Chemical improvement of soluble rocks: Foundation of Mosul Dam as case study.

The dissolution of soluble rocks (gypsum/anhydrite) beneath the Mosul Dam by water seepage has been observed upon the initial impoundment; consequently, several sinkholes have been manifested in the vicinity of the dam site. Traditional grouting has been envisaged as a potential remedy; however this measure has not eradicated the problem. The main purpose of this study is to overcome the solubility of the gypsum/anhydrite rocks using chemical grouts. Rock samples were acquired from the Fatha Formation outcrop and problematic layers of brecciated gypsum situated at varying depths beneath the Mosul Dam. Two commercially available liquid polymers, polyurethane (PU) and a mixture of acrylic and cement (ARC) were used to investigate their sealing performance in halting of the solubility of the rocks (gypsum/anhydrite). To simulate the dissolution phenomenon under the influence of artificial hydraulic pressure of the dam and the water flow in its abutments, two distinct laboratory models were devised. The outcomes from the experimental study on both untreated and treated samples revealed that the acrylic-cement composite (ARC) and polyurethane (PU) are influential polymers in halting the solubility of the gypsum rock samples under both factors of water pressure and high-velocity water flow.

Effect of Fiber Loading on Mechanical and Flame-Retardant Properties of Poplar-Fiber-Reinforced Gypsum Composites.

Gypsum-based composites were prepared via a slurry casting process using construction gypsum as the binding material and poplar fibers as reinforcing material. The effects of different fiber content and curing time on the mechanical properties, water resistance, and flame retardancy of these composites were investigated, and the influence mechanism was characterized by infrared spectroscopy, scanning electron microscopy, and X-ray diffractometry. The results showed that the best composite mechanical strength was achieved with 10% poplar fiber- content, and the absolute dry flexural and compressive strengths reached 3.59 and 8.06 MPa, respectively. Compared with pure gypsum, the flexural strength and compressive strength increased by 10% and 19%, respectively. The inclusion of fibers somewhat prevented the migration of free water within the composites and enhanced their water resistance. At 10% fiber content, the composite's 24 h water absorption rate was 34.3%, 8% lower than that of pure gypsum, with a softening coefficient of 0.55. However, fiber content increases the porosity of gypsum-based composites. When heated, this increased porosity accelerates' heat conduction within the matrix, raising the peak and total exothermic rates, thereby weakening the composites' inherently flame-retardant properties. Poplar-fiber-reinforced gypsum-based composites offered superior performance in commercial applications, compared to pure gypsum board, providing a sustainable and green alternative for ceilings, partitions, and other applications, while broadening the prospects for gypsum-based composites in the engineering field.

Impact of Superplasticizers on the Performance of Low-Grade Limestone-Based Cement Mixes.

Low-grade limestone (LGL) is not used to produce cement clinker, but this leftover material in cement quarries increases the water demand when used as a filler in concrete production. In this study, the effect of six commercial superplasticizers on the performance of cement mixes containing 35% LGL and 2% gypsum was investigated. The optimal doses of these superplasticizers were found in a range of different water/binder (w/b) ratios by conducting several Marsh cone and mini-slump tests. The addition of a superplasticizer with a higher active solid content produced a maximum cement flow, regardless of the w/b ratios. The LGL-based mortar samples admixed with this superplasticizer obtained a maximum compressive strength of about 36 MPa at the end of 28 days. SEM and XRD results showed the formation of a new calcium-rich mineral in their microstructure. These findings highlight the impact of the type and properties of superplasticizers on the performance of concrete mixes containing LGL as a supplementary cementitious material.

MgO-based supersulfated cement with different industrial by-product gypsum: Experiments and molecular dynamics simulation.

Super sulfate cement (SSC) emerges as a sustainable alternative to ordinary Portland cement, boasting minimal carbon emissions and exceptional performance. As the quest for eco-friendly alternatives intensifies, there's a growing focus on exploring alkaline and sulfate activators conducive to SSC's environmental goals. This study delves into the viability of utilizing MgO as an alkaline activator in producing MgO-based supersulfated cement, while also investigating the impact of various industrial by-product gypsums on its performance. Findings reveal that employing MgO as an alkaline activator yields favorable hydration properties and mechanical strength in SSC. The optimized formulation comprises 15 % industrial by-product gypsum, 83 % granulated blast furnace slag (GGBFS), and 2 % MgO. Incorporating building gypsum and flue gas desulfurization (FGD) gypsum demonstrates superior unconfined compressive strength (UCS) growth compared to citric gypsum and phosphogypsum. Notably, gel-pores below 20 nm dominate the matrix, with variations in their distribution linked to the gypsum type used. The pH level and crystal structure of the industrial by-product gypsum emerge as pivotal factors dictating the hydration process. The interaction energy between hydrated building gypsum crystal planes and water molecules proves lower, contributing to the root cause of its high sulfate activating capability. Compared to traditional SSC, MgO-based supersulfated cement requires less alkaline activator content and accommodates more industrial by-product gypsums, thus reducing costs, CO2 emissions, and promoting the efficient utilization of these solid wastes.

