Fluid inertia controls mineral precipitation and clogging in pore to network-scale flows.

Mineral precipitation caused by fluid mixing presents complex control and predictability challenges in a variety of natural and engineering processes, including carbon mineralization, geothermal energy, and microfluidics. Precipitation dynamics, particularly under the influence of fluid flow, remain poorly understood. Combining microfluidic experiments and three-dimensional reactive transport simulations, we demonstrate that fluid inertia controls mineral precipitation and clogging at flow intersections, even in laminar flows. We observe distinct precipitation regimes as a function of Reynolds number (Re). At low Reynolds numbers (Re < 10), precipitates form a thin, dense layer along the mixing interface, which shuts precipitation off, while at high Reynolds numbers (Re > 50), strong three-dimensional flows significantly enhance precipitation over the entire intersection, resulting in rapid clogging. When injection rates from two inlets are uneven, flow symmetry-breaking leads to unexpected flow bifurcation phenomena, which result in enhanced concurrent precipitation in both downstream channels. Finally, we extend our findings to rough channel networks and demonstrate that the identified inertial effects on precipitation at the intersection scale are also present and even more dramatic at the network scale. This study sheds light on the fundamental mechanisms underlying mixing-induced mineral precipitation and provides a framework for designing and optimizing processes involving mineral precipitation.

A difficult coexistence: Resolving the iron-induced nitrification delay in groundwater filters.

Rapid sand filters (RSF) are an established and widely applied technology for the removal of dissolved iron (Fe2+) and ammonium (NH4+) among other contaminants in groundwater treatment. Most often, biological NH4+oxidation is spatially delayed and starts only upon complete Fe2+ depletion. However, the mechanism(s) responsible for the inhibition of NH4+oxidation by Fe2+ or its oxidation (by)products remains elusive, hindering further process control and optimization. We used batch assays, lab-scale columns, and full-scale filter characterizations to resolve the individual impact of the main Fe2+ oxidizing mechanisms and the resulting products on biological NH4+ oxidation. modeling of the obtained datasets allowed to quantitatively assess the hydraulic implications of Fe2+ oxidation. Dissolved Fe2+ and the reactive oxygen species formed as byproducts during Fe2+ oxidation had no direct effect on ammonia oxidation. The Fe3+ oxides on the sand grain coating, commonly assumed to be the main cause for inhibited ammonia oxidation, seemed instead to enhance it. modeling allowed to exclude mass transfer limitations induced by accumulation of iron flocs and consequent filter clogging as the cause for delayed ammonia oxidation. We unequivocally identify the inhibition of NH4+oxidizing organisms by the Fe3+ flocs generated during Fe2+ oxidation as the main cause for the commonly observed spatial delay in ammonia oxidation. The addition of Fe3+ flocs inhibited NH4+oxidation both in batch and column tests, and the removal of Fe3+ flocs by backwashing completely re-established the NH4+removal capacity, suggesting that the inhibition is reversible. In conclusion, our findings not only identify the iron form that causes the inhibition, albeit the biological mechanism remains to be identified, but also highlight the ecological importance of iron cycling in nitrifying environments.

Application of therapeutic ultrasonic waves across the dialyzer membrane: A pilot study on the impact on dialyzer clearance and safety.

