2D Graphene Oxide Films Expand Functionality of Photonic Chips.

On-chip integration of 2D materials with unique structures and properties endow integrated devices with new functionalities and improved performance. With high flexibility in ways to modify its properties and compatibility with integrated platforms, graphene oxide (GO) is an exceptionally attractive 2D material for hybrid integrated photonic chips. Here, by harnessing unique property changes induced by photothermal effects in 2D GO films, novel functionalities beyond the capability of photonic integrated circuits are demonstrated. These include all-optical control and tuning, optical power limiting, and nonreciprocal light transmission. The 2D layered GO films are integrated onto photonic chips with precise control of their thickness and size. Benefitting from the broadband optical response of 2D GO films, all three functionalities feature a very wide operational optical bandwidth. By fitting the experimental results with theory, the changes in GO film properties induced by the photothermal effects are analyzed, revealing interesting insights about the physics of 2D GO films. These results highlight the versatility of 2D GO films in implementing new functions for integrated photonic devices for a wide range of applications.

Modelling and Thermographic Measurements of LED Optical Power.

This paper presents a simple engineering method for evaluating the optical power emitted by light-emitting diodes (LEDs) using infrared thermography. The method is based on the simultaneous measurement of the electrical power and temperature of an LED and a heat source (resistor) that are enclosed in the same plastic packaging under the same cooling conditions. This ensures the calculation of the optical power emitted by the LED regardless of the value of the heat transfer coefficient. The obtained result was confirmed by comparing it with the standard direct measurement method using an integrated sphere. The values of the estimated optical power using the proposed method and the integrated sphere equipped with a spectrometer were consistent with each other. The tested LED exhibited a high optical energy efficiency, reaching approximately η ≈ 30%. In addition, an uncertainty analysis of the obtained results was performed. Compact modelling based on a thermal resistor network (Rth) and a 3D-FEM analysis were performed to confirm the experimental results.

Two-Photon Absorbing Dendrimers and Their Properties-An Overview.

This review describes the two-photon absorption properties of dendrimers, which are arborescent three-dimensional macromolecules differing from polymers by their perfectly defined structure. The two-photon absorption process is a third order non-linear optical property that is attractive because it can be used in a wide range of applications. In this review, dendrimers that were studied for their two-photon absorption properties are first described. Then, the use of dendritic TPA chromophores for light harvesting, photopolymerization, optical power limitation, cell imaging, singlet oxygen generation, and photodynamic therapy is described. This review thus proposes an overview of the properties and possible applications of two-photon absorbing dendrimers.

Thermal Behavior of Biaxial Piezoelectric MEMS-Scanners.

This paper presents the thermal behavior of non-resonant (quasi-static) piezoelectric biaxial MEMS scanners with Bragg reflectors. These scanners were developed for LIDAR (LIght Detection And Ranging) applications using a pulsed 1550 nm laser with an average power of 2 W. At this power, a standard metal (gold) reflector can overheat and be damaged. The Bragg reflector developed here has up to 24 times lower absorption than gold, which limits heating of the mirror. However, the use of such a reflector involves a technological process completely different from that used for gold and induces, for example, different final stresses on the mirror. In view of the high requirements for optical power, the behavior of this reflector in the event of an increase in temperature needs to be studied and compared with the results of previous studies using gold reflectors. This paper shows that the Bragg reflector remains functional as the temperature rises and undergoes no detrimental deformation even when heated to 200 °C. In addition, the 2D-projection model revealed a 5% variation in optical angle at temperatures up to 150 °C and stability of 2D scanning during one hour of continuous use at 150 °C. The results of this study demonstrate that a biaxial piezoelectric MEMS scanner equipped with Bragg reflector technology can reach a maximum temperature of 150 °C, which is of the same order of magnitude as can be reached by scanners with gold reflectors.

Brightness of AlGaInAs/InP Multimode Diode Lasers with Different Aperture Widths.

A set of semiconductor lasers with different stripe widths is fabricated based on the AlGaInAs/InP heterostructure with an ultra-narrow waveguide. The key characteristics of the lasers (light-current curves (L-I), current-voltage curves (I-V), and spectral and spatial characteristics) are measured, and their dependence on the stripe width is shown. The operating optical power increases from 1.4 W to 4.3 W; however, the lateral brightness decreases from 1.09 W/(mm*mrad) to 0.65 W/(mm*mrad) as the stripe width increases from 20 to 150 µm.

