Alcohol-based hydrophobic deep eutectic solvents and ultrasound-assisted liquid phase microextraction followed by GC-MS for the extraction and analysis of organophosphorus pesticides in the blood of farmers.

Organophosphorus pesticides (OPPs) are a group of pesticides that are most widely used in the agricultural sector, and farmers are exposed to these chemicals more than other members of society. In this work, an environmentally friendly, simple, and safe ultrasound-assisted dispersive liquid-liquid microextraction (USA-DLLME) method using alcohol-based hydrophobic deep eutectic solvents (HDESs) followed by gas chromatography-mass spectroscopy (GC-MS) was developed for the extraction and determination of OPPs in the blood of farmers studied in Ravansar cohort. DESs synthesized from thymol as hydrogen bond donor (HBD) and aliphatic alcohols as hydrogen bond acceptor (HBA) have been used as extractants. Under optimal experimental conditions, the reproducibility of the method based on 7 replicate measurements of 10 µg L-1 of OPPs in blood samples was in the range of 1.4-3.8%. The method showed a linearity in the range of 0.01-150 µg L-1. The limits of detection and limits of quantification were between 0.003 and 0.02 µg L-1 and 0.01-0.05 µg L-1, respectively. The matrix effect and accuracy of the method were confirmed by spiking different amounts of OPPs in real blood samples and obtaining relative recoveries in the range of 91-112%. The results showed that the concentration of OPPs in the case group was significantly higher than in the control group, which is because the case group was exposed to OPPs during the spraying of agricultural products.

[Rapid determination of nine preservatives in tobacco flavor by three phase-hollow fiber-liquid phase microextraction-high performance liquid chromatography].

Tobacco flavors are extensively utilized in traditional tobacco products, electronic nicotine, heated tobacco products, and snuff. To inhibit fungal growth arising from high moisture content, preservatives such as benzoic acid (BA), sorbic acid (SA), and parabens are often incorporated into tobacco flavors. Nonetheless, consuming preservatives beyond safety thresholds may pose health risks. Therefore, analytical determination of these preservatives is crucial for both quality assurance and consumer protection. For example, BA and SA can induce adverse reactions in susceptible individuals, including asthma, urticaria, metabolic acidosis, and convulsions. Parabens, because of their endocrine activity, are classified as endocrine-disrupting chemicals. Despite extensive research, the concurrent quantification of trace-level hydrophilic (BA and SA) and hydrophobic (methylparaben, ethylparaben, isopropylparaben, propylparaben, butylparaben, isobutylparaben, and benzylparaben) preservatives in tobacco flavors remains challenging. Traditional liquid phase extraction coupled with high performance liquid chromatography (HPLC) often results in high false positive rates and inadequate sensitivity. In contrast, tandem mass spectrometry offers high sensitivity and specificity; however, its widespread application is limited by laborious sample preparation and significant operational costs. Therefore, it is crucial to establish a fast and sensitive sample pretreatment and analysis method for the nine preservatives in tobacco flavors. In this study, a method for the simultaneous determination of the nine preservatives (SA, BA and seven parabens) in tobacco flavor was established based on three phase-hollow fiber-liquid phase microextraction (3P-HF-LPME) technology combined with HPLC. To obtain the optimal pretreatment conditions, extraction solvent type, sample phase pH, acceptor phase pH, sample phase volume, extraction time, and mass fraction of sodium chloride, were examined. Additionally, the HPLC parameters, including UV detection wavelength and mobile phase composition, were refined. The optimal extraction conditions were as follows: dihexyl ether was used as extraction solvent, 15 mL sample solution (pH 4) was used as sample phase, sodium hydroxide aqueous solution (pH 12) was used as acceptor phase, and the extraction was carried out at 800 r/min for 30 min. Chromatographic separation was accomplished using an Agilent Poroshell 120 EC-C18 column (100 mm×3 mm, 2.7 µm) and a mobile phase comprising methanol, 0.02 mol/L ammonium acetate aqueous solution (containing 0.5% acetic acid), and acetonitrile for gradient elution. Under the optimized conditions, the nine target analytes showed good linear relationships in their respective linear ranges, the correlation coefficients (r) were ≥0.9967, limits of detection (LODs) and quantification (LOQs) were 0.02-0.07 mg/kg and 0.08-0.24 mg/kg, respectively. Under two spiked levels, the enrichment factors (EFs) and extraction recoveries (ERs) of the nine target analytes were 30.6-91.1 and 6.1%-18.2%, respectively. The recoveries of the nine target analytes ranged from 82.2% to 115.7% and the relative standard deviations (RSDs) (n=5) were less than 14.5% at low, medium and high levels. The developed method is straightforward, precise, sensitive, and well-suited for the rapid screening of preservatives in tobacco flavor samples.