INTRODUCTION: Progressive clogging of the dialyzer membrane during hemodialysis can compromise solute removal efficiency. Existing solutions fall short in addressing intradialytic reduction of dialyzer clearance. This pilot study aims to assess the impact and safety of applying therapeutic ultrasonic waves to dialyzers for mitigating intradialytic clogging. METHODS: In this pilot study, 15 stable maintenance hemodialysis patients (12 males and 3 females) were enrolled. Each patient served as their own control. They underwent one session of hemodialysis with the application of therapeutic ultrasonic waves (Ultrasonic session) and were crossed-over to a second session without the use of ultrasonic waves (Control session). All the study sessions operated at a fixed dialysate flow rate of 500 mL/min and a blood flow rate of 250 or 300 mL/min. The adequacy of dialysis achieved during each session was monitored using Online Clearance Monitoring of the dialysis machines, and clearance K values, varying between 135 and 209 mL/min, were recorded, and plotted. A direct comparison between Control and Ultrasonic sessions was performed to assess the impact and safety of using ultrasonic waves during hemodialysis. FINDINGS: The mean percentage decline in dialyzer clearance values was 4.41% for Ultrasonic sessions (SD: 5.3) and 12.69% for Control sessions (SD: 6.35) (p-value <0.001). This indicates that the application of ultrasonic waves reduced the decline in clearance values. The mean differences of the blood component parameters were comparable between both Ultrasonic sessions and Control sessions, suggesting the safety of utilizing ultrasonic waves during dialysis. Microscopic membrane analysis corroborated the safety. DISCUSSION: Intradialytic clogging of dialyzer membranes is a significant problem that can cause dialysis inadequacy. Our study tackles this issue by introducing therapeutic ultrasonic waves to improve dialyzer clearance during hemodialysis sessions in patients.

Study on Mudcake disintegration in clayey strata during shield tunneling: Effects of dispersants and bentonite slurry.

While tunnel boring machines (TBMs) tunneling in clayey strata, the adhered excavated soil on the cutterhead and cutting tools tends to form mudcake after compaction and consolidation. Mudcake can obstruct the cutterhead openings and rendering the cutting tools ineffective, leads to a substantial reduction in advance rate. Dispersants are recognized as an effective method for the disintegration of mudcakes. A novel set of equipment, comprising a mudcake compression device and a mudcake disintegration apparatus, is developed for assessing mudcake disintegration properties. The results showed that mudcakes underwent a tripartite disintegration process in water, including an initial stage, a rapid disintegration stage, and a stable stage. In the initial stage, the mudcakes absorbed water before disintegration, resulting in marginal changes in the weight of the disintegrated mudcakes. In the rapid disintegration stage, the weight of the disintegrated mudcakes increased quickly. During the stable stage, the weight of the disintegrated mudcakes remained relatively constant. The submersion of mudcakes in a dispersant solution substantially increased the rate of disintegration. Greater dispersant concentration corresponded to an increase in the disintegration rate. No weight gain was observed in mudcakes during the initial disintegration stage. When mudcakes disintegrated in a bentonite slurry, the weight of the disintegrated mudcakes initially decreased and then stabilized. The weight of the disintegrated mudcakes turned negative, indicating an increase in the weight of mudcakes. This suggested that bentonite significantly hindered mudcake disintegration.

Photocell-Based Optofluidic Device for Clogging-Free Cell Transit Time Measurements.

Measuring the transit time of a cell forced through a bottleneck is one of the most widely used techniques for the study of cell deformability in flow. It in turn provides an accessible and rapid way of obtaining crucial information regarding cell physiology. Many techniques are currently being investigated to reliably retrieve this time, but their translation to diagnostic-oriented devices is often hampered by their complexity, lack of robustness, and the bulky external equipment required. Herein, we demonstrate the benefits of coupling microfluidics with an optical method, like photocells, to measure the transit time. We exploit the femtosecond laser irradiation followed by chemical etching (FLICE) fabrication technique to build a monolithic 3D device capable of detecting cells flowing through a 3D non-deformable constriction which is fully buried in a fused silica substrate. We validated our chip by measuring the transit times of pristine breast cancer cells (MCF-7) and MCF-7 cells treated with Latrunculin A, a drug typically used to increase their deformability. A difference in transit times can be assessed without the need for complex external instrumentation and/or demanding computational efforts. The high throughput (4000-10,000 cells/min), ease of use, and clogging-free operation of our device bring this approach much closer to real scenarios.

Unraveling Pre-filled Syringe Needle Clogging: Exploring a Fresh Outlook Through Innovative Techniques.

