A systematic comparison of four pharmacopoeial methods for measuring powder flowability.

Powder flow is one of the crucial factors affecting several pharmaceutical manufacturing processes. Problems due to insufficient powder flow reduce production process efficiency and cause suboptimum product quality. The U.S. Pharmacopoeia has specified four methods to evaluate the flowability of pharmaceutical powders, including angle of repose (AoR), compressibility index (CI) and Hausner ratio (HR), Flow through an orifice, and shear cell. Comparison within and between those methods with 21 powders (covering a wide range of flowability) was performed in this study. Strong correlation was observed between fixed base cone AoR, and fixed height cone AoR (R2 = 0.939). CI and HR values calculated from a tapped density tester (meeting USP standards), manual tapping, and Geopyc® correlated strongly (R2 > 0.9). AoR, CI/HR, minimum diameter for flowing through an orifice (dmin), and shear cell results generally correlate strongly for materials with flowability worse than Avicel® PH102. Both shear cell and CI/HR methods can reliably distinguish powders exhibiting poor flow. For materials with good flow, the ability to distinguish powders follows the order of AoR ≈ CI/HR > shear cell > dmin. The systematic comparison of the four common methods provides useful information to guide the selection of methods for future powder flow characterization. Given the limitations observed in all four methods, we recommend that multiple techniques should be used, when possible, to more holistically characterize the flowability of a wide range of powders.

Orthogonal experimental study on the compressibility characteristics of bank sandy silt based on freeze-thaw effects.

The compressibility of bank soils is a critical consideration in t riverbank protection project, construction. In the Inner Mongolia section of the Yellow River, a seasonal frozen soil region, the impact of F-T cycles on soil compressibility cannot be overlooked. This study, based on F-T cycle tests, conducted orthogonal consolidation tests on embankment sandy silt from the Inner Mongolia section of the Yellow River, considering varying initial w and ρd. It investigated the effects of different initial w, ρd, and F-T cycles on soil compressibility, ranked and assessed the significance of influencing factors, and established a predictive model for the compressibility of Inner Mongolia section Yellow River embankment sandy silt. The results show that: the embankment sandy silt is medium-high compression soil, with a between 0.1 and 0.74 MPa-1, Es between 2.65 and 18.47 MPa, and Cc between 0.04 and 0.24 MPa. The greater the ρd of soil, the smaller the initial w, the smaller the a and Cc, and the greater the Es of soil. The F-T effect affects soil compressibility, and soil a, Es and Cc are linearly related to the number of F-T cycles. The ranking of factors influencing soil compressibility is ρd > w > F-T cycles. The initial ρd and w are decisive factors affecting soil compressibility, while the impact of F-T cycles is relatively minor. Additionally, a regression predictive model based on the initial ρd and w of the soil demonstrates good performance in predicting soil compression indices. This model can be utilized for predicting the compressibility indices of embankment soil in the Inner Mongolia section of the Yellow River.

A sustainable carbon aerogel from waste paper with exceptional performance for antibiotics removal from water.

In this work, a sustainable 3D carbon aerogel (AO-WPC) is prepared from waste paper (WP), and used for efficient antibiotics removal from water. The AO-WPC aerogel shows good mechanical property and can recover after 100th of 30 % compression strain. The specific surface area of AO-WPC aerogel is up to 654.58 m2/g. More importantly, this aerogel reveals proper pore size distribution, including micro sized macropores between carbon fibers and intrinsic nano scale mesopores (11.86 nm), which is conducive to remove antibiotics from water. Taking tetracycline (Tc) as an example, the maximum adsorption capacity and adsorption rate of AO-WPC for Tc are as high as 384.6 mg/g and 0.510 g/(mg‧min), respectively, which exhibits significant advantages over most of the recent absorbents, and the adsorption toward Tc reveals good resistance to various environmental factors, including pH, various ions, and dissolved organic matter (DOM). Moreover, good thermal stability enables the AO-WPC aerogel to be regenerated through simple burning, and the adsorption capacity of Tc only decreases by 10.4 % after 10 cycles. Mechanism research shows that hydrogen bonding and π-π electron-donor-acceptor (EDA) interaction play the important role in the adsorption. The excellent mechanical property and adsorption performance imply good practical prospect of the AO-WPC aerogel.