Ultra-Compact and Broadband Nano-Integration Optical Phased Array.

The on-chip nano-integration of large-scale optical phased arrays (OPAs) is a development trend. However, the current scale of integrated OPAs is not large because of the limitations imposed by the lateral dimensions of beam-splitting structures. Here, we propose an ultra-compact and broadband OPA beam-splitting scheme with a nano-inverse design. We employed a staged design to obtain a T-branch with a wavelength bandwidth of 500 nm (1300-1800 nm) and an insertion loss of -0.2 dB. Owing to the high scalability and width-preserving characteristics, the cascaded T-branch configuration can significantly reduce the lateral dimensions of an OPA, offering a potential solution for the on-chip integration of a large-scale OPA. Based on three-dimensional finite-difference time-domain (3D FDTD) simulations, we demonstrated a 1 × 16 OPA beam-splitter structure composed entirely of inverse-designed elements with a lateral dimension of only 27.3 µm. Additionally, based on the constructed grating couplers, we simulated the range of the diffraction angle θ for the OPA, which varied by 0.6°-41.6° within the wavelength range of 1370-1600 nm.

Flexible Data Rate Allocation Using Non-Orthogonal Multiple Access (NOMA) in a Mode Division Multiplexing (MDM) Optical Power Splitter for System-on-Chip Networks.

We put forward and demonstrate a silicon photonics (SiPh)-based mode division multiplexed (MDM) optical power splitter that supports transverse-electric (TE) single-mode, dual-mode, and triple-mode (i.e., TE0, TE1, and TE2). An optical power splitter is needed for optical signal distribution and routing in optical interconnects. However, a traditional optical splitter only divides the power of the input optical signal. This means the same data information is received at all the output ports of the optical splitter. The powers at different output ports may change depending on the splitting ratio of the optical splitter. The main contributions of our proposed optical splitter are: (i) Different data information is received at different output ports of the optical splitter via the utilization of NOMA. By adjusting the power ratios of different channels in the digital domain (i.e., via software control) at the Tx, different channel data information can be received at different output ports of the splitter. It can increase the flexibility of optical signal distribution and routing. (ii) Besides, the proposed optical splitter can support the fundamental TE0 mode and the higher modes TE1, TE2, etc. Supporting mode-division multiplexing and multi-mode operation are important for future optical interconnects since the number of port counts is limited by the chip size. This can significantly increase the capacity besides wavelength division multiplexing (WDM) and spatial division multiplexing (SDM). The integrated SiPh MDM optical power splitter consists of a mode up-conversion section implemented by asymmetric directional couplers (ADCs) and a Y-branch structure for MDM power distribution. Here, we also propose and discuss the use of the Genetic algorithm (GA) for the MDM optical power splitter parameter optimization. Finally, to provide adjustable data rates at different output ports after the MDM optical power splitter, non-orthogonal multiple access-orthogonal frequency division multiplexing (NOMA-OFDM) is also employed. Experimental results validate that, in three modes (TE0, TE1, and TE2), user-1 and user-2 achieve data rates of (user-1: greater than 22 Gbit/s; user-2: greater than 12 Gbit/s) and (user-1: greater than 12 Gbit/s; user-2: 24 Gbit/s), respectively, at power-ratio (PR) = 2.0 or 3.0. Each channel meets the hard-decision forward-error-correction (HD-FEC, i.e., BER = 3.8 × 10-3) threshold. The proposed method allows flexible data rate allocation for multiple users for optical interconnects and system-on-chip networks.

An Optical 1×4 Power Splitter Based on Silicon-Nitride MMI Using Strip Waveguide Structures.

