Development towards a novel screening method for nipecotic acid bioisosteres using molecular imprinted polymers (MIPs) as alternative to in vitro cellular uptake assays.

Impaired expression of GABA transporters (GATs) is closely related to the pathogenesis of among others Parkinson's disease and epilepsy. As such, lipophilic nipecotic acid analogs have been extensively studied as GAT1-addressing drugs and radioligands but suffer from limited brain uptake due to the zwitterionic properties of the nipecotic acid moiety. Bioisosteric replacement of the carboxylic acid group is a promising strategy to improve the brain uptake, though it requires knowledge on the binding of these isosteres to GAT1. To screen nipecotic acid isosteres for their affinity to GAT1 in a time- and cost-effective manner, this research aims to develop a molecular imprinted polymer (MIP) that mimics the natural binding site of GAT1 and can act as an alternative screening tool to the current radiometric and mass spectrometry cellular-based assays. To this end, a nipecotic acid MIP was created using the electropolymerization of ortho-phenylenediamine (oPD) by cyclic voltammetry (CV). The optimization of the generated receptor layer was achieved by varying the scan rate (50-250 mV/s) and number of CV cycles (5-12), yielding an optimized MIP with an average imprinting factor of 2.6, a linear range of 1-1000 nm, and a theoretical LOD of 0.05 nm, as analyzed by electrical impedance spectroscopy (EIS). Selectivity studies facilitated the investigation of major binding interactions between the MIP and the substrate, building an experimental model that compares characteristics of various analogs. Results from this model indicate that the substrate carboxylic acid group plays a more important role in binding than an amine group, after comparing the binding of cyclohexanecarboxylic acid (average IF of 1.7) and piperidine (average IF of 0.46). The research culminates in a discussion regarding the feasibility of the in vitro model, comparing the synthetic system against the biological performance of GAT1. Thus, evaluating if it is possible to generate a synthetic GAT1 mimic, and if so, provide directions for follow-up research.

A Strep-tag Imprinted Polymer Platform for Heterogenous Bio(electro)catalysis.

Molecularly imprinted polymers (MIPs) are artificial receptors equipped with selective recognition sites for target molecules. One of the most promising-strategies for protein MIPs relies on the exploitation of short surface-exposed protein fragments, termed epitopes, as templates to imprint binding sites in a polymer scaffold for a desired protein. However, the lack of high-resolution structural data of flexible surface-exposed regions challenges the selection of suitable epitopes. Here, we addressed this drawback by developing a polyscopoletin-based MIP that recognizes recombinant proteins via the widely used Strep-tag II affinity peptide. Electrochemistry, surface-sensitive spectroscopy, and molecular dynamics simulations were employed to ensure an utmost control of the Strep-MIP electrosynthesis. The functionality of this novel platform was verified with two Strep-tag labeled enzymes: an O2-tolerant [NiFe]-hydrogenase, and an alkaline phosphatase. The enzymes preserved their biocatalytic activities after multiple utilization confirming the efficiency of Strep-MIP as a general biocompatible platform to confine recombinant proteins for exploitation in biotechnology.

Rapid and sensitive detection of etomidate based on functionalized copper nanoclusters fluorescent probe.

Etomidate as a non-barbiturate sedative, has central inhibitory effect and addiction and has been listed as a controlled drug in some countries due to the abusing trend nowadays. Therefore, rapid and sensitive detection of etomidate is of great significance. In this work, a novel fluorescent sensing probe (CuNCs@MIPs) based on copper nanoclusters (CuNCs) and molecular imprinted polymers (MIPs) has been firstly reported. CuNCs was environment-friendly synthesized using poly(vinylpyrrolidone) as a template and ascorbic acid as a reducing agent. After functionalized with molecular imprinting technique, the CuNCs@MIPs probe has special binding cavities on surface to target etomidate, causing the fluorescence intensity rapidly decrease, which confirmed it has excellent sensitivity, selectivity and stability. Under optimal conditions, the fluorescent sensing probe presented high precision linear relationship for etomidate in range of 10-500 ng/ml with detection limit of 10 ng/ml, and the whole detection process was completed within 10 min. This sensing method has also been applied to real samples detection, still demonstrated excellent feasibility in electronic cigarette liquids and urine. More importantly, compared with previous methods, this fluorescent sensing method has advantages such as rapid, simple and easy to operate. Collectively, the proposed CuNCs@MIPs sensing probe has good fluorescence characteristics and simple synthesis strategy, showed a great potential in etomidate detection and application.

