[Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching].

OBJECTIVE: To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention. METHODS: By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s. RESULTS: At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm. CONCLUSION: When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

Managing Fibrous Maxillary Ridge: A Case Series of Impression Techniques.

Fibrous ridges on the edentulous maxillary arch are commonly found in combination syndrome or due to ill-fitting dentures. Often, these cases are managed conservatively using modified impression techniques to achieve better support and peripheral seal without displacing the movable tissue. Many impression techniques were proposed and justified with their respective ideologies, but some may complicate both the clinical and laboratory procedures. In this report, two simplified techniques are demonstrated to make an impression of the maxillary arch with fibrous ridges. Laboratory steps in custom tray fabrication are also emphasised for a successful and predictable impression.

Survival rates, patient satisfaction, and prosthetic complications of implant fixed complete dental prostheses: a 12-month prospective study.

PURPOSE: To determine the survival rate, incidence of prosthetic complications, and patient satisfaction of implant fixed complete dental prostheses (IFCDPs) after a mean observation period of 1.4 years. MATERIALS AND METHODS: Twenty-eight (28) eligible participants were recruited according to specific inclusion and exclusion criteria. The definitive metal-acrylic resin IFCDPs consisted of titanium bars veneered with acrylic resin and acrylic denture teeth. Prosthodontic complications, divided into major and minor, were monitored. Parameters such as gender, jaw location, bruxism, and occlusal scheme were evaluated. Moreover, a questionnaire was administered throughout the study to assess patient satisfaction. Poisson regression as well as repeated measures ANOVA were used for statistical analysis. RESULTS: Fourteen (14) males and 14 females were enrolled and followed-up at 3, 6, and 12 months. All IFCDPs survived (100% survival rate). The most frequent minor complication was the loss of material used to close the screw access hole (20% out of total complications). The most frequent major complication was chipping of the acrylic denture teeth (77.14% out of total complications). Gender (p = 0.008) and bruxism (p = 0.030) were significant predictors for the total major complications (major wear and major chipping) while occlusal scheme was a significant predictor for major chipping events (p = 0.030). CONCLUSIONS: While IFCDPs demonstrated high prosthetic survival rates, they also exhibited a high number of chipping events of the acrylic veneering material, especially in males, bruxers, and individuals with canine guidance occlusion. However, the occurrence of these prosthetic complications did not negatively affect patient satisfaction.

Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching / 北京大学学报(医学版)

OBJECTIVE@#To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention.@*METHODS@#By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s.@*RESULTS@#At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm.@*CONCLUSION@#When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

Prótese overdenture: sistema o'ring / Overdenture prosthesis: o'ring system

Overdenture é uma prótese total que se caracteriza por usar apoios retentivos para que aumente sua estabilidade e retenção na cavidade bucal, gerando assim menor desconforto ao paciente e melhor adaptação. A Prótese overdenture dentossuportada necessita de elementos dentais remanescentes com canais tratados endodonticamente e que possuam suporte periodontal adequado. O objetivo deste relato de caso clínico é expor a sequência de confecção de uma prótese overdenture dentossuportada maxilar associada a uma prótese total convencional mandibular, com os passos clínicos detalhados por meio de uma abordagem teórica e visual. Esse tipo de reabilitação favorece a adaptação do paciente à nova condição, visto que o uso de próteses totais convencionais pode causar certo desconforto ao paciente devido à falta de retenção e estabilidade. Essa manutenção dos dentes remanescentes favorece à manutenção óssea e a futura decisão do paciente em optar pela instalação de implantes dentários, podendo confeccionar próteses implantorretidas (overdentures) ou implantossuportadas (protocolo).O Paciente demonstrou-se satisfeito com o resultado estético e funcional após a instalação da prótese concretizando que o tratamento é viável(AU)

Overdenture is a denture that utilizing retentive supports for increase stability and retention in oral cavity. The tooth-supported overdenture require dental elements with root canal therapy and good periodontal support. The aim of this study is to report the confection of a maxillary tooth-supported overdenture associated with mandibular denture and your clinical steps. This rehabilitation promotes the patient's adaptation the new condition, since the use of conventional dentures may cause discomfort due to lack of retention and stability. The preservation of dental elements promotes bone maintenance and forthcoming decision of the patient in the installation of dental implants that can choose implantretained or implant-supported prosthesis. Patient was satisfied with aesthetic and functional result after installation of prosthesis(AU)

The Effect of Number and Distribution of Mini Dental Implants on Overdenture Stability: An In Vitro Study.