OBJECTIVE: This study aimed to investigate the movement of liquid in the needle region of staked-in-needle pre-filled syringes using neutron imaging and synchrotron X-ray tomography. The objective was to gain insights into the dynamics of liquid presence and understand the factors contributing to needle clogging. METHODS: Staked-in-needle pre-filled syringes were examined using neutron radiography and synchrotron X-ray phase-contrast computed tomography. Neutron radiography provided a 2D visualization of liquid presence in the needle, while synchrotron X-ray tomography offered high-resolution 3D imaging to study detailed morphological features of the liquid. RESULTS: Neutron radiography revealed liquid presence in the needle region for as-received samples and after temperature and pressure cycling. Pressure cycling had a more pronounced effect on liquid formation. Synchrotron X-ray tomography confirmed the presence of liquid and revealed various morphologies, including droplets of different sizes, liquid segments blocking sections of the needle, and a thin layer covering the needle wall. Liquid presence was also observed between the steel needle and the glass barrel. CONCLUSIONS: The combination of neutron imaging and synchrotron X-ray tomography provided valuable insights into the dynamics of liquid movement in staked-in-needle pre-filled syringes. Temperature and pressure cycling were found to contribute to additional liquid formation, with pressure changes playing a significant role. The detailed morphological analysis enhanced the understanding of microstructural arrangements within the needle. This research contributes to addressing the issue of needle clogging and can guide the development of strategies to improve pre-filled syringe performance.

Using organic fertilizer to mitigate organic-inorganic fouling in agricultural saline wastewater irrigation systems.

Recycling saline wastewater for agricultural irrigation offer a promising solution to address both water scarcity and anthropogenic pollution. However, organic-inorganic fouling in saline wastewater irrigation systems (SWIS) poses significant technical and economic challenges. Traditional chemical biocides are currently insufficient for controlling composite organic-inorganic fouling and may pose environmental hazards. This study proposed a greener approach using organic acid (OA) fertilizers to alleviate organic-inorganic fouling in agricultural SWIS. The treatment performances were assessed employing four types of OA fertilizers (i.e., humic acid, alginic acid, nucleotide, and ammonia acid) and a negative control. Results showed that three types of OA, i.e., alginic acid, nucleotide, and ammonia acid, effectively reduced the total SWIS fouling content by 11.2%-57.4%, whereas humic acid exacerbated fouling by 11.2%-57.4%. Specifically, all types of OA significantly mitigated the content of inorganic fouling (precipitates and silicates) by 10.7%-42.3% by forming loosed and sparser structures. However, OA exhibited minimum effects on controlling silica fouling. Meanwhile, except the humic acid, other types of OA decreased the total content of organic fouling by 17.2%-39.5% by reducing the content of humic substances and building block fractions. In addition, the significant binary interactions of organic-inorganic fouling indicated the active role of calcium silica and biomineralization fouling. These findings provide insight into the development of appropriate and eco-friendly antifouling strategies for SWIS, with implications for recycling and reusing saline wastewater.

Size-based analysis of virus removal filter fouling using fractionated protein aggregates.

Fouling by protein aggregates reduces virus removal filter performance. In the present study, we investigated the effects of different-sized protein aggregates on fouling and aggregate retention in order to better understand the fouling mechanisms. Human immunoglobulin G was denatured by heating to produce aggregates of various sizes and then fractionated by size exclusion chromatography into different-sized aggregates with a narrow size distribution. The fractionated aggregates were filtered on Planova 20N, a virus removal filter known for its stable filtration capability. Analysis of flux behavior demonstrated different flux decrease patterns for different-sized aggregates. Observation of aggregate retention by staining revealed that larger aggregates were captured closer to the inner surface of the membrane while smaller aggregates penetrated farther into the membrane. These findings demonstrate that Planova 20N has a gradient structure with decreasing pore size from the inner to the outer surface of the membrane. This structure minimizes fouling and enables stable filtration by protecting the smaller pores located closer to the outer surface from clogging by large aggregates. Applying the predominant clogging models to the present filtrations revealed that clogging behavior transitioned from complete blocking to cake filtration as filtration progressed. In this combination model, after a certain number of pores are blocked by complete blocking, newly arrived aggregates begin to accumulate on previously captured aggregates, generating cake between capture layers within the membrane. Application of the approaches described here will facilitate elucidation of membrane fouling and virus removal mechanisms.