A critical review on the use of flue gas desulfurization gypsum to ameliorate saline-alkali soils and its prospect for reducing carbon emissions.

Flue gas desulfurization gypsum (FGDG), a solid waste produced during sulfur removal in coal-fired power plants, has applications in saline-alkali soil amelioration due to its function of calcium­sodium ion exchange. Existing research has focused on the use of gypsum to improve saline-alkali soils in non-coastal areas. However, coastal areas are not only extensively salinized, but an important source of methane, and surprisingly, FGDG may assist to decrease methane formation mainly by the action of sulfate radical. This is the first critical review to systematically discuss the effects of FGDG on both saline-alkali soil improvement and carbon emission control in tidal flats, including application status, amendment principles, environmental risks and methane emission control. After adding FGDG, soil salinization degree was weakened via adjusting soil structure, pH, exchangeable sodium percentage and electric conductivity, introduction of nutrients also promotes crop growth. The optimal FGDG dosage in tidal flats seems to be higher (>2 %) than that in non-coastal areas (<1 %). Its environmental risks regarding heavy metals and eutrophication are evaluated safe. In tidal areas, more methane is produced in hot seasons and ebb tides. Plants and invertebrates also promote methane release. FGDG controls methane production by promoting the activity of sulfate-reducing bacteria and inhibiting methanogens. Considering methane flux levels and seawater erosion, FGDG use in low tidal beach needs more research, while that in high and middle tidal beach is recommended. This review will expand applications and appropriate use of FGDG for reducing carbon emission and improving ecological services in coastal areas.

Gypsum Cave Biofilm Communities are Strongly Influenced by Bat- And Arthropod-Related Fungi.

The Gypsum Karst of Sorbas, Almeria, southeast Spain, includes a few caves whose entrances are open and allow the entry and roosting of numerous bats. Caves are characterized by their diversity of gypsum speleothems, such as stalactites, coralloids, gypsum crusts, etc. Colored biofilms can be observed on the walls of most caves, among which the Covadura and C3 caves were studied. The objective was to determine the influence that bat mycobiomes may have on the fungal communities of biofilms. The results indicate that the fungi retrieved from white and yellow biofilms in Covadura Cave (Ascomycota, Mortierellomycota, Basidiomycota) showed a wide diversity, depending on their location, and were highly influenced by the bat population, the guano and the arthropods that thrive in the guano, while C3 Cave was more strongly influenced by soil- and arthropod-related fungi (Ascomycota, Mortierellomycota), due to the absence of roosting bats.

[Effects of Different Modified Materials on Soil Fungal Community Structure in Saline-Alkali Soil].

Studying the effects of different modified materials on the physicochemical properties and fungal community structure of saline-alkali soil can provide theoretical basis for reasonable improvement of saline-alkali soil. High-throughput sequencing technology was used to explore the effects of five treatments, namely, control (CK), desulfurization gypsum (T1), soil ameliorant (T2), organic fertilizer (T3), and desulfurization gypsum compounds soil ameliorant and organic fertilizer (T4), on soil physicochemical properties and fungal community diversity, composition, and structure of saline-alkali soil in Hetao Plain, Inner Mongolia. The results showed that compared with those in CK, the contents of available phosphorus, available potassium, organic matter, and alkali hydrolysis nitrogen were significantly increased in modified material treatments, and the T4 treatment significantly decreased soil pH. Modified treatments increased the Simpson and Shannon indexes of fungi but decreased the Chao1 index. The dominant fungi were Ascomycota, Basidiomycota, and Mortierellomycota, and the dominant genera were Mortierella, Conocybe, Botryotrichum, Fusarium, and Pseudogymnoascus. The application of modified materials increased the relative abundance of Ascomycota, Basidiomycota, Fusarium, and Pseudogymnoascus, while decreasing the relative abundance of Mortierellomycota, Chytridiomycota, and Mortierella. LEfSe analysis showed that modified treatments altered the fungal community biomarkers. Correlation analysis showed that pH and available potassium were the main environmental factors affecting fungal community structure. The results can provide scientific basis for improving saline-alkali soil and increasing soil nutrients in Hetao Plain, Inner Mongolia.