The rotational movement of mini dental implants (MDIs) overdenture disturbs the function of the prosthesis. Many dentists place more MDIs to improve the overdenture stability; however, the influence of the MDIs number and distribution on the overdenture resistance to para-axial dislodgment has not been investigated. Seven resin models simulating atrophic mandibles housed twenty MDIs placed according to seven arrangements. Acrylic overdentures were fabricated for each cast and were dislodged five times in lateral, anterior and posterior directions, and the peak load dislodgment was measured. Each overdenture underwent 540 axial removal/placement cycles. The para-axial dislodgments were measured again, and data were compared. Dislodgment force values were measured in all directions, and the data were analysed using analysis of variance ANOVA and post hoc (p < 0.05). After six months of simulated placement/removal, increasing the MDI number showed a difference in resistance to para-axial dislodgment. The distribution affected the resistance to dislodgment in some directions. The inter-implant distance of 27 mm provided better resistance to posterior dislodgment than placing two MDIs close together at 19 mm. The placement of three MDIs at any distribution showed no significant difference except for resistance to posterior dislodgment. FourMDIs placed at any distribution showed a significant difference in all groups in all tested directions. The resistance to the para-axial dislodgment of MDI overdenture could improve with the increasing MDIs number and careful planning of MDI distribution.

[Application evaluation of prefabricated rigid connecting bar in implants immediate impression preparation of edentulous jaw].

OBJECTIVE: To compare the operation complexity and accuracy of traditional splint impression technique and impression technique with prefabricated rigid connecting bar system for full-arch implants-supported fixed protheses in vitro. METHODS: Standard mandibular edentulous model with six implant analogs was prepared. The implants were placed at the bone level and multiunit abutments screwed into the implants. Two impression techniques were performed: the traditional splint impression technique was used in the control group, and the rigid connecting bar system was used in the test group. In the control group, impression copings were screwed into the multiunit abutments and connected with autopolymerizing acrylic resin. Open tray impression was fabricated with custom tray and polyether. In the test group, cylinders were screwed into the multiunit abutments. Prefabricated rigid bars with suitable length were selected and connected to the cylinders with small amount of autopolymerizing acrylic resin, and open tray impression was obtained. Impression procedures were repeated 6 times in each group. The working time of the two impression methods were recorded and compared. Analogs were screws into the impressions and gypsum casts were poured. The gypsum casts and the standard model were transferred to stereolithography (STL) files with model scanner. Comparative analysis of the STL files of the gypsum casts and the standard model was carried out and the root mean square (RMS) error value of the gypsum casts of the control and test groups compared with the standard model was recorded. The trueness of the two impression techniques was compared. RESULTS: The work time in the test group was significantly lower than that in the control group and the difference was statistically significant [(984.5±63.3) s vs. (1 478.3±156.2) s, P < 0.05]. Compared with the standard model, the RMS error value of the implant abutments in the test group was (16.9±5.5) µm. The RMS value in the control group was (20.2±8.0) µm. The difference between the two groups was not significant (P>0.05). CONCLUSION: The prefabricated rigid connecting bar can save the chair-side work time in implants immediate loading of edentulous jaw and simplify the impression process. The impression accuracy is not significantly different from the traditional impression technology. The impression technique with prefabricated rigid connecting bar system is worthy of clinical application.

Comparison of retention and fracture load of endocrowns made from zirconia and zirconium lithium silicate after aging: an in vitro study.

BACKGROUND: This study aimed to compare retention and fracture load in endocrowns made from translucent zirconia and zirconium lithium silicate. METHODS: Fifty-six intact human maxillary molars after being mounted in acrylic resin, were scanned to acquire biogeneric copies. Specimens underwent standard endodontic treatment and were prepared for endocrown up to 2 mm above the cementoenamel junction. The specimens were randomly divided into two groups of 28, and endocrowns were designed using biogeneric copies and milled from high-translucent zirconia disks (Zr) and zirconium lithium silicate blocks (ZLS). After cementation with dual-cure resin cement, all the specimens underwent thermomechanical aging, and pull-out retention test and compressive test were conducted (14 specimens were used for each test in each group, n = 14), and failure modes in both tests were evaluated. RESULTS: Independent samples t-test showed significant difference between the retention of Zr (271.5 N ± 114.31) and ZLS (654.67 N ± 223.17) groups (p value = 0.012). Compressive test results were also significantly different between Zr (7395.07 N ± 1947.42) and ZLS (1618.3 N ± 585) (p = 0.002). Failure mode of retention test was primarily adhesive failure at the cement-restoration interface in Zr group and cement-tooth interface in ZLS group. Failure modes of fracture test for Zr group were 7 non-restorable fractures and one restorable fracture while 6 specimens resisted compressive loads up to 8500 N without fracture. ZLS group showed 7 restorable and 7 non-restorable failures. CONCLUSIONS: Zr endocrowns showed significantly lower retention and higher fracture strength. Both materials seem to be suitable for fabrication of endocrown in clinical setup.