Remote magnetically stimulated xanthan-biochar-Fe3O4-molecularly imprinted biopolymer hydrogel toward electrochemical enantioselection of l-tryptophan.

Monitoring the levels of L-Tryptophan (L-Trp) in body fluids is crucial due to its significant role in metabolism and protein synthesis, which ultimately affects neurological health. Herein, we have developed a novel magneto-responsive electrochemical enantioselective sensor for the recognition of L-Trp based on oriented biochar derived from Loofah, Fe3O4 nanoparticles, and molecularly imprinted polydopamine (MIPDA) in xanthan hydrogel. The successful synthesis of these materials has been confirmed through physicochemical and electrochemical characterization. Various operational factors such as pH, response time, loading sample volume, and loading of active materials were optimized. As a result, the sensor exhibited an affordable linear range of 1.0-60.0 µM, with a desirable limit of detection of 0.44 µM. Furthermore, the proposed electrochemical sensor demonstrated good reproducibility and desirable selectivity for the determination of L-Trp, making it suitable for analyzing L-Trp levels in human plasma and serum samples. The development presented offers an appealing, easily accessible, and efficient strategy. It utilizes xanthan hydrogel to improve mass transfer and adhesion, biochar-stabilized Fe3O4 to facilitate magnetic orientation and accelerate mass transfer and sensitivity, and polydopamine MIP to enhance selectivity. This approach enables on-site evaluation of L-Trp levels, which holds significant value for healthcare monitoring and early detection of related conditions.

High-performance fentanyl molecularly imprinted electrochemical sensing platform designed through molecular simulations.

BACKGROUND: Fentanyl and its derivatives are a type of potent opioid analgesics, with the characteristics of diverse structure, high toxicity, extremely low content, and high fatality rate. Currently, they have become one of the most serious problems in international drug abuse control due to their extensive use in drug production and use. Therefore, the development of a rapid, sensitive, and accurate method for detecting trace fentanyl is of great significance. In this study, in view of its complex structure and trace concentration, a new molecular imprinting electrochemical sensor was developed through molecular simulations followed by experimental validation to detect trace fentanyl. RESULTS: The process consisted of first obtaining the optimal functional monomer and its molar ratio through molecular simulations. The recognition sites of fentanyl-imprinted polymers were predicted to guide the synthesis of imprinted membranes with precision approach to ensure an efficient and accurate reaction process. Reduced graphene oxide (ErGO) was then deposited on glassy carbon electrode surface by electrochemical reduction to yield large numbers of active sites suitable for catalyzing reactions of fentanyl piperidine for promoted efficient electron transfer and amplified sensitivity of the sensor. Accordingly, fentanyl molecularly imprinted film was formed through one-step electropolymerization to yield greatly improved sensing selectivity due to the specific recognition of molecularly imprinted polymer. Under optimal experimental conditions, the fentanyl sensor showed an extended detection range of 3.84 × 10-9 mol L-1-1.72 × 10-6 mol L-1 and a detection limit of 1.28 × 10-9 mol L-1. SIGNIFICANCE: A distinctive feature of this sensor is its molecularly imprinted polymerized membrane, which offers excellent specific recognition, thereby boosting the sensor's selectivity. Throughout the sensor's development process, molecular simulations were employed to steer the synthesis of molecularly imprinted polymers and predict the recognition sites of fentanyl-imprinted polymers. The experimental outcomes proved to align with the simulation data. The final sensor exhibited outstanding selectivity, repeatability, stability, and high sensitivity. The sensor was effectively used to reliably track fentanyl in human serum samples, with acceptable analytical reliability, suggesting its potential for practical applications.

Chitosan-graphene quantum dot-based molecular imprinted polymer for oxaliplatin release.