Synergistic effect of biochar with gypsum, lime, and farm manure on the growth and tolerance in rice plants under different salt-affected soils.

Soil salinization and sodication harm soil fertility and crop production, especially in dry regions. To combat this, using biochar combined with gypsum, lime, and farm manure is a promising solution for improving salt-affected soils. In a pot experiment, cotton stick biochar (BC) was applied at a rate of 20 t/ha in combination with gypsum (G), lime (L), and farm manure (F) at rates of 5 and 10 t/ha. These were denoted as BCG-5, BCL-5, BCF-5, BCG-10, BCL-10, and BCF-10. Three different types of soils with electrical conductivity (EC) to sodium adsorption ratio (SAR) ratios of 2.45:13.7, 9.45:22, and 11.56:40 were used for experimentation. The application of BCG-10 led to significant improvements in rice biomass, chlorophyll content, and overall growth. It was observed that applying BCG-10 to soils increased the membrane stability index by 75% in EC:SAR (2.45:13.7), 97% in EC:SAR (9.45:22), and 40% in EC:SAR (11.56:40) compared to respective control treatments. After BCG-10 was applied, the hydrogen peroxide in leaves dropped by 29%, 23%, and 21% in EC:SAR (2.45:13.7), EC:SAR (9.45:22), and EC:SAR (11.56:40) soils, relative to their controls, respectively. The application of BCG-10 resulted in glycine betaine increases of 60, 119, and 165% in EC: SAR (2.45:13.7), EC: SAR (9.45:22), and EC: SAR (11.56:40) soils. EC: SAR (2.45:13.7), EC: SAR (9.45:22), and EC: SAR (11.56:40) soils all had 70, 109, and 130% more ascorbic acid in BCG-10 applied treatment, respectively. The results of this experiment show that BCG-10 increased the growth and physiological traits of rice plants were exposed to different levels of salt stress. This was achieved by lowering hydrogen peroxide levels, making plant cells more stable, and increasing non-enzymatic activity.

The antipyretic effect of the famous classical formula Qingwanzi Pills on a rabbit model and its serum metabolomic study.

Qingwanzi Pills (QP) were first mentioned in the "Puji Fang" of the Ming Dynasty, with a history of approximately 600 years. The formula consisted of Gypsum Fibrosum and Indigo Naturalis. It is a famous classical formula with antipyretic effects frequently utilized in ancient China, although our knowledge about the overall antipyretic mechanism of QP remains limited. Therefore, we replicated the fever model in New Zealand rabbits induced by lipopolysaccharide, performed the pharmacodynamic evaluation of QP, identified the differential metabolites among QP groups, and performed pathway enrichment analysis to comparatively analyze the effects of QP on fever-related metabolic pathways by ultra-performance liquid chromatography-mass spectrometry. The results showed that the antipyretic effect of QP was superior to that of each disassembled prescription, with Gypsum Fibrosum primarily contributing to the efficacy, followed by Indigo Naturalis and Junci Medulla. QP had an effective antipyretic effect, which was related to lowering the levels of TNF-α, IL-6, IL-1ß, and calcium in rabbit serum, lowering the levels of PGE2 and cAMP in rabbit cerebrospinal fluid, and increasing the level of calcium in rabbit cerebrospinal fluid. A total of 27 endogenous biomarkers were screened by serum metabolomics for the treatment of fever with QP. It is hypothesized that the antipyretic mechanism of QP may be related to regulating α-linolenic acid, sphingolipid, tryptophan, and bile acid metabolism. In summary, QP exhibited a significant antipyretic effect in rabbits with lipopolysaccharide-induced fever.

The Roles of Oil-Water Interfaces in Forming Ultrasmall CaSO4 Nanoparticles.