Dental treatment under intravenous sedation prolongs longevity of a fixed prosthesis in patients with intellectual disabilities.

AIMS: This study aimed to assess the longevity of a fixed prosthesis in patients with intellectual disability (ID) and to investigate the risk factors associated with the failure of a prosthesis due to abutment tooth extraction or prosthesis dislodgement or removal. METHODS: We studied past medical records to evaluate the longevity of 315 prostheses that were luted in 76 patients with ID. We calculated the survival rates and assessed 15 variables potentially associated with prosthetic failure using multivariate Cox regression analyses with shared frailty for patients. RESULTS: Three-quarters of our sample population had severe or profound ID. The maximum observation period was 31.0 years, and the corresponding survival ratio was 32.5%; the survival ratio at 10 years was 59.4%. The use of intravenous sedation significantly influenced the success of the prosthesis, with the hazard ratio (HR) being 0.49 times that of conventional treatment without behavior-altering drug therapy. The most significant risk factor for prosthetic failure was age at placement; the HR for patients aged ≥31 years was 2.82 times that for patients aged ≤ 20 years. CONCLUSIONS: In patients with severe ID, appropriate intravenous sedation was effective in prolonging the longevity of a fixed prosthesis.

Avaliação do tipo de retenção e o uso de diferentes intermediários na adaptação de próteses unitárias sobre implantes / Evaluation of the type of retention and the use of different abutments in the adaptation of single prostheses on implants

Atualmente, devido a perda do elemento dentário e a procura por um tratamento estético e principalmente funcional, a reabilitação com próteses sobre implante tem sido amplamente empregada, com elevada previsibilidade a longo prazo. Com isso, muito tem sido relatado na literatura acerca das possíveis complicações dessa modalidade de tratamento, principalmente relacionado às possibilidades de falhas mecânicas das próteses implantossuportadas. Por isso, o objetivo do presente projeto foi avaliar a influência na adaptação marginal e interna, da utilização do intermediário protético e do tipo de retenção das próteses (parafusada e cimentada) em implantes cone morse submetidos à ciclagem mecânica. Foram confeccionados 40 corpos de prova, no qual cada um tinha a presença de um implante, com as dimensões de 4mm de diâmetro e 11,5mm de comprimento cone morse (n = 40). Dessa forma, foi avaliado a influência da utilização do intermediário e dos sistemas de retenção em cada conexão de maneira específica. Metade dos corpos de prova de cada sistema de conexão foram confeccionados em UCLA (n=20, sendo 10 parafusadas e 10 cimentadas), enquanto que a outra metade foi utilizado um intermediário pré-fabricado (Pilar Universal (n=20, sendo 10 parafusadas e 10 cimentadas). Os corpos de prova foram submetidos à ciclagem mecânica submersos em água destilada simulando um tempo clínico de cinco anos. Além disso, foram avaliados quanto ao torque e destorque (N) e adaptação marginal e interna (µm) antes e após a ciclagem mecânica. Os dados provenientes das mensurações foram organizados em tabela em formato Excel (Microsoft Office Excel, Redmond, WA, Estados Unidos) e submetidos ao software SigmaPlot (SigmaPlot, San Jose, CA, EUA) versão 12.0. Todos os dados foram analisados inicialmente com a utilização da estatística descritiva. Em seguida, os dados para intrusão (valores positivos), extrusão (valores negativos), destorque inicial, destorque final, e descimentação foram analisados em relação a distribuição de normalidade (teste Shapiro-Wilk e igualdade de variância) e, posteriormente, foi adotada a Análise de Variância (ANOVA) a um fator (Grupos diferentes materiais: G1 a G4), quando houve normalidade dos dados, o pós teste de Tukey foi adotado para as comparações múltiplas, quando não foi identificado uma distribuição normal, empregou-se o teste de Kruskall-Wallis e pós-teste de Dunn's ou Tukey, semelhantemente foi realizada a análise específica das variáveis pilares (UCLA e Pilar Universal) e sistemas de retenção (Parafusado e Cimentado). Para todos os testes aplicou-se nível de significância de 5% (α=0,05). A análise gráfica foi considerada através de um gráfico de barras para os dados que apresentaram normalidade com valores de média e desvio padrão, e as demais análises que não apresentaram normalidade foi considerado a confecção de um boxplot para cada grupo comparativo. As próteses sobre implante utilizando pilares em zircônia tem ganhado cada vez mais espaço, além do estudo in vitro, foi realizada uma revisão sistemática para comparar a perda óssea marginal e as complicações próteticas de reabilitações utilizando pilares de zircônia cimentado e parafusado. Em relação as próteses cimentadas e parafusadas, devido as evidências conflitantes e a presença de muitas revisões sistemáticas sobre o tema, foi realizada uma overview de revisões sistemáticas, com o objetivo de compilar as informações disponiveis e avaliar a qualidade metodologica desses estudos a respeito das complicações presentes nas próteses sobre implante cimentadas ou parafusadas(AU)