CFD-DEM study on transport and retention behaviors of nZVI-clay colloids in porous media.

Transportation process of nano scale zero valent iron (nZVI) in clay-rich soils is complicated and crucial for in-situ remediation of contaminated sites. A coupled computational fluid dynamic and discrete element method (CFD-DEM) was used to investigate the interplays of repulsive and attractive forces and the injection velocity of this process. The screened Coulomb's law was used to represent the electrostatic interaction, and surface energy density was introduced to represent the effects of the van der Waals interaction. A phase diagram was constructed to describe the interplay between injection velocity and repulsive force (in terms of charge of colloids). Under the boundary and initial conditions in this study, clogging formed at low repulsive force (colloidal charge = -1 ×10-15 C), where increment of injection velocity (from 0.002 m/s to 0.02 m/s) cannot prevent clogging, as in the case of bare nZVI transportation with limited mobility; On the other hand, excessive repulsive force (charge = -4 ×10-14 C) is detrimental to nZVI-clay transportation due to repulsion from the concentrated colloids in pore throats, a phenomenon as in the overuse of stabilizers and was defined as the "membrane repulsion effect" in this study. At moderate charge (-1 ×10-14 C), injection velocity increment induced clogging due to aggregates formed at the windward of cylinder and accumulated at the pore throats.

What to consider for successful administration of oral liquids via enteral feeding tubes? a case study with paediatric ibuprofen suspensions.

Administration of medications via enteral feeding tubes (EFTs) is a common practice for children who cannot swallow properly. Although liquid formulations are the preferred dosage forms for this route of administration, little attention has been paid to the amount of drug that reaches the site of absorption after administration via an EFT. This systematic in vitro study aimed to identify formulation parameters and administration approaches that are critical for successful dose delivery via EFTs. For this purpose, drug recovery after administration of three different paediatric ibuprofen suspensions via different types of EFTs was studied using derivative UV spectrophotometry for quantification. Study results indicate that in addition to formulation parameters, feeding tube characteristics and the administration process can have a significant impact on the administered dose. The ratio between the total administered fluid volume (TAV), represented by the sum of dose- and flushing volume, and the feeding tube volume (FTV) proved to be a valuable indicator for assessing successful administration. Incorrect dosing and complications could be avoided if the TAV/FTV ratio was greater than 4. This and other knowledge gained in the study will help to make the administration of liquid paediatric medicines via EFTs both more effective and safer.

Preparing Enteral Formulas for Adult Patients with Phenylketonuria: A Minor Necessity but Major Challenge-A Case Report.

Phenylketonuria (PKU) is the most frequent of the congenital errors of amino acid (AA) metabolism worldwide. It leads to the accumulation of the essential AA phenylalanine (Phe) and it is associated with severe neurological defects. The early diagnosis and treatment of this rare disease, achieved through newborn screening and low-Phe diet, has profoundly changed its clinical spectrum, resulting in normal cognitive development. We face the first generation of PKU patients perinatally diagnosed and treated who have reached adulthood, whose special needs must be addressed, including feeding through enteral nutrition (EN). However, recommendations regarding EN in PKU constitute a gap in the literature. Although protein substitutes for patients with PKU are offered in multiple forms (Phe-free L-amino acid or casein glycomacropeptide supplements), none of these commercial formulas ensures the whole provision of daily total energy and protein requirements, including a safe amount of Phe. Consequently, the combination of different products becomes necessary when artificial nutrition via tube feeding is required. Importantly, the composition of these specific formulas may result in physicochemical interactions when they are mixed with standard EN products, leading to enteral feeding tubes clogging, and also gastrointestinal concerns due to hyperosmolality. Herein, we present the first reported case of EN use in an adult patient with PKU, where the separate administration of protein substitutes and the other EN products avoided physicochemical interactions.