This paper presents a new design for a 1 × 4 optical power splitter using multimode interference (MMI) coupler in silicon nitride (Si3N4) strip waveguide structures. The main functionality of the proposed design is to use Si3N4 for dealing with the back reflection (BR) effect that usually happens in silicon (Si) MMI devices due to the self-imaging effect and the higher index contrast between Si and silicon dioxide (SiO2). The optimal device parameters were determined through numerical optimizations using the beam propagation method (BPM) and finite difference time domain (FDTD). Results demonstrate that the power splitter with a length of 34.6 µm can reach equal distribution power in each output port up to 24.3% of the total power across the O-band spectrum with 0.13 dB insertion loss and good tolerance MMI coupler parameters with a shift of ±250 nm. Additionally, the back reflection range over the O-band was found to be 40.25-42.44 dB. This demonstrates the effectiveness of the incorporation using Si3N4 MMI and adiabatic input and output tapers in mitigating unwanted BR to ensure that a good signal is received from the laser. This design showcases the significant potential for data-center networks, offering a promising solution for efficient signal distribution and facilitating high-performance and reliable optical signal routing within the O-band range. By leveraging the advantages of Si3N4 and the MMI coupler, this design opens possibilities for advanced optical network architectures and enables efficient transmission of optical signals in the O-band range.

Optical engineering of infrared PbS CQD photovoltaic cells for wireless optical power transfer systems.

Infrared photovoltaic cells (IRPCs) have attracted considerable attention for potential applications in wireless optical power transfer (WOPT) systems. As an efficient fiber-integrated WOPT system typically uses a 1550 nm laser beam, it is essential to tune the peak conversion efficiency of IRPCs to this wavelength. However, IRPCs based on lead sulfide (PbS) colloidal quantum dots (CQDs) with an excitonic peak of 1550 nm exhibit low short circuit current (Jsc) due to insufficient absorption under monochromatic light illumination. Here, we propose comprehensive optical engineering to optimize the device structure of IRPCs based on PbS CQDs, for 1550 nm WOPT systems. The absorption by the device is enhanced by improving the transmittance of tin-doped indium oxide (ITO) in the infrared region and by utilizing the optical resonance effect in the device. Therefore, the optimized device exhibited a high short circuit current density of 37.65 mA/cm2 under 1 sun (AM 1.5G) solar illumination and 11.91 mA/cm2 under 1550 nm illumination 17.3 mW/cm2. Furthermore, the champion device achieved a record high power conversion efficiency (PCE) of 7.17% under 1 sun illumination and 10.29% under 1550 nm illumination. The PbS CQDs IRPCs under 1550 nm illumination can even light up a liquid crystal display (LCD), demonstrating application prospects in the future.

Co-packaged optics (CPO): status, challenges, and solutions.

Due to the rise of 5G, IoT, AI, and high-performance computing applications, datacenter traffic has grown at a compound annual growth rate of nearly 30%. Furthermore, nearly three-fourths of the datacenter traffic resides within datacenters. The conventional pluggable optics increases at a much slower rate than that of datacenter traffic. The gap between application requirements and the capability of conventional pluggable optics keeps increasing, a trend that is unsustainable. Co-packaged optics (CPO) is a disruptive approach to increasing the interconnecting bandwidth density and energy efficiency by dramatically shortening the electrical link length through advanced packaging and co-optimization of electronics and photonics. CPO is widely regarded as a promising solution for future datacenter interconnections, and silicon platform is the most promising platform for large-scale integration. Leading international companies (e.g., Intel, Broadcom and IBM) have heavily investigated in CPO technology, an inter-disciplinary research field that involves photonic devices, integrated circuits design, packaging, photonic device modeling, electronic-photonic co-simulation, applications, and standardization. This review aims to provide the readers a comprehensive overview of the state-of-the-art progress of CPO in silicon platform, identify the key challenges, and point out the potential solutions, hoping to encourage collaboration between different research fields to accelerate the development of CPO technology.

Enhanced Ultrafast Broadband Reverse Saturable Absorption in Twistacenes with Enlarged π-Conjugated Central Bridge.