Molecularly imprinted polymers (MIPs) have garnered the interest of researchers in the drug delivery due to their advantages, such as exceptional durability, stability, and selectivity. In this study, a biocompatible MIP drug adsorption and delivery system with high loading capacity and controlled release, was prepared based on chitosan (CS) and graphene quantum dots (GQDs) as the matrix, and the anticancer drug oxaliplatin (OXAL) as the template. Additionally, samples without the drug (non-imprinted polymers, NIPs) were created for comparison. GQDs were produced using the hydrothermal method, and samples underwent characterization through FTIR, XRD, FESEM, and TGA. Various experiments were conducted to determine the optimal pH for drug adsorption, along with kinetic and isotherm studies, selectivity assessments, in vitro drug release and kinetic evaluations. The highest drug binding capacity was observed at pH 6.5. The results indicated the Lagergren-first-order kinetic model (with rate constant of 0.038 min-1) and the Langmuir isotherm (with maximum adsorption capacity of 17.15 mg g-1) exhibited better alignment with the experimental data. The developed MIPs displayed significant selectivity towards OXAL, by an imprinting factor of 2.88, in comparison to two similar drugs (cisplatin and carboplatin). Furthermore, the analysis of the drug release profile showed a burst release for CS-Drug (87% within 3 h) at pH 7.4, where the release from the CS-GQD-Drug did not occur at pH 7.4 and 10; instead, the release was observed at pH 1.2 in a controlled manner (100% within 28 h). Consequently, this specific OXAL adsorption and delivery system holds promise for cancer treatment.

Reusable magnetic molecular imprinted polymers based on magnetic graphene oxide for selective identification and detection of eugenol in environmental water samples.

In this study, a reliable method for determining eugenol content in environmental water samples was established by combining magnetic solid-phase extraction with high-performance liquid chromatography. Magnetic molecular imprinted polymers MGO@MIPs were prepared through surface molecular imprinting technique with eugenol as the template molecule. The material displayed good superparamagnetic properties and magnetic responsiveness in favor of rapid separation. The adsorption properties of MGO@MIPs for eugenol were evaluated through adsorption kinetics and selectivity experiments. MGO@MIPs were found to have favorable reusability and obvious selectivity for eugenol. In addition, adsorption and elution conditions were investigated. Under optimal conditions, a linear relationship was obtained between the concentration of eugenol and its peak area in the range of 0.02-5 mg/L (R2 = 0.9998) and the limit of detection was 4.0 × 10-6 mg/mL. The performance of the established method was assessed with the average recovery of 96.59-102.20% and the relative standard deviation (RSD) below 3.5%. The application of this method provides a new perspective for the separation, enrichment and detection of eugenol in water environment.

Bilateral efforts to improve SERS detection efficiency of exosomes by Au/Na7PMo11O39 Combined with Phospholipid Epitope Imprinting.

Detection of cancer-related exosomes in body fluids has become a revolutionary strategy for early cancer diagnosis and prognosis prediction. We have developed a two-step targeting detection method, termed PS-MIPs-NELISA SERS, for rapid and highly sensitive exosomes detection. In the first step, a phospholipid polar site imprinting strategy was employed using magnetic PS-MIPs (phospholipids-molecularly imprinted polymers) to selectively isolate and enrich all exosomes from urine samples. In the second step, a nanozyme-linked immunosorbent assay (NELISA) technique was utilized. We constructed Au/Na7PMo11O39 nanoparticles (NPs) with both surface-enhanced Raman scattering (SERS) property and peroxidase catalytic activity, followed by the immobilization of CD9 antibodies on the surface of Au/Na7PMo11O39 NPs. The Au/Na7PMo11O39-CD9 antibody complexes were then used to recognize CD9 proteins on the surface of exosomes enriched by magnetic PS-MIPs. Lastly, the high sensitivity detection of exosomes was achieved indirectly via the SERS activity and peroxidase-like activity of Au/Na7PMo11O39 NPs. The quantity of exosomes in urine samples from pancreatic cancer patients obtained by the PS-MIPs-NELISA SERS technique showed a linear relationship with the SERS intensity in the range of 6.21 × 107-2.81 × 108 particles/mL, with a limit of detection (LOD) of 5.82 × 107 particles/mL. The SERS signal intensity of exosomes in urine samples from pancreatic cancer patients was higher than that of healthy volunteers. This bidirectional MIPs-NELISA-SERS approach enables noninvasive, highly sensitive, and rapid detection of cancer, facilitating the monitoring of disease progression during treatment and opening up a new avenue for rapid early cancer screening.