Structural and functional perspectives of carbon filter media in constructed wetlands for pollutants abatement from wastewater.

Constructed wetlands (CWs) represent the most viable artificial wastewater treatment system that works on the principles of natural wetlands. Filter media are integrally linked to CWs and have substantial impacts on their performance for pollutant removal. Carbon-derived substrates have been in the spotlight for decades due to their abundance, sustainability, reusability, and potential to treat complex contaminants. However, the efficiency and feasibility of carbon substrates have not been fully explored, and there are only a few studies that have rigorously analyzed their performance for wastewater treatment. This critical synthesis of the literature review offers comprehensive insights into the utilization of carbon-derived substrates in the context of pollutant removal, intending to enhance the efficiency and sustainability of CWs. It also compares several carbon-based substrates with non-carbon substrates with respect to physiochemical properties, pollutant removal efficiency, and cost-benefit analysis. Furthermore, it addresses the concerns and possible remedies about carbon filtration materials such as configuration, clogging minimization, modification, and reusability to improve the efficacy of substrates and CWs. Recommendations made to address these challenges include pretreatment of wastewater, use of a substrate with smaller pore size, incorporation of multiple filter media, the introduction of earthworms, and cultivation of plants. A current scientific scenario has been presented for identifying the research gaps to investigate the functional mechanisms of modified carbon substrates and their interaction with other CW components.

Spatial-temporal clogging development in leachate collection systems of landfills: Insight into chemical and biological clogging characteristics.

The clogging of leachate collection systems (LCSs) is a typical challenge for landfills operation. Although clogging occurs in different LCS components, its spatial-temporal distributions remain unclear. This study aimed to systematically investigate the dynamic clogging development in simulated LCSs by monitoring changes in clogging characteristics over time. Results revealed that clogging accumulated in all components of the simulated LCS during a 215-day period, including chemical clogging and bio-clogging. Distinct spatial variations in clogging components were observed along the leachate flow of the simulated LCS, with the geotextile being severely clogged due to bio-clogging (70.1 ± 3.0%-80.0 ± 0.5%). Additionally, chemical clogging mainly occurred at the top (85.4 ± 0.8%-95.0 ± 0.9%) and middle (91.2 ± 0.8%-94.9 ± 1.1%) gravel layers. Nevertheless, the percentage of chemical clogging decreased from 72.0 ± 2.1% (day 42) to 42.5 ± 2.7% (day 215) at the bottom gravel layer. Chemical clogging was the main type in the pipe, accounting for 69.6 ± 0.5% (day 215). In addition, the ratios of bio-clogging to chemical clogging changed over time in all LCS components. The spatial-temporal characteristics of clogging across LCS components can enhance the understanding of clogging mechanisms, facilitate the design optimization of LCSs, and promote the formulation of effective control strategies.

Fault Detection in 3D Printing: A Study on Sensor Positioning and Vibrational Patterns.

This work examines the use of accelerometers to identify vibrational patterns that can effectively predict the state of a 3D printer, which could be useful for predictive maintenance. Prototypes using both a simple rectangular shape and a more complex Octopus shape were fabricated and evaluated. Fast Fourier Transform, Spectrogram, and machine learning models, such as Principal Component Analysis and Support Vector Machine, were employed for data analysis. The results indicate that vibrational signals can be used to predict the state of a 3D printer. However, the position of the accelerometers is crucial for vibration-based fault detection. Specifically, the sensor closest to the nozzle could predict the state of the 3D printer faster at a 71% greater sensitivity compared to sensors mounted on the frame and print bed. Therefore, the model presented in this study is appropriate for vibrational fault detection in 3D printers.

