Sensitive visual detection of norfloxacin in water by smartphone assisted colorimetric method based on peroxidase-like active cobalt-doped Fe3O4 nanozyme.

Norfloxacin is widely used owing to its strong bactericidal effect on Gram-negative bacteria. However, the residual norfloxacin in the environment can be biomagnified via food chain and may damage the human liver and delay the bone development of minors. Present work described a reliable and sensitive smartphone colorimetric sensing system based on cobalt-doped Fe3O4 magnetic nanoparticles (Co-Fe3O4 MNPs) for the visual detection of norfloxacin. Compared with Fe3O4, Co-Fe3O4 MNPs earned more remarkably peroxidase-like activity and TMB (colorless) was rapidly oxidized to oxTMB (blue) with the presence of H2O2. Interestingly, the addition of low concentration of norfloxacin can accelerate the color reaction process of TMB, and blue deepening of the solution can be observed with the naked eye. However, after adding high concentration of norfloxacin, the activity of nanozyme was inhibited, resulting in the gradual fading of the solution. Based on this principle, a colorimetric sensor integrated with smartphone RGB mode was established. The visual sensor exhibited good linearity for norfloxacin monitoring in the range of 0.13-2.51 µmol/L and 17.5-100 µmol/L. The limit of visual detection was 0.08 µmol/L. In the actual water sample analysis, the spiked recoveries of norfloxacin were over the range of 95.7%-104.7 %. These results demonstrated that the visual sensor was a convenient and fast method for the efficient and accurate detection of norfloxacin in water, which may have broad application prospect.

Efficient magnetic capture of PE microplastic from water by PEG modified Fe3O4 nanoparticles: Performance, kinetics, isotherms and influence factors.

Due to their resistance to degradation, wide distribution, easy diffusion and potential uptake by organisms, microplastics (MPs) pollution has become a major environmental concern. In this study, PEG-modified Fe3O4 magnetic nanoparticles demonstrated superior adsorption efficiency against polyethylene (PE) microspheres compared to other adsorbents (bare Fe3O4, PEI/Fe3O4 and CA/Fe3O4). The maximum adsorption capacity of PE was found to be 2203 mg/g by adsorption isotherm analysis. PEG/Fe3O4 maintained a high adsorption capacity even at low temperature (5°C, 2163 mg/g), while neutral pH was favorable for MP adsorption. The presence of anions (Cl-, SO42-, HCO3-, NO3-) and of humic acids inhibited the adsorption of MPs. It is proposed that the adsorption process was mainly driven by intermolecular hydrogen bonding. Overall, the study demonstrated that PEG/Fe3O4 can potentially be used as an efficient control against MPs, thus improving the quality of the aquatic environment and of our water resources.

Design of the distribution of iron oxide (Fe3O4) nano-particle drug in realistic cholangiocarcinoma model and the simulation of temperature increase during magnetic induction hyperthermia.

The prognosis for Cholangiocarcinoma (CCA) is unfavorable, necessitating the development of new therapeutic approach such as magnetic hyperthermia therapy (MHT) which is induced by magnetic nano-particle (MNPs) drug to bridge the treatment gap. Given the deep location of CCA within the abdominal cavity and proximity to vital organs, accurately predict the individualized treatment effects and safety brought by the distribution of MNPs in tumor will be crucial for the advancement of MHT in CCA. The Mimics software was used in this study to conduct three-dimensional reconstruction of abdominal computed tomography (CT) and magnetic reso-nance imaging images from clinical patients, resulting in the generation of a realistic digital geometric model representing the human biliary tract and its adjacent structures. Subsequently, The COMSOL Multiphysics software was utilized for modeling CCA and calculating the heat transfer law resulting from the multi-regional distribution of MNPs in CCA. The temperature within the central region of irregular CCA measured approximately 46°C, and most areas within the tumor displayed temperatures surpassing 41°C. The temperature of the inner edge of CCA is only 39 ∼ 41℃, however, it can be ameliorated by adjusting the local drug concentration through simulation system. For CCA with diverse morphologies and anatomical locations, the multi-regional distribution patterns of intratumoral MNPs and a slight overlap of drug distribution areas synergistically enhance intratumoral temperature while ensuring treatment safety. The present study highlights the practicality and imperative of incorporating personalized intratumoral MNPs distribution strategy into clinical practice for MHT, which can be achieved through the development of an integrated simulation system which incorporates medical image data and numerical calculations.