Molecularly imprinted electrochemical biosensor for thrombin detection by comparing different monomers.

Aim: Investigating molecularly imprinted polymers (MIPs) in electrochemical biosensors for thrombin detection, an essential protein biomarker. Comparing different monomers to showcase distinct sensitivity, specificity and stability advantages. Materials & methods: Dopamine, thionine and ethanolamine serve as monomers for MIP synthesis. Electrochemical methods and atomic force microscopy characterize sensor surfaces. Performance is evaluated, emphasizing monomer-specific electrochemical responses. Results: Monomer-specific electrochemical responses highlight dopamine's superior signal change and stability over 30 days. Notably, a low 5 pg/ml limit of detection, a broad linear range (5-200 pg/ml) and enhanced selectivity against interferents are observed. Conclusion: Dopamine-based MIPs show promise for high-performance electrochemical thrombin biosensors, suggesting significant applications in clinical diagnostics.

Fluorescent Probes Based on Ag NPs@N/GQDs and Molecularly Imprinted Polymer for Sensitive Detection of Noradrenaline in Bananas.

Fluorescence intensity and selective recognition ability are crucial factors in determining the analytical techniques for fluorescent probes. In this study, a core-shell fluorescent material, composed of silver nanoparticles@nitrogen-doped graphene quantum dots (Ag NPs@N/GQDs), was synthesised using mango leaves as the raw material through a thermal cracking method, resulting in strong fluorescence luminescence intensity. By employing noradrenaline as a template molecule and using a surface molecular imprinting technique, a molecularly imprinted membrane (MIP) was formed on the surface of the fluorescent material, that was subsequently eluted to obtain a highly specific, fluorescent probe capable of recognising noradrenaline. The probe captured various concentrations of noradrenaline using the MIP, which decreased the fluorescence intensity. Then a method for detecting trace amounts of noradrenaline was established. This method exhibited a linear range from 0.5 -700 pM with a detection limit of 0.154 pM. The proposed method was implemented in banana samples. Satisfactory recoveries were confirmed at four different concentrations. The method presented a relative standard deviation (RSD) of less than 5.0%.

Magnetic molecular imprinted covalent organic framework composite for the magnetic solid-phase extraction of bisphenol AF.

A magnetic molecular imprinted covalent organic framework composite (MCOF-MIP) that possessed the 'dual-selectivity' of a covalent organic framework and molecular imprinted polymer (MIP) with rapid response performance was successfully prepared for the removal of bisphenol AF (BPAF) from real water and blood samples. First, the MCOF was separately synthesized using magnetic Fe3O4 as the magnetic core, 1,3,5-triaminobenzene and 2,5-dibromobenzene-1,4-diformaldehyde as precursors and a deep eutectic solvent (DES) as the solvent using a solvothermal synthesis method. The MCOF showed high crystallinity and good adsorption capacities for BPAF (107.4 mg g-1), bisphenol A (113.6 mg g-1), bisphenol S (120.0 mg g-1) and bisphenol F (82.1 mg g-1). To further improve the selectivity for BPAF, an MIP, which uses BPAF as a template, was introduced to form the MCOF-MIP. Due to the dual selectivity of MCOF and MIP, the MCOF-MIP exhibited relatively high selective adsorption capacity to BPAF (243.1 mg g-1) compared to that for the MCOF (107.4 mg g-1), while the adsorption capacities (149.7-109.4 mg g-1) for the other three compounds were not significantly improved. Furthermore, a magnetic solid-phase extraction (MSPE) method was established, and MSPE parameters such as adsorbent dosage, adsorption time, desorption solvent and desorption time were optimized. Combined with high-performance liquid chromatography with diode-array detection (HPLC-DAD) analysis, a rapid and sensitive method was developed to detect BPAF, which showed good linearity (r > 0.9969) ranging from 0.1 to 400 µg mL-1. Low limits of detection (0.04 µg mL-1, S/N = 3) and quantitation (0.1 µg mL-1, S/N = 10) and good precision with low relative SDs (<1.2 % for intra-day and <1.1 % for inter-day) were also obtained. Finally, MSPE coupled with HPLC-DAD was employed for the analysis of BPAF in water and blood samples, and the recoveries of BPAF were satisfactory (91.1-112.6 %).

