Effect of one-time placement of the definitive abutment versus multiple healing abutment disconnections and reconnections during the prosthetic phase on radiographic and clinical outcomes: A 12-month randomized clinical trial.

OBJECTIVE: The aim of this investigation was to evaluate the effect on clinical and radiological outcomes of the one-abutment, one-time protocol (test) versus placing the definitive abutment on the day of functional loading after having disconnected and connected three times the healing abutment during the prosthetic phase (control). MATERIALS AND METHODS: Forty patients with 80 implants were randomly allocated to either the test or the control group. Changes in the radiographic marginal bone levels (MBLs), clinical outcomes, prosthetic-related outcomes, and patient-reported outcomes measures (PROMs) were assessed and compared 6 and 12 months after functional loading. RESULTS: Thirty-seven patients with 74 implants were followed at 12 months. A statistically significant bone remodeling was observed in both groups following implant placement. MBLs were significantly greater in the control group at the 6- (-0.13 mm vs. -0.61 mm) and 12-month visits (-0.01 mm vs. -0.53 mm). Bone loss was significantly greater in the control group from surgery to 6 and 12 months and from loading to 6 and 12 months. The abutment height was significantly greater in the test group, however, there were no significant differences in the restorative angle. Similarly, there were no statistically significant differences between groups for the measured clinical variables (probing depth, plaque, and bleeding index) and PROMs. CONCLUSIONS: Disconnecting and reconnecting the healing abutment was associated with significantly higher bone loss after 12 months, as compared to the placement of the definitive abutment at implant installation.

Prospective observational cohort study of the change of the marginal bone crest in relation to the prosthetic abutment height and the peri-implant vertical mucosal thickness at implants positioned subcrestally.

AIM: To evaluate the influence on peri-implant crestal bone loss exerted by the vertical mucosal thickness and the abutment height over 12 months after placement of the restoration on subcrestal implants with change of platform, using a restoration abutment platform smaller than the implant platform. MATERIALS AND METHODS: A total of 99 implants were rehabilitated in the maxillary and mandibular posterior regions. A total of 22 implants were rehabilitated in the maxilla and 77 implants in the mandible, using digitally designed customized abutments with Atlantis weborder software, from the commercial house Dentsply Sirona (Dentsply Sirona S.A., Barcelona, Spain), version 4.6.5, adapting the height to the vertical thickness of the mucosa. Clinical and radiographic monitoring begins during the surgical procedure of placement of the implant and ends 12 months afterwards. Crestal bone loss was evaluated through the Carestream® CS8100 3D radiographic equipment. RESULTS: In all cases, the greatest loss of marginal bone occurred between the day of surgery (Tx) and placement of the rehabilitation (To). The average bone loss between both times was greater when the abutment height and vertical mucosal thickness did not exceed 3 mm. Subsequently, bone loss slowed and stabilized at 12 months. CONCLUSIONS: The minimum abutment height and the vertical mucosal thickness are factors to take into account when minimizing peri-implant marginal bone loss, the abutment height having the greatest importance according to the clinical data obtained.

Does Implant Placement Below the Ridge Reduce Crestal Bone Loss? A Split-Mouth Randomized Controlled Clinical Trial.