Investigation of biodistribution by liquid-phase microextraction: Using a fatal diphenidol poisoning case.

Liquid-phase microextraction (LPME) possesses a high potential to isolate organic substances from different sample matrices. In this work, LPME was applied for the first time to investigate the biodistribution of diphenidol in different biofluids, organs, and brain regions using a fatal poisoning case. Since the LPME of diphenidol hasn't been reported, the effect of supported liquid membrane (SLM), acceptor and donor phases, and extraction time on LPME performance was investigated first. The solvents of 2-nonanone and 2-nitrophenyl octyl ether (NPOE) were found to be stable and efficient SLMs for LPME of diphenidol from biofluids and tissue samples, respectively. At steady state, the LPME recoveries for different sample matrices were in the range of 87 %-91 %. Due to the clean-up capability of LPME and the relatively high concentration of diphenidol in the fatal poisoning case, the proposed LPME systems were validated with related sample matrices using HPLC-UV for the determination. The methods displayed good linearity (R² ≥ 0.9943), and the limits of detection were 0.30 mg L-1, 0.28 mg L-1, and 2.7 µg g-1 for blood, urine, and liver samples, respectively. Meanwhile, the precision (≤13%), accuracy (90-110%), and matrices effect (±15%) were satisfactory at low, medium, and high concentrations. In addition, the stability, carryover, and dilution integrity met the requirements of ASB Standard 036. Finally, the proposed method was successfully applied to evaluate the biodistribution of diphenidol in five different biofluids, five organs, and six brain regions from a fatal poisoning case. Generally, the distribution of diphenidol in biofluids was lower than that in the organs and brain regions, and the highest concentration of diphenidol was observed in the liver, which is very important for the selection of inspection samples in forensic toxicological analysis. Therefore, LPME was proved to be a powerful tool for the investigation of biodistribution and postmortem redistribution in the fields of forensics.

Hexafluoroisopropanol-based supramolecular solvent for liquid phase microextraction of pesticides in milk.

Residues of pesticides in milk may pose a threat to human health. This study aimed to develop a liquid-phase microextraction (LPME) method using hexafluoroisopropanol (HFIP)-based supramolecular solvent (SUPRAS) for the simultaneous extraction and purification of four pesticides (boscalid, novaluron, cypermethrin and bifenthrin) in milk. Pesticides were extracted using SUPRAS prepared with nonanol and HFIP, and the extraction efficiency was analyzed. Results showed satisfactory recoveries ranging from 80.8%-111.0%, with relative standard deviations (RSDs) of <6.4%. Additionally, satisfactory linearities were observed, with correlation coefficients >0.9952. The limits of quantification (LOQs) were in the range of 1.8 µg·L-1-14.0 µg·L-1. The established method demonstrated high extraction efficiency with a short operation time (15 mins) and low solvent consumption (2.7 mL). The HFIP-based SUPRAS LPME method offers a convenient and efficient approach for the extraction of pesticides from milk, presenting a promising alternative to conventional techniques.

Development of analytical method for determination of 1,3-dimethylamylamine in sports nutrition and bodybuilding supplements using pH-switchable deep eutectic solvents followed by high-performance liquid chromatography-diode array detector.