Synthesis of molecularly imprinted polymer by precipitation polymerization for the removal of ametryn.

Ametryn (AME) is a triazine herbicide which is mainly used to kill unwanted herbs in crops. Despite its importance in agriculture, the usage of AME also poses a risk to humans and the ecosystem due to its toxicity. Hence, it is important to develop a method for the effective removal of AME from various water sources which is in the form of molecular imprinting polymer (MIP). In this study, MIP of AME was synthesized via precipitation polymerization using AME as the template molecule with three different functional monomers including methacrylic acid (MAA), acrylamide (AAm) and 2-vinylpyridine (2VP). The three different synthesized polymers namely MIP (MAA), MIP (AAm) and MIP (2VP) were characterized using Fourier Infra-red spectroscopy (FTIR) and Field Emission Electron Microscopy (FESEM). Then, the batch binding study was carried out using all three MIPs in which MIP (MAA) attained the highest rebinding efficiency (93.73%) among the synthesized polymers. The Energy-Dispersive X-ray spectroscopy (EDX) analysis, Brunauer-Emmett-Teller (BET) analysis and thermogravimetric analysis (TGA) were also conducted on the selected MIP (MAA). Adsorption studies including initial concentration, pH and polymer dosage were also conducted on MIP (MAA). In this study, the highest adsorption efficiency was attained at the optimum condition of 6 ppm of AME solution at pH 7 with 0.1 g of MIP (MAA). MIP (MAA) was successfully applied to remove AME from spiked distilled water, tap water and river water samples with removal efficiencies of 95.01%, 90.24% and 88.37%, respectively.

Electrochemical chiral sensor for levofloxacin detection base on Cu/Fe-BTC amplification.

The key to developing sensors for chiral drug determination is to exclude interference from enantiomers. In this study, metal-organic frameworks (MOFs) and molecularly imprinted polymer (MIP) were introduced to prepare a chiral sensor for levofloxacin detection. The MIP was electropolymerised on the surface of the Cu/Fe-benzene-1,3,5-tricarboxylate MOF (Cu/Fe-BTC)-modified Au electrode using levofloxacin as a template molecule. After eluting the levofloxacin, a chiral sensor with recognition sites for levofloxacin was obtained. With this site as a switch, a novel method for detecting levofloxacin was established. Because of the enhanced recognition effect, the sensor can effectively exclude the enantiomeric interference of d-ofloxacin. Moreover, Cu/Fe-BTC can effectively amplify the current response signal and improve the sensitivity of the sensor. The linear range of the sensor was 5 to 4000 × 10-11 mol L-1, and the detection limit was 2.07 × 10-11 mol L-1. When applied to detecting levofloxacin in actual samples, the sensor showed a 92.7-109.8% recovery.

Molecular imprinted polymer-based potentiometric approach for the assay of the co-formulated tetracycline HCl, metronidazole and bismuth subcitrate in capsules and spiked human plasma.

BACKGROUND: An anti-H-pylori co-formulated mixture of tetracycline HCl (TET), metronidazole (MET), and bismuth subcitrate (BSC) is recently available. Only two chromatographic and spectrophotometric methods are reported for determining those drugs simultaneously where the effect of impurities that could be present as well as the biological fluids matrix influence do not be taken into consideration. There is a need to develop an easy-to-use potentiometric technique for analysis of TET, MET, and BSC in their co-formulated capsules, in presence of some official impurities and in spiked human plasma. RESULTS: Three carbon paste electrodes (CPEs) were fabricated for this purpose. Being a solid contact ion-selective electrode, CPE suffers from the creation of a water layer affecting its stability and reproducibility. Besides, it has a common problem in differentiation between two drugs carrying the same charge (positively charged TET and MET). Water layer formation was prevented through inserting polyaniline nanoparticles (≈10.0 nm diameter) between solid contact and ion-sensing membrane in the three proposed sensors. TET and MET interference was overcome by synthesizing a corresponding molecular imprinted polymer (MIP) for each drug. The synthesized MIPs were inserted in equivalent sensing membranes and characterized using several techniques. The suggested MIPs have a noticeable enhanced sensitivity in potentiometric determination. The obtained LODs were 5.88 × 10-8, 5.19 × 10-7, and 1.73 × 10-6 M for TET, MET and BSC proposed CPEs, respectively, with corresponding slopes of 57.37, 56.20, and -57.40 mV decade-1. SIGNIFICANCE: The proposed potentiometric method makes the detection of the three cited drugs simple, fast, and feasible. This approach is the first for determining three drugs potentiometrically in one combined formulation. The obtained results were compared favorably with previously reported potentiometric methods.