Feasibility of sludge deep dewaterability improvement for incineration disposal by combined conditioning of freeze-thaw and sawdust.

Sludge incineration is the main strategy for sludge reduction in China. The combined conditioning of lime and chemical agents has been proven to achieve sludge dewatering by disrupting the extracellular polymeric substances (EPS) of sludge and reducing its compressibility. However, when incineration is the intended disposal purpose, this method poses challenges such as incomplete combustion, equipment corrosion, secondary pollution, and decreased calorific value of sludge cake. In contrast, freeze-thaw conditioning, coupled with sawdust as a high-calorific-value bio-waste, emerges as an efficient and clean alternative. The research investigates the synergistic effects of freeze-thaw and sawdust co-conditioning on various sludge properties, including dewaterability, compressibility, consolidation, permeability, microscopicity, and calorific value. The study reveals that the combined conditioning significantly reduces water content and compressibility while increasing void ratio, consolidation, permeability, and enhancing the calorific value of the sludge cake. Specifically, sludge cake conditioned with 60% dried solids (DS) sawdust and freeze-thaw achieved a water content (Wc) of 49.07% and a calorific value of 1422.3 kcal/kg, meeting standards for self-sustained incineration. With heat recovery, the combined conditioning generates an economic revenue of 25.1 $/t DS after deducting costs, thereby reducing the overall cost of sludge reduction treatment. This research offers a clean and practical solution for sludge incineration and reduction, demonstrating great economic value and application potential.

Physical-property-based patterning: simply engineering complex tissues.

The field of biofabrication is rapidly expanding with the advent of new technologies and material systems to engineer complex tissues. In this opinion article, we introduce an emerging tissue patterning method, physical-property-based patterning, that has strong translational potential given its simplicity and limited dependence on external hardware. Physical-property-based patterning relies solely on the intrinsic density, magnetic susceptibility, or compressibility of an object, its surrounding solution, and the noncontact application of a remote field. We discuss how physical properties can be exploited to pattern objects and design a variety of biologic tissues. Finally, we pose several open questions that, if addressed, could transform the status quo of biofabrication, pushing us one step closer to patterning tissues in situ.

Fundamental drying and agglomeration experiments with bio-fraction and refuse derived fuel for the development of pyrolysis reactor feed.

The EU's circular economy concept necessitates increasing the recycling ratio of municipal solid wastes. There are many existing mechanical-biological processing plants in Hungary for the preparation of residual municipal solid wastes (RMSWs). The two most important products of these plants are the bio-fraction and the refuse derived fuel (RDF). Currently, there are problems with both of these material streams in Hungary, since most of the bio-fraction is still landfilled, and the local thermal utilisation of the RDF has not been implemented yet. The high moisture content of the produced bio-fraction and RDF causes difficulties for the downstream operations; therefore, there is recent engineering interest in drying and agglomeration of these materials. The authors have carried out systematic and parallel drying and briquetting experimental series to study the effect of the material, material composition, mass (volume or surface) of the material, particle size distribution and pre-treatment with a cutting mill on drying intensity in a 1 m3 oven and their effect on briquettability by a laboratory briquette press. The initial slope of the relative moisture loss as function of time was determined. Process engineering design methods of convective hot air-drying can be further developed taking into account the research results. Results can be used for the design of the feed of a pyrolysis reactor once reactor experiments have provided the optimal feed requirements.

Compaction and compressibility characteristics of snail shell ash and granulated blast furnace slag stabilized local bentonite for baseliner of landfill.