Currently, due to the loss of the dental element and the search for an aesthetic and mainly functional treatment, rehabilitation with implant prostheses has been widely used, with high long-term predictability. Thus, much has been reported in the literature about the possible complications of this treatment modality, mainly related to the possibility of mechanical failure of implant-supported prostheses. Therefore, the objective of the present project was to evaluate the influence on the marginal and internal adaptation, the use of the prosthetic intermediate and the type of retention of the prostheses (screwed and cemented) in morse taper implants submitted to mechanical cycling. 40 specimens were made, in which each one had an implant, with dimensions of 4 mm in diameter and 11.5 mm in length (n = 40). In this way, the influence of the use of intermediaries and retention systems in each connection was evaluated in a specific way. Half of the specimens of each connection system were made in UCLA (n=20, being 10 screwed and 10 cemented), while the other half was used a prefabricated intermediate (Universal Abutment (n=20, being 10 screwed) and 10 cemented). The specimens were submitted to mechanical cycling submerged in distilled water simulating a clinical time of five years. In addition, they were evaluated for torque and detorque (N) and marginal and internal adaptation (µm) before and after mechanical cycling. Data from measurements were organized in a table in Excel format (Microsoft Office Excel, Redmond, WA, USA) and submitted to SigmaPlot software (SigmaPlot, San Jose, CA, USA) version 12.0. All data were initially analyzed using descriptive statistics. Then, data for intrusion (positive values), extrusion (negative values), initial detorque, final detorque, and debonding were analyzed in relation to dist determination of normality (Shapiro-Wilk test and equality of variance) and, later, the one-way Analysis of Variance (ANOVA) was adopted (Different material groups: G1 to G4), when there was normality of the data, the Tukey post test was adopted for multiple comparisons, when a normal distribution was not identified, the Kruskall-Wallis test and Dunn's or Tukey post-test were used, similarly the specific analysis of the pillar variables (UCLA and Universal Pillar) and systems retainer (Screwed and Cemented). For all tests, a significance level of 5% (α=0.05) was applied. The graphical analysis was considered through a bar graph for the data that presented normality with mean and standard deviation values, and the other analyzes that did not present normality was considered the creation of a boxplot for each comparative group. Implant prostheses using zirconia abutments have gained more and more space, in addition to the in vitro study, a systematic review was performed to compare marginal bone loss and prosthetic complications of rehabilitations using cemented and screwed zirconia abutments. Regarding cemented and screw-retained prostheses, due to conflicting evidence and the presence of many systematic reviews on the subject, an overview of systematic reviews was performed, with the objective of compiling the available information and evaluating the methodological quality of these studies regarding complications present in cemented or screw-retained implant prostheses(AU)

Application evaluation of prefabricated rigid connecting bar in implants immediate impression preparation of edentulous jaw / 北京大学学报(医学版)

OBJECTIVE@#To compare the operation complexity and accuracy of traditional splint impression technique and impression technique with prefabricated rigid connecting bar system for full-arch implants-supported fixed protheses in vitro.@*METHODS@#Standard mandibular edentulous model with six implant analogs was prepared. The implants were placed at the bone level and multiunit abutments screwed into the implants. Two impression techniques were performed: the traditional splint impression technique was used in the control group, and the rigid connecting bar system was used in the test group. In the control group, impression copings were screwed into the multiunit abutments and connected with autopolymerizing acrylic resin. Open tray impression was fabricated with custom tray and polyether. In the test group, cylinders were screwed into the multiunit abutments. Prefabricated rigid bars with suitable length were selected and connected to the cylinders with small amount of autopolymerizing acrylic resin, and open tray impression was obtained. Impression procedures were repeated 6 times in each group. The working time of the two impression methods were recorded and compared. Analogs were screws into the impressions and gypsum casts were poured. The gypsum casts and the standard model were transferred to stereolithography (STL) files with model scanner. Comparative analysis of the STL files of the gypsum casts and the standard model was carried out and the root mean square (RMS) error value of the gypsum casts of the control and test groups compared with the standard model was recorded. The trueness of the two impression techniques was compared.@*RESULTS@#The work time in the test group was significantly lower than that in the control group and the difference was statistically significant [(984.5±63.3) s vs. (1 478.3±156.2) s, P < 0.05]. Compared with the standard model, the RMS error value of the implant abutments in the test group was (16.9±5.5) μm. The RMS value in the control group was (20.2±8.0) μm. The difference between the two groups was not significant (P>0.05).@*CONCLUSION@#The prefabricated rigid connecting bar can save the chair-side work time in implants immediate loading of edentulous jaw and simplify the impression process. The impression accuracy is not significantly different from the traditional impression technology. The impression technique with prefabricated rigid connecting bar system is worthy of clinical application.