In this work, an easy, safe, simple, and efficient pH-switchable deep eutectic solvents (DESs)-based liquid phase microextraction followed by high-performance liquid chromatography-diode array detector analysis was developed for the determination of 1,3-dimethylamylamine (DMAA). The switchability of the obtained DESs was investigated by changing the pH. Then the best-selected DES was characterized and the application of the selected DES in the extraction of DMAA from sports nutrition and bodybuilding supplements was investigated. The DES synthesized from l-menthol: oleic acid in a molar ratio of 1:2 had the highest efficiency in the extraction of the target compound. Under the optimum conditions, (50 µL of DES, 100 µL of 4 mol/L KOH, 100 µL of 4 mol/L HCl, extraction time of 40 s and without salt addition) the calibration graph was linear in the range of 0.05-100 µg/kg and limit of detection was 0.02 µg/kg. The relative standard deviations including intra-day and inter-day for 10.0 µg/kg of DMAA in real samples were 2.7% (n = 7) and 5.3% (n = 7), respectively. The enrichment factor and percentage extraction recovery of the method were 283 and 85%, respectively. The relative recoveries for DMAA in different samples were in the range of 90%-109%.

A novel indicator for lead poisoning beyond blood lead level: Facile diagnosis of lead poisoning using random urine with point-of-care testing.

Lead (Pb) poisoning is estimated to account for 1 % of the global disease burden. The gold standard for diagnosing lead poisoning in human body relies on blood lead level (BLL), which is always performed in hospitals using expensive instruments. However, there are still many countries and regions with a lack of medical resources (without enough professional medical staff and analytical instruments). To achieve a facile diagnosis of lead poisoning by ordinary residents (without any expertise), this study conducted a research study on 810 participants to discover and validate a new lead poisoning indicator (creatinine-corrected urinary lead level, cULL) beyond BLL in non-invasive samples. A point-of-care testing (POCT) device to measure cULL was developed, equipped with liquid-phase microextraction and electromembrane extraction on a paper-based analytical device for on-site separation of lead and creatinine in the urine, using a smartphone for the quantification of analytes. The cULL as a novel indicator and the POCT device developed could be effective in reducing the risk of damage from lead contamination.

Rhamnolipids-based bio-supramolecular solvents as green and sustainable media for extraction of pyrethroid insecticides in water and food matrices.

A novel bio-supramolecular solvent (bio-SUPRAS) based on rhamnolipids (RLs) was designed for efficient extraction of pyrethroid insecticides in water and food matrices. Benefiting from RLs as amphiphiles equipped with the attractive properties of bio-degradable, low toxicity and high stability, bio-SUPRAS was spontaneously generated through salt induced coagulation. The bio-SUPRAS was characterized by cryo-scanning electron microscope and main factors influencing the extraction performance were investigated in detail. Under the optimized conditions, the method was found to have desirable limits of detection (5∼10 µg l-1), good precision (RSDs<16.9 %) and satisfactory recovery (75.2 %∼94.3 %). More importantly, the extraction mechanism was studied by density functional theory systematically. Following greenness assessment, the technique was successfully used for enrichment of pyrethroid pesticides in real samples before HPLC-UV analysis. Thus, the method showed the outstanding merits of eco-efficient, green, time-saving, and had favorable application prospect to remove trace analytes from intricate sample matrices.

A configuration for cooling assisted organic solvent coated thin film microextraction after dispersive liquid-liquid microextraction method: A microextraction method for ultra-trace analyzing of volatile sample.

