Production of polyacrylonitrile nanofibres modified with Cyanex 272 for recovery of gallium from solution.

The objectives of this work were to develop polyacrylonitrile nanofibres modified with the commercial Cyanex 272 extractor and apply them for the recovery of gallium present in aqueous solution. The nanofibres were produced using the centrifugation technique, employing Forcespinning® equipment. The average nanofibre diameter ranged from 530 to 840 nm. The highest adsorption of gallium was achieved at pH 2.5, with a pseudo-second order kinetic model and the Freundlich equilibrium isotherm model providing the best fits of the experimental data. The thermodynamic parameters showed that the adsorption was spontaneous, favourable, and endothermic. The maximum capacity of the PAN/Cyanex 272 nanofibres for the recovery of gallium was 38.93 mg g-1. In successive reuse cycles, the nanofibres showed a small decrease of the adsorption capacity for the metal after the first cycle, while the efficiency remained constant in the subsequent cycles. The desorption efficiency remained constant throughout the cycles, with values in the range 80%-90%. The findings demonstrated that PAN/Cyanex 272 nanofibres have excellent potential for use as adsorbents, providing good capacity for the recovery of gallium and satisfactory stability during reuse in several cycles.

Evaluation of Mechanical Properties of Various Nanofibre Reinforced Bis-GMA/TEGDMA Based Dental Composite Resins / Evaluación de las propiedades mecánicas de varias resinas compuestas dentales basadas en Bis-GMA/TEGDMA reforzadas con nanofibras

ABSTRACT Objective: To investigate the mechanical properties of various mass fractions of Nylon 6 (N6), polymethyl-metacrylate (PMMA) and polyvinylidene-difluoride (PVDF) nanofibres reinforced bisphenol A-glycidyl methacrylate (Bis-GMA) and tri-ethylene glycol dimethacrylate (TEGDMA) based dental composite resins and to evaluate the penetration characteristics of the nanofibres into the resin. Methods: Nylon 6, PMMA and PVDF nanofibres were produced using the electrospinning method. The morphologies of the fabricated nanofibres were evaluated with a scanning electron microscope (SEM). The nanofibres were placed into the resin matrix at different mass fractions (3%, 5% and 7%). The three-point bending test was applied to nanofibre-reinforced dental composite resins and neat resin specimens. The flexural strength (Fs), flexural modulus (EY) and work of fracture (WOF) of the groups were found. The analysis of variance was used for the statistical analysis of the acquired data. Tukey 's multiple test was performed to compare the Fs, EY and WOF means. Fractured surfaces of the samples were observed by SEM, and fracture morphologies were evaluated. Results: Polymethyl-metacrylate nanofibres dissolved in the matrix, and a polymer alloy took place in the matrix. Fibre pull-out and fibre bridging mechanisms were observed by SEM images of the N6 and PVDF nanofibre-reinforced dental composites. The produced nanofibres enhanced the mechanical properties of the dental composite resins. Conclusion: Fibre pull-out and fibre bridging mechanisms on the fractured surfaces of samples may play a key role in the reinforcement of dental composite resins. However, polymer alloy of PMMA nanofibres increased the mechanical properties of the resin matrix.

RESUMEN Objetivo: Investigar las propiedades mecánicas de resinas compuestas dentales basadas en bisfenol A-diglicidildimetacrilato (Bis-GMA) y dimetacrilato trietilen-glicol (TEGDMA) reforzadas con nanofibras de fracciones de masa de Nylon 6 (N6), polimetilmetacrilato (PMMA) y fluoruro de polivinilideno (PVDF), y evaluar las características de la penetración de las nanofibras en la resina. Métodos: Se produjeron nanofibras de Nylon 6, PMMA y PVDF utilizando el método de electrohilado (electrospinning). Las morfologías de las nanofibras fabricadas fueron evaluadas con un microscopio electrónico de barrido (MEB). Las nanofibras fueron introducidas en la matriz de resina en diferentes fracciones de masa (3%, 5% y 7%). La prueba de flexión de tres puntos fue aplicada a las resinas compuestas dentales reforzadas por nanofibras y a las muestras de resina pura. La resistencia a la flexión (Rf), el módulo de flexión (EY) y el trabajo de fractura (WOF) de los grupos fueron halladas. El análisis de varianza se usó para el análisis estadístico de los datos adquiridos. Se realizó la prueba de comparaciones múltiples de Tukey con el propósito de comparar las medidas de Rf, EY y WOF. Las superficies fracturadas de las muestras fueron observadas mediante un MEB, y se evaluaron las morfologías de fractura. Resultados: Las nanofibras de polimetilmetacrilato se disolvieron en la matriz, y tuvo lugar una aleación de polímeros en la matriz. Los mecanismos de desprendimiento de fibras y puenteo de fibras fueron observados mediante imágenes de MEB de los compuestos dentales reforzados con nanofibras de N6 y PVDF. Las nanofibras producidas realzaron las propiedades mecánicas de las resinas compuestas dentales. Conclusión: Los mecanismos de desprendimiento de fibras y puenteo de fibras en las superficies fracturadas de las muestras pueden desempeñar un papel clave en el reforzamiento de las resinas de los compuestos dentales. Sin embargo, la aleación polimérica de las nanofibras de PMMA aumentó las propiedades mecánicas de la matriz de resina.

Novel nanoscale pheromone dispenser for more accurate evaluation of Grapholita molesta (Lepidoptera: Tortricidae) attract-and-kill strategies in the laboratory.

BACKGROUND: Nanotechnology has recently allowed the production of formulations for controlled release of active ingredients. In the present study, the electrospinning technique was used to produce nanoscale dispensers for attract-and-kill strategies. Non-woven nanofibres containing insecticide (cypermethrin) and (E)-8,(Z)-8-dodecenyl acetate and (Z)-8-dodecanol (0.87 mg L-1 ), the main components of Grapholita molesta (Lepidoptera: Tortricidae) (Busck) pheromone, were evaluated in laboratory experiments. Male electroantennographic (EAG) responses and mortality (tarsal-contact and attract-and-kill behavioural cages) bioassays were performed for nanofibres (with and without insecticide) exposed for different periods (21, 42, 63 and 84 days) in controlled and non-exposed conditions. RESULTS: There were no significant differences in G. molesta male EAG responses based on the time of exposure within treatments. Nanofibres with pheromone only and with pheromone plus insecticide elicited equal EAG responses. Mortality in tarsal-contact bioassays was greater than 87% after exposure for 84 days. In the attract-and-kill bioassays, mortality ranged from 28.4 to 56.6%, although no difference was observed on insect mortalities over time (24, 48 and 72 h). CONCLUSION: Incorporation of cypermethrin in nanofibres did not interfere with G. molesta attractiveness. Both aspects of the strategy, the attractant and killing effects, were recorded using innovative nanofibres, and long-term effects suggest a controlled release of pheromone and insecticide. © 2017 Society of Chemical Industry.