Retention Assessment of High Performance Poly-etheretherketone Removable Partial Denture Frameworks Constructed by Various Techniques (in vitro Study).

STATEMENT OF THE PROBLEM: Poly-etheretherketone is a novel material used in the construction of the removable partial dentures frameworks instead of the metal frameworks. This material can be fabricated by various techniques. Most common methods are the injection molding or Computer Aided Design/Computer Aiding Manufacturing (CAD/CAM) milling techniques. The fabrication technique may affect the adaptation of the frameworks by influencing the retention. PURPOSE: To assess the effect of the processing techniques of high performance Poly-etheretherketone either by injection molding (pressing) or CAD/CAM milling techniques on removable partial denture frameworks retention for rehabilitation of upper class I Kennedy classification. MATERIALS AND METHOD: This in vitro study was performed on one epoxy resin model representing the partially edentulous maxillary arch with natural teeth extending from first premolar to first premolar. First premolars and canines were reduced to receive porcelain fused to metal crowns with 0.50mm mesio-buccal retentive undercuts, distal guiding planes and mesial occlusal rest seat on first premolars and cingulum rest seat on canines. Considering the construction technique of frameworks, twenty samples were divided into two groups. In the group I, ten frameworks were fabricated by injection molding, and in the group II, ten frameworks were fabricated by CAD/CAM. The removal and insertion was carried out at 120, 720 and 1440 cycles for both groups, respectively. The retention values were measured by using Universal Testing Machine before cycling and after each interval. RESULTS: Independent t-test showed significant difference on retention at different simulation cycles between groups. Group II exhibited significantly less retention than group I (p< 0.001), while comparing the retention at different cycles within each group by paired sample t-test exhibited significant decrease of retention till the end of the cycling (p< 0.001). CONCLUSION: From the retention point of view, high performance poly-etheretherketone frameworks fabricated by injection molding technique provided a promising method over CAD/CAM technique milling method.

Tasa de supervivencia de prótesis fija unitaria de cerámica feldespática y feldespática reforzada / Survival rate of feldspathic and reinforced feldspathic ceramic single-unit fixed prostheses

Introducción: Gracias a su eficiencia y al uso exclusivo de cerámicas libres de metal, en rehabilitación oral se ha logrado alcanzar los estándares estéticos y mecánicos, manteniendo o, incluso, superando, la calidad de los tratamientos en comparación con las restauraciones metal cerámicas tradicionales. Actualmente los mecanismos de confeccion de cerámica libre están evolucionando cada vez mas hacia las tecnologías maquinadas CAD-CAM y disminuyendo su producción mediante la técnica de Inyeccion PRESS. Objetivo: Comparar la tasa de supervivencia de prótesis fija unitaria realizadas con cerámicas feldespáticas convencionales y reforzadas con disilicato de litio, confeccionadas con sistema CAD/CAM de CEREC® chair-side, en comparación con el método de inyección de laboratorio PRESS convencional de prensión. Métodos: Revisión sistemática realizada a través de búsqueda de evidencia científica en PubMed, PubMed Clinical Queries, Epistemónikos, Tripdatabase, Cochrane Library, recursos electrónicos de la Universidad de los Andes y bibliografía retrógrada, de artículos publicados hasta el año 2019. Se incluyeron todos aquellos estudios referentes a prótesis fija unitaria de cerámicas feldespática convencional y feldespática reforzada con disilicato de litio, confeccionadas mediante CAD/CAM y/o método convencional. Resultados: Un total de 28 artículos cumplieron los criterios de inclusión: 21 estudios observacionales de cohorte, 4 ensayos clínicos aleatorizados y 3 no aleatorizados. A corto y mediano plazo, CAD/CAM de CEREC® registró tasas de supervivencia de 98 por ciento y 91,9 por ciento, respectivamente. El sistema convencional registró tasas de supervivencia de 97,5 por ciento a corto plazo y 93 por ciento a mediano. Conclusiones: A corto plazo se describe en la literatura que CAD/CAM de CEREC® tuvo una tasa de supervivencia ligeramente superior al sistema convencional. Por otro lado, a mediano plazo CAD/CAM de CEREC® presentó una leve disminución respecto al sistema convencional. Aún no hay estudios disponibles para determinar la supervivencia clínica de los tratamientos a largo plazo(AU)

