ABSTRACT
Ti-6Al-4V alloy has been widely investigated for biomedical applications due to its low density, high specific strength, and favorable corrosion resistance. However, some reported failures have imposed a challenge to improve bone regeneration and fixation, as well as antibacterial properties. A further opportunity for solving this problem is the introduction of porosity. However, this can induce metallic release and corrosion product formation. In this work, a Ti-6Al-4V alloy was exposed to Hank's solution, sterilized and inoculated with Staphylococcus aureus at 37 °C. Surface analysis was carried out by SEM-EDS and XPS. Electrochemical measurements were also performed using chronopotentiometry at open circuit potential, polarization curves, and electrochemical impedance spectroscopy. After exposure, FE-SEM showed some colonies of S. aureus on the sample with 22% porosity. However, XPS analysis revealed that the presence of bacterium influenced the composition of the oxide layer, even more drastically with the increase in added porosity. Moreover, the impedance analysis showed De Levie's behavior, revealing a reduction of pore resistance and modulus of the impedance in the low frequency range in inoculated medium, and polarization curves showed that the passivity potential range was decreased, whereas the passivity current increased in the presence of the S. aureus.
Subject(s)
Alloys/chemistry , Electrochemical Techniques/methods , Staphylococcus aureus/physiology , Titanium/chemistry , Dielectric Spectroscopy , Microscopy, Electron, Scanning , Photoelectron Spectroscopy , Porosity , Staphylococcus aureus/ultrastructureABSTRACT
The ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate and carbon black (CB) nanoparticles were incorporated within a crosslinked chitosan film over the surface of a glassy carbon electrode, and the obtained architecture explored to the sensitive voltammetric sensing of Allura red colorant in soft drinking powders. The different electrodic surfaces were morphologically and electrochemically characterized. From the modification of glassy carbon electrode with IL and CB, a significantly enhanced voltammetric response was achieved toward the Allura red irreversible oxidation reaction. The type and amount of IL employed in the electrode modification step as well as all the others experimental parameters affecting the sensor response by square-wave adsorptive anodic stripping voltammetry (SWAdASV) were systematically optimized. Under the optimum experimental conditions, the proposed SWAdASV procedure provided a linear analytical curve in the concentration range of 3.98 × 10-8 to 9.09 × 10-7 mol L-1 and a low limit of detection of 9.1 × 10-10 mol L-1 (0.91 nmol L-1). The proposed sensor presented good precision and no matrice effects as shown from repeatability tests, concomitant studies and addition/recovery assays. The developed SWAdASV procedure was applied successfully in the determination of Allura red content in commercial soft drink powder samples, and the results were in close agreement with those obtained using a comparative spectrophotometric method at a confidence level of 95%.
ABSTRACT
O desempenho de sensores fotoeletroquímicos, baseados no elétrodo Ti/TiO2 (sendo um exemplo de modelagem o sensor de hidrazina), foi descrito matematicamente e o respectivo modelo foi analisado por meio de teoria de estabilidade linear e análise de bifurcações. As condições do melhor desempenho destes sensores, bem como as de instabilidades oscilatória e monotônica, foram inferidas na base da análise do modelo.
The work of photoelectrochemical sensors, based on the Ti/TiO2 electrode (being an example for the modeling the hydrazine sensor), was described mathematically and the respective model was analyzed by means of linear stability theory and bifurcation analysis. The best response condition for this sensor, as also, the oscillatory and monotonic instabilities requirements, were inferred, basing on the model´s analysis.
ABSTRACT
The preparation and electrochemical characterization of a nickel hydroxide modified nickel electrode as well as its behavior as electrocatalyst toward the oxidation of hydrochlorothiazide (HCTZ) were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of HCTZ were explored using cyclic voltammetry. The voltammetric response of the modified electrode in the detection of HCTZ is based on the electrochemical oxidation of the Ni(II)/Ni(III) and a chemical redox process. The analytical parameters for the electrooxidation of HCTZ by the nickel hydroxide modified nickel electrode were obtained in NaOH solution, in which the linear voltammetric response was in the concentration range from 1.39×10(-5) to 1.67×10(-4)mol L(-1) with a limit of detection of 7.92×10(-6)mol L(-1) and a sensitivity of 0.138 µA Lmmol(-1). Tafel analysis was used to elucidate the kinetics and mechanism of HCTZ oxidation by the modified electrode.