Effect of radiotherapy, immediate dentin sealing and irrigation simulating single- or two-visits endodontic treatment on the bond strength to pulp chamber dentin: an in vitro study.

This study aimed to evaluate the influence of radiotherapy and different endodontic treatment protocols on the bond strength to pulp chamber dentin. Eighty mandibular molars were randomly divided into two groups (n = 40): non-irradiated and irradiated (60 Gy). The pulp chambers were sectioned, and each group was subdivided (n = 8), according to the endodontic treatment protocol: no treatment (Control); Single-visit; Two-visits; Immediate dentin sealing (IDS) + single-visit; and IDS + two-visits. Each endodontic treatment visit was simulated through irrigation with 2.5% NaOCl, 17% EDTA and distilled water. IDS was performed by actively applying two coats of a universal adhesive to the lateral walls of the pulp chamber. After, the pulp chambers were restored with resin composite and four sticks were obtained for microtensile test. In addition, the dentin of the pulp chamber roof was assessed for surface roughness, chemical composition, and topography after each treatment protocol. Two-way ANOVA, Tukey's post hoc, Mann-Whitney, Kruskal-Wallis and Dunn's post hoc were performed (α = 5%). The treatment protocol affected bond strength (p < 0.05), while the irradiation did not (p > 0.05). The control group presented the highest values (p < 0.05). The single-visit group demonstrated better performance compared to the other groups (p < 0.05), which did not differ from each other (p > 0.05) The use of IDS changed the surface roughness (p < 0.05), chemical composition (p < 0.05) and topography of the dentin. In conclusion, the treatment protocol influenced dentin adhesion, while irradiation did not.

Assessment of the Efficacy and Bond Strength of Different Dentin-bonding Agents with Adhesives on Primary Teeth: An In Vitro Study.

AIM: The purpose of this study was to evaluate the effectiveness and strength of three various dentin-bonding agents used with adhesives on primary teeth. MATERIALS AND METHODS: The study used 80 recently extracted, healthy human maxillary anterior primary teeth that had undergone physiologic resorption, or over-retention. Teeth were cut to expose a flat dentin surface at a depth of 1.5 mm. All samples were divided into four groups (20 samples in each group) as follows: Group I-Control group, Group II-Primary teeth bonding with 6th-generation bonding agent, Group III-Primary teeth bonding with 7th-generation bonding agent, Group IV-Primary teeth bonding with 8th-generation bonding agent. All of the samples' dentinal surfaces were covered with composite resin using a Teflon mold after adhesive had been applied. A universal testing machine (INSTRON) was used to assess the shear bond strength. Data were collected and statistically analyzed. RESULTS: The maximum mean shear bond strength was found in 8th-generation bonding agent (30.76 ± 0.16), followed by 7th-generation bonding agent (26.08 ± 0.21), 6th-generation bonding agent (25.32 ± 0.06), and control group (6.18 ± 0.09). Statistically significant difference was found between the three different bonding agents (p < 0.001). CONCLUSION: On conclusion, the 8th-generation bonding agent demonstrated a greater shear bond strength to dentin than the 7th and 6th-generation bonding agent. CLINICAL SIGNIFICANCE: The emergence of different bonding techniques to the market improves the durability and quality of restorations. An effective bonding to the tooth would also reduce bacterial penetration, marginal microleakage, possibility of pulpal inflammation preserve tooth structure, and postoperative sensitivity by allowing less cavity preparation. How to cite this article: Alqarni AS, Al Ghwainem A. Assessment of the Efficacy and Bond Strength of Different Dentin-bonding Agents with Adhesives on Primary Teeth: An In Vitro Study. J Contemp Dent Pract 2024;25(4):342-345.

Effects of different plasma treatments on bonding properties of zirconia.

This in vitro study was to evaluate the effect of different non-thermal atmospheric pressure plasma (NTP) on shear bond strength (SBS) between yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) and self-adhesive resin cement. In this study, The Y-TZP specimens were divided into 4 groups according to the surface treatment methods as follows: Control (no surface treatment), Sb (Sandblasting), AP(argon NTP), and CP(20 % oxygen and 80 % argon combination NTP). Y-TZP specimens were randomly selected from each group to observe and test the following indexes: scanning electron microscope to observe the surface morphology; atomic force microscope to detect the surface roughness; contact angle detector to detect the surface contact angle; energy spectrometer to analyze the surface elements. Then, resin cement (Rely X-U200) was bonded to human isolated teeth with Y-TZP specimens to measure SBS. The results showed that for the SE test, the NTP group was significantly higher than the control group (p < 0.05). The results of the SBS test showed that the SBS values of the NTP group were significantly higher than those of the other groups, regardless of the plasma treatment (p < 0.05). However, there was no significant difference between groups AP and CP in a test of SBS (p > 0.05). This study shows that non-thermal atmospheric pressure plasma can improve the shear bond strength of Y-TZP by increasing the surface energy. The addition of oxygen ratio to argon is more favorable to increase the shear bond strength and is worth further investigation.