Anti-microbial, anti-biofilm, and efflux pump inhibitory effects of ellagic acid-bonded magnetic nanoparticles against Escherichia coli isolates.

The spread of microbial resistance is a threat to public health. In this study, the anti-microbial, anti-biofilm, and efflux pump inhibitory effects of ellagic acid-loaded magnetic nanoparticles (Fe3O4NPs@EA) against beta-lactamase producing Escherichia coli isolates have been investigated. The effects of Fe3O4 NPs@EA on the growth inhibition of E. coli isolates were determined by disc diffusion method and determining the minimum inhibitory concentration was done using broth micro-dilution method. The anti-biofilm effect of nanoparticles was investigated using the microplate method. The efflux pump inhibitory effect of nanoparticles was investigated using cart-wheel method and by investigating the effect of nanoparticles on acrB and tolC genes expression levels. Fe3O4 NPs@EA showed anti-bacterial effects against test bacteria, and the MIC of these nanoparticles varied from 0.19 to 1.56 mg/mL. These nanoparticles caused a 43-62% reduction in biofilm formation of test bacteria compared to control. Furthermore, efflux pump inhibitory effect of these nanoparticles was confirmed at a concentration of 1/8 MIC, and the expression of acrB and tolC genes decreased in bacteria treated with 1/4 MIC Fe3O4 NPs@EA. According to the results, the use of nanoparticles containing ellagic acid can provide a basis for the development of new treatments against drug-resistant E. coli. This substance may improve the concentration of antibiotics in the bacterial cell and increase their effectiveness by inhibiting the efflux in E. coli isolates.

Albumin incorporation into recognising layer of HER2-specific magnetic nanoparticles as a tool for optimal targeting of the acidic tumor microenvironment.

Cancer is unquestionably a global healthcare challenge, spurring the exporation of novel treatment approaches. In recent years, nanomaterials have garnered significant interest with the greatest hopes for targeted nanoformulations due to their cell-specific delivery, improved therapeutic efficacy, and reduced systemic toxicity for the organism. The problem of successful clinical translation of nanoparticles may be related to the fact that most in vitro tests are performed at pH values of normal cells and tissues, ranging from 7.2 to 7.4. The extracellular pH values of tumors are characterized by a shift to a more acidic region in the range of 5.6-7.0 and represent a crucial target for enhancing nanoparticle delivery to cancer cells. Here we show the method of non-active protein incorporation into the surface of HER2-targeted nanoparticles to achieve optimal cellular uptake within the pH range of the tumor microenvironment. The method efficacy was confirmed in vitro and in vivo showing the maximum binding of nanoparticles to cells at a pH value 6.4. Namely, fluorescent magnetic nanoparticles, modified with HER2-recognising affibody ZHER2:342, with proven specificity in terms of HER2 recognition (with 62-fold higher cellular uptake compared to control nanoparticles) were designed for targeting cancer cells at slightly acidic pH values. The stabilizing protein, namely, bovine serum albumin, one of the major blood components with widespread availability and biocompatibility, was used for the decoration of the nanoparticle surface to alter the pH response of the targeting magnetic conjugates. The optimally designed nanoparticles showed a bell-shaped dependency of interaction with cancer cells in the pH range of 5.6-8.0 with maximum cellular uptake at pH value 6.4 close to that of the tumor microenvironment. In vivo experiments revealed that after i.v. administration, BSA-decorated nanoparticles exhibited 2 times higher accumulation in tumors compared to magnetic nanoparticles modified with affibody only. Thus, we demonstrated a valid method for enhancing the specificity of targeted nanoparticle delivery to cancer cells without changing the functional components of nanoparticles.

Development of Magnetic Nanosystems with Potential for the Treatment of Inner Ear Pathologies.