Introduction: Thanks to its efficiency and the exclusive use of metal-free ceramics, in oral rehabilitation it has been possible to achieve aesthetic and mechanical standards, maintaining or even exceeding the quality of the treatments compared to traditional metal-ceramic restorations. Currently, free ceramic manufacturing mechanisms are increasingly evolving towards CAD-CAM machined technologies and decreasing their conventional production through the PRESS Injection technique. Objective: Compare the survival rate of single-unit fixed prostheses made with conventional feldspathic ceramics and reinforced with lithium disilicate by the CEREC® CAD/CAM chairside system, with the conventional PRESS laboratory injection method. Methods: A systematic review was conducted of scientific evidence included in papers published until the year 2019 in PubMed, PubMed Clinical Queries, Epistemonikos, Tripdatabase, Cochrane Library, electronic resources of Los Andes Peruvian University, and retrograde bibliography. The papers selected dealt with conventional and lithium-disilicate reinforced feldspathic ceramic single-unit prostheses made by CAD/CAM and/or the conventional method. Results: A total 28 papers met the inclusion criteria. Of these, 21 were observational cohort studies, four were randomized clinical assays and three were non-randomized assays. Short- and mid-term, CEREC® CAD/CAM achieved survival rates of 98 percent and 91.9 percent, respectively. The conventional system achieved survival rates of 97.5 percent short-term and 93 percent mid-term. Conclusions: As described in the literature, CEREC® CAD/CAM had a slightly higher survival rate than the conventional system in the short term. In the medium term, however, CEREC® CAD/CAM displayed a slight reduction in comparison with the conventional system. No studies are available to determine the clinical survival of the treatments in the long term(AU)

Retention of zirconia crowns to Ti-base abutments: effect of luting protocol, abutment treatment and autoclave sterilization.

PURPOSE: To evaluate the influence of resin cement type, surface pretreatment and autoclave sterilization on the retention of Y-TZP crowns to Ti-base abutments. METHODS: Y-TZP crowns were designed and milled to fit Ti-base abutments. Crowns were cemented using either a conventional resin cement (conventional) with a universal adhesive or a self-adhesive resin cement (self-adhesive), both following no surface pretreatment (No) or Ti-base abutment sandblasting (SB) (n=20/group). Half of the cemented samples were subjected to in-office autoclave sterilization. Pullout testing was performed in a universal testing machine at a speed of 1 mm/min until crown displacement. Data were statistically evaluated through a linear mixed model following post hoc comparisons by LSD test. RESULTS: Pullout data as a function of cement type demonstrated higher retention for conventional relative to self-adhesive cement (p < 0.001). Ti-base sandblasting (SB) favored crown retentiveness over No pretreatment (p < 0.001). Sterilized crowns exhibited higher pullout values than non-sterile (p=0.036). All the two- and three-factor interaction analyses corroborated with the superior adhesive strength of conventional compared to self-adhesive cement (all, p < 0.011), as well as, SB relative to No pretreatment (all, p < 0.024). While autoclave sterilization maximized bond strength when self-adhesive cement (data collapsed over surface pretreatment, p < 0.050) and No pretreatment were evaluated (data collapsed over surface pretreatment, p < 0.013), no significant difference was observed for conventional resin cement (p=0.280) and SB (p=0.878) groups. CONCLUSIONS: Conventional resin cement and/or Ti-base sandblasting increased Y-TZP crown retentiveness, with no significant influence of autoclave sterilization. Autoclaving increased retentiveness when self-adhesive cement and/or no Ti-base pretreatment were used.

Screwed and cement implant prosthesis: current clinical considerations / Prótese sobre implante cimentada e parafusada: considerações clínicas atuais

ABSTRACT Introduction: There is no consensus as to which cemented or screwed retention system is best to avoid bone loss around the implant from a fixed implant-supported restoration. Objective: To evaluate the prosthesis retention systems on screw and cemented implants, regarding: bone loss, survival and failure rate, biological complications and microbiological analysis. Methods: A search was made for scientific articles that contemplated the subject through the databases Pubmed and SciELO, without period restriction. The titles, abstracts and then access to the full text has been verified. Results: It was found that excess cement may play an important role in the development of peri-implant disease. Technical failures are most seen in prosthesis retained by screws, and biological complications in cemented crowns. The success rate for both restraint systems is high, and retention-independent implant prosthesis treatment provides predictability. Conclusion: The appropriate retention system for the patient depends on several factors, including indication, advantages and disadvantages, retention provided, aesthetics and clinical performance.