This study comprehensively explores the compaction and compressibility characteristics of snail shell ash (SSA) and ground-granulated blast-furnace slag (GBFS) in stabilizing local bentonite for landfill baseliner applications. The untreated soil, with a liquid limit of 65%, plastic limit of 35%, and plasticity index of 30%, exhibited optimal compaction at a moisture content of 32% and a maximum dry density of 1423 kg/m3. SSA revealed a dominant presence of 91.551 wt% CaO, while GBFS contained substantial 53.023 wt% SiO2. Treated samples with 20% GBFS and 5% SSA exhibited the highest maximum dry density (1561 kg/m3) and optimal moisture content (13%), surpassing other mixtures. The 15% SSA-treated sample demonstrated superior strength enhancement, reaching an unconfined compressive strength of 272.61 kPa over 28 days, while the 10% GBFS-treated sample achieved 229.95 kPa. The combination of 15% SSA exhibited the highest shear strength (49 kPa) and elastic modulus (142 MPa), showcasing robust mechanical properties. Additionally, the 15% SSA sample displayed favourable hydraulic conductivity (5.57 × 10-8 cm/s), outperforming other mixtures. Notably, the permeability test, a critical aspect of the study, was meticulously conducted in triplicate, ensuring the reliability and reproducibility of the reported hydraulic conductivity values. Treated samples with SSA and GBFS showed reduced compressibility compared to the control soil, with the 15% SSA-treated sample exhibiting a more consistent response to applied pressures. Scanning Electron Microscopy analysis revealed substantial composition changes in the 15% SSA mixture, suggesting its potential as an effective base liner in landfill systems. In conclusion, the 15% SSA sample demonstrated superior mechanical properties and hydraulic conductivity, presenting a promising choice for landfill liner applications.

Building-Envelope-Inspired, Thermomechanically Robust All-Fiber Ceramic Meta-Aerogel for Temperature-Controlled Dominant Infrared Camouflage.

The unsatisfactory properties of ceramic aerogels when subjected to thermal shock, such as strength degradation and structural collapse, render them unsuitable for use at large thermal gradients or prolonged exposure to extreme temperatures. Here, a building-envelope-inspired design for fabricating a thermomechanically robust all-fiber ceramic meta-aerogel with interlocked fibrous interfaces and an interwoven cellular structure in the orthogonal directions is presented, which is achieved through a two-stage physical and chemical process. Inspired by the reinforced concrete building envelope, a solid foundation composed of fibrous frames is constructed and enhanced through supramolecular in situ self-assembly to achieve high compressibility, retaining over 90% of maximum stress under a considerable compressive strain of 50% for 10 000 cycles, and showing temperature-invariance when compressed at 60% strain within the range of -100 to 500 °C. As a result of its distinct response to oscillation tolerance coupled with elastic recovery, the all-fiber ceramic meta-aerogel exhibits exceptional suitability for thermal shock resistance and infrared camouflage performance in cold (-196 °C) and hot (1300 °C) fields. This study provides an opportunity for developing ceramic aerogels for effective thermal management under extreme conditions.

Swelling of Ti3 C2 Tx MXene in Water and Methanol at Extreme Pressure Conditions.

Pressure-induced swelling has been reported earlier for several hydrophilic layered materials. MXene Ti3C2Tx is also a hydrophilic layered material composed by 2D sheets but so far pressure-induced swelling is reported for this material only under conditions of shear stress at MPa pressures. Here, high-pressure experiments are performed with MXenes prepared by two methods known to provide "clay-like" materials. MXene synthesized by etching MAX phase with HCl+LiF demonstrates the effect of pressure-induced swelling at 0.2 GPa with the insertion of additional water layer. The transition is incomplete with two swollen phases (ambient with d(001) = 16.7Å and pressure-induced with d(001) = 19.2Å at 0.2 GPa) co-existing up to the pressure point of water solidification. Therefore, the swelling transition corresponds to change from two-layer water intercalation (2L-phase) to a never previously observed three-layer water intercalation (3L-phase) of MXene. Experiments with MXene prepared by LiCl+HF etching have not revealed pressure-induced swelling in liquid water. Both MXenes also show no anomalous compressibility in liquid methanol. The presence of pressure-induced swelling only in one of the MXenes indicates that the HCl+LiF synthesis method is likely to result in higher abundance of hydrophilic functional groups terminating 2D titanium carbide.

Realizing Persistent Zero Area Compressibility over a Wide Pressure Range in Cu2 GeO4 by Microscopic Orthogonal-Braiding Strategy.

Zero area compressibility (ZAC) is an extremely rare mechanical response that exhibits an invariant two-dimensional size under hydrostatic pressure. All known ZAC materials are constructed from units in two dimensions as a whole. Here, we propose another strategy to obtain the ZAC by microscopically orthogonal-braiding one-dimensional zero compressibility strips. Accordingly, ZAC is identified in a copper-based compound with a planar [CuO4 ] unit, Cu2 GeO4 , that possesses an area compressibility as low as 1.58(26) TPa-1 over a wide pressure range from ≈0 GPa to 21.22 GPa. Based on our structural analysis, the subtle counterbalance between the shrinkage of [CuO4 ] and the expansion effect from the increase in the [CuO4 ]-[CuO4 ] dihedral angle attributes to the ZAC response. High-pressure Raman spectroscopy, in combination with first-principles calculations, shows that the electron transfer from in-plane bonding dx 2 -y 2 to out-of-plane nonbonding dz 2 orbitals within copper atoms causes the counterintuitive extension of the [CuO4 ]-[CuO4 ] dihedral angle under pressure. Our study provides an understanding on the pressure-induced structural evolution of copper-based oxides at an electronic level and facilitates a new avenue for the exploration of high-dimensional anomalous mechanical materials.