Hearing loss (HL) affects more than 5% of the global population, with projections indicating an impact of up to 50% on young individuals in the next years. HL treatments remain limited due to the inner ear's hermeticism. HL often involves inflammatory processes, underscoring the need for enhanced delivery of antiinflammatory agents to the inner ear. Our research focuses on the development of a directed therapy based on magnetic nanoparticles (MNPs). We previously synthesized biocompatible folic acid-coated iron oxide-core nanoparticles (MNPs@FA) as potential carriers for the anti-inflammatory Diclofenac (Dfc). This study aims to incorporate Dfc onto MNPs@FA to facilitate targeted drug delivery to the inner ear. Through optimizing the loading procedure, we achieved optimal loading capacity. Dfc release was studied in the simulated target fluid and the administration vehicle. Complete characterization is also shown. In vitro biocompatibility testing ensured the biosafety of the resulting formulation. Subsequent ex vivo targeting assays on murine cochleae validated the nanosystems' ability to penetrate the round window membrane, one of the main HL therapy barriers. These findings serve as validation before continuing to more complex in vivo studies. Together, the data here presented represent an advancement in addressing unmet medical needs in HL therapy.

A comparative study of sericin and gluten for magnetic nanoparticle-mediated drug delivery to breast cancer cell lines.

With breast cancer emerging as a pressing global health challenge, characterized by escalating incidence rates and geographical disparities, there is a critical need for innovative therapeutic strategies. This comprehensive research navigates the landscape of nanomedicine, specifically focusing on the potential of magnetic nanoparticles (MNPs), with magnetite (Fe3O4) taking center stage. MNPs, encapsulated in biocompatible polymers like silica known as magnetic silica nanoparticles (MSN), are augmented with phosphotungstate (PTA) for enhanced chemodynamic therapy (CDT). PTA is recognized for its dual role as a natural chelator and electron shuttle, expediting electron transfer from ferric (Fe3+) to ferrous (Fe2+) ions within nanoparticles. Additionally, protein-based charge-reversal nanocarriers like silk sericin and gluten are introduced to encapsulate (MSN-PTA) nanoparticles, offering a dynamic facet to drug delivery systems for potential revolutionization of breast cancer therapy. This study successfully formulates and characterizes protein-coated nanocapsules, specifically MSN-PTA-SER, and MSN-PTA-GLU, with optimal physicochemical attributes for drug delivery applications. The careful optimization of sericin and gluten concentrations results in finely tuned nanoparticles, showcasing uniform size, enhanced negative zeta potential, and remarkable stability. Various analyses, from Dynamic Light Scattering (DLS) and scanning electron microscopy (SEM) to transmission electron microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), X-Ray diffraction analysis (XRD), and Thermogravimetric analysis (TGA), provide insights into structural integrity and surface modifications. Vibrating Sample Magnetometer (VSM) analysis underscores superparamagnetic behavior, positioning these nanocapsules as promising candidates for targeted drug delivery. In vitro evaluations demonstrate dose-dependent inhibition of cell viability in MCF-7 and Zr-75-1 breast cancer cells, emphasizing the therapeutic potential of MSN-PTA-SER and MSN-PTA-GLU. The interplay of surface charge and pH-dependent cellular uptake highlights the robust stability and versatility of these nanocarriers in tumor microenvironment, paving the way for advancements in targeted drug delivery and personalized nanomedicine. This comparative analysis explores the suitability of silk sericin and gluten, unraveling a promising avenue for the development of advanced, targeted, and efficient breast cancer treatments.

DNA nanosensor based on bipedal 3D DNA walker-driven proximal catalytic hairpin assembly for sensitive and fast TK1 mRNA detection.

Hyperproliferative  diseases are the first step for tumor formation; thymidine kinase 1 (TK1) mRNA is closely related to cell proliferation. Therefore, the risk of malignant proliferation can be identified by sensitively detecting the variance in TK1 mRNA concentration, which can be used for tumor auxiliary diagnosis and monitoring tumor treatment. Owing to the low abundance and instability of TK1 mRNA in real samples, the development of a sensitive and fast mRNA detection method is necessary. A DNA nanosensor that can be used for detecting TK1 mRNA based on bipedal 3D DNA walker-driven proximal catalytic hairpin assembly (P-CHA) was developed. P-CHA hairpins were hybridized to a linker DNA strand coupled with magnetic nanoparticles to increase their local concentrations. The bipedal DNA walking on the surface of NPs accelerates reaction kinetics using the proximity effect. Taking advantage of the signal amplification of P-CHA as well as the rapid reaction rate of the DNA walker in 80 min, the proposed sensor detects TK1 mRNA with a low detection limit of 14 pM and may then be applied to clinical diagnosis.

Chitosan decorated magnetic nanobiocatalyst of Bacillus derived α-amylase as a role model for starchy wastewater treatment, detergent additive and textile desizer.