All-solid-state chip utilizing molecular imprinted polymer for erythromycin detection in milk samples: Printed circuit board-based potentiometric system.

Detection of erythromycin (ERY) residues in commercial milk samples is crucial for the safety assessment. Herein, a printed circuit board was patterned as a feasible miniaturized potentiometric sensor for ERY determination in dairy samples. The proposed chip design fits to a 3.5-mm female audio plug to facilitate the potential measurements of working electrode versus reference one in this all-solid-state system. The sensor utilizes molecular imprinted polymer (MIP) for the selective recognition of the studied drug in such challenging matrix. The electrode stability is achieved through the addition of poly (3,4-ethylenedioxythiophene) nano-dispersion on its surface. The proposed device detects down to 6.6 × 10-8 M ERY with a slope of 51 mV/decade in the 1 × 10-7-1 × 10-3 M range. The results display high accuracy (99.9% ± 2.6) with satisfactory relative standard deviation for repeatability (1.6%) and reproducibility (5.0%). The effect of common antibiotic classes, namely, amphenicols, beta-lactams, fluoroquinolones, sulfonamides, and tetracyclines, can be neglected as evidenced by their calculated binding capacities towards the proposed MIP. The calculated selectivity coefficients also show a good electrode performance in the presence of naturally present inorganic ions allowing its application to different milk samples.

Transitioning from Supramolecular Chemistry to Molecularly Imprinted Polymers in Chemical Sensing.

This perspective article focuses on the overwhelming significance of molecular recognition in biological processes and its emulation in synthetic molecules and polymers for chemical sensing. The historical journey, from early investigations into enzyme catalysis and antibody-antigen interactions to Nobel Prize-winning breakthroughs in supramolecular chemistry, emphasizes the development of tailored molecular recognition materials. The discovery of supramolecular chemistry and molecular imprinting, as a versatile method for mimicking biological recognition, is discussed. The ability of supramolecular structures to develop selective host-guest interactions and the flexible design of molecularly imprinted polymers (MIPs) are highlighted, discussing their applications in chemical sensing. MIPs, mimicking the selectivity of natural receptors, offer advantages like rapid synthesis and cost-effectiveness. Finally, addressing major challenges in the field, this article summarizes the advancement of molecular recognition-based systems for chemical sensing and their transformative potential.

A Label-Free and Antibody-Free Molecularly Imprinted Polymer-Based Impedimetric Sensor for NSCLC-Cells-Derived Exosomes Detection.

In this study, a label-free and antibody-free impedimetric biosensor based on molecularly imprinting technology for exosomes derived from non-small-cell lung cancer (NSCLC) cells was established. Involved preparation parameters were systematically investigated. In this design, with template exosomes anchored on a glassy carbon electrode (GCE) by decorated cholesterol molecules, the subsequent electro-polymerization of APBA and elution procedure afforded a selective adsorption membrane for template A549 exosomes. The adsorption of exosomes caused a rise in the impedance of the sensor, so the concentration of template exosomes can be quantified by monitoring the impedance of GCEs. Each procedure in the establishment of the sensor was monitored with a corresponding method. Methodological verification showed great sensitivity and selectivity of this method with an LOD = 2.03 × 103 and an LOQ = 4.10 × 104 particles/mL. By introducing normal cells and other cancer cells derived exosomes as interference, high selectivity was proved. Accuracy and precision were measured, with an obtained average recovery ratio of 100.76% and a resulting RSD of 1.86%. Additionally, the sensors' performance was retained at 4 °C for a week or after undergoing elution and re-adsorption cycles seven times. In summary, the sensor is competitive for clinical translational application and improving the prognosis and survival for NSCLC patients.

Ratiometric sensing interface for glutathione determination based on electro-polymerized copper-coordinated molecularly imprinted layer supported on silver/porous carbon hybrid.