Signal sequence-triage is activated by translocon obstruction sensed by an ER stress sensor IRE1α.

Secretory pathway proteins are cotranslationally translocated into the endoplasmic reticulum (ER) of metazoan cells through the protein channel, translocon. Given that there are far fewer translocons than ribosomes in a cell, it is essential that secretory protein-translating ribosomes only occupy translocons transiently. Therefore, if translocons are obstructed by ribosomes stalled or slowed in translational elongation, it possibly results in deleterious consequences to cellular function. Hence, we investigated how translocon clogging by stalled ribosomes affects mammalian cells. First, we constructed ER-destined translational arrest proteins (ER-TAP) as an artificial protein that clogged the translocon in the ER membrane. Here, we show that the translocon clogging by ER-TAP expression activates triage of signal sequences (SS) in which secretory pathway proteins harboring highly efficient SS are preferentially translocated into the ER lumen. Interestingly, the translocon obstructed status specifically activates inositol requiring enzyme 1α (IRE1α) but not protein kinase R-like ER kinase (PERK). Given that the IRE1α-XBP1 pathway mainly induces the translocon components, our discovery implies that lowered availability of translocon activates IRE1α, which induces translocon itself. This results in rebalance between protein influx into the ER and the cellular translocation capacity.Key words: endoplasmic reticulum, translocation capacity, translocon clogging, IRE1, signal sequence.

Exploring Digital Twin-Based Fault Monitoring: Challenges and Opportunities.

High efficiency and safety are critical factors in ensuring the optimal performance and reliability of systems and equipment across various industries. Fault monitoring (FM) techniques play a pivotal role in this regard by continuously monitoring system performance and identifying the presence of faults or abnormalities. However, traditional FM methods face limitations in fully capturing the complex interactions within a system and providing real-time monitoring capabilities. To overcome these challenges, Digital Twin (DT) technology has emerged as a promising solution to enhance existing FM practices. By creating a virtual replica or digital copy of a physical equipment or system, DT offers the potential to revolutionize fault monitoring approaches. This paper aims to explore and discuss the diverse range of predictive methods utilized in DT and their implementations in FM across industries. Furthermore, it will showcase successful implementations of DT in FM across a wide array of industries, including manufacturing, energy, transportation, and healthcare. The utilization of DT in FM enables a comprehensive understanding of system behavior and performance by leveraging real-time data, advanced analytics, and machine learning algorithms. By integrating physical and virtual components, DT facilitates the monitoring and prediction of faults, providing valuable insights into the system's health and enabling proactive maintenance and decision making.

Hydrodynamics and effect of velocity on particle filtration due to bridging in water-saturated porous media using CFD-DEM simulation.

Particle bridging owing to the confinement of the pore structure affects the transport and retention of particles in porous media. Particle motion driven by gravities were well investigated, whose filtration is mainly affected by the ratio of the particle diameter to the pore throat size of the medium. However, particles whose motions are driven by the fluid is essential to be investigated for particle separation from the carrying fluid. In this study, the motion of particles was driven by the liquid when passing through a water-saturated porous medium. The fluid-particle flow in a porous medium was modeled using computational fluid dynamics-discrete element method. The motion of particles in the slurry was traced in the porous medium, which enabled particle clogging to be directly precited by the interaction between the particles and pore surfaces by assessing the exact location of each particle. The pressure and flow field of the liquid were investigated, and the variation in flow path owing to particle clogging was predicted. The hydrodynamic study also showed that the Stokes number and particle concentration determined the particle clogging at the pore throats of the porous medium. Increasing the fluid velocity of particles such that the Stokes number was almost equal to 1 increased the separation efficiency of particles. Further increasing the fluid velocity reduced the residence time, which reduced the separation efficiency of the particles.