Reducing crestal bone loss (CBL) around implants allows for soft tissue stability and long-term success. The aim of the present study was to evaluate the extent of CBL in implants placed with the implant shoulder at the equi-crestal level and 2 mm below the alveolar ridge at 2, 12, 36, and 60 months. A split-mouth randomized controlled clinical trial was conducted by selecting subjects with Kennedy Class IV partial edentulism of the lower jaw. Two implants were inserted, of equal length and diameter, one equi-crestal and the other sub-crestal, in the site corresponding to the lateral incisor. Intraoral periapical radiographs with Rinn centering devices were performed at the time of implant insertion (T0), at 2 (T1), 12 (T2), 36 (T3), and 60 months (T4). Descriptive statistics and the T-test were used, setting the significance to P⩽ 0.05. Twenty-five subjects were recruited, with a mean age of 65 years (SD 9.88, range 42-82). No subject dropped out. A total of 50 implants were inserted, 25 at crestal and 25 sub-crest level. At the 60-month follow-up, no implant or prosthetic failure was recorded. An average loss of -0.81 mm was recorded in the crestal implant group (n.25; SD: 0.40; max-min: -1.6 - -0.1) while in the implants positioned below the crest the average CBL was -0.87mm (n.25; SD: 0.41; max-min: -2 - -0.2); however, the higher CBL in the sub-crestal implant group was not statistically significant (P=0.65). Comparing the mean CBL values of the two groups at the various follow-ups, a greater crestal bone resorption was recorded in sub-crest implants between T0 and T1 (-0.25 vs -0.1) and between T1 and T2 (-0.39 vs -0.23), while in subsequent follow-ups a greater, statistically significant (P=0.01), crestal bone loss was recorded in ridge implants between T3 and T4 (-0.05 vs -0.18). Over time, therefore, the extent of CBL seems to be reduced in implants placed below the crest, with bone retention above the implant shoulder. Ultimately, although the position of the implant shoulder relative to the crestal ridge doesn't affect the CBL, sub-crestal placement is recommended in order to reduce the risk of exposure of the rough surface of the implant.

The effect of one-time abutment placement on clinical and radiographic outcomes: A 5-year randomized clinical trial.

OBJECTIVE: The aim of this study was to evaluate the long-term (5 years) clinical efficacy of the one-abutment one-time protocol (test) versus the standard of care by placing the definitive abutment on the day of the prosthetic delivery (control). MATERIALS AND METHODS: In this study, 39 subjects with 60 implants were randomly allocated to either the test or the control group. Changes in the radiographic interproximal bone levels (DIB), modified sulcus bleeding index, probing depth, modified plaque index, papilla fill (Jemt score), incidence of peri-implantitis and peri-implant mucositis as well as patient-reported outcomes measures (PROMs) were collected and compared at 1, 3 and 5 years. RESULTS: At 5 years, the control group showed a greater, although not statistically significant, change in mean DIB values (0.97 mm vs. 0.53 mm). Regarding the other clinical parameters evaluated, no statistically significant differences were observed between groups at any time point. At 5 years, 51% of the implants presented peri-implant mucositis (25.5% in the control and 23.5% in the test), and only one implant in the test group developed peri-implantitis. CONCLUSIONS: The connection and disconnection of healing abutments during the healing period was not associated with higher long-term bone loss. Clinical outcomes and PROMs were similar between groups.

Multivariate analysis of the effect of keratinized mucosa on peri-implant tissues with platform switching: A retrospective study.

BACKGROUND: In recent years, platform switching implant treatment has been increasing, which is believed to minimize bone loss around the implant after placement. However, there have been no reports on the relationship between keratinized mucosa width (KMW) and bone loss and soft tissue recession in platform switching implants. OBJECTIVE: We evaluated the effect of the KMW on the amount of bone loss and soft tissue recession around a platform switching implant retrospectively using multivariate analysis. MATERIALS AND METHODS: This one-year retrospective study included 91 implants in 48 patients. Age, sex, a history of periodontitis, implant location, oral hygiene status, and the KMW were included as explanatory variables to evaluate bone loss (BL) and buccal gingival height (GH). Generalized estimating equations (GEEs) were used to evaluate the effect of the KMW on platform switching peri-implant tissues. RESULTS: The mean bone loss on the mesial (ΔBLm), distal (ΔBLd), and buccal (ΔBLb) sides of the implant were 0.16 ± 0.27 mm, 0.19 ± 0.34 mm, and 0.24 ± 0.50 mm, respectively, at 1 year after superstructure placement. The mean amount of change of GH (ΔGH) on the buccal side was 0.30 ± 0.47 mm. After correcting for confounders using GEEs, the results suggested that KMW <1.5 mm was a significant factor (P < 0.001) for bone loss over time in ΔBLm, ΔBLd, and ΔBLb. In addition, for soft tissues on the buccal side, KMW