A combination of the dispersive liquid-liquid microextraction (DLLME) method based on the total vaporization procedure and cooling-assisted organic solvent-coated thin film microextraction (TFME) was applied for extracting chlorpyrifos (as the model compound). Based on the high thermal conductivity, a nickel foam thin film with the dimensions of 5.0 mm × 5.0 mm was used as a substrate for holding the organic solvent. Supporting thin film by organic solvent increases the thickness and contact area of the film relative to TFME or single drop microextraction (SDME) alone, resulting in a dramatic increase in the extraction efficiency. To protect the organic solvent and enhance the analyte distribution coefficient between the film and the vapor phase, a cooling system was applied. The proposed design was effective due to condensing the target analyte only on the uniform cooled thin film and not on the other regions in the extraction chamber. A corona discharge ionization source-ion mobility spectrometer was employed to identify the analyte. After optimizing the effective parameters, the limits of quantification (S/N = 10) and detection (S/N = 3) were calculated 0.1 and 0.03 µg L-1, respectively, and the dynamic range was measured between 0.1 and 7.0 µg L-1, with a determination coefficient of 0.9997. For three concentration levels of 0.1, 3.0, and 7.0 µg L-1, the relative standard deviations (n = 3) as the repeatability index were to be 6 %, 5 %, and 4 % for intra-day and 9 %, 6 %, and 5 % for inter-day, respectively. The enrichment factor was also calculated to be 3630 for the analyte concentration of 1.0 µg L-1. Well water, potato, and agricultural wastewater were analyzed as the real samples and the relative recovery values were measured between 92 % and 99 %. The accuracy of the proposed technique was validated by the European Standards EN 12393 method. In this approach, two steps of analyte extraction (DLLME and TFME) were used consecutively, resulting in better preconcentration and reduced matrix interference during cleaning-up.

A closer look at how the dispersive liquid-liquid microextraction method works. Investigation of the effect of solvent mixture composition on the quality and stability of the cloudy state.

The dispersive liquid-liquid microextraction (DLLME) is one of the most popular miniaturized extraction procedures. In this paper, the degree of dispersion and dispersion stability were studied with the aim to assess the correlations of these parameters with efficiency for the selected analytical application. The dependence between the degree of dispersion (cloudy state quality) and its stability obtained by various emulsification procedures, such as solvent-assisted emulsification (using various dispersive solvents) and mechanical emulsification (using auxiliary energies), is investigated and discussed. It was found out that the degree of dispersion depends on the type of emulsification procedure and decreases in the series: solvent-assisted (SA-) = ultrasound-assisted (UA-) > air-assisted (AA-) > vortex-assisted (VA-) emulsification. The emulsion stability depends on the degree of dispersion and there were 1810 and 2070 s for the most effective emulsification procedures, such us solvent-assisted and ultrasound-assisted emulsification, respectively. A comparison between the sensitivity of the analytical methods (using spectrophotometric determination of the anionic surfactants) and the degree of dispersion have been made. The sensitivity of the methods was ranked as follows: DLLME > UA-LLME > VA-LLME > AA-LLME.

Microsyringe-based slug-flow microextraction for rapid and accurate determination of antibiotics in highly saline seawater.

BACKGROUND: Extensive use of antibiotics leads to widespread environmental pollution, endangering ecosystems, and human health. It is particularly concerning, posing global threats requiring urgent attention and action. In this regard, the shift to mass spectrometry in determining antibiotics is highly desirable. Significant progress has been made in analyzing and optimizing the sensitivity of high-salt samples. However, the persistence of cumbersome operational procedures presents a significant challenge to this shift. Thus, the persistence of complex operational procedures needs to be addressed. RESULTS: In this study, a rapid and direct method for determining antibiotics in highly saline environmental water samples using microsyringe-based slug-flow microextraction (MSFME)-droplet spray ionization (DSI) mass spectrometry (MS) has been described. The proposed method successfully detected clarithromycin, ofloxacin, and sulfadimidine in seawater within a linear range of 1-1200 ng mL-1, with low limits of detection of 0.19 ng mL-1, 0.17 ng mL-1, and 0.20 ng mL-1, respectively (Signal/Noise = 3). Additionally, spiked real seawater samples of all three antibiotics demonstrated satisfactory recoveries (95.1-107.5%) and precision (RSD≤8.8%). The MSFME-treated high-salt sample (3.5 wt%) showed a mass spectral response intensity 4-5 orders of magnitude higher than the untreated medium-salt sample (0.35 wt%). Furthermore, exploration of the applicability of MSFME showed that it is suitable not only for high-salinity (3.5 wt%) samples but also for salt-free or low-salt and hard water samples rich in calcium and magnesium ions. SIGNIFICANCE: Comparisons with other methods, complex laboratory setups for sample processing are now simplified to a single step, completing the entire process, including desalination and detection, MSFME-DSI-MS provides faster results in less than 1 min while maintaining sensitivity comparable to that of other detection methods. In conclusion, this advancement provides an exceptionally simplified protocol for the rapid, highly sensitive, and quantitative determination of antibiotics in environmental water samples.