A novel molecularly imprinted ratiometric-based sensor was designed for highly selective and ultrasensitive electrochemical detection of glutathione (GSH). The sensor consists of porous carbon co-doped with nitrogen and sulfur formed on the surface of graphite electrode (N, S@PC/GE). Silver nanoparticles (Ag) were grown on the surface of N, S@PC/GE to improve the conductivity/surface area of the sensor and represent an internal reference signal for ratiometric response. The monomer (pyrrole-4-carboxylic acid, Py-COOH) was electro-polymerized on the surface of Ag/N, S@PC/GE in the presence of Cu (II) to form Cu-MIP@Ag/N, S@PC/GE. Addition of GSH decreased the signal of Ag at 0.18 V (oxidation of Ag) due to coordination complexation, while the signal response at 0.83 V (oxidation of Ag-GSH complex) was increased. Under optimum conditions, the ratio response (IGSH/IAg) was increased with increasing the concentration of GSH in the range of 0.01-500 nM with a detection limit (S/N = 3) of 0.003 nM. The electrochemical sensor exhibits many advantages including low LOD, high selectivity, good reproducibility, and satisfactory stability. The sensor was successfully applied to determine GSH in dietary supplements and human serum samples with recoveries % ranged from 97.4 to 101.8% and relative standard deviation % (RSD %) did not exceed 3.8%. This research paper introduces new information for the construction of molecular imprinted ratiometric-based electrochemical sensors for highly selective and sensitive detection of (bio) molecules.

A Novel Hexokinases Inhibitor Based on Molecularly Imprinted Polymer for Combined Starvation and Enhanced Photothermal Therapy of Malignant Tumors.

The heat tolerance of tumor cells induced by heat shock proteins (HSPs) is the major factor that seriously hinders further application of PTT, as it can lead to tumor inflammation, invasion, and even recurrence. Therefore, new strategies to inhibit HSPs expression are essential to improve the antitumor efficacy of PTT. Here, we prepared a novel nanoparticle inhibitor by synthesizing molecularly imprinted polymers with a high imprinting factor (3.1) on the Prussian Blue surface (PB@MIP) for combined tumor starvation and photothermal therapy. Owing to using hexokinase (HK) epitopes as the template, the imprinted polymers could inhibit the catalytic activity of HK to interfere with glucose metabolism by specifically recognizing its active sites and then achieve starvation therapy by restricting ATP supply. Meanwhile, MIP-mediated starvation downregulated the ATP-dependent expression of HSPs and then sensitized tumors to hyperthermia, ultimately improving the therapeutic effect of PTT. As the inhibitory effect of PB@MIP on HK activity, more than 99% of the mice tumors were eliminated by starvation therapy and enhanced PTT.

Molecularly imprinted polymers (MIPs): emerging biomaterials for cancer theragnostic applications.

Cancer is a disease caused by abnormal cell growth that spreads through other parts of the body and threatens life by destroying healthy tissues. Therefore, numerous techniques have been employed not only to diagnose and monitor the progress of cancer in a precise manner but also to develop appropriate therapeutic agents with enhanced efficacy and safety profiles. In this regard, molecularly imprinted polymers (MIPs), synthetic receptors that recognize targeted molecules with high affinity and selectivity, have been intensively investigated as one of the most attractive biomaterials for theragnostic approaches. This review describes diverse synthesis strategies to provide the rationale behind these synthetic antibodies and provides a selective overview of the recent progress in the in vitro and in vivo targeting of cancer biomarkers for diagnosis and therapeutic applications. Taken together, the topics discussed in this review provide concise guidelines for the development of novel MIP-based systems to diagnose cancer more precisely and promote successful treatment. Molecularly imprinted polymers (MIPs), synthetic receptors that recognize targeted molecules with high affinity and selectivity, have been intensively investigated as one of the most attractive biomaterials for cancer theragnostic approaches. This review describes diverse synthesis strategies to provide the rationale behind these synthetic antibodies and provides a selective overview of the recent progress in the in vitro and in vivo targeting of cancer biomarkers for diagnosis and therapeutic applications. The topics discussed in this review aim to provide concise guidelines for the development of novel MIP-based systems to diagnose cancer more precisely and promote successful treatment.