In natural and engineered environmental systems, calcium sulfate (CaSO4) nucleation commonly occurs at dynamic liquid-liquid interfaces. Although CaSO4 is one of the most common minerals in oil spills and oil-water separation, the mechanisms driving its nucleation at these liquid-liquid interfaces remain poorly understood. In this study, using in situ small-angle X-ray scattering (SAXS), we examined CaSO4 nucleation at oil-water interfaces and found that within 60 minutes of reaction, short rod-shaped nanoparticles (with a radius of gyration (Rg) of 17.2 ± 2.7 nm and a length of 38.2 ± 5.8 nm) had formed preferentially at the interfaces. Wide-angle X-ray scattering (WAXS) analysis identified these nanoparticles as gypsum (CaSO4·2H2O). In addition, spherial nanoparticles measuring 4.1 nm in diameter were observed at oil-water interfaces, where surface-enhanced Raman spectroscopy (SERS) revealed an elevated pH compared to the bulk solution. The negatively charged oil-water interfaces preferentially adsorb calcium ions, collectively promoting CaSO4 formation there. CaSO4 particle formation at the oil-water interface follows a nonclassical nucleation (N-CNT) pathway by forming ultrasmall amorphous spherical particles which then aggregate to form intermediate nanoparticles, subsequently growing into nanorod-shaped gypsum. These findings of this study provide insights into mineral scaling during membrane separation and can inform more efficient oil transport in energy recovery systems.

Effect of Mineral Admixtures on Physical, Mechanical, and Microstructural Properties of Flue Gas Desulfurization Gypsum-Based Self-Leveling Mortar.

The production of flue gas desulfurization gypsum poses a serious threat to the environment. Thus, utilizing gypsum-based self-leveling mortar (GSLM) stands out as a promising and effective approach to address the issue. ß-hemihydrate gypsum, cement, polycarboxylate superplasticizer, hydroxypropyl methyl cellulose ether (HPMC), retarder, and defoamer were used to prepare GSLM. The impact of mineral admixtures (steel slag (SS), silica fume (SF), and fly ash (FA)) on the physical, mechanical, and microstructural properties of GSLM was examined through hydration heat, X-ray diffractometry (XRD), Raman spectroscopy, and scanning electron microscopy (SEM) analyses. The GSLM benchmark mix ratio was determined as follows: 94% of desulfurization building gypsum, 6% of cement, 0.638% each of water reducer and retarder, 0.085% each of HPMC and defoamer (calculated additive ratio relative to gypsum), and 0.54 water-to-cement ratio. Although the initial fluidity decreased in the GSLM slurry with silica fume, there was minimal change in 30 min fluidity. Notably, at an SS content of 16%, the GSLM exhibited optimal flexural strength (6.6 MPa) and compressive strength (20.4 MPa). Hydration heat, XRD, and Raman analyses revealed that a small portion of SS actively participated in the hydration reaction, while the remaining SS served as a filler.

A Study of the Influence of Cement Addition and Humidity on the Mechanical Strength and Microstructure of Flue Gas Desulfurization Gypsum-Cement Plasters.

Over the last 20 years, flue gas desulfurization gypsum (FGD gypsum) has become a valuable and widely used substitute for a natural raw material to produce plasters, mortars, and many other construction products. The essential advantages of FGD gypsum include its high purity and stability, which allow for better technical parameters compared to natural gypsum, and, until recently, its low price and easy availability. This FGD gypsum is obtained in the process of desulfurization of flue gases and waste gases in power plants, thermal power plants, refineries, etc., using fossil fuels such as coal or oil. The gradual reduction in energy production from fossil raw materials implemented by European Union countries until its complete cessation in 2049 in favor of renewable energy sources significantly affects the availability of synthetic gypsum, and forces producers of mortars and other construction products to look for new solutions. The gypsum content in commonly used light plaster mortars is usually from 50 to 60% by mass. This work presents the results of tests on mortars wherein the authors reduced the amount of gypsum to 30%, and, to meet the strength requirements specified in the EN 13279-1:2008 standard, added Portland cement in the amount of 6-12% by mass. Such a significant reduction in the content of synthetic gypsum will reduce this raw material's consumption, thus extending its availability and developing other solutions. The study presented the test results on strength, density, porosity, pore size distribution, and changes in the microstructure of mortars during up to 180 days of maturation in conditions of increased relative humidity. The results show that decreased porosity and increased mechanical strength occur due to the densification of the microstructure caused by the formation of hydration products, such as C-S-H, ettringite, and thaumasite.

Shipwrecked on the Rock, or Not Quite: Gypsophytes and Edaphic Islands.