In this study, Bacillus tequilensis TB5 α-amylase from rice-milled by-products (rice bran and de-oiled rice bran) was successfully immobilized onto biologically synthesized magnetic nanoparticles fabricated with chitosan (MNP-Ch) and characterized via different biophysical techniques. Furthermore, the study emphasized incorporating this nanostructure framework (MNP@2mgchitosan_DORB-amy and MNP@3mgchitosan_RB-amy) to offer diverse applications, including enzymatic desizing, cleaning starchy stains, and treating synthetic starchy wastewater. An enzyme loading of > 90 % for both enzymes indicated increased binding sites due to the functional moieties of chitosan on the MNP. The Km was 0.28 and 0.31 mg/mL for the immobilized and free forms of DORB-amy, respectively, and 0.18 and 0.27 mg/mL for the immobilized and free forms of RB-amy, respectively. A low Km indicated an increased affinity of MNP-Ch-immobilized forms of enzymes toward the substrate. The performance of both immobilized enzymes improved at a wide range of pH and temperature, which may be attributed to the covalent binding of the enzyme on to the MNP-Ch. The nanobiocatalysts in the detergent act synergistically to fade the starchy stains. Furthermore, an 8-9 TEGEWA scale rating with > 11 % of starch removal was obtained through the biodesizing of starch-sized cotton fabric. The nanobiocatalyst efficiently decomposed starch and liberated 650-670 mg/L of reducing sugar from the synthetic wastewater, therefore offering promising opportunities for its exploration in a wastewater treatment plant. Thus, the study recommends the potential exploration of sturdy matrices like MNP to offer remarkable applications with maximum operational stability, easier recovery, and higher efficiency.

Isothermal Amplification Using Temperature-Controlled Frequency Mixing Magnetic Detection-Based Portable Field-Testing Platform.

Sensitive magnetic nucleic acid (NA) detection via frequency mixing magnetic detection (FMMD) requires amplified NA samples for which a reliable temperature control is necessary. The feasibility of recombinase polymerase amplification (RPA) was studied within a newly integrated temperature-controlled sensor unit of a mobile FMMD based setup. It has been demonstrated that the inherently generated heat of the low frequency (LF) excitation signal of FMMD can be utilized and controlled by means of pulse width modulation (PWM). To test control performance in a point of care (PoC) setting with changing ambient conditions, a steady state and dynamic response model for the thermal behavior at the sample position of the sensor were developed. We confirmed that in the sensor unit of the FMMD device, RPA performs similar as in a temperature-controlled water bath. For narrow steady state temperature regions, a linear extrapolation suffices for estimation of the sample position temperature, based on the temperature feedback sensor for PWM control. For any other ambient conditions, we identified and validated a lumped parameter model (LPM) performing with high estimation accuracy. We expect that the method can be used for NA amplification and magnetic detection using FMMD in resource-limited settings.

Smart nanocarriers for enzyme-activated prodrug therapy.

Exogenous enzyme-activated prodrug therapy (EPT) is a potential cancer treatment strategy that delivers non-human enzymes into or on the surface of the cell and subsequently converts a non-toxic prodrug into an active cytotoxic substance at a specific location and time. The development of several pharmacological pairs based on EPT has been the focus of anticancer research for more than three decades. Numerous of these pharmacological pairs have progressed to clinical trials, and a few have achieved application in specific cancer therapies. The current review highlights the potential of enzyme-activated prodrug therapy as a promising anticancer treatment. Different microbial, plant, or viral enzymes and their corresponding prodrugs that advanced to clinical trials have been listed. Additionally, we discuss new trends in the field of enzyme-activated prodrug nanocarriers, including nanobubbles combined with ultrasound (NB/US), mesoscopic-sized polyion complex vesicles (PICsomes), nanoparticles, and extracellular vesicles (EVs), with special emphasis on smart stimuli-triggered drug release, hybrid nanocarriers, and the main application of nanotechnology in improving prodrugs.

Structure-Function Relationship of Iron Oxide Nanoflowers: Optimal Sizes for Magnetic Hyperthermia Depending on Alternating Magnetic Field Conditions.