In-syringe homogeneous liquid-phase microextraction followed by filtration-based phase separation for on-site extraction of chloroanilines from water samples.

This study introduces a new in-syringe homogeneous liquid-phase microextraction method for the rapid on-site extraction of chloroanilines from water samples. Extraction was performed using a plastic syringe, eliminating the use of any electrical power source. Di-(2-ethylhexyl) phosphoric acid (DEHPA) served as the extractant. The process initially involved dissolving DEHPA in an alkaline solution to obtain a homogeneous solution. Subsequently, the sodium salt of DEHPA was precipitated by salting-out, and the resulting heterogeneous mixture was filtered using a syringe filter. The precipitate containing the analytes was then dissolved in methanol for analysis by high-performance liquid chromatography. Under optimal conditions, extraction recovery for chloroanilines ranged from 26% to 71%. Method linearity was evaluated within a concentration range of 1.0-100 µg/L, resulting in coefficients of determination exceeding 0.9987 for all analytes. Method detection limits ranged from 0.28 to 0.41 µg/L. Intra and inter-day precision values were below 9.5% and 10.8%, respectively. The developed method was applied to determine chloroanilines in real waters, yielding acceptable recoveries ranging from 80% to 109% for spiked tap, rain, and stream waters. Additionally, the method was successfully employed for on-site extraction of target contaminants, demonstrating no statistically significant differences compared to laboratory results.

Investigation of use of hydrophilic/hydrophobic NADESs for selective extraction of As(III) and Sb(III) ions in vegetable samples: Air assisted liquid phase microextraction and chemometric optimization.

In this paper, a green, cost-effective sample preparation method based on air assisted liquid phase microextraction (AA-LPME) was developed for the simultaneous extraction of As(III) and Sb(III) ions from vegetable samples using hydrophilic/hydrophobic natural deep eutectic solvents (NADESs). Central composite design was used for the optimization of extraction factors including NADES volume, extraction cycle, pH, and curcumin concentration. Limits of detection for As(III) and Sb(III) were 1.5 ng L-1 and 0.06 ng L-1, respectively. Working ranges for As(III) and Sb(III) were 0.2-300 ng L-1 (coefficient of determination (R2 = 0.9978) and 5-400 ng L-1 (R2 = 0.9996), respectively. Relative standard deviations for As(III) and Sb(III) were 2.2-2.8% and 2.9-3.2%, respectively. Enrichment factor of the method was 184 for As(III) and 172 for Sb(III). The accuracy and precision of the AA-NADES-LPME method were investigated by intraday/interday studies and standard reference material analysis, respectively. Finally, the AA-NADES-LPME method was successfully applied to microwave digested vegetable samples using the standard addition approach and acceptable recoveries were achieved.

The usability of green deep eutectic solvents in hollow fiber Liquid-Phase microextraction for the simultaneous extraction of analytes of different Natures: A comprehensive study.