Species-area relationships (SAR) constitute a key aspect of ecological theory and are integral to other scientific disciplines, such as biogeography, which have played a crucial role in advancing biology. The theory of insular biogeography provides a clear example. This theory initially expanded from true islands to other types of systems characterized by their insularity. One such approach was linked to geoedaphic islands, as seen in gypsum outcrops. While these continental areas have been considered insular systems, only limited and mostly indirect evidence thereof has been provided. This study utilized SAR to advance the understanding of gypsum outcrops as insular continental territories. It is hereby hypothesized that gypsum outcrops are edaphic islands, although their insular nature depends on the different functional or ecological plant types, and this nature will be reflected in the potential Arrhenius model z values. The results obtained support both hypotheses and provide insight into the ecological factors that help interpret the insularity of these areas. This interpretation goes beyond their mere extent and the distance among outcrops, emphasizing the importance of environmental filters. Said filters vary in permeability depending on the degree of gypsophily, or preference for gypsum, exhibited by different species.

Synthesis and Characterisation of Hemihydrate Gypsum-Polyacrylamide Composite: A Novel Inorganic/Organic Cementitious Material.

This study combined inorganic α-hemihydrate gypsum (α-HHG) with organic polyacrylamide (PAM) hydrogel to create a novel α-HHG/PAM composite material. Through this facile composite strategy, this fabricated material exhibited a significantly longer initial setting time and higher mechanical strength compared to α-HHG. The effects of the addition amount and the concentration of PAM precursor solution on the flowability of the α-HHG/PAM composite material slurry, initial setting time, and mechanical properties of the hardened specimens were investigated. The structural characteristics of the composite material were examined using XRD, FE-SEM, and TGA. The results showed that the initial setting time of the α-HHG/PAM composite material was 25.7 min, which is an extension of 127.43% compared to that of α-HHG. The flexural strength and compressive strength of the oven-dried specimens were 23.4 MPa and 58.6 MPa, respectively, representing increases of 34.73% and 84.86% over values for α-HHG. The XRD, FE-SEM, and TGA results all indicated that the hydration of α-HHG in the composite material was incomplete. The incompleteness is caused by the competition between the hydration process of inorganic α-HHG and the gelation process of the acrylamide molecules for water, which hinders some α-HHG from entirely reacting with water. The enhanced mechanical strength of the α-HHG/PAM composite material results from the tight interweaving and integrating of organic and inorganic networks. This study provides a concise and efficient approach to the modification research of hemihydrate gypsum.

Assessment of the Thermal Properties of Gypsum Plaster with Plastic Waste Aggregates.

Building material manufacturers must support new production models that encourage the manufacture of more efficient and sustainable products. This includes thinking about savings in the use of raw materials, a contribution to the energy efficiency of buildings during their useful life, and a reduction in the generation and deposit of waste in landfills. In this research, an analysis of the thermal properties of gypsum composites added with plastic waste is carried out using the most common methods, the steady state method and the transient plane source method, and the effect of water saturation on these composites is tested. The results show an improvement in the thermal performance of the composites (values reduced with respect to the reference by 4-7%), despite their heterogeneity, as well as a variation in the measurements carried out, depending on the method used for the measurements (variation up to 10%). It is also found that the degree of humidity negatively affects the thermal conductivity coefficient but, on the contrary, this coefficient is not altered in the composites with plastic waste, due to their lower hygroscopicity. Therefore, it is considered that the proposed eco-plasters are a good alternative to traditional plasters, with which to contribute to the achievement of the objectives of the current European directives on waste and circular economy.

Sustainable Dentistry: A Comprehensive Review of the Recycling Techniques for Gypsum Products in Prosthodontics.

This review explores the pivotal role of sustainable dentistry with a specific focus on the recycling of gypsum products in prosthodontics. As oral health practices increasingly impact the environment, the adoption of sustainable approaches becomes imperative. The review delves into the environmental challenges posed by gypsum waste in prosthodontics and examines current recycling techniques, presenting key findings and successful case studies. The call to action is directed towards the dental community, urging practitioners, educators, and policymakers to prioritize sustainable practices, encompassing responsible waste management and the incorporation of eco-friendly materials. Looking to the future, the review envisions a promising landscape for sustainable dentistry in prosthodontics, propelled by emerging technologies and a collective commitment to environmentally conscious oral healthcare. Ultimately, this review serves as a catalyst for positive change, advocating for a transformative shift toward sustainability within the dental community.

Elucidating Amendment Resources for Reclaiming Efficacy of Sodic Soils around Abaya and Chamo Lakes, South Ethiopia Rift Valley.

BACKGROUND: Sodic soils are harmful to agricultural and natural environments in Ethiopia's semi-arid and arid regions, leading to soil degradation and reduced productivity. This study investigated how amendment resources could help improve the chemical properties of sodic soils around the Abaya and Chamo Lakes in the South Ethiopia Rift Valley. METHODS: A factorial experiment was conducted to study the effects of gypsum (GYP) and farmyard manure (FYM) on sodic soil reclamation. The experiment had four levels of GYP (0, 50, 100, and 150%) and four levels of FYM (0, 10, 20, and 30 tons ha-1), with three replications. The pots were incubated for three months and leached for one month, after which soil samples were collected and analyzed for chemical properties. ANOVA was performed to determine the optimal amendment level for sodic soil reclamation. RESULTS: The study found that applying 10 ton FYM ha-1 and gypsum at 100% gypsum required (GR) rate resulted in a 99.8% decrease in exchangeable sodium percentages (ESP) compared to untreated composite sodic soil and a 1.31% reduction over the control (GYP 0% + FYM 0 ton ha-1). As a result, this leads to a decrease in soil electrical conductivity, exchangeable sodium (Ex. Na), and ESP values. The results were confirmed by the LSD test at 0.05. It is fascinating to see how different treatments can have such a significant impact on soil properties. The prediction models indicate that ESP's sodic soil treatment effect (R2 = 0.95) determines the optimal amendment level for displacing Ex. Na from the exchange site. The best estimator models for ESP using sodic soil treatment levels were ESP = 1.65-0.33 GYP for sole gypsum application and ESP = 1.65-0.33 GYP + 0.28 FYM for combined GYP and FYM application, respectively. CONCLUSION: The study found that combined GYP and FYM applications reduced ESP to less than 10% in agriculture, but further research is needed to determine their effectiveness at the field level.

Application of the Industrial Byproduct Gypsum in Building Materials: A Review.

The industrial byproduct gypsum is a general term for byproducts discharged from industrial production with calcium sulfate as the main ingredient. Due to the high number of impurities and production volume, the industrial byproduct gypsum is underutilized, leading to serious environmental problems. At present, only desulfurization gypsum and phosphogypsum have been partially utilized in cementitious materials, cement retarders, etc., while the prospects for the utilization of other byproduct gypsums remain worrying. This paper mainly focuses on the sources and physicochemical properties of various types of gypsum byproducts and summarizes the application scenarios of various gypsums in construction materials. Finally, some suggestions are proposed to solve the problem of the industrial byproduct gypsum. This review is informative for solving the environmental problems caused by gypsum accumulation.

Eco-Design and Characterization of Sustainable Lightweight Gypsum Composites for Panel Manufacturing including End-of-Life Tyre Wastes.

The incorporation of rubber recycled aggregates from end-of-life tyres (ELT) in the manufacturing process of sustainable building materials has gained great interest in recent decades as a result of the large volume of this waste being generated annually. In this work, the objective is to make a contribution towards the circularity of construction products by carrying out a physico-mechanical characterisation of new gypsum composites made with the incorporation of these recycled rubber aggregates. To this end, up to 30% by volume of the original raw material has been substituted, analysing the mechanical resistance to bending and compression. Although lower than those of traditional gypsum material, both properties exceed the limits set at 1 and 2 MPa, respectively, by the current regulations. In addition, water absorption by capillarity significantly decreases, and thermal conductivity is reduced by more than 35% with respect to the reference material. Finally, in order to provide the research with a practical application, a prefabricated plate design has been proposed that incorporates the gypsum materials studied and an agglomerated rubber band that increases the thermal resistance and improves the efficiency of the designed construction system. In this way, this research reflects the potential of these novel building materials and explores new avenues for their application in building construction.

[Research progress in pharmacological effects of Gypsum Fibrosum and material basis for its heat-clearing effect].

Gypsum Fibrosum, as a classic heat-clearing medicine, is widely used in the clinical practice of traditional Chinese medicine(TCM). However, debates exist about the material basis and mechanism of its efficacy. Therefore, this paper reviewed the recent research progress in the heat-clearing effect and mechanism of Gypsum Fibrosum and discussed the material basis for the heat-clearing effect of this medicine. Ca~(2+) may inhibit the upward movement of temperature set point by regulating the Na~+/Ca~(2+) level in the heat-regulating center. Moreover, trace elements may inhibit the rise of body temperature by regulating the immune system, promoting the absorption of Ca~(2+), and affecting the synthesis of prostaglandin E2(PGE2). This review aims to enrich the knowledge about the mechanism of Gypsum Fibrosum in clearing heat and provides a scientific basis for the clinical application and further development of Gypsum Fibrosum.