Iron oxide nanoflowers (IONFs) that display singular magnetic properties can be synthesized through a polyol route first introduced almost 2 decades ago by Caruntu et al, presenting a multi-core morphology in which several grains (around 10 nm) are attached together and sintered. These outstanding properties are of great interest for magnetic field hyperthermia, which is considered as a promising therapy against cancer. Although of significantly smaller diameter, the specific adsorption rate (SAR) of IONFs reach values as large as for "magnetosomes" that are natural magnetic nanoparticles typically ~40 nm found in certain bacteria, which can be grown artificially but with much lower yield compared to chemical synthesis such as the polyol route. This work aims at better understanding the structure-property relationships, linking the internal IONF nanostructure as observed by HR-TEM to their magnetic properties. A library of mono- and multicore IONFs is presented, with diameters ranging from 11 to 30 nm in a narrow size distribution. More particularly, by relating their structural features to their magnetic properties investigated by utilizing AC magnetometry over a wide range of alternating magnetic field conditions, we showed that the SAR values of all synthesized batches vary with overall diameter and number of constituting cores.

Magnetic hybrid spheres of glauconite/calcium alginate interface for methylene blue adsorption: Synthesis, characterization, and novel physicochemical insights through theoretical treatment.

Fe3O4 nanoparticles were embedded within a glauconite­calcium alginate (G/CA) matrix to create magnetic hybrid spheres (MNPs-G/CA), with the aim of purifying water from methylene blue (MB) at temperatures of 25, 40, and 50 °C. MNPs-G/CA adsorbent was characterized using numerous techniques, including elemental mapping, zeta potential, FTIR, FESEM, XRD, EDX, and TEM. The greatest amount of the removed MB was achieved under definite conditions of solution pH 8.0, MNPs-G/CA mass (25 mg), interaction time (2 h), and 200 mg/L of MB concentration. The MB uptake process kinetic followed a pseudo-second-order equation (R2 > 0.99) at all tested temperatures. The equilibrium data were fitted to a statistical physics multilayer model in conjunction with the Langmuir and Freundlich equations. The steric n parameter reveals that MNPs-G/CA adsorbent possesses a mixed adsorption orientation (i.e., ranging from 0.69 to 0.93) across various temperatures. The amount of MNPs-G/CA active positions (the NM parameter) was progressively increased from 245 mg/g to 419 mg/g. The measured adsorption capacities (Qsat) ranged from 466.49 to 664.37 mg/g, and the removal of MB molecules was consistent with an endothermic interaction. The interface between the MNPs-G/CA-MB was principally dictated by electrostatic attractions, as evidenced by the values of adsorption energies (∆E), which varied from 16.75 to 21.52 kJ/mol. The regenerated MNPs-G/CA offered over 80 % of its adsorption strength after the fourth adsorption-desorption cycle. This study contributes to our understanding of the physicochemical parameters controlling the MB adsorption mechanism on multifunctional hybrid adsorbents, like the interface between glauconite, alginate, and MNPs.

Magnetic fibrin nanofiber hydrogel delivering iron oxide magnetic nanoparticles promotes peripheral nerve regeneration.

Peripheral nerve injury is a debilitating condition that have a profound impact on the overall quality of an individual's life. The repair of peripheral nerve defects continues to present significant challenges in the field. Iron oxide magnetic nanoparticles (IONPs) have been recognized as potent nanotools for promoting the regeneration of peripheral nerves due to their capability as biological carriers and their ability to template the hydrogel structure under an external magnetic field. This research used a fibrin nanofiber hydrogel loaded with IONPs (IONPs/fibrin) to promote the regeneration of peripheral nerves in rats. In vitro examination of PC12 cells on various concentrations of IONPs/fibrin hydrogels revealed a remarkable increase in NGF and VEGF expression at 2% IONPs concentration. The biocompatibility and degradation of 2% IONPs/fibrin hydrogel were assessed using the in vivo imaging system, demonstrating subcutaneous degradation within a week without immediate inflammation. Bridging a 10-mm sciatic nerve gap in Sprague Dawley rats with 2% IONPs/fibrin hydrogel led to satisfactory morphological recovery of myelinated nerve fibers. And motor functional recovery in the 2% IONPs/fibrin group was comparable to autografts at 6, 9 and 12 weeks postoperatively. Hence, the composite fibrin hydrogel incorporating 2% IONPs exhibits potential for peripheral nerve regeneration.

Development of Molecularly Imprinted Magnetic Amino Acid-Based Nanoparticles for Voltammetric Analysis of Lead Ions in Honey.