In the current study, a wide range of deep eutectic solvents (DESs) with different properties (hydrophilic, hydrophobic, ionic, and nonionic) were prepared in the initial phase. Subsequently, an assessment was conducted to evaluate some characteristics of the produced DESs, including their stability at room temperature and their capacity to extract three distinct types of analytes (anionic, cationic, and non-ionic) simultaneously through hollow fiber-liquid phase microextraction (HF-LPME) technique. To carry out the extraction procedure, the prepared DESs were inserted into the pores (as supported liquid membrane (SLM)) and lumen of hollow fiber membrane (HF) to apply two-phase and three-phase HF-LPME techniques. After a thorough evaluation, the three-phase HF-LPME technique (HF(3)-LPME) was chosen by using a mixture of menthol/TBAB-based hydrophobic DES (DES-35) as SLM and the mixture of malic acid/citric acid/water-based hydrophilic DES (DES-2) as an extraction solvent in the lumen of HF. All factors affecting the extraction recovery (including pH, extraction time, extraction temperature, stirring speed, and salt effect) were optimized utilizing the one-variable-at-a-time (OVAT) methodology. After applying the extraction procedure, all extracted samples were analyzed using the UV-Vis spectrometer and results were recorded at different wavelengths including 655 nm for Methylene blue, 550 nm for Amaranth, and 375 nm for Quercetin. The calibration graphs showed linearity in the range of 20.0-1500 µg/L, with a limit of detection of 6.2-15.1 µg/L and correlation coefficients higher than 0.9913 for the studied analytes. Moreover, the intra-day RSD, inter-day RSD, preconcentration factor (PF), enrichment factors (EF), and extraction recoveries (ER%) were obtained in the range of 3.1-4.8, 3.8-6.7, 125, 102.9-111.4, and 82.3-89.1 %, respectively. The use of the selected DES in the HF-LPME methodology resulted in an ecologically friendly strategy, as evidenced by the use of green metrics from the SPMS tool. The proposed strategy is also considered environmentally friendly due to its use of minimal solvents, waste reduction, and low energy consumption. The proposed technique effectively and simultaneously extractedmethylene blue, amaranth, and quercetin analytes in different real samples.

Development of a new continuous homogenous liquid phase microextraction procedure based on in-situ preparation of deep eutectic solvent; application in the analysis of aliphatic amines in urine samples by GC-MS.

In the present work, a new microextraction procedure combined with gas chromatography-mass spectrometry has been developed for the analysis of several aliphatic amines from urine sample. The sample preparation method was a continuous homogenous liquid phase microextraction that was based on in-situ preparation of 4-chlorophenol: choline chloride deep eutectic solvent. The deep eutectic solvent was prepared by passing the mixture of related compounds through a syringe barrel filled with exothermic salts (calcium chloride and potassium bromide). The released heat by dissolving the salts and increasing the solution ionic strength assists the formation of the deep eutectic solvent. The influence of various factors on the efficiency of the proposed procedure including salts amount, flow rate, pH, salting-out effect, and extraction solvent volume was studied. The calibration curves were linear broadly over the concentration range of 1.2-250 ng mL-1 with coefficient of determinations ≥0.996. The enrichment factors were in the range of 188-246 and the limits of detection and quantification were 0.16-0.37 and 0.56-1.2 ng mL-1, respectively. Based on the results, the offered method was sensitive, rapid, eco-friendly, and efficient for extracting and determining aliphatic amines in urine samples.

Determination of phenytoin at trace levels in domestic wastewater and synthetic urine samples by gas chromatography-mass spectrometry after its preconcentration by simple liquid-phase microextraction.

This work presents a sensitive and accurate analytical method for the determination of phenytoin at trace levels in domestic wastewater and synthetic urine samples by gas chromatography-mass spectrometry (GC-MS) after the metal sieve-linked double syringe liquid-phase microextraction (MSLDS-LPME) method. A metal sieve was produced in our laboratory in order to disperse water-immiscible extraction solvents into aqueous media. Univariate optimization studies for the selection of proper extraction solvent, extraction solvent volume, mixing cycle, and initial sample volume were carried out. Under the optimum MSLDS-LPME conditions, mass-based dynamic range, limit of quantitation (LOQ), limit of detection (LOD), and percent relative standard deviation (%RSD) for the lowest concentration in calibration plot were figured out to be 100.5-10964.2 µg kg-1, 150.6 µg kg-1, 45.2 µg kg-1, and 9.4%, respectively. Detection power was improved as 187.7-folds by the developed MSLDS-LPME-GC-MS system while enhancement in calibration sensitivity was recorded as 188.0-folds. In the final step of this study, the accuracy and applicability of the proposed system were tested by matrix matching calibration strategy. Percent recovery results for domestic wastewater and synthetic urine samples were calculated as 95.6-110.3% and 91.7-106.6%, respectively. These results proved the accuracy and applicability of the proposed preconcentration method, and the obtained analytical results showed the efficiency of the lab-made metal sieve apparatus.