Effect of Different Adhesive Resin and Composite Veneering Materials on Adhesion to Polyetheretherketone.

OBJECTIVE: To evaluate the effect of different adhesives and veneering resins on the shear bond strength (SBS) of polyetheretherketone (PEEK). METHODS: A total of 138 PEEK specimens were randomly divided into 6 groups according to adhesive material application: Control (C, no application), Adhese Universal (A) (Ivoclar Vivadent, Schaan, Liechtenstein), Gluma Bond Universal (G) (Heraeus Kulzer, South Bend, IN, USA), G-PremioBOND (P) (GC Corporation, Tokyo, Japan), Single Bond Universal (S) (3M, Saint Paul, MN, USA) and visio.link (V) (Bredent, Senden, Germany). Each adhesive group was divided into two subgroups according to the type of veneering material: Estenia direct composite (D) and Gradia Plus indirect composite (IN) (both GC Corporation). After the veneering process, the specimens were aged by thermal cycling. Kruskal-Wallis and Mann-Whitney U tests were used for SBS analysis (P < 0.05). RESULTS: The highest SBS results were obtained in the VIN group, followed by the VD, PD, GIN, AIN, AD, SIN, SD, PIN, GD, CIN and CD groups, respectively (P = 0.001). There were no significant differences in terms of the type of veneering composite when the same adhesive was applied (P > 0.05), except for Gluma Bond Universal (P = 0.009). All the adhesives tested showed clinically acceptable SBS results. CONCLUSION: Visio.link offered the highest adhesion to PEEK, whereas the tested universal adhesives may be used as an alternative to visio.link in clinical settings. It was determined that changing the veneer type has no statistical difference when the same adhesive material is used.

Evaluating the advancements in a recently introduced universal adhesive compared to its predecessor.

Background/purpose: The dental adhesive market is constantly evolving to meet the demands of dentists and patients, but new products and upgrades should be rigorously evaluated before being used in clinical practice. This study investigated the physicomechanical properties and dentin bonding efficacy of a newly upgraded universal adhesive compared to its predecessor. Materials and methods: Twenty-four molars were divided into four groups (n = 6/group) based on adhesive (new vs. predecessor) and application mode [self-etch (SE) vs. etch-and-rinse (ER)] for evaluating their dentin microtensile bond strength (µTBS), failure pattern, and bonding interface. Additional thirty-six molars' crowns were perpendicularly sectioned to obtain flat mid-coronal dentin discs. The opposing dentin surfaces of each disc received contrasting treatments (new/predecessor adhesive applied in SE/ER mode), resulting in six interventions. The bonded discs (n = 6/intervention) were used to assess the adhesives' survival probability employing a double-sided µTBS test. The other physicomechanical properties examined were adhesives' oxygen inhibition layer (OIL), viscosity, hardness, elastic modulus, degree of conversion (DC), and in-situ DC. Results: Both adhesive versions showed similar µTBS (P > 0.05), failure pattern (P > 0.05), and survival probability (P > 0.008). ER mode promoted resin tag formation and exhibited a slender adhesive layer for both adhesives. The newer adhesive version showed a thinner adhesive layer in general with narrower OIL (P < 0.001), less viscosity (P < 0.001), higher hardness (P < 0.05), elastic modulus (P < 0.05), DC (P < 0.001), and in-situ DC (P < 0.001). Conclusion: While the newly updated adhesive had superior physicomechanical properties with more fluidity, its dentin bonding efficacy and survival probability were comparable to its predecessor.

Comparative Evaluation of the Effect of Different Types of Bleaching Dentifrices on Shear Bond Strength of Orthodontic Metal Brackets Bonded by Conventional Composite to Human Teeth: An In Vitro Study.

AIM: This study aims to evaluate and compare the effect of different types of bleaching dentifrices on the shear bond strength of orthodontic metal brackets bonded by light-cured composite adhesive to human teeth. MATERIALS AND METHODS: Forty-five human premolar teeth were randomly divided into three groups, receiving the following treatments: Group 1 (control group; teeth in this group were not bleached), Group 2 (teeth in this group were treated with active oxygen bleaching dentifrice), and Group 3 (teeth in this group were treated with peroxide bleaching dentifrice). Orthodontic brackets were bonded using a light-cured composite adhesive. A universal measuring device was used to assess the shear bond strength with a crosshead speed of 0.5 mm/min. One-way ANOVA, post hoc Tukey tests, and an independent t-test were used to analyse the data. RESULTS: There was a highly significant difference (p≤0.001) in the mean shear bond strength of orthodontic brackets bonded to untreated teeth as compared to teeth treated with bleaching dentifrice. There was no significant difference in the mean shear bond strength of orthodontic brackets bonded to teeth treated with peroxide bleaching dentifrice or active oxygen bleaching dentifrice. CONCLUSION: There was a significant reduction in the mean shear bond strength of orthodontic metal brackets when bonded to human teeth treated with bleaching dentifrices.

Comparative Evaluation of Microtensile Dentin Bond Strength and Interfacial Micromorphology of Three Universal Adhesives.

OBJECTIVES: To assess and compare the microtensile dentin bond strength (µTBS) and interfacial micromorphology of three universal adhesives. METHODS: 96 human molars were assigned to three universal adhesives: Single Bond Universal (SBU), CLEARFIL Universal Bond Quick (UBQ), and RE-GEN Universal Adhesive (REGEN). Adhesives were applied in self-etch mode. SBU and REGEN were applied following the manufacturers' instructions. UBQ was divided into two subgroups: one following the manufacturer's instructions (UBQ Short) and the other with an extended application time (UBQ Extended). Teeth were restored with nanohybrid resin composite. Specimens were divided into immediate and delayed subgroups. The delayed subgroups were stored for 6 months and subjected to 5000 thermocycles. µTBS was tested, and failure mode was analyzed. Interfacial micromorphology was assessed using a scanning electron microscope. The data were statistically analyzed (p⟨ 0.05). RESULTS: The adhesive choice, aging, and their interaction significantly affected µTBS. SBU exhibited the highest immediate µTBS, comparable to UBQ (Extended) and REGEN, and significantly higher than UBQ (Short). In delayed testing, SBU outperformed the other adhesives. CONCLUSIONS: Aging negatively affected the µTBS of UBQ and REGEN, while SBU wasn't affected. The quick application concept of UBQ deteriorated its µTBS compared to the extended application time.

The effect of antimicrobial peptide-added adhesive resins on shear bond strength and the adhesive remnant index of orthodontic brackets.

OBJECTIVES: The aim of this study was to evaluate the effect of in-vivo produced Nisin which is an antimicrobial peptide (AMP) added to adhesive resin on shear bond strength (SBS) and the adhesive remnant index (ARI) of orthodontic brackets. METHODS: Bacterial AMP was produced by fermentation and the ideal AMP/Bond concentration and antimicrobial efficacy of the mixture were tested. To evaluate the SBS and ARI scores of AMP-added adhesive resins, 80 maxillary premolar teeth extracted for orthodontic purposes were used and randomly assigned into 2 groups (n = 40). Group 1: Control Group (teeth bonded with standard adhesive resin); Group 2: Experimental Group (teeth bonded with AMP-added adhesive resin). Statistical analysis was performed using the SPSS package program and applying the Mann-Whitney U and Fisher's exact tests. P < 0.05 was considered as statistically significant. RESULTS: Nisin synthesized in-vivo from Lactococcus lactis (L. lactis) (ATCC 7962) bacteria was provided to form a homogenous solution at an ideal concentration To find the minimum AMP/Bond mixture ratio that showed maximum antimicrobial activity, AMP and Bond mixtures were tested at various concentration levels between 1/160 and 1/2 (AMP/Bond). As a result, the optimum ratio was determined as 1/40. The antimicrobial efficacy of Nisin-added adhesive resin was tested against Streptococcus mutans (S. mutans) (ATCC 35,688) and Lactobacillus strains (cariogenic microorganisms). AMP formed a 2.7 cm diameter zone alone, while 1/40 AMP-bond mixture formed a 1.2 cm diameter zone. SBS values of the teeth bonded with Nisin added adhesive (17.49 ± 5.31) were significantly higher than the control group (14.54 ± 4.96) (P = 0.004). According to the four point scale, Nisin added adhesive provided a higher ARI score in favour of the adhesive and tooth compared to the control group (ARI = 3, n = 20). CONCLUSIONS: Nisin produced from L. lactis (ATCC 7962) had greater antimicrobial effects after mixing with adhesive bond against cariogenic microorganisms S. mutans (ATCC 35,688) and Lactobacillus strains. Nisin added adhesive increased shear bond strength (SBS) of orthodontic brackets and ARI scores in favor of adhesive & teeth. CLINICAL RELEVANCE: Clinicians should take into account that using Nisin-added adhesive resin in orthodontic treatments can provide prophylaxis against tooth decay, especially in patients with poor oral hygiene.

A comparative evaluation of the effect of eugenol exposure time on the bond strength of an etch-and-rinse and a self-etch adhesive to dentin: An in vitro study.

Aim: The study aimed to comparatively evaluate the effect of eugenol exposure time on the micro-shear bond strength (µ-SBS) of etch-and-rinse and a self-etch adhesive to dentin. Materials and Methods: One hundred and twelve teeth samples were prepared from bisectioning 56 freshly extracted human mandibular molars and were randomly divided into 14 subgroups of 8 samples each (n = 8). Three subgroups containing eugenol and a noneugenol-based restorative material were placed on the dentin surface and left for 24 h, 7 days, and 14 days, respectively, and were compared to a control. Two bonding systems were evaluated: one being etch-and-rinse and the other self-etch adhesive. The µ-SBS were calculated and expressed in MPa. Statistical Analysis: The data were analyzed using mixed model analysis of variance. The level of statistical significance was set at 5%. Results: There was a statistically significant reduction in the µ-SBS values when the self-etch adhesive was used, after the removal of eugenol-containing cement placed for 24 h. However, the reduction in the µ-SBS values after 7 days or 14 days was not significant. Conclusion: Exposure to eugenol containing temporary cement for 24 h significantly reduces the µ-SBS of self-etching adhesives to dentin. However, exposure for 1 week or more has minimal effects.

Comparative evaluation of push-out bond strength and mode of failure of three different obturating materials: An in vitro study.

Aim: This research aimed to assess the push-out bond strength (PBS) to dentin of three distinct obturation materials inside the root canal and identify the failure mechanism. Materials and Methods: The research used 30 undamaged human mandibular premolars. The specimens were randomly assigned to three groups, each employing a different sealer (n = 10). Group 1 used AH Plus sealer, Group 2 used GuttaFlow-2 sealer, and Group 3 used bioceramic sealer (CeraSeal). The obturation procedure was performed utilizing the single-cone method with gutta-percha. The specimens were divided into sections and loaded using a universal testing machine. Following PBS testing, every sample underwent a stereomicroscope examination, and the specific failure mechanism was documented. Results: The average PBS was greatest for AH Plus, followed by CeraSeal and Guttaflow-2. Notable disparities existed between the coronal and apical levels. Conclusion: AH Plus exhibited superior PBS qualities to root dentin compared to other sealers.

Matrix metalloproteinase inhibitors in restorative dentistry.

Matrix metalloproteinases (MMPs) have been identified as agents that disintegrate the collagen structures of dental hybrid layers, resulting in reduced restorative bond strength. Multiple MMP inhibitors (MMPIs) are known to counteract this degenerative mechanism, thereby preserving bond strength and promoting the longevity of resin-based restorations. Additionally, literature suggests that certain MMPI materials possess antimicrobial/anticariogenic properties, potentially reducing the risk of secondary caries development. Therefore, this review article aims to narrate on the integration of matrix metalloproteinase inhibitors into adhesive systems and their impact on bond strength.

Shear bond strength of orthodontic brackets to single-shade composite surfaces: An in-vitro comparative study of different surface preparations.

PURPOSE: The primary objective of this study was to determine which single-shade composite surface yielded clinically acceptable shear bond strength (SBS) to metal orthodontics brackets. The secondary objectives were to identify the best composite surface treatment to enhance SBS and determine which surface treatment produced the least surface damage at debond. METHODS: Forty dental composite samples were selected from four different manufacturers (n=160) and grouped by manufacturer, one standard multi-shade dental system (FilTek™ Supreme Ultra) and three single-shade dental composites systems (OmniChroma®, SimpliShade™ and Venus® Diamond One). Each group of forty samples was randomly divided into four sub-groups (n=10). Each sub-group was identified by the surface treatment used, hydrofluoric acid (HFA), micro-etching (MIC), or phosphoric acid (PA). Shear bond strength testing and adhesive remnant index (ARI) were performed. Statistical analyses included Kruskal-Wallis, Wilcoxon rank-sum, and two-factorial ANOVA. RESULTS: OmniChroma® had statistically significant lower shear bond strength than the other composite materials tested. The control groups had statistically significant lower shear bond strength than Group 1/HFA (P<0.001) and Group 2/MIC (P<0.001). Group 1/HFA had the lowest distribution ARI score overall, while MIC had the highest ARI score distributions. CONCLUSIONS: The results of this in-vitro study found that all tested composite materials achieved clinically acceptable shear bond strengths. The utilization of micro-etching produced higher SBS. Significant Adhesive Remnant Index scores (< 0.001) were only found for OmniChroma® without any surface preparation.

Effect of laser and coating surface treatment on the bond strength of zirconia ceramics.

OBJECTIVES: This study aims to investigate bond strength between zirconia and resin cement through surface treatments with Er: YAG laser, Nd: YAG laser, and Si-Zr coating. METHODS: Seventy-five round pre-sintered zirconia discs with a diameter of 18 mm and a thickness of 1.5 mm were prepared by a powder compactor. Fifty discs were randomly divided into five groups of 10 discs each and were subjected to five surface treatments: no treatment (control group), sandblasting with alumina particles (sandblasting group), Er: YAG laser treatment (Er: YAG laser group), Nd:YAG laser treatment (Nd: YAG laser group), and Si-Zr coating treatment (Si-Zr coating group). The discs were then bonded to composite resin columns with resin cement. The shear bond strength of each group was tested with a universal tester. Roughness tester, scanning electron microscope (SEM), and energy dispersive spectroscopy were used to analyze surface performance. RESULTS: The bond strength of the Si-Zr coating group was higher than that of the remaining groups (P<0.05). The difference in bond strength between the sandblasting group and the Er: YAG laser group was not statistically significant (P>0.05), but both of them had higher bond strength than the Nd: YAG laser group (P<0.05). The Si-Zr coating group had the highest surface roughness (P<0.05). The surface roughness of the sandblasting, Er: YAG laser, and Nd: YAG laser groups was higher than that of the control group (P<0.05), but the difference among the three groups was not statistically significant (P>0.05). SEM observations showed irregular scratches on the surface of the sandblasting group and large pits with holes on the surface of the Er: YAG and Nd: YAG laser groups. In the Er: YAG laser group, the crystal structure was replaced by a smooth surface with a large amount of microcracks due to partial melting. Complex porous structures that comprised "island-like" structures and mass pores among the grains were observed on the surface of the Si-Zr coating. Only Zr, O, and Y were detected on the surfaces of the control, Er: YAG laser, and Nd: YAG laser groups. Al was found on the surface of the sandblasted group, and a higher proportion of Si was detected on the surface of the Si-Zr coating group. CONCLUSIONS: Er: YAG laser and Nd: YAG laser treatment on the zirconia ceramic surface could increase roughness and improve the bond strength to resin cement. Si-Zr coating treatment is an effective alternative for increasing the roughness and bond strength of zirconia surface and is superior to sandblasting and laser treatments.

Effects of proanthocyanidin-functionalized hydroxyapatite nanoparticles on dentin bonding.

OBJECTIVES: To evaluate the effect of proanthocyanidin-functionalized hydroxyapatite nanoparticles (nHAp_PA) used as pretreatment at different concentrations on the microtensile bond strength (µTBS) and endogenous enzymatic activity (MMPs) on pH-cycled dentin after 24 h and 6 months of artificial aging. MATERIALS AND METHODS: Fifty human sound dentin blocks were randomly assigned to 5 groups (n = 10): (i) negative control (no treatment); (ii) positive control (pH-cycling); (iii) pH-cycling + 2% nHAp_PA for 60s; (iv) pH-cycling + 6.5% nHAp_PA for 60s; (v) pH-cycling + 15% nHAp_PA for 60s. A self-etch adhesive was used for bonding procedures before resin composite build-ups. Specimens were tested with the µTBS test after 24 h and 6 months of laboratory storage. The proteolytic activity in each group was evaluated with gelatin zymography and in situ zymography. Data were statistically analyzed (p < 0.05). RESULTS: At 24 h, the µTBS of the experimental groups were significantly higher than the controls (p ≤ 0.001), and no differences were observed between different concentrations (p > 0.05). Artificial aging significantly decreased bond strength in all groups (p ≤ 0.008); however, nHAp_PA 2% still yielded higher bonding values than controls (p ≤ 0.007). The groups pretreated with nHAp_PA exhibited lower MMP-9 and MMP-2 activities compared to the positive control group and almost the same enzymatic activity as the negative control group. In situ zymography showed that after 6 months of aging, nHAp_PA 2% and nHAp_PA 6,5% decreased enzymatic activity as well as the negative control. CONCLUSIONS: Dentin pretreatment with nHAp_PA increased the bonding performance of a self-etch adhesive and decreased MMP-2 and MMP-9 activities after 6 months.

Solvent Effect on Dative and Ionic Bond Strengths: A Unified Theory from the Potential Analysis and Valence Bond (VB) Computation.

Solvent molecules interact with a solute through various intermolecular forces. Here we employed a potential energy surface (PES) analysis to interpret the solvent-induced variations in the strengths of dative (Me3NBH3) and ionic (LiCl) bonds, which possess both ionic and covalent (neutral) characteristics. The change of a bond is driven by the gradient (force) of the solvent-solute interaction energy with respect to the focused bond length. Positive force shortens the bond length and increases the bond force constant, leading to a blue-shift of the bond stretching vibrational frequency upon solvation. Conversely, negative force elongates the bond, resulting in a reduced bond force constant and red-shift of the stretching vibrational frequency. The different responses of Me3NBH3 and LiCl to solvation are studied with valence bond (VB) theory, as Me3NBH3 and LiCl are dominated by the neutral covalent VB structure and the ionic VB structure, respectively. The dipole moment of an ionic VB structure increases along the increasing bond distance, while the dipole moment of a neutral covalent VB structure increases with the decreasing bond distance. The roles of the dominating VB structures are further examined by the geometry optimizations and frequency calculations with the block-localized wavefunction (BLW) method.

Photoactivated rose bengal-doped TiO2 nanoparticles modified fifth-generation adhesive on the survival rate of Streptococcus mutants and mechanical properties of tooth-colored restorative material to carious dentin.

Assessment of the antimicrobial, micro tensile bond strength (µTBS), and degree of conversion (DC) of fifth-generation adhesive modified using photoactivated 0.5% rose bengal (RB) and photoactivated RB-doped titanium dioxide nanoparticles (TiO2NPs) in different concentrations (2% and 5%) as compared with the unmodified adhesive bonded to the carious affected dentin (CAD). Forty mandibular molars with caries progression up to the middle third of the dentin, as per the International Caries Detection and Assessment System (ICDAS) score of 4 and 5 were included. Specimens were divided into four groups based on etch and rinse adhesive (ERA) modification group 1: unmodified ERA, group 2: photoactivated 0.5% RB photosensitizer (PS) modified ERA, group 3: photoactivated RB-doped 2 wt% TiO2NPs adhesive, group 4: photoactivated RB-doped 5 wt% TiO2NPs adhesive. Followed by adhesive and composite restoration on the CAD surface. All the specimens were thermocycled and an assessment of µTBS and failure pattern analysis was performed. The antibacterial potency of RB and RB-doped TiO2NPs (2% and 5%) followed by their activation using visible light against Streptococcus mutans (S.mutans) were tested. The survival rate of S.mutans was assessed using the Kruskal-Wallis test. The analysis of µTBS involved the use of ANOVA, followed by a post-hoc Tukey honestly significant difference (HSD) multiple comparisons test. Group 1 (Unmodified ERA) (0.52 ± 0.31 CFU/mL) treated samples unveiled the highest means of bacterial survival and lowest µTBS (11.32 ± 0.63 MPa). Nevertheless, group 4: photoactivated RB-doped 5 wt% TiO2NPs adhesive displayed the lowest outcomes of S.mutans survival (0.11 ± 0.02 CFU/mL) and highest bond strength (18.76 ± 1.45 MPa). The photoactivated RB-doped 2 wt% TiO2NPs in adhesive demonstrated promising enhancements in both µTBS and antibacterial efficacy against S.mutans. However, it is noteworthy that this modification led to a decrease in the DC of the adhesive. RESEARCH HIGHLIGHTS: Unmodified ERA-treated samples unveiled the highest bacterial survival and the lowest µTBS. Photoactivated RB-doped 5 wt% TiO2NPs adhesive displayed the lowest S.mutans survival rate and highest bond strength. DC decreased with an increase in concentration of TiO2.

Adhesive Performance of Pit and Fissure Sealants on Deproteinized Enamel with Different Proteolytic Agents: In Vitro Study.

The objective of this work was to assess the efficacy of different proteolytic agents on the bond strength of pit and fissure sealants to bovine enamel. Eighty-four bovine enamel specimens were randomly assigned in groups according to the pit and fissure sealant applied (HelioSeal F or Dyad Flow). Then, the specimens were subdivided according to the proteolytic agent used (n = 7): Group 1, distilled water (control); Group 2, 10 wt.% Tergazyme®; Group 3, 10 wt.% ZYME®; Group 4, 10% papain gel; Group 5, 10% bromelain gel; and Group 6, 5.25 wt.% sodium hypochlorite. The cell viability of the proteolytic solutions was assessed through the MTT assay. The proteolytic agents were applied on the enamel surface prior to the acid-etching procedure; then, the pit and fissure sealants were placed. The micro-shear bond strength was evaluated after 24 h or 6 months of water storing at 37 °C. Representative SEM images were taken for each experimental group. The bond strength data were statistically analyzed by a three-way ANOVA test using a significance level of α = 0.05. Bromelain and papain proteolytic solutions did not exert any cytotoxic effect on the human dental pulp cells. After 24 h and 6 months of aging, for both pit and fissure sealants, sodium hypochlorite, papain, bromelain, and Tergazyme® achieved statistically significant higher bond strength values (p < 0.05). Irrespective of the deproteinizing agent used, Dyad Flow resulted in a better bond strength after 6 months of aging. The type 1 etching pattern was identified for sodium hypochlorite, papain, and bromelain. Tergazyme®, papain, and bromelain demonstrated efficacy in deproteinizing enamel surfaces prior to acid etching, leading to the improved bond strength of pit and fissure sealants. Clinically, this suggests that these proteolytic agents can be considered viable alternatives to traditional methods for enhancing sealant retention and longevity. Utilizing these agents in dental practice could potentially reduce sealant failures.

Bonding Effectiveness of Veneering Ceramic to Zirconia after Different Grit-Blasting Treatments.

Objective: To determine the effect of grit-blasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar) were divided into four test groups of three specimens each and a control group ('CTR'; no surface treatment). Pre-S-30, Pre-S-50, and Pre-S-110 were grit-blasted with 30-µm SiO2-coated Al2O3, 50-µm Al2O3 and 110-µm Al2O3 particles, respectively, before sintering. Post-S-30 was grit-blasted with 30-µm SiO2-coated Al2O3 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner was applied and a pressable ceramic (IPS e.max ZirPress, Ivoclar) was heat-pressed. Sixteen microbars were obtained from each block and submitted to micro-tensile bond-strength (µTBS) testing. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Grit-blasting before sintering with 110-µm Al2O3 (RaPre-S-110 = 3.4 ± 0.4 µm), 50-µm Al2O3 (RaPre-S-50 = 2.3 ± 0.5 µm), and 30-µm SiO2-coated Al2O3 (RaPre-S-30 = 1.2 ± 0.2 µm) resulted in significantly higher roughness than grit-blasting after sintering with 30-µm SiO2-coated Al2O3 (RaPost-S-30 = 0.5 ± 0.1 µm). The highest µTBS was measured when the sintered zirconia was grit-blasted with 30-µm SiO2-coated Al2O3 (µTBSPost-S-30 = 28.5 ± 12.6 MPa), which was significantly different from that of specimens that were grit-blasted before sintering (µTBSPre-S-30 = 21.8 ± 10.4; µTBSPre-S-50 = 24.1 ± 12.6; µTBSPre-S-110 = 26.4 ± 14.1) or were not grit-blasted (µTBSCTR = 20.2 ± 11.2). Conclusions: Grit-blasting zirconia before sintering enhanced the surface roughness proportionally to the particle size of the sand used. Grit-blasting with 30-µm SiO2-coated Al2O3 after sintering improved bonding of the veneering ceramic to zirconia. Clinical Significance: As grit-blasting with 30-µm SiO2-coated Al2O3 after sintering improved bonding of the veneering ceramic to zirconia, it may reduce veneering ceramic fractures/chipping.

Effect of Photodynamic Therapy with Four Light-Sensitive Materials on the Bond Strength of Fiber Posts to Root Dentin.

Introduction: Fiber-reinforced composite posts (FRCP) have become popular due to their multiple advantages in teeth with extensive crown destruction. Proper disinfection is essential for the successful bonding of these posts. Commonly used solutions for cleaning and disinfecting the root canals adversely affect the bond strength (BS). Photodynamic therapy is an alternative method for irrigating the root canal and disinfecting the post space.This study was designed to evaluate the impact of photodynamic therapy on the BS of fiber posts to root canal dentin. Methods: Human maxillary canines were recruited for this study. The tooth crowns were removed at the cervical line and endodontically treated. After fiber post spaces were prepared, the teeth were assigned to five groups based on the light-sensitive material: deionized water, indocyanine green and 810-nm laser, methylene blue and 660-nm laser, toluidine blue and 635-nm laser, curcumin and LED. The posts were cemented after photodynamic therapy. Cervical, middle, and apical samples were prepared by transverse sectioning. Push-out bond strength (PBS) values were measured in a universal testing machine. Finally, the data underwent statistical analyses with ANOVA and Howell-Games tests. Results: One-way ANOVA revealed no significant differences between the groups (P<0.001). The Games-Howell test showed that curcumin (7.23±3.75) and the control group (5.92±4.04) had a similar BS (P>0.005). The BS was lower in the methylene blue (3.34±2.15), indocyanine green (2.59±3.16), and toluidine blue (2.45±1.73) groups than in the control group (P<0.005). Conclusion: Unlike other light-sensitive materials, curcumin did not adversely affect the BS.

Assessment of the Additive Effect of Remineralizing Agents in Combination With Fluoride Releasing Adhesives in the Prevention of Enamel Decalcification in Orthodontic Patients: An In Vitro Study.

Introduction Incorporation of remineralizing agents with fluoride-releasing bracket adhesives may prevent the development of white spot lesions (WSL) or reverse the established WSL in patients undergoing fixed orthodontic treatment. We aimed to find out how effectively casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and fluoride varnish (FV) can remineralize teeth when mixed with fluoride-releasing orthodontic adhesive. Materials and methods We randomly assigned a total of 60 premolar teeth, therapeutically extracted for orthodontic purposes, into two equal groups. Group I (n = 30) utilized fluoride-releasing adhesive (FR), and Group II (n = 30) bonded with non-fluoride adhesive (NFR). Based on the applied remineralizing agent, we further divided each of the two groups into three equal subgroups of 10: Group IA (FR+FV), Group IB (FR+CPP-ACP), Group IC (control-only FR), Group IIA (NFR+FV), Group IIB (NFR+CPP-ACP), and Group IIC (control-only NFR). Following bonding procedures, all the samples underwent pH cycling for 28 days, where the enamel samples were immersed in 20 ml of demineralizing solution for three hours, followed by immersion in 30 ml of remineralizing solution for 17 hours. The samples were analyzed for shear bond strength (SBS) on a universal testing machine and hardness values (HV) by the Vickers microhardness test (VMT) using the indentation method. We also evaluated the adhesive remnant index (ARI) scores to determine the site of bracket failure. Statistical analysis The shear bond strength (SBS) and hardness value (HV) were expressed as the mean, standard deviation (SD), and median for each subgroup. We used the non-parametric Kruskal-Wallis test to analyze the SBS and HV, followed by the Dunn-Bonferroni test for intra-pair differences. The ARI score was expressed as the frequency of the percentage distribution, and the difference in the distribution of ARI scores between the groups was assessed by the Cochran chi-square test. The probability (p) value equal to or less than 0.05 was considered statistically significant. Results The results show that Group IB, bonded with a fluoride-releasing adhesive and a CPP-ACP remineralizing agent surface treatment, has the highest HV of 300.23 units. Group IIC (only NFR) has the lowest hardness of 153.3 units, which is statistically significant (p < 0.001). However, the ARI scores are not statistically significant between the groups tested. Conclusion The bond strength of the adhesive and the surface hardness of the enamel increased with the addition of fluoride varnish and CPP-ACP to both the fluoride-releasing and non-fluoride-releasing adhesives.