Lead (Pb) is a hazardous metal that poses a significant threat to both the environment and human health. The presence of Pb in food products such as honey can pose a significant risk to human health and is therefore important to detect and monitor. In this study, we propose a voltammetric detection method using molecularly imprinted polymer (MIP) electrodes to detect Pb (II) ions in honey. Pb (II) ion-imprinted amino acid-based nanoparticles with magnetic properties on a carbon paste electrode (MIP-CPE) were designed to have high sensitivity and selectivity towards Pb (II) ions in the honey sample. Zetasizer measurements, electron spin resonance, and scanning electron microscopy were used to characterize magnetic polymeric nanoparticles. The results showed that the voltammetric detection method using MIP-CPE was able to accurately detect Pb (II) ions in honey samples with a low detection limit. The proposed method offers a simple, rapid, cost-effective solution for detecting Pb (II) ions in honey. It could potentially be applied to other food products to ensure their safety for human consumption. The MIP-CPE sensor was designed to have high sensitivity and selectivity towards Pb (II) ions in the honey sample. The results showed that the technique was able to deliver highly sensitive results since seven different concentrations were prepared and detected to obtain an R2 of 0.9954, in addition to a low detection limit (LOD) of 0.0912 µM and a low quantification limit (LOQ) of 0.276 µM. Importantly, the analysis revealed no trace of Pb (II) ions in the honey samples obtained from Cyprus.

Initial therapeutic evidence of a borosilicate bioactive glass (BSG) and Fe3O4 magnetic nanoparticle scaffold on implant-associated Staphylococcal aureus bone infection.

Implant-associated Staphylococcus aureus (S. aureus) osteomyelitis is a severe challenge in orthopedics. While antibiotic-loaded bone cement is a standardized therapeutic approach for S. aureus osteomyelitis, it falls short in eradicating Staphylococcus abscess communities (SACs) and bacteria within osteocyte-lacuna canalicular network (OLCN) and repairing bone defects. To address limitations, we developed a borosilicate bioactive glass (BSG) combined with ferroferric oxide (Fe3O4) magnetic scaffold to enhance antibacterial efficacy and bone repair capabilities. We conducted comprehensive assessments of the osteoinductive, immunomodulatory, antibacterial properties, and thermal response of this scaffold, with or without an alternating magnetic field (AMF). Utilizing a well-established implant-related S. aureus tibial infection rabbit model, we evaluated its antibacterial performance in vivo. RNA transcriptome sequencing demonstrated that BSG + 5%Fe3O4 enhanced the immune response to bacteria and promoted osteogenic differentiation and mineralization of MSCs. Notably, BSG + 5%Fe3O4 upregulated gene expression of NOD-like receptor and TNF pathway in MSCs, alongside increased the expression of osteogenic factors (RUNX2, ALP and OCN) in vitro. Flow cytometry on macrophage exhibited a polarization effect towards M2, accompanied by upregulation of anti-inflammatory genes (TGF-ß1 and IL-1Ra) and downregulation of pro-inflammatory genes (IL-6 and IL-1ß) among macrophages. In vivo CT imaging revealed the absence of osteolysis and periosteal response in rabbits treated with BSG + 5%Fe3O4 + AMF at 42 days. Histological analysis indicated complete controls of SACs and bacteria within OLCN by day 42, along with new bone formation, signifying effective control of S. aureus osteomyelitis. Further investigations will focus on the in vivo biosafety and biological mechanism of this scaffold within infectious microenvironment.

Impact of Particle Size on the Nonlinear Magnetic Response of Iron Oxide Nanoparticles during Frequency Mixing Magnetic Detection.

Magnetic nanoparticles (MNPs), particularly iron oxide nanoparticles (IONPs), play a pivotal role in biomedical applications ranging from magnetic resonance imaging (MRI) enhancement and cancer hyperthermia treatments to biosensing. This study focuses on the synthesis, characterization, and application of IONPs with two different size distributions for frequency mixing magnetic detection (FMMD), a technique that leverages the nonlinear magnetization properties of MNPs for sensitive biosensing. IONPs are synthesized through thermal decomposition and subsequent growth steps. Our findings highlight the critical influence of IONP size on the FMMD signal, demonstrating that larger particles contribute dominantly to the FMMD signal. This research advances our understanding of IONP behavior, underscoring the importance of size in their application in advanced diagnostic tools.