Way to a Library of Ti-Series Oxide Nanofiber Sponges that are Highly Stretchable, Compressible, and Bendable.

Ti-series oxide ceramics in the form of aerogels, such as TiO2, SrTiO3, BaTiO3, and CaCu3Ti4O12, hold tremendous potential as functional materials owing to their excellent optical, dielectric, and catalytic properties. Unfortunately, these inorganic aerogels are usually brittle and prone to pulverization owing to weak inter-particulate interactions, resulting in restricted application performance and serious health risks. Herein, a novel strategy is reported to synthesize an elastic form of an aerogel-like, highly porous structure, in which activity-switchable Ti-series oxide sols transform from the metastable state to the active state during electrospinning, resulting in condensation and solidification at the whipping stage to obtain curled nanofibers. These curled nanofibers are further entangled when flying in the air to form a physically interlocked, elastic network mimicking the microstructure of high-elasticity hydrogels. This strategy provides a library of Ti-series oxide nanofiber sponges with unprecedented stretchability, compressibility, and bendability, possessing extensive opportunities for greener, safer, and broader applications as integrated or wearable functional devices. As a proof-of-concept demonstration, a new, elastic form of TiO2, composed of both "white" and "black" TiO2 nanofiber sponges, is constructed as spontaneous air-conditioning textiles in smart clothing, buildings, and vehicles, with unique bidirectional regulation of radiative cooling in summer and solar heating in winter.

Preparation of Thin Films Containing Modified Hydroxyapatite Particles and Phospholipids (DPPC) for Improved Properties of Biomaterials.

The main aims of thin biofilm synthesis are to either achieve a new form to promote the transport of drugs in oral delivery systems or as a coating to improve the biocompatibility of the implant's surface. In this study, the Langmuir monolayer technique was employed to obtain films containing Mg-doped hydroxyapatite with 0.5%, 1.0%, and 1.5% Mg(II). The obtained modified HA particles were analysed via the FT-IR, XRD, DLS, and SEM methods. It was shown that the modified hydroxyapatite particles were able to form thin films at the air/water interface. BAM microscopy was employed to characterized the morphology of these films. In the next step, the mixed films were prepared using phospholipid (DPPC) molecules and modified hydroxyapatite particles (HA-Mg(II)). We expected that the presence of phospholipids (DPPC) in thin films improved the biocompatibility of the preparing films, while adding HA-Mg(II) particles will promote antibacterial properties and enhance osteogenesis processes. The films were prepared in two ways: (1) by mixing DPPC and HA-Mg (II) and spreading this solution onto the subphase, or (2) by forming DPPC films, dropping the HA-Mg (II) dispersion onto the phospholipid monolayer. Based on the obtained π-A isotherms, the surface parameters of the achieved thin films were estimated. It was observed that the HA-Mg(II) films can be stabilized with phospholipid molecules, and a more stable structure was obtained from films synthesied via method (2).

Active Contraction in the Stable Mechanical Environment of the Tunic of the Ascidian, Halocynthia roretzi, a Polysaccharide-Based Tissue with Blood Circulatory System.

Halocynthia roretzi, a member of Ascidiacea, is covered with its own tunic, which is composed of polysaccharides, such as cellulose Iß and sulfated chitin. H. roretzi has an open-vessel system, whose blood vessels and hemocytes are found in the tunic, so that the mechanical environment of the tunic could be carefully controlled because of its influence on hemocyte behaviors. While active deformation of the tunic and related phenomena have been previously reported, the mechanical environment in the tunic, which directly influences its deformation, has been rarely investigated. Meanwhile, the developments of actuators based on cellulose and chitin have been frequently reported. However, a cellulose-sulfated chitin actuator has not been proposed. In this study, the mechanical environment of the tunic, which has been rarely investigated despite its importance in the active deformation of the tunic, was evaluated using finite element analysis. A finite element model of the tunic, based on its histological characteristics as well as deformation patterns, was developed. The results showed that the shape of the tunic, the pattern of fiber distribution, and control of the water content influenced the mechanical environment.