Optical nonlinearities of two all-carbon twistacenes, DPyA and DPyN, with the different π-conjugated central bridges were investigated. The nonlinear absorption properties of these compounds were measured using the femtosecond Z-scan with wavelengths between 650 and 900 nm. It has been found that the nonlinear absorption originated from two-photon absorption (TPA) and TPA-induced excited state absorption (ESA), wherein DPyA demonstrates higher performance than DPyN. The TPA cross section of DPyA (4300 GM) is nearly 4.3 times larger than that of DPyN at 650 nm. Moreover, the different central structures modulate the intensity of ESA at 532 nm, and DPyA exhibits an excellent ESA at 532 nm with multi-pulse excitation. Meanwhile, the result of data fitting and quantum chemistry calculation shows that the enhancement of nonlinear absorption in DPyA is due to the extended π- conjugated bridge and improved delocalization of π-electrons. These all-carbon twistacenes could yield potential applications in optical power limiting (OPL) technology.

[The effect of intraocular pressure on refractive power of the cornea and the human eye, based on the Liou-Brennan model eye]. / A szemnyomás változásának hatása a szaruhártya és a szem töroerejére a Liou­Brennan-modellszem alapján.

INTRODUCTION: It is a clinical experience that with significantly higher intraocular pressure, glass ordering may be inaccurate, therefore, it should be performed after adjustment of intraocular pressure. OBJECTIVE: To analyze the effect of intraocular pressure on the refractive power of the cornea and of the eye, using geometrical properties of the Liou-Brennan model eye and finite element modeling. METHODS: Using corneal parameters of the Liou-Brennan model eye, a parametric geometrical model and with these data finite element modelling, using the Ansys (Ansys, Canonsburg, PA, USA) program, has been performed. Corneal tissue properties have been defined based on trilinear material model of Wollensak and boundary conditions based on Pandolfi. The effect of changes in intraocular pressure on geometrical corneal properties with optical impact (corneal curvature at the anterior and posterior corneal surface at the optical center and axial displacement of the anterior and posterior corneal surface points at the optical center) have been analyzed. Based on the geometric characteristics obtained, using the paraxial ray tracing method, changes in the optical properties of the cornea and the eye have been calculated. RESULTS: With increasing intraocular pressure load, anterior and posterior central corneal radius of curvature decreased and corneal surface points at the optical center at the anterior and posterior surface moved forwards, the cornea thinned. Axial displacement of corneal volume points was maximal for all pressure load values at the optical center of the posterior corneal surface. The refractive power of the cornea decreased as eye pressure increased, while the refractive power of the entire eye increased. CONCLUSION: We verified using the Liou-Brennan model eye and finite element modelling that a change of the intraocular pressure load between 10 and 30 mmHg may result in 0.31-0.86 mm decrease of the corneal radius of curvature, in 1.5-4.8 D increase in the keratometric values and in about 1.2-3.9 D increase in the total optical power of the eye. A decrease of 0.14 D to 0.69 D has been measured in the corneal optical power in the examined eye pressure range. Orv Hetil. 2022; 163(47): 1872-1879.

Infrared Transmission Characteristics of Phase Transitioning VO2 on Various Substrates.

Infrared transmission characteristics of VO2 thin films synthesized on multiple substrates, using a low-pressure direct oxidation technique, have been characterized. Material characterization of these films indicates high material quality, which resulted in large variation of electrical and optical properties at phase transition. A change in optical transmissivity greater than 80% was observed for these films utilizing infrared (IR) laser illumination at 1550 nm. Phase transition enabled by temperature change induced by a pulsed high-power laser beam resulted in modulated IR laser transmission with a low time constant in VO2 on transparent quartz and muscovite substrates. Investigation of the effect of mechanical strain on phase transition in VO2 grown on flexible muscovite substrate indicate shift in transition temperature to higher for tensile and lower for compressive strains.

High Performance Predictable Quantum Efficient Detector Based on Induced-Junction Photodiodes Passivated with SiO2/SiNx.