RESUMO Introdução: Não há consenso sobre qual sistema de retenção, cimentado ou parafusado, é o melhor para evitar perda óssea ao redor do implante de uma restauração fixa implanto-suportada. Objetivo: Avaliar os sistemas de retenção de próteses sobre implantes parafusadas e cimentadas, quanto aos fatores: perda óssea, taxa de sobrevivência e de falhas, complicações biológicas e análises microbiológicas. Métodos: Foi realizada uma busca por artigos científicos que contemplassem o tema através das bases de dados Pubmed e SciELO, sem restrição de período. Os títulos, resumos e em seguida o acesso ao texto completo foi verificado. Resultados: Foi observado que o excesso de cimento pode desempenhar um papel importante no desenvolvimento da doença peri-implantar. Falhas técnicas são mais observadas em próteses retidas por parafusos e complicações biológicas em coroas cimentadas. A taxa de sucesso para os dois sistemas de retenção é alta e o tratamento com próteses sobre implantes independente da retenção oferece previsibilidade ao caso. Conclusão: O sistema de retenção apropriado para o paciente depende de diversos fatores, incluindo a indicação, vantagens e desvantagens, retenção fornecida, estética e desempenho clínico.

Estudo in vitro da influência de diferentes plugs coronários sobre o remanescente da obturação, após preparo para pino, na retenção de pinos metálicos fundidos / In vitro assessment of the influence of different protection plugs over obturation remnant space, after post preparation, on the retention of cast metal posts

Objetivo: Avaliar a influência de diferentes plugs de proteção, acomodados sobre o remanescente da obturação após preparo para pino, na retenção de pinos metálicos fundidos. Métodos: Cinquenta dentes bovinos foram decoronados, manualmente instrumentados até a lima manual Kerr #80 e obturados. A desobturação parcial de 10mm do conduto foi realizada com uma broca Largo e os grupos foram divididos de acordo com os diferentes materiais utilizados como plugs (n=10): Grupo I (Controle, sem plug); Grupo II (plug de Coltosol®); Grupo III (plug, em consistência de massa, de Sealapex® + óxido de zinco); Grupo IV (plug de etil-cianoacrilato); e Grupo V (plug de fosfato de zinco). Uma camada de 1mm de espessura dos diferentes plugs (Grupos II, III, IV ou V) foi acomodada sobre a obturação remanescente. Os espécimes foram selados e armazenados em 100% de umidade, por 7 dias. Após moldagem do conduto, foram confeccionados pinos metálicos fundidos e cimentados com fosfato de zinco. Os espécimes permaneceram em câmara úmida por 45 dias antes do teste de tração, realizado em uma máquina universal de ensaios. Os valores foram expressos em Mega pascal (MPa) e submetidos aos testes ANOVA e Tukey (p<0,05). Resultados: O etilcianoacrilato diminuiu a retenção dos pinos metálicos fundidos (p<0,01). Não houve diferença entre os outros grupos (p>0,05), semelhante- mente ao controle. Conclusão: A proteção da obturação com plugs confeccionados com etil-cianoacrilato prejudica a retenção de pinos metálicos fundidos cimentados com fosfato de zinco, enquanto Sealapex® acrescido de óxido de zinco, fosfato de zinco endurecido ou Coltosol® não interferem na adesividade (AU).

Evaluating efficacy of different post materials and lengths on bonding strength between root canal dentin and post restorations: An experimental study.

BACKGROUND: During post restoration, different root structures require several types of posts to increase duration of their clinical use. Several materials have been investigated to enhance their quality and optimize their length according to the available root canal. AIMS: The aim of this study was to determine the effect of zirconia, fiber, and ceromer posts with 3- and 6-mm post sizes on the bonding strength of them to root canal dentinal wall with the means of pull-out bond strength test. METHODS: Forty-eight single-rooted mandibular human premolar teeth were collected and prepared for this in vitro study. With resin cement, 3- and 6-mm study posts including zirconia, fiber, and ceromer were luted to prepare teeth. For the retention testing, the pull-out force was applied to each specimen parallel to longitudinal axis of both the post and tooth. RESULTS: Both type of materials and size of posts changed the value of bonding strength. In all the post types, 6-mm ones performed better. Overall, the best bonding strength was obtained with fiber posts and the better bonding strength was obtained with zirconia; however, ceromer provided the least bonding strength. CONCLUSION: Current experiments supported that 6-mm post size can increase the bonding between root canal dentin and studied posts. When considering post materials, fiber provided the best bonding strength in current laboratory setup. Second, zirconia had meaningfully acceptable bonding strength; however, the bonding strength of ceromer posts was not favorable. Further studies optimizing post fabrication techniques of root materials may increase the bonding strength of posts to human dentin to an acceptable clinical degree.