Zinc/Magnesium Ferrite Nanoparticles Functionalized with Silver for Optimized Photocatalytic Removal of Malachite Green.

Water pollution is a major environmental challenge. Due to the inefficiency of conventional wastewater treatment plants in degrading many organic complex compounds, these recalcitrant pollutants end up in rivers, lakes, oceans and other bodies of water, affecting the environment and human health. Semiconductor photocatalysis is considered an efficient complement to conventional methods, and the use of various nanomaterials for this purpose has been widely explored, with a particular focus on improving their activity under visible light. This work focuses on developing magnetic and photoactive zinc/magnesium mixed ferrites (Zn0.5Mg0.5Fe2O4) by sol-gel and solvothermal synthesis methods, which are two of the most important and efficient methods used for the synthesis of ferrite nanoparticles. The nanoparticles (NPs) synthesized by the sol-gel method exhibited an average size of 14.7 nm, while those synthesized by the solvothermal method had an average size of 17.4 nm. Both types possessed a predominantly cubic structure and demonstrated superparamagnetic behavior, reaching a magnetization saturation value of 60.2 emu g-1. Due to the high recombination rate of electrons/holes, which is an intrinsic feature of ferrites, surface functionalization with silver was carried out to enhance charge separation. The results demonstrated a strong influence of adsorption and of the deposition of silver. Several optimization steps were performed during synthesis, allowing us to create efficient catalysts, as proved by the almost full removal of the dye malachite green attaining 95.0% (at a rate constant of 0.091 min-1) and 87.6% (at a rate constant of 0.017 min-1) using NPs obtained by the sol-gel and solvothermal methods, respectively. Adsorption in the dark accounted for 89.2% of the dye removal for nanoparticles prepared by sol-gel and 82.8% for the ones obtained by the solvothermal method. These results make mixed zinc/magnesium ferrites highly promising for potential industrial application in effluent photoremediation using visible light.

Magnetic engineering nanoparticles: Versatile tools revolutionizing biomedical applications.

The use of nanoparticles has increased significantly over the past few years in a number of fields, including diagnostics, biomedicine, environmental remediation, and water treatment, generating public interest. Among various types of nanoparticles, magnetic nanoparticles (MNPs) have emerged as an essential tool for biomedical applications due to their distinct physicochemical properties compared to other nanoparticles. This review article focuses on the recent growth of MNPs and comprehensively reviews the advantages, multifunctional approaches, biomedical applications, and latest research on MNPs employed in various biomedical techniques. Biomedical applications of MNPs hold on to their ability to rapidly switch magnetic states under an external field at room temperature. Ideally, these MNPs should be highly susceptible to magnetization when the field is applied and then lose that magnetization just as quickly once the field is removed. This unique property allows MNPs to generate heat when exposed to high-frequency magnetic fields, making them valuable tools in developing treatments for hyperthermia and other heat-related illnesses. This review underscores the role of MNPs as tools that hold immense promise in transforming various aspects of healthcare, from diagnostics and imaging to therapeutic treatments, with discussion on a wide range of peer-reviewed articles published on the subject. At the conclusion of this work, challenges and potential future advances of MNPs in the biomedical field are highlighted.

Numerical Simulation of Thermal Therapy for Melanoma in Mice.

In recent years, the progressively escalating incidence and exceptionally high fatality rate of cutaneous melanoma have drawn the attention of numerous scholars. Magnetic induction hyperthermia, as an efficacious tumor treatment modality, has been promoted and applied in the therapy of some tumors. In this paper, the melanoma atop the mice's heads was chosen as the research subject, and a magnetic induction hyperthermia approach based on Helmholtz coils as the magnetic field excitation was investigated and designed. The influence of the electromagnetic field and thermal field on organisms was addressed through modeling by COMSOL simulation software. The results showed that the maximum values of induced electric field and magnetic induction strength in mouse tumor tissues were 63.1 V/m and 8.5621 mT, respectively, which reached the threshold value of magnetic field strength required for magnetic induction hyperthermia. The maxima of the induced electric field and magnetic induction intensity in brain tissues are, respectively, 35.828 V/m and 8.57 mT. Approximately 93% of the tumor tissue can reach 42 °C, and the maximum temperature is 44.2 °C. Within this temperature range, a large quantity of tumor cells can be successfully induced to undergo apoptosis without harming normal cells, and the therapeutic effect is favorable.