We performed a systematic study involving simulation and experimental techniques to develop induced-junction silicon photodetectors passivated with thermally grown SiO2 and plasma-enhanced chemical vapor deposited (PECVD) SiNx thin films that show a record high quantum efficiency. We investigated PECVD SiNx passivation and optimized the film deposition conditions to minimize the recombination losses at the silicon-dielectric interface as well as optical losses. Depositions with varied process parameters were carried out on test samples, followed by measurements of minority carrier lifetime, fixed charge density, and optical absorbance and reflectance. Subsequently, the surface recombination velocity, which is the limiting factor for internal quantum deficiency (IQD), was obtained for different film depositions via 2D simulations where the measured effective lifetime, fixed charge density, and substrate parameters were used as input. The quantum deficiency of induced-junction photodiodes that would be fabricated with a surface passivation of given characteristics was then estimated using improved 3D simulation models. A batch of induced-junction photodiodes was fabricated based on the passivation optimizations performed on test samples and predictions of simulations. Photodiodes passivated with PECVD SiNx film as well as with a stack of thermally grown SiO2 and PECVD SiNx films were fabricated. The photodiodes were assembled as light-trap detector with 7-reflections and their efficiency was tested with respect to a reference Predictable Quantum Efficient Detector (PQED) of known external quantum deficiency. The preliminary measurement results show that PQEDs based on our improved photodiodes passivated with stack of SiO2/SiNx have negligible quantum deficiencies with IQDs down to 1 ppm within 30 ppm measurement uncertainty.

Design of an electrostatic balance mechanism to measure optical power of 100 kW.

A new instrument is required to accommodate the need for increased portability and accuracy in laser power measurement above 100 W. Reflection and absorption of laser light provide a measurable force from photon momentum exchange that is directly proportional to laser power, which can be measured with an electrostatic balance traceable to the SI. We aim for a relative uncertainty of 10-3 with coverage factor k = 2. For this purpose, we have designed a monolithic parallelogram 4-bar linkage incorporating elastic circular notch flexure hinges. The design is optimized to address the main factors driving force measurement uncertainty from the balance mechanism: corner loading errors, balance stiffness, stress in the flexure hinges, sensitivity to vibration, and sensitivity to thermal gradients. Parasitic rotations in the free end of the 4-bar linkage during arcuate motion are constrained by machining tolerances. An analytical model shows this affects the force measurement less than 0.01 percent. Incorporating an inverted pendulum reduces the stiffness of the system without unduly increasing tilt sensitivity. Finite element modeling of the flexures is used to determine the hinge orientation that minimizes stress which is therefore expected to minimize hysteresis. Thermal effects are mitigated using an external enclosure to minimize temperature gradients, although a quantitative analysis of this effect is not carried out. These analyses show the optimized mechanism is expected to contribute less than 1 × 10-3 relative uncertainty in the final laser power measurement.

Improvement of Temperature and Optical Power of an LED by Using Microfluidic Circulating System of Graphene Solution.

Electric devices have evolved to become smaller, more multifunctional, and increasingly integrated. When the total volume of a device is reduced, insufficient heat dissipation may result in device failure. A microfluidic channel with a graphene solution may replace solid conductors for simultaneously supplying energy and dissipating heat in a light emitting diode (LED). In this study, an automated recycling system using a graphene solution was designed that reduces the necessity of manual operation. The optical power and temperature of an LED using this system was measured for an extended period and compared with the performance of a solid conductor. The temperature difference of the LED bottom using the solid and liquid conductors reached 25 °C. The optical power of the LED using the liquid conductor was higher than that of the solid conductor after 120 min of LED operation. When the flow rate was increased, the temperature difference of the LED bottom between initial and 480 min was lower, and the optical power of the LED was higher. This result was attributable to the higher temperature of the LED with the solid conductor. Moreover, the optical/electric power transfer rate of the liquid conductor was higher than that of the solid conductor after 120 min of LED operation, and the difference increased over time.

Wireless Power Transfer Techniques for Implantable Medical Devices: A Review.

Wireless power transfer (WPT) systems have become increasingly suitable solutions for the electrical powering of advanced multifunctional micro-electronic devices such as those found in current biomedical implants. The design and implementation of high power transfer efficiency WPT systems are, however, challenging. The size of the WPT system, the separation distance between the outside environment and location of the implanted medical device inside the body, the operating frequency and tissue safety due to power dissipation are key parameters to consider in the design of WPT systems. This article provides a systematic review of the wide range of WPT systems that have been investigated over the last two decades to improve overall system performance. The various strategies implemented to transfer wireless power in implantable medical devices (IMDs) were reviewed, which includes capacitive coupling, inductive coupling, magnetic resonance coupling and, more recently, acoustic and optical powering methods. The strengths and limitations of all these techniques are benchmarked against each other and particular emphasis is placed on comparing the implanted receiver size, the WPT distance, power transfer efficiency and tissue safety presented by the resulting systems. Necessary improvements and trends of each WPT techniques are also indicated per specific IMD.