Prosthesis Survival Rates and Prosthetic Complications of Implant-Supported Fixed Dental Prostheses in Partially Edentulous Patients.

PURPOSE: To determine the prevalence and distribution of prosthetic complications affecting implant-supported fixed dental prostheses (ISFDPs). MATERIALS AND METHODS: Subjects previously treated with one or more ISFDP(s) were identified from an electronic health record search and recalled for comprehensive clinical examination. Past prosthesis failures and complications were identified from the patient records while any existing complications, not previously recorded, were assessed during examination. ISFDP survival and failure rates were calculated with Kaplan-Meier curves and life table analysis, while regression Poisson analysis was used to identify associations between outcomes and possible patient- and prosthesis-based risk factors. RESULTS: Seventy-four subjects with 107 ISFDPs were enrolled in the study with a mean time between prosthesis delivery and exam of 3.14 years (range: 1.00-9.00 years). Four prostheses failed, resulting in a cumulative prosthesis survival rate of 96.26%. Prosthetic complications affected 48.59% of ISFDPs, the majority (94.87%) of them minor complications. Only the use of a nightguard was associated with a lower prevalence of prosthetic screw loosening (HR 0.11, 95% CI 0.02-0.59, p = 0.007) while no outcome differences were noted for other variables. Patient satisfaction was high regardless of presence or number of complications. CONCLUSIONS: ISFDPs demonstrated a high survival rate and overall high, patient-reported satisfaction. Minor prosthetic complications were common but were only significantly associated with nightguard use.

Peri-Implant Diseases and Biologic Complications at Implant-Supported Fixed Dental Prostheses in Partially Edentulous Patients.

PURPOSE: This is a single center, retrospective study to assess the prevalence of peri-implant disease and biologic complications in a cohort of partially edentulous subjects in relation to selected prosthetic factors. MATERIALS AND METHODS: Subjects previously treated with one or more implant-supported fixed dental prosthesis (ISFDPs) were recalled for a comprehensive examination. Clinical and radiographic records were taken and questionnaires were administered. The prevalence of implant failure, peri-implant disease and other biologic complications were correlated with selected prosthetic, clinical and patient-related factors using chi-square and multiple regression analyses. RESULTS: A convenience sample of 71 subjects with 100 prostheses supported by 222 dental implants were enrolled in the study. The mean follow-up time after prosthesis delivery was 3.3 ± 1.5 years (range of 1-9 years). The cumulative implant survival rate was 99.1%. Peri-implantitis was the most frequent major biologic complication (5% of implants), while the most frequent minor biologic complication was peri-implant mucositis (84.10% of implants). A diagnosis of peri-implant mucositis was more likely associated with cement-retained prostheses compared to screw-retained prostheses (OR 6.8, 95% CI 1.1-78.6, p = 0.045) and for short-span prostheses (≤3 prosthetic units) (OR 2.3, 95% CI 1.1-5.0, p = 0.034). Subject-reported quality of life measures were high regardless of the existence of major and/or minor complications, but decreased with increasing number of minor and total biologic complications. CONCLUSIONS: Peri-implant mucositis and other minor biologic complications were highly prevalent. The distribution of the observed complications differed based on the method of prosthesis retention and the number of prosthetic units replaced.

Comparison of Retention and Seating of Implant-Supported Hard and Soft Metal Copings.

Objectives: Implant-supported restorations are generally used for the replacement of the lost teeth. Stability against masticatory forces and proper retention are critical for optimal durability of restorations. The aim of this experimental study was to compare the retention of cobalt-chromium (Co-Cr) copings made by different techniques. Materials and Methods: Twenty-four solid abutment analogs were mounted and scanned with a desktop scanner. They were divided into two groups (n=12) and received metal copings fabricated by either soft or hard Co-Cr alloy. Soft Ceramill Sintron Co-Cr patterns were milled and sintered. Hard Co-Cr blocks were milled in a milling machine. The copings were sandblasted, polished, adjusted, and placed on the respective abutments. The frequency of adjustments was recorded for each abutment. The copings were cemented with zinc phosphate cement and underwent tensile test by a universal testing machine. The Mann-Whitney test and t-test were used to compare the two groups (α=0.05). Results: There was no significant difference in retention of copings between the experimental groups. The mean retentive force was 559.58±115.66 N and 557.13 ±130.48 N for the soft and hard metal groups, respectively (P=0.96). Considering the non-normal distribution of adjustment frequency data, the Mann-Whitney test showed that the frequency of adjustments was significantly higher in the hard metal group than the soft metal group (9.5 versus 0.1667; P<0.001). Conclusion: Although hard metal copings required more adjustments, retention of soft and hard Co-Cr copings was not significantly different.