Spectrophotometric determination of phenol impurity in phenoxyethanol and phenol index of drinking water and municipal wastewater effluent after salting-out assisted liquid phase microextraction (SA-LPME).

In this study, a novel and convenient analytical method based on salting-out-assisted liquid phase microextraction (SA-LPME) has been developed. A spectrophotometric technique was employed to quantify the concentration of phenol in drinking water and treated wastewater, as well as the phenol impurity in 2-phenoxyethanol (PE). To accomplish this, a solution containing dissolved PE was supplemented with 4-aminoantipyrine (4-AAP) and hexacyanoferrate. Subsequently, NaCl was added to induce the formation of a two-phase system, consisting of fine droplets of PE as an extractant phase in the aqueous phase. The resulting red derivative was then extracted into the extractant phase and separated through centrifugation. Finally, the absorbance of the extracted derivative was measured at 520 nm. The Response Surface Methodology (RSM) based on the Box-Behnken Design (BBD) was employed to optimize the influential factors, namely 4-Aminoantipyrine (4-AAP), buffer (pH = 10), hexacyanoferrate, and NaCl. By utilizing the optimal conditions (buffer: 50 µL, 4-AAP (1% w/v): 80 µL, hexacyanoferrate (10% w/v): 65 µL, and NaCl: 0.7 g per 10 mL of the sample), the limit of detection was determined to be 0.7 ng mL-1 and 0.22 µg g-1 for water and PE samples, respectively. The relative standard deviation (RSD) and correlation of determination (r2) obtained fell within the range of 2.4-6.8% and 0.9983-0.9994, respectively. Moreover, an enrichment factor of 65 was achieved for a sample volume of 10 mL. The phenol concentration in two PE samples (PE-1, PE-2), provided by a pharmaceutical company (Pars Sadra Fanavar, Iran), were determined to be 0.83 ± 0.05 µg g-1 and 2.70 ± 0.14 µg g-1, respectively. Additionally, the phenol index in drinking water and treated municipal wastewater was found to be 3.60 ± 1.06 ng mL-1 and 4.60 ± 1.17 ng mL-1, respectively. These mentioned samples were spiked in order to evaluate the potential influence of the matrix. The relative recoveries from PE-1, PE-2 samples, drinking water, and treated municipal wastewater samples were measured as 104.5%, 97.5%, 101.6%, and 107.8%, respectively, indicating no matrix effect.

One-step online analysis of antibiotics in highly saline seawater by nano-based slug-flow microextraction.

The transition to mass spectrometry (MS) in the analysis of antibiotics in the marine environment is highly desirable, particularly in the enhancement of sensitivity for high-salinity (3.5 wt%) seawater samples. However, the persistence of complex operational procedures poses substantial challenges to this transition. In this study, a rapid method for the online analysis of antibiotics in seawater samples via nano-electrospray ionization (nESI) MS based on slug-flow microextraction (SFME) has been proposed. Comparisons with other methods, complex laboratory setups for sample processing are now seamlessly integrated into a single online step, completing the entire process, including desalination and detection, SFME-nESI-MS provides faster results in less than 2 min while maintaining sensitivity comparable to that of other detection methods. Using SFME-nESI, six antibiotics in high-salinity (3.5 wt%) seawater samples have been determined in both positive and negative ion modes. The proposed method successfully detected clarithromycin, ofloxacin, and sulfadimidine in seawater within a linear range of 1-1000 ng mL-1 and limit of detection (LOD) of 0.23, 0.06, and 0.28 ng mL-1, respectively. The method recovery was from 92.8% to 107.3%, and the relative standard deviation was less than 7.5%. In addition, the response intensity of SFME-nESI-treated high-salinity (3.5 wt%) samples surpassed that of untreated medium-salinity (0.35 wt%) samples by two to five orders of magnitude. This advancement provides an exceptionally simplified protocol for the online rapid, highly sensitive, and quantitative determination of antibiotics in high-salinity (3.5 wt%) seawater.