Simulation of the Effect of Material Properties on Soft Contact Lens On-Eye Power.

PURPOSE: To evaluate the variation in the optical power achieved following soft contact lens eye fitting for spherical and cylindrical lenses with differing hydrogel material properties. METHODS: Uniaxial tensile tests were performed on four hydrogel materials 77% water-content (w-c) hydrogel, 74% w-c blue silicone hydrogel, 74% w-c clear silicone hydrogel, and 64% w-c clear hydrogel (shortly referred to as H77p0, SiH74p5-blue, SiH74p5-clear, and H64p0-clear), under loading conditions that would be expected in vivo. Finite element models of the cornea and contact lens interaction were generated using spherical and cylindrical lenses with powers varying from -10 to +20 D; overall diameters of either 13.5, 14.0, or 14.5 mm; and with material properties matching those determined through experimental testing. RESULTS: The moduli of elasticity for each of the tested hydrogel materials were 0.195 ± 0.027 MPa, 0.277 ± 0.019 MPa, 0.279 ± 0.01 MPa, and 0.457 ± 0.013 MPa for H77p0, SiH74p5-blue, SiH74p5-clear, and H64p0 respectively. The calculated values of effective power change (EPC) showed strong negative correlations with lens power. This was particularly apparent in the higher end of the lens power spectrum (over +5 D), where each of the materials demonstrated a highly linear reduction in EPC with increased lens power. CONCLUSIONS: Soft contact lenses composed of a stiffer hydrogel are far more resilient to changes in EPC across the lower end of the lens power spectrum (-10 to +5 D). Beyond this range, the material choice does not have a significant effect on the EPC.

"Seeing" and Controlling Photoisomerization by (Z)-/(E)-Isomers with Aggregation-Induced Emission Characteristics.

Efficient photoisomerization of chromophores is important in living systems, and structural constraints of protein pocket on chromophores are the probable reason for moving their dynamic reaction equilibrium forward. On the other hand, photochemical reaction to switch a molecule from one isomer to the other with different geometry and property in a high yield will continue to play a vital role in the synthetic chemistry and material science. Because of the important role of efficient photoisomerization, a biomimetic approach for "seeing" and controlling the photoisomerization is developed by using the technology of aggregation-induced emission (AIE) with supramolecular chemistry. It is revealed that a (Z)-isomer of a 2-ureido-4[1H]-pyrimidinone-containing tetraphenylethene (TPE-UPy) can be photoisomerized into supramolecular polymer form of its (E)-counterpart in chloroform in a high reaction yield of 68.1%. The yield is further enhanced to 100% in THF as aggregates of supramolecular polymers of (E)-TPE-UPy are formed, which completely inhibits the reverse photoreaction to form (Z)-TPE-UPy. In chloroform with organic acid, a mixture of equal amounts of (E)- and (Z)-isomers was obtained due to the disruption of the formation of intermolecular hydrogen bonds. The AIE characteristics of the isomers allow us to directly "see" the "turn-on" photoisomerization process by distinct fluorescence color changes, and the photoisomerization observed here may enable the development of a promising generation of optical power limiting materials.

Easy calibration of the Light Plate Apparatus for optogenetic experiments.

Optogenetic systems use genetically-encoded light-sensitive proteins to control and study cellular processes. As the number and quality of these systems grows, there is an increasing need for user-friendly and flexible hardware to provide programmed illumination to cultures of cells. One platform which satisfies this need for a variety of optogenetic systems and organisms is the Light Plate Apparatus (LPA), which delivers a controlled light dose to each well of a 24-well plate. Experimental reproducibility requires appropriate calibration to produce accurate light doses within individual wells of the LPA and between LPAs. In this study, we present an easy and accurate method for calibrating the LPA. In particular, we: •developed a 3D printed adaptor and MATLAB code to allow rapid measurement of irradiance produced by the LPA and subsequent calibration•provide appropriate code and methodology for generating a standard curve for each LPA•demonstrate the utility and accuracy of this method between users and LPAs.