ABSTRACT
The paper describes the development and the experimental validation of a cryogenic magnetic shielding system for transition edge sensor based space detector arrays. The system consists of an outer mu-metal shield and an inner superconducting niobium shield. First, a basic comparison is made between thin-walled mu-metal and superconducting shields, giving an off-axis expression for the field inside a cup-shaped superconductor as a function of the transverse external field. Starting from these preliminary analytical considerations, the design of an adequate and realistic shielding configuration for future space flight applications (either X-IFU [D. Barret et al., e-print arXiv:1308.6784 [astro-ph.IM] (2013)] or SAFARI [B. Jackson et al., IEEE Trans. Terahertz Sci. Technol. 2, 12 (2012)]) is described in more detail. The numerical design and verification tools (static and dynamic finite element method (FEM) models) are discussed together with their required input, i.e., the magnetic-field dependent permeability data. Next, the actual manufacturing of the shields is described, including a method to create a superconducting joint between the two superconducting shield elements that avoid flux penetration through the seam. The final part of the paper presents the experimental verification of the model predictions and the validation of the shield's performance. The shields were cooled through the superconducting transition temperature of niobium in zero applied magnetic field (<10 nT) or in a DC field with magnitude â¼100 µT, applied either along the system's symmetry axis or perpendicular to it. After cool-down, DC trapped flux profiles were measured along the shield axis with a flux-gate magnetometer and the attenuation of externally applied AC fields (100 µT, 0.1 Hz, both axial and transverse) was verified along this axis with superconducting quantum interference device magnetometers. The system's measured on-axis shielding factor is greater than 106, well exceeding the requirement of the envisaged missions. Following field-cooling in an axial field of 85 µT, the residual internal DC field normal to the detector plane is less than 1 µT. The trapped field patterns are compared to the predictions of the dynamic FEM model, which describes them well in the region where the internal field exceeds 6 µT.
ABSTRACT
The sensitivity of antenna systems increases with increasing active area, but decreases at higher noise figure of the low-noise amplifier (LNA). Cooling the LNA locally results in significant improvement in the gain and in lowering the noise figure of the LNA. Micromachined Joule-Thomson (JT) coolers can provide a cryogenic environment to the LNA. They are attractive because they have no cold moving parts and can be scaled down to match the size and the power consumption of LNAs. The performance of a LNA mounted on a JT microcooler with dimensions of 60.0 × 9.5 × 0.72 mm(3) is reported in this paper. The microcooler is operated with nitrogen gas and the cold-end temperature is controlled at 115 K. The measured net cooling power of the microcooler is about 43 mW when the LNA is not operating. The power dissipation of the LNA is 26 mW, with a supply voltage of 2 V. At room temperature the noise figure of the LNA is 0.83 dB and the gain lies between 17.9 and 13.1 dB, in the frequency range of 0.65 and 1.05 GHz. Upon cooling to 115 K, the noise figure drops to 0.50 dB and the increase in gain varies in the range of 0.6-1.5 dB.
ABSTRACT
The utilization of single-stage micromachined Joule-Thomson (JT) coolers for cooling small optical detectors is investigated. A design of a micromachined JT cold stage-detector system is made that focuses on the interface between a JT cold stage and detector, and on the wiring of the detector. Among various techniques, adhesive bonding is selected as most suitable technique for integrating the detector with the JT cold stage. Also, the optimum wiring of the detector is discussed. In this respect, it is important to minimize the heat conduction through the wiring. Therefore, each wire should be optimized in terms of acceptable impedance and thermal heat load. It is shown that, given a certain impedance, the conductive heat load of electrically bad conducting materials is about twice as high as that of electrically good conducting materials. A micromachined JT cold stage is designed and integrated with a dummy detector. The JT cold stage is operated at 100 K with nitrogen as the working fluid and at 140 K with methane. Net cooling powers of 143 mW and 117 mW are measured, respectively. Taking into account a radiative heat load of 40 mW, these measured values make the JT cold stage suitable for cooling a photon detector with a power dissipation up to 50 mW, allowing for another 27 to 53 mW heat load arising from the electrical leads.
ABSTRACT
Microminiature pulse tube cryocoolers should operate at a frequency of an order higher than the conventional macro ones because the pulse tube cryocooler operating frequency scales inversely with the square of the pulse tube diameter. In this paper, the design and experiments of a high frequency pressure oscillator is presented with the aim to power a micropulse tube cryocooler operating between 300 and 80 K, delivering a cooling power of 10 mW. Piezoelectric actuators operate efficiently at high frequencies and have high power density making them good candidates as drivers for high frequency pressure oscillator. The pressure oscillator described in this work consists of a membrane driven by a piezoelectric actuator. A pressure ratio of about 1.11 was achieved with a filling pressure of 2.5 MPa and compression volume of about 22.6 mm(3) when operating the actuator with a peak-to-peak sinusoidal voltage of 100 V at a frequency of 1 kHz. The electrical power input was 2.73 W. The high pressure ratio and low electrical input power at high frequencies would herald development of microminiature cryocoolers.
ABSTRACT
A breadboard 4.5 K helium sorption cooler for use in vibration-sensitive space missions was developed and successfully tested. This type of cooler has no moving parts and is, therefore, essentially vibration-free. The absence of moving parts also simplifies scaling down of the cooler to small sizes, and it contributes to achieving a very long lifetime. In addition, the cooler operates with limited dc's so that hardly any electromagnetic interference is generated. This cooler is a favorite option for future missions such as ESA's Darwin mission, a space interferometer in which the sensitive optics and detectors can hardly accept any vibration. The system design consists of a hydrogen stage cooling from 80 to 14.5 K and a helium stage establishing 5 mW at 4.5 K. Both stages use microporous activated carbon as the adsorption material. The two cooler stages need about 3.5 W of total input power and are heat sunk at two passive radiators at temperatures of about 50 and 80 K-radiators which are constructed at the cold side of the spacecraft. We developed, built, and tested a demonstrator of the helium cooler. This demonstrator has four sorption compressor cells in two compressor stages. Test experiments on this cooler showed that it performs within all specifications imposed by ESA. The cooler delivered 4.5 mW at 4.5 K with a long-term temperature stability of 1 mK and an input power of 1.96 W. So far, the cooler has operated continuously for a period of 2.5 months and has not shown any sign of performance degradation.