Mechanical imbalance between normal and cancer cells drives epithelial defense against cancer.

Cell competition enables normal wildtype cells of epithelial tissue to eliminate mutant cells expressing activated oncoproteins such as HRasV12. However, the driving force behind this fundamental epithelial defense against cancer remains enigmatic. Here, we employ tissue stress microscopy and theoretical modeling and invent a new collective compressibility measurement technique called gel compression microscopy to unveil the mechanism governing cell competition. Stress microscopy reveals unique compressive stress experienced by the mutant cells, contrasting with predominantly tensile stress experienced by normal cells. A cell-based computer simulation then predicts that this compressive stress arises out of a mechanical imbalance between two competing populations due to a difference in their collective compressibility and rigidity. Gel compression microscopy empirically confirms the prediction and elucidates a three-fold higher compressibility of the mutant population than the normal population. Mechanistically, this difference stems from the reduced abundance and coupling of junctional E-cadherin molecules in the mutant cells, which weakens cell-cell adhesions and renders the mutant population more compressible. Taken together, our study elucidates both the physical principle and the underlying molecular mechanism driving cell competition in epithelial defense against cancer and opens new directions for mechanomedicine in cancer.

Investigations on Compaction Behavior of Kollidon®SR-Based Multi-component Directly Compressed Tablets for Preparation of Controlled Release Diclofenac Sodium.

The physics of tablets mixtures has gained much attention lately. The purpose of this work is to evaluate the compaction properties of Kollidon® SR (KSR) in the presence of different excipients such as Microcrystalline cellulose (MCC), Monohydrous lactose (MH Lactose), Poly (vinyl acetate) (PVA100), and a water-soluble drug Diclofenac sodium (DNa) to prepare once daily formulation. Tablets were prepared using direct compression and were compressed into flat-faced tablets using hydraulic press at various pressures. The combination of MCC and KSR in the tablets showed reduced porosity, and almost constant low Py values as KSR levels increased; also, KSR-DNa tablets had higher percentage porosity and crushing strength values than KSR-MH Lactose tablets. The crushing strengths of KSR-MCC tablets were larger than those of KSR-DNa tablets. Ternary mixture tablets comprised of KSR-MCC-DNa showed decreased porosities and low Py values as the percentage of KSR increased especially at high compression pressures but had higher crushing strengths compared to KSR-DNa or MCC-DNa binary tablets. KSR-MH Lactose-DNa ternary tablets experienced lower porosities and crushing strengths compared to KSR-MCC-DNa tablets. Quaternary tablets of KSR-PVA100-MCC-DNa showed lower porosity and Py values than quaternary tablets obtained using similar proportion of MH Lactose instead of MCC. In conclusion, optimum quaternary tablets were obtained with optimum crushing strengths, relatively low Py, and moderate percentage porosities among all prepared quaternary tablets. The drug release of the optimum quaternary tablets demonstrated similar in vitro release profile compared to that of the marketed product with a mechanism of release that follows Korsmeyer-Peppas model.

Effect of Crystallite Size on the Flexibility and Negative Compressibility of Hydrophobic Metal-Organic Frameworks.

Flexible nanoporous materials are of great interest for applications in many fields such as sensors, catalysis, material separation, and energy storage. Of these, metal-organic frameworks (MOFs) are the most explored thus far. However, tuning their flexibility for a particular application remains challenging. In this work, we explore the effect of the exogenous property of crystallite size on the flexibility of the ZIF-8 MOF. By subjecting hydrophobic ZIF-8 to hydrostatic compression with water, the flexibility of its empty framework and the giant negative compressibility it experiences during water intrusion were recorded via in operando synchrotron irradiation. It was observed that as the crystallite size is reduced to the nanoscale, both flexibility and the negative compressibility of the framework are reduced by ∼25% and ∼15%, respectively. These results pave the way for exogenous tuning of flexibility in MOFs without altering their chemistries.

Investigating the Impact of Co-processed Excipients on the Formulation of Bromhexine Hydrochloride Orally Disintegrating Tablets (ODTs).