Development of Electrodeposited Wire Mesh Grinding Wheel for Cutoff and Grooving Carbon Fiber Reinforced Plastic.

Carbon fiber reinforced plastic (CFRP) is used in various industries because of its high specific strength, but it is well known as a difficult material to cut. In this study, we developed a disc-shaped electrodeposited diamond wire mesh grinding wheel as a new method for cutoff and grooving with a large aspect ratio for CFRP. We confirmed that this tool could be used for machining at a feed rate of 1000 mm/min, equivalent to that of an abrasive waterjet. This tool discharges generated chips through the spaces in the wire mesh, preventing clogging and thereby enabling the suppression of machining temperature. No burrs or delamination were observed on the surface machined with the wire mesh grinding wheel, and the surface roughness was Ra = 2.76 µm. However, the groove width was larger than the wheel thickness due to the runout of the wheel. Additionally, the moderate elasticity and durability of the tool suggest that it might extend tool life by avoiding the crushing of abrasive grains.

Effect of electrodialysis on colloidal geometry and dynamics: Why my membrane stack was clogged even after a fine pretreatment?

As a long-standing problem, electrodialysis (ED) clogging is believed a consequence of colloids. However, its blocking causation and clogging mechanism have not been verified. In this study, electrodialysis was used to treat a colloidal saline solution, aiming to answer the question from the "nature" of ED by investigating the influence of ED parameters such as laminar flow, salt concentration, current density and pH on colloid geometry and dynamics during the desalting process. The results revealed that: (i) laminar and membrane electrostatic repulsion and adsorption could not significantly increase the particle size (maximum 2.28 times), while the applied electric field elevated the particle size by 54.52 times (119.9 ± 13.66 to 6537.5 ± 64.35 nm); (ii) when the initial feed concentration elevated 10 times (0.1 to 1 mol/L NaCl), the particle size upsurged 149-fold (5.99 ± 0.57 to >150 µm), and flocs were generated. This enhancement was mainly attributed to the compressive electric double layer effect, and the Debye length was trimmed from 0.96 to 0.30 nm; (iii) The low current density (25 A/m2) had a profound aggregation effect on small BSA particles (roughly 10 nm); (iv) The change of pH causes the conformational transition of BSA. In the strong acidic (pH = 3.0) environment, the colloidal particle size expanded by 13 times. This study confirmed that the aggregation of colloids was the culprit of spacer clogging during electrodialysis at higher salt concentrations (>1 mol/L). Furthermore, experimental data were substituted into the simulation formula to summarise the geometry and dynamic variation of BSA in ED.

Role of Soil Biofilms in Clogging and Fate of Pharmaceuticals: A Laboratory-Scale Column Experiment.

Contamination of groundwater with pharmaceutical active compounds (PhACs) increased over the last decades. Potential pathways of PhACs to groundwater include techniques such as irrigation, managed aquifer recharge, or bank filtration as well as natural processes such as losing streams of PhACs-loaded source waters. Usually, these systems are characterized by redox-active zones, where microorganisms grow and become immobilized by the formation of biofilms, structures that colonize the pore space and decrease the infiltration capacities, a phenomenon known as bioclogging. The goal of this work is to gain a deeper understanding of the influence of soil biofilms on hydraulic conductivity reduction and the fate of PhACs in the subsurface. For this purpose, we selected three PhACs with different physicochemical properties (carbamazepine, diclofenac, and metoprolol) and performed batch and column experiments using a natural soil, as it is and with the organic matter removed, under different biological conditions. We observed enhanced sorption and biodegradation for all PhACs in the system with higher biological activity. Bioclogging was more prevalent in the absence of organic matter. Our results differ from works using artificial porous media and thus reveal the importance of utilizing natural soils with organic matter in studies designed to assess the role of soil biofilms in bioclogging and the fate of PhACs in soils.