Development of a hollow fiber-liquid phase microextraction method using tissue culture oil for the extraction of free metoprolol from plasma samples.

In this research, a method known as a hollow fiber-liquid-phase microextraction was employed to extract and concentrate free metoprolol from plasma samples. The extracted analyte was subsequently determined using high-performance liquid chromatography coupled with a diode-array detector. Several parameters, including hollow fiber length, sonication time, extraction temperature, and salt addition, were investigated and optimized to enhance extraction efficiency. After extracting the analyte under optimum conditions from plasma samples, the enrichment factor and extraction recovery were 50 and 86 %, respectively. Moreover, the method exhibited detection and quantification limits of 0.41 and 1.30 ng mL-1, respectively. The analysis of real samples demonstrated satisfactory relative recoveries in the range of 91-99 %.

Deep eutectic solvent-based ferrofluid for highly efficient preconcentration and determination of metronidazole by vortex-assisted liquid-phase microextraction under experimental design optimization.

To determine metronidazole in water samples, we developed an environmentally friendly, efficient, and straightforward ferrofluid-based liquid-liquid microextraction sample pretreatment technique. It is coupled with a high-performance liquid chromatography-ultraviolet analytical technique known for its sensitivity, speed, and precision. The magnetic separation of metronidazole-containing ferrofluid from the matrix was effortlessly achieved through the application of an external magnetic field, eliminating the need for centrifugation. Response surface optimization was employed to systematically determine the key experimental parameters influencing extraction efficiency, including pH, NaCl concentration, ferrofluid volume, and vortex duration. With a low detection limit (0.116 ng mL-1), a broad linear range between 0.5 and 700 ng mL-1 was achieved at optimal conditions. Additionally, acceptable spiking recoveries (94.3-97.3 %) and RSD values (≤3.7 %) for intra- and inter-day precision were attained in water samples. In conclusion, the effectiveness of the vortex and ferrofluid combination, along with the convenience of collection and elimination of the need for centrifugation, bestows a highly valuable technique for determining metronidazole in water samples.

Comparison of the applicability of electromembrane extraction and liquid-phase microextraction for extraction of non-polar basic drugs from different biological samples: Using clozapine as the model analyte.

Understanding and comparing the applicability of electromembrane extraction (EME) and liquid-phase microextraction (LPME) is crucial for selecting an appropriate microextraction approach. In this work, EME and LPME based on supported liquid membranes were compared using biological samples, including whole blood, urine, saliva, and liver tissue. After optimization, efficient EME and LPME of clozapine from four biological samples were achieved. EME provided higher recovery and faster mass transfer for blood and liver tissue than LPME. These advantages were attributed to the electric field disrupting clozapine binding to interfering substances. For urine and saliva, EME demonstrated similar recoveries while achieving faster mass transfer rates. Finally, efficient EME and LPME were validated and evaluated combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS). The coefficient of determination of all methods was greater than 0.999, and all methods showed acceptable reproducibility (≤14%), accuracy (90%-110%), and matrix effect (85%-112%). For liver and blood with high viscosity and complex matrices, EME-LC-MS/MS provided better sensitivity than LPME-LC-MS/MS. The above results indicated that both EME and LPME could be used to isolate non-polar basic drugs from different biological samples, although EME demonstrated higher recovery rates for liver tissue and blood.