Ultrafast, Selective, and Highly Sensitive Nonchromatographic Analysis of Fourteen Cannabinoids in Cannabis Extracts, Δ8-Tetrahydrocannabinol Synthetic Mixtures, and Edibles by Cyclic Ion Mobility Spectrometry-Mass Spectrometry.

The diversity of cannabinoid isomers and complexity of Cannabis products pose significant challenges for analytical methodologies. In this study, we developed a method to analyze 14 different cannabinoid isomers in diverse samples within milliseconds by leveraging the unique adduct-forming behavior of silver ions in advanced cyclic ion mobility spectrometry-mass spectrometry. The developed method achieved the separation of isomers from four groups of cannabinoids: Δ3-tetrahydrocannabinol (THC) (1), Δ8-THC (2), Δ9-THC (3), cannabidiol (CBD) (4), Δ8-iso-THC (5), and Δ(4)8-iso-THC (6) (all MW = 314); 9α-hydroxyhexahydrocannabinol (7), 9ß-hydroxyhexahydrocannabinol (8), and 8-hydroxy-iso-THC (9) (all MW = 332); tetrahydrocannabinolic acid (THCA) (10) and cannabidiolic acid (CBDA) (11) (both MW = 358); Δ8-tetrahydrocannabivarin (THCV) (12), Δ8-iso-THCV (13), and Δ9-THCV (14) (all MW = 286). Moreover, experimental and theoretical traveling wave collision cross section values in nitrogen (TWCCSN2) of cannabinoid-Ag(I) species were obtained for the first time with an average error between experimental and theoretical values of 2.6%. Furthermore, a workflow for the identification of cannabinoid isomers in Cannabis and Cannabis-derived samples was established based on three identification steps (m/z and isotope pattern of Ag(I) adducts, TWCCSN2, and MS/MS fragments). Afterward, calibration curves of three major cannabinoids were established with a linear range of 1-250 ng·ml-1 for Δ8-THC (2) (R2 = 0.9999), 0.1-25 ng·ml-1 for Δ9-THC (3) (R2 = 0.9987), and 0.04-10 ng·ml-1 for CBD (4) (R2 = 0.9986) as well as very low limits of detection (0.008-0.2 ng·ml-1). Finally, relative quantification of Δ8-THC (2), Δ9-THC (3), and CBD (4) in eight complex acid-treated CBD mixtures was achieved without chromatographic separation. The results showed good correspondence (R2 = 0.999) with those obtained by gas chromatography-flame ionization detection/mass spectrometry.

Comprehensive cannabinoid profiling of acid-treated CBD samples and Δ8-THC-infused edibles.

Δ8-Tetrahydrocannabinol (Δ8-THC) is increasingly popular as a controversial substitute for Δ9-tetrahydrocannabinol (Δ9-THC) in cannabinoid-infused edibles. Δ8-THC is prepared from cannabidiol (CBD) by treatment with acids. Side products including Δ9-THC and other isomers that might end up in Δ8-THC edibles are less studied. In this paper, three orthogonal methods, namely reversed-phase (RP)-UHPLC-DAD/HRMS, normal-phase/argentation (silica-Ag(I))-HPLC-DAD/MS, and GC-FID/MS were developed for analysis of cannabinoid isomers, namely Δ8-THC, Δ9-THC, CBD, Δ8-iso-THC, Δ(4)8-iso-THC, and hydrated THC isomers. Eight acid-treated CBD mixtures contained various amounts of Δ8-THC (0-89%, w/w%), high levels of Δ9-THC (up to 49%), Δ8-isoTHC (up to 55%), Δ(4)8-iso-THC (up to 17%), and three hydrated THC isomers. Commercial Δ8-THC gummies were also analyzed, and issues like overclaimed Δ8-THC, excessive Δ9-THC, undeclared Δ8-iso-THC, and Δ(4)8-iso-THC were found. These findings highlight the urgency of improving regulations towards converting CBD to Δ8-THC for use as food ingredients.

Bifunctional Ti4+-modified paper for selective extraction or removal of phospholipids and paper spray mass spectrometry for bioanalysis in urine and plasma.

BACKGROUND: Phospholipids (PLs) are major constituents of cell membranes, play important roles in cell proliferation and death, as well as in signal transduction, and therefore are relevant biomarkers for different pathologies. On the other hand, when the analysis of small compounds, such as therapeutics in blood is desired, then phospholipids are part of the matrix and cause serious interference during analysis. Currently, both the analysis and removal of PLs from biological samples are limited by extensive sample preparation and instrumental separation. RESULTS: A fast and simple quantitative Ti4+-modified paper spray tandem mass spectrometric (TiPS-MS/MS) method was established in urine, where the enrichment of phospholipids was achieved, as well as reduction of matrix effects (primarily caused by high salt content) that ultimately led to improved sensitivity and selectivity. The method could achieve a physiologically relevant limit of detection (0.01-0.03 µg mL-1). Also, the usefulness of the Ti4+-modified paper was investigated in the opposite mode, namely for the selective removal of phospholipids from matrices such as plasma. Clonidine is used as model compound, as the detection of this compound is known to suffer from ion suppression by phospholipids. Compared with blank paper spray tandem mass spectrometry, the limit of detection could be improved from 0.3 µg mL-1 to 0.03 µg mL-1 by employing a Ti4+-modified paper on top of the spray tip to capture phospholipids from the sample. SIGNIFICANCE AND NOVELTY: A novel Ti4+-modified paper was developed to allow for rapid solid-phase extraction of phospholipids from urine or selective removal from plasma, followed by direct paper spray mass spectrometric detection as a fast and convenient sample preparation and analysis combination. The paper properties are based on the Ti4+ metal ion, which can selectively bind phosphate-containing compounds under acidic conditions, and its applicability was demonstrated in relevant biological matrices.

Boronate affinity paper spray mass spectrometry for determination of elevated levels of catecholamines in urine.

The analysis of catecholamines, such as dopamine, epinephrine and norepinephrine in urine can be used in the diagnosis of certain pathologies, such as hormone-producing tumors. Here, a fast and simple quantitative boronate affinity paper spray tandem mass spectrometric (PS-MS/MS) method is established, which can improve selectivity and reduce ion suppression without needing any instrumental chromatography. We use here the property of boronic acids, which can selectively bind ortho-diol-containing compounds under alkaline conditions. Paper tip modification and catechol enrichment protocols were developed to selectively bind, clean up and subsequently desorb such catecholamines. Standard catecholamine solutions, as well as human urine samples were analyzed with the PS-MS(/MS) method, which is fast, cheap and easy-to-operate compared to HPLC-MS/MS. Despite its high simplicity, boronate affinity PS-MS/MS exhibits good performance compared to HPLC-MS/MS in human urine analysis in terms of precision (2.1%-7.2% vs. 1.1%-2.9%) and accuracy (-10.2%-9.3% vs. -4.8%-5.1%), and a physiologically relevant limit of detection (0.027-0.12 µg mL-1). The boronate affinity PS-MS/MS clearly achieved the detection limits that would allow the fast analysis of urine samples for clinical purposes, such as screening for pheochromocytoma (exceeding 0.5 µg mL-1).

Semiquantitative Screening of THC Analogues by Silica Gel TLC with an Ag(I) Retention Zone and Chromogenic Smartphone Detection.

With the ever-evolving cannabis industry, low-cost and high-throughput analytical methods for cannabinoids are urgently needed. Normally, (potentially) psychoactive cannabinoids, typically represented by Δ9-tetrahydrocannabinol (Δ9-THC), and nonpsychoactive cannabinoids with therapeutic benefits, typically represented by cannabidiol (CBD), are the target analytes. Structurally, the former (tetrahydrocannabinolic acid (THCA), cannabinol (CBN), and THC) have one olefinic double bond and the latter (cannabidiolic acid (CBDA), cannabigerol (CBG), and CBD) have two, which results in different affinities toward Ag(I) ions. Thus, a silica gel thin-layer chromatography (TLC) plate with the lower third impregnated with Ag(I) ions enabled within minutes a digital chromatographic separation of strongly retained CBD analogues and poorly retained THC analogues. The resolution (Rs) between the closest two spots from the two groups was 4.7, which is almost 8 times higher than the resolution on unmodified TLC. After applying Fast Blue BB as a chromogenic reagent, smartphone-based color analysis enabled semiquantification of the total percentage of THC analogues (with a limit of detection (LOD) of 11 ng for THC, 54 ng for CBN, and 50 ng for THCA when the loaded volume is 1.0 µL). The method was validated by analyzing mixed cannabis extracts and cannabis extracts. The results correlated with those of high-performance liquid chromatography with ultraviolet detection (HPLC-UV) (R2 = 0.97), but the TLC approach had the advantages of multi-minute analysis time, high throughput, low solvent consumption, portability, and ease of interpretation. In a desiccator, Ag(I)-TLC plates can be stored for at least 3 months. Therefore, this method would allow rapid distinction between high and low THC varieties of cannabis, with the potential for on-site applicability.

Chromatographic Determination of the Mycotoxin Patulin in 219 Chinese Tea Samples and Implications for Human Health.

Patulin (PAT) is a mycotoxin, with several acute, chronic, and cellular level toxic effects, produced by various fungi. A limit for PAT in food of has been set by authorities to guarantee food safety. Research on PAT in tea has been very limited although tea is the second largest beverage in the world. In this paper, HPLC-DAD and GC-MS methods for analysis of PAT in different tea products, such as non-fermented (green tea), partially fermented (oolong tea, white tea, yellow tea), completely fermented (black tea), and post-fermented (dark tea and Pu-erh tea) teas were developed. The methods showed good selectivity with regard to tea pigments and 5-hydroxymethylfurfural (5-HMF) and a recovery of 90-102% for PAT at a 10-100 ppb spiking level. Limit of detection (LOD) and limit of quantification (LOQ) in tea were 1.5 ng/g and 5.0 ng/g for HPLC-UV, and 0.25 ng/g and 0.83 ng/g for GC-MS. HPLC was simpler and more robust, while GC-MS showed higher sensitivity and selectivity. GC-MS was used to validate the HPLC-UV method and prove its accuracy. The PAT content of 219 Chinese tea samples was investigated. Most tea samples contained less than 10 ng/g, ten more than 10 ng/g and two more than 50 ng/g. The results imply that tea products in China are safe with regard to their PAT content. Even an extreme daily consumption of 25 g of the tea with the highest PAT content (124 ng/g), translates to an intake of only 3 µg/person/day, which is still an order of magnitude below the maximum allowed daily intake of 30 µg for an adult.

Microextraction of Reseda luteola-Dyed Wool and Qualitative Analysis of Its Flavones by UHPLC-UV, NMR and MS.

Detailed knowledge on natural dyes is important for agronomy and quality control as well as the fastness, stability, and analysis of dyed textiles. Weld (Reseda luteola L.), which is a source of flavone-based yellow dye, is the focus of this study. One aim was to reduce the required amount of dyed textile to ≤50 µg for a successful chromatographic analysis. The second aim was to unambiguously confirm the identity of all weld flavones. By carrying out the extraction of 50 µg dyed wool with 25 µL of solvent and analysis by reversed-phase UHPLC at 345 nm, reproducible chromatographic fingerprints could be obtained with good signal to noise ratios. Ten baseline separated peaks with relative areas ≥1% were separated in 6 min. Through repeated polyamide column chromatography and prepHPLC, the compounds corresponding with the fingerprint peaks were purified from dried weld. Each was unequivocally identified, including the position and configuration of attached sugars, by means of 1D and 2D NMR and high-resolution MS. Apigenin-4'-O-glucoside and luteolin-4'-O-glucoside were additionally identified as two trace flavones co-eluting with other flavone glucosides, the former for the first time in weld. The microextraction might be extended to other used dye plants, thus reducing the required amount of precious historical textiles.

Rapid Distinction and Semiquantitative Analysis of THC and CBD by Silver-Impregnated Paper Spray Mass Spectrometry.

The control over the amount of psychoactive THC (Δ-9-tetrahydrocannabinol) in commercial cannabidiol (CBD) products has to be strict. A fast and simple semiquantitative Ag(I)-impregnated paper spray mass spectrometric method for differentiating between THC and CBD, which show no difference in standard single-stage or tandem MS, was established. Because of a different binding affinity to Ag(I) ions, quasi-molecular Ag(I) adducts [THC + Ag]+ and [CBD + Ag]+ at m/z 421 and 423 give different fragmentation patterns. The product ions at m/z 313 for THC and m/z 353 and 355 for CBD can be used to distinguish THC and CBD and to determine their ratio. Quantification of THC/CBD ratios in commercial CBD oils was accomplished with a low matrix effect (-2.2 ± 0.4% for THC and -2.0 ± 0.3% for CBD). After simple methanol extraction (recovery of 87.3 ± 1.2% for THC and 92.3 ± 1.4% for CBD), Ag(I)-impregnated paper spray analysis was employed to determine this ratio. A single run can be completed in a few minutes. This method was benchmarked against the UHPLC-UV method. Ag(I)-impregnated paper spray MS had the same working range (THC/CBD = 0.001-1) as UHPLC-UV analysis (R2 = 0.9896 and R2 = 0.9998, respectively), as well as comparable accuracy (-2.7 to 14%) and precision (RSD 1.7-11%). The method was further validated by the analysis of 10 commercial oils by Ag(I)-impregnated paper spray MS and UHPLC-UV analysis. Based on the determined relative concentration ratios of THC/CBD and the declared CBD concentration, 6 out of 10 CBD oils appear to contain more THC than the Dutch legal limit of 0.05%.

Microfluidic Chip-Based Induced Phase Separation Extraction as a Fast and Efficient Miniaturized Sample Preparation Method.

Induced phase separation extraction (IPSE) is an efficient sample clean-up technique that can replace liquid-liquid extraction (LLE). The purpose of this study was to miniaturize IPSE by carrying it out in a microfluidic chip. An IPSE chip was designed and evaluated for its ability to separate and purify samples on a microscale. The 5 × 2 cm chip was fed with a solution of polar to non-polar model compounds in acetonitrile-water (1:1). In the 100 µm wide and 40 µm deep microchannels, the sample solution was efficiently separated into two immiscible phases by adding a hydrophobic solvent as inducer. Analytes present in the sample solution each migrated to their own favorable phase upon phase separation. After optimization, extraction and fractionation were easily and efficiently achieved. The behavior of analytes with a pH-dependent partitioning could be influenced by adjusting the pH of the sample solution. Scutellaria baicalensis extract, used in Traditional Chinese Medicine (TCM), was successfully separated in aglycones and glycosides. In this microscale system, the sample and solvent consumption is reduced to microliters, while the time needed for the sample pretreatment is less than one minute. Additionally, the extraction efficiency can reach up to 98.8%, and emulsion formation is avoided.

A micro-solid phase extraction device to prepare a molecularly imprinted porous monolith in a facile mode for fast protein separation.

A molecularly imprinted polymeric monolith was synthesized in an aqueous environment in 15 min via UV-irradiation. The imprinted monolith was composed of hydroxyethyl methacrylate as monomer, dimethyl amino ethyl methacrylate as functional monomer, methylene bisacrylamide and piperazine diacrylamide as crosslinkers and human serum albumin as template molecule. The synthesis took place in a PDMS-based device (2.5 cm long) yielding a micro-solid phase extraction column (3 × 5 mm) with two built-in fingertight connectors for an infusion pump and fraction collector. The imprinted monolith displayed the characteristic features of a porous polymeric monolith, had dimethyl amino ethyl methacrylate and human serum albumin as functional groups within the monolith and showed high permeability (0.51 × 10-13 m2). 85% of the imprinted cavities were readily available for rebinding of human serum albumin with an imprinting factor of 1.3. In comparison to a non-imprinted monolith, molecular imprinting increased human serum albumin adsorption by > 30%. Imprinted monolith displayed selectivity for human serum albumin over other competing proteins (human transferrin, ovalbumin and carbonic anhydrase) with similar or different isoelectric points and size. Human serum albumin was adsorbed (in dynamic mode) with > 98% selectivity from diluted human plasma using the imprinted monolith device. Device to device reproducibility and reusability of the device for 5 cycles showcase the imprinted monolith micro-device efficiency.

Rapid Analysis of Illegal Cationic Dyes in Foods and Surface Waters Using High Temperature Direct Analysis in Real Time High-Resolution Mass Spectrometry.

A high temperature desorption (HTD) direct analysis in real time-high-resolution mass spectrometric (DART-HRMS) method was developed for the rapid analysis of four banned cationic dyes. Rhodamine B is used to dye foods, while malachite green, crystal violet, and methylene blue are added to fishponds as antimicrobials. A simple induced phase separation extraction was used to pretreat samples. The DART-HRMS method employed two temperature steps, i.e., 200 °C for drying, purification, and enrichment of sample solution and 500 °C for thermal desorption and ionization of analytes. The calibration curves of dyes in the range of 50-2000 ng/mL were linear using deuterated malachite green as an internal standard. The LODs vary for all analytes between 0.1 and 30 ppb depending on the matrix and experimental conditions. Through analyses of real samples, two chili powders and one chili oil were found to be contaminated by rhodamine B. The concentrations were comparable with those found by an HPLC-MS/MS method.

Is Low-field NMR a Complementary Tool to GC-MS in Quality Control of Essential Oils? A Case Study: Patchouli Essential Oil.

High-field NMR is an expensive and important quality control technique. In recent years, cheaper and simpler low-field NMR has become available as a new quality control technique. In this study, 60 MHz 1H-NMR was compared with GC-MS and refractometry for the detection of adulteration of essential oils, taking patchouli essential oil as a test case. Patchouli essential oil is frequently adulterated, even today. In total, 75 genuine patchouli essential oils, 10 commercial patchouli essential oils, 10 other essential oils, 17 adulterants, and 1 patchouli essential oil, spiked at 20% with those adulterants, were measured. Visual inspection of the NMR spectra allowed for easy detection of 14 adulterants, while gurjun and copaiba balsams proved difficult and one adulterant could not be detected. NMR spectra of 10 random essential oils differed not only strongly from patchouli essential oil but also from one another, suggesting that fingerprinting by low-field NMR is not limited to patchouli essential oil. Automated chemometric evaluation of NMR spectra was possible by similarity analysis (Mahalanobis distance) based on the integration from 0.1 - 8.1 ppm in 0.01 ppm increments. Good quality patchouli essential oils were recognised as well as 15 of 17 deliberate adulterations. Visual qualitative inspection by GC-MS allowed for the detection of all volatile adulterants. Nonvolatile adulterants, and all but one volatile adulterant, could be detected by semiquantitation. Different chemometric approaches showed satisfactory results. Similarity analyses were difficult with nonvolatile adulterants. Refractive index measurements could detect only 8 of 17 adulterants. Due to advantages such as simplicity, rapidity, reproducibility, and ability to detect nonvolatile adulterants, 60 MHz 1H-NMR is complimentary to GC-MS for quality control of essential oils.

Biochip Spray: Simplified Coupling of Surface Plasmon Resonance Biosensing and Mass Spectrometry.

A simplified coupling of surface plasmon resonance (SPR) immuno-biosensing with ambient ionization mass spectrometry (MS) was developed. It combines two orthogonal analysis techniques: the biosensing capability of SPR and the chemical identification power of high resolution MS. As a proof-of-principle, deoxynivalenol (DON), an important mycotoxin, was captured using an SPR gold chip containing an antifouling layer and monoclonal antibodies against the toxin and, after washing, the chip could be taken out and analyzed by direct spray MS of the biosensor chip to confirm the identity of DON. Furthermore, cross-reacting conjugates of DON present in a naturally contaminated beer could be successfully identified, thus showing the potential of rapid identification of (un)expected cross-reacting molecules.

Analysis of Mycotoxins in Beer Using a Portable Nanostructured Imaging Surface Plasmon Resonance Biosensor.

A competitive inhibition immunoassay is described for the mycotoxins deoxynivalenol (DON) and ochratoxin A (OTA) in beer using a portable nanostructured imaging surface plasmon resonance (iSPR) biosensor, also referred to as imaging nanoplasmonics. The toxins were directly and covalently immobilized on a 3-dimensional carboxymethylated dextran (CMD) layer on a nanostructured iSPR chip. The assay is based on competition between the immobilized mycotoxins and free mycotoxins in the solution for binding to specific antibodies. The chip surface was regenerated after each cycle, and the combination of CMD and direct immobilization of toxins allowed the chips to be used for more than 450 cycles. The limits of detection (LODs) in beer were 17 ng/mL for DON and 7 ng/mL for OTA (or 0.09 ng/mL after 75 times enrichment). These LODs allowed detection of even less than 10% depletion of the tolerable daily intake of DON and OTA by beer. Significant cross-reactivity of anti-DON was observed toward DON-3-glucoside and 3-acetyl-DON, while no cross-reactivity was seen for 15-acetyl-DON. A preliminary in-house validation with 20 different batches of beer showed that both toxins can be detected at the considered theoretical safe level for beer. The assay can be used for in-field or at-line detection of DON in beer and also in barley without preconcentration, while OTA in beer requires an additional enrichment step, thus making the latter in its present form less suitable for field applications.

Chemometric analysis of comprehensive LC×LC-MS data: Resolution of triacylglycerol structural isomers in corn oil.

Comprehensive hyphenated two-dimensional liquid chromatography mass spectrometry (LC×LC-MS) is a very powerful analytical tool achieving high throughput resolution of highly complex natural samples. However, even using this approach there is still the possibility of not resolving some of the analytes of interest. For instance, triacylglycerols (TAGs) structural isomers in oil samples are extremely difficult to separate chromatographically due to their very similar structure and chemical properties. Traditional approaches based on current vendor chromatographic software cannot distinguish these isomers from their different mass spectral features. In this work, a chemometric approach is proposed to solve this problem. First, the experimental LC×LC-MS data structure is discussed, and results achieved by different methods based on the fulfilment of the trilinear model are compared. Then, the step-by-step resolution and identification of strongly coeluted compounds from different examples of triacylglycerols (TAGs) structural isomers in corn oil samples are described. As a conclusion, the separation power of two-dimensional chromatography can be significantly improved when it is combined with the multivariate curve resolution method.

Critical comparison of mass analyzers for forensic hair analysis by ambient ionization mass spectrometry.

RATIONALE: Recently, several direct and/or ambient mass spectrometry (MS) approaches have been suggested for drugs of abuse imaging in hair. The use of mass spectrometers with insufficient selectivity could result in false-positive measurements due to isobaric interferences. Different mass analyzers have been evaluated regarding their selectivity and sensitivity for the detection of Δ9-tetrahydrocannabinol (THC) from intact hair samples using direct analysis in real time (DART) ionization. METHODS: Four different mass analyzers, namely (1) an orbitrap, (2) a quadrupole orbitrap, (3) a triple quadrupole, and (4) a quadrupole time-of-flight (QTOF), were evaluated. Selectivity and sensitivity were assessed by analyzing secondary THC standard dilutions on stainless steel mesh screens and blank hair samples, and by the analysis of authentic cannabis user hair samples. Additionally, separation of isobaric ions by use of travelling wave ion mobility (TWIM) was investigated. RESULTS: The use of a triple quadrupole instrument resulted in the highest sensitivity; however, transitions used for multiple reaction monitoring were only found to be specific when using high mass resolution product ion measurements. A mass resolution of at least 30,000 FWHM at m/z 315 was necessary to avoid overlap of THC with isobaric ions originating from the hair matrix. Even though selectivity was enhanced by use of TWIM, the QTOF instrument in resolution mode could not indisputably differentiate THC from endogenous isobaric ions in drug user hair samples. CONCLUSIONS: Only the high resolution of the (quadrupole) orbitrap instruments and the QTOF instrument in high-resolution mode distinguished THC in hair samples from endogenous isobaric interferences. As expected, enhanced selectivity compromises sensitivity and THC was only detectable in hair from heavy users. Copyright © 2016 John Wiley & Sons, Ltd.

(Un)targeted Scanning of Locks of Hair for Drugs of Abuse by Direct Analysis in Real Time-High-Resolution Mass Spectrometry.

Forensic hair evidence can be used to obtain retrospective timelines of drug use by analysis of hair segments. However, this is a laborious and time-consuming process, and mass spectrometric (MS) imaging techniques, which show great potential for single-hair targeted analysis, are less useful due to differences in hair growth rate between individual hairs. As an alternative, a fast untargeted analysis method was developed that uses direct analysis in real time-high-resolution mass spectrometry (DART-HRMS) to longitudinally scan intact locks of hair without extensive sample preparation or segmentation. The hair scan method was validated for cocaine against an accredited liquid chromatography/tandem mass spectrometry (LC/MS/MS) method. The detection limit for cocaine in hair was found to comply with the cutoff value of 0.5 ng/mg recommended by the Society of Hair Testing; that is, the DART hair scan method is amenable to forensic cases. Under DART conditions, no significant thermal degradation of cocaine occurred. The standard DART spot size of 5.1 ± 1.1 mm could be improved to 3.3 ± 1.0 mm, corresponding to approximately 10 days of hair growth, by using a high spatial resolution exit cone. By use of data-dependent product ion scans, multiple drugs of abuse could be detected in a single drug user hair scan with confirmation of identity by both exact mass and MS/HRMS fragmentation patterns. Furthermore, full-scan high-resolution data were retrospectively interrogated versus a list of more than 100 compounds and revealed additional hits and temporal profiles in good correlation with reported drug use.

Evidence based decontamination protocols for the removal of external Δ9-tetrahydrocannabinol (THC) from contaminated hair.

External contamination can cause false positive results in forensic hair testing for drugs of abuse and is therefore a major concern when hair evidence is used in court. Current literature about decontamination strategies is mainly focused on external cocaine contamination and no consensus on the best decontamination procedure for hair samples containing cannabinoids has been reached so far. In this study, different protocols with solvents, both organic as well as aqueous, were tested on blank and drug user hair for their performance on removing external cannabis contamination originating from either smoke or indirect contact with cannabis plant material. Smoke contamination was mimicked by exposing hair samples to smoke from a cannabis cigarette and indirect contact contamination by handling hair with cannabis contaminated gloves or hands. Δ9-tetrahydrocannabinol (THC) levels in the hair samples and wash solvents were determined using liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis. Aqueous surfactant solutions removed more THC contamination compared to water, but much less than organic solvents. Methanol, dichloromethane and chloroform were most efficient in removing THC contamination. Due to its lower environmental impact, methanol was chosen as the preferred decontamination solvent. After testing of different sequential wash steps on externally contaminated blank hair, three protocols performed equally well, removing all normal level and more than 99% of unrealistically high levels of external cannabis contamination. Thorough testing on cannabis users' hair, both as such and after deliberate contamination, showed that using these protocols all contamination could be washed from the hair while no incorporated THC was removed from truly positive samples. The present study provides detailed scientific evidence in support of the recommendations of the Society of Hair Testing: a protocol using a single methanol wash followed by a single aqueous SDS solution wash, followed by a Milli-Q water rinsing step, is suggested as the preferred decontamination protocol to remove external cannabis contamination from hair while preserving the incorporated compounds.

Multiplex surface plasmon resonance biosensing and its transferability towards imaging nanoplasmonics for detection of mycotoxins in barley.

A 6-plex competitive inhibition immunoassay for mycotoxins in barley was developed on a prototype portable nanostructured imaging surface plasmon resonance (iSPR) instrument, also referred to as imaging nanoplasmonics. As a benchmark for the prototype nanoplasmonics instrument, first a double 3-plex assay was developed for the detection of deoxynivalenol (DON), zearalenone (ZEA), T-2 toxin (T-2), ochratoxin A (OTA), fumonisin B1 (FB1) and aflatoxin B1 (AFB1) using a well-established benchtop SPR instrument and two biosensor chips. To this end, ovalbumin (OVA) conjugates of mycotoxins were immobilized on the chip via amine coupling. The SPR response was then recorded upon injection of a mixture of antibodies at a fixed concentration and the sample (or matrix-matched standard) over a chip with immobilized mycotoxin-OVA conjugates. The chips were regenerated after each sample using 10 mM HCl and 20 mM NaOH and could be used for at least 60 cycles. The limits of detection in barley (in µg kg(-1)) were determined to be 26 for DON, 6 for ZEA, 0.6 for T-2, 3 for OTA, 2 for FB1 and 0.6 for AFB1. Preliminary in-house validation showed that DON, T-2, ZEA and FB1 can be detected at the European Union regulatory limits, while for OTA and AFB1 sensitivities should be improved. Furthermore, measurement of naturally contaminated barley showed that the assay can be used as a semi-quantitative screening method for mycotoxins prior to liquid chromatography tandem mass spectrometry (LC-MS/MS). Finally, using the same bio-reagents the assay was transferred to a 6-plex format in the nanoplasmonics instrument and subsequently the two assays were compared. Although less sensitive, the 6-plex portable iSPR assay still allowed detection of DON, T-2, ZEA and FB1 at relevant levels. Therefore, the prototype iSPR shows potential for future applications in rapid in-field and at-line screening of multiple mycotoxins.

Selective on-line detection of boronic acids and derivatives in high-performance liquid chromatography eluates by post-column reaction with alizarin.

An on-line high-performance liquid chromatography (HPLC) method for the rapid and selective detection of boronic acids in complex mixtures was developed. After optimization experiments at an HPLC flow rate of 0.40 mL/min, the HPLC-separated analytes were mixed post-column with a solution of 75 µM alizarin and 0.1% triethylamine in acetonitrile, which was delivered at a flow rate of 0.60 mL/min. The reaction between alizarin and boronic acids occurred in a reaction coil of dimensions of 3.5 m × 0.25 mm at a temperature of 50 °C, resulting in fluorescent complexes that were detected as positive peaks by a fluorescence detector (λexc 469 nm and λe m 610 nm). The method enabled the selective detection of various boronic acids and derivatives, with a limit of detection of phenylboronic acid of 1.2 ng or 1 µM. It could successfully monitor the progress of two organic reactions involving boronic acid-containing compounds, and provided useful insights into the course of the reactions.