gas volume by over 20% (retaining sand with hardener) and 30% (removing sand with hardener), presenting an eco-friendly solution with reduced benzene emissions and core production costs. Shell cores facilitated the quicker removal of gaseous binder decomposition products, reducing the likelihood of casting defects. The disparity in benzene emissions between 3D-printed and vibratory-mixed solid cores is attributed to the sample preparation process, wherein 3D printing ensured greater uniformity.
ABSTRACT
A new type of organobentonite foundry binder composed of a composite of bentonite (SN) and poly(acrylic acid) (PAA) was analyzed using thermal analysis (TG-DTG-DSC) and pyrolysis gas chromatography mass spectrometry (Py-GC/MS). The temperature range in which the composite retains its binding properties was identified using thermal analysis of the composite and its components. Results showed that the thermal decomposition process is complex and involves physicochemical transformations that are mainly reversible at temperatures in the ranges of 20-100 °C (related to evaporation of solvent water) and 100-230 °C (related to intermolecular dehydration). The decomposition of PAA chains occurs between 230 and 300 °C, while complete decomposition of PAA and formation of organic decomposition products takes place at 300-500 °C. Dehydroxylation of montmorillonite (MMT) in bentonite begins at about 500 °C, which leads to a drastic structural transformation. An endothermic effect associated with the remodeling of the mineral structure was observed on the DSC curve in the range of 500-750 °C. The produced SN/PAA composite was found to be thermostable during degradation in both oxidative and inert atmosphere, similar to the starting bentonite, and even maintained over a relatively higher and wider temperature range compared to organic binding materials used. At the given temperatures of 300 °C and 800 °C, only CO2 emissions occur from all the examined SN/PAA samples. There is no emission of compounds from the BTEX group. This means that the proposed binding material in the form of the MMT-PAA composite will not pose a threat to the environment and the workplace.
ABSTRACT
Casting cores produced in additive manufacturing are more often used in industrial practice, in particular in the case of the production of unit castings and castings with very complex geometry. The growing interest in the technology of 3D printing of cores and molds also brings emerging doubts related to their mechanical and technological properties. This article presents a comparison of the properties of cores made of sand with acid-curing furfuryl resin, made with 3D printing technology; the cores were prepared in a conventional way (mixing and compaction). The main purpose of this research was to determine the possibility of using shell cores as a substitute for solid cores, aimed at reducing the amount of binder in the core. The influence of the type of the binder and the size of the grain matrix fraction on the obtained mechanical and technological properties of the cores, with particular emphasis on abrasion and thermal deformation, as well as on the kinetics of their hardening, was demonstrated.
ABSTRACT
A series of studies related to the production of organobentonite, i.e., bentonite-poly(acrylic acid), and its use as a matrix grain-binding material in casting moulding sand is presented. In addition, a new carbon additive in the form of shungite was introduced into the composition of the moulding sand. Selected technological and strength properties of green sand bond with the obtained organobentonite with the addition of shungite as a new lustrous carbon carrier (Rcw, Rmw, Pw, Pw, PD) were determined. The introduction of shungite as a replacement for coal dust in the hydrocarbon resin system demonstrated the achievement of an optimum moulding sand composition for practical use in casting technology. Using chromatographic techniques (Py-GC/MS, GC), the positive effect of shungite on the quantity and quality of the gaseous products generated from the moulding sand during the thermal destruction of its components was noted, thus confirming the reduced environmental footprint of the new carbon additive compared to the commonly used lustrous carbon carriers. The test casting obtained in the mould of the organobentonite moulding sand and the shungite/hydrocarbon resin mixture showed a significantly better accuracy of the stepped model shape reproduction and surface smoothness compared to the casting obtained with the model moulding sand.