PURPOSE: Orodispersible tablets (orally disintegrating tablets, ODTs) have been used in pharmacotherapy for over 20 years since they overcome the problems with swallowing solid dosage forms. The successful formula manufactured by direct compression shall ensure acceptable mechanical strength and short disintegration time. Our research aimed to develop ODTs containing bromhexine hydrochloride suitable for registration in accordance with EMA requirements. METHODS: We examined the performance of five multifunctional co-processed excipients, i.e., F-Melt® C, F-Melt® M, Ludiflash®, Pharmaburst® 500 and Prosolv® ODT G2 as well as self-prepared physical blend of directly compressible excipients. We tested powder flow, true density, compaction characteristics and tableting speed sensitivity. RESULTS: The manufacturability studies confirmed that all the co-processed excipients are very effective as the ODT formula constituents. We noticed superior properties of both F-Melt's®, expressed by good mechanical strength of tablets and short disintegration time. Ludiflash® showed excellent performance due to low works of plastic deformation, elastic recovery and ejection. However, the tablets released less than 30% of the drug. Also, the self-prepared blend of excipients was found sufficient for ODT application and successfully transferred to production scale. Outcome of the scale-up trial revealed that the tablets complied with compendial requirements for orodispersible tablets. CONCLUSIONS: We proved that the active ingredient cannot be absorbed in oral cavity and its dissolution profiles in media representing upper part of gastrointestinal tract are similar to marketed immediate release drug product. In our opinion, the developed formula is suitable for registration within the well-established use procedure without necessity of bioequivalence testing.

Nanomechanical properties of SSTSAA microcrystals are dominated by the inter-sheet packing.

Amyloid fibrils have been associated with human disease for many decades, but it has also become apparent that they play a functional, non-disease-related role in e.g. bacteria and mammals. Moreover, they have been shown to possess interesting mechanical properties that can be harnessed for future man-made applications. Here, the mechanical behaviour of SSTSAA microcrystals has been investigated. The SSTSAA peptide organization in these microcrystals has been related to that in the corresponding amyloid fibrils. Using high-pressure X-ray diffraction experiments, the bulk modulus K, which is the reciprocal of the compressibility ß, has been calculated to be 2.48 GPa. This indicates that the fibrils are tightly packed, although the packing of most native globular proteins is even better. It is shown that the value of the bulk modulus is mainly determined by the compression along the c-axis, that relates to the inter-sheet distance in the fibrils. These findings corroborate earlier data obtained by AFM and molecular dynamics simulations that showed that mechanical resistance varies according to the direction of the applied strain, which can be related to packing and hydrogen bond contributions. Pressure experiments provide complementary information to these techniques and help to acquire a full mechanical characterization of biomolecular assemblies. This article is part of the theme issue 'Exploring the length scales, timescales and chemistry of challenging materials (Part 2)'.

Extraction of Polyphenols from Slovenian Hop (Humulus lupulus L.) Aurora Variety Using Deep Eutectic Solvents: Choice of the Extraction Method vs. Structure of the Solvent.

Polyphenols from Slovenian hops (Humulus lupulus L.) of the Aurora variety were extracted by different methods and using classical solvents and several deep eutectic solvents (DES) based on choline chloride as the hydrogen bond acceptor component. The obtained extract solutions were analyzed by HPLC for the content of extracted α- and ß-acids and extracted xanthohumol. It was found that choline chloride:phenol DES concentrated aqueous solution had an extraction efficiency close to that of diethyl ether, which is considered one of the best classical extraction solvents for polyphenols from hops. The comparison of the extraction efficiency with other choline chloride-based DESs showed that the chemical similarity of the phenol ring in the solvent DES with the polyphenols in hops may be crucial for a highly efficient extraction with choline chloride:phenol DES. On the other hand, the choice of extraction method and the viscosity of the solvents tested seem to play only a minor role in this respect. As far as we know, this is the first study to attempt to relate extraction efficiency in the extraction of hydrophobic solutes to the compressibility of the DES extractants, the latter of which may be correlated with the extent of hydrophobic hydration around the DES components. In addition, using the heating and stirring method for the preparation of choline chloride-based DES concentrated aqueous solutions we found no support for the occurrence of water in two different roles (in the structural and in the dilution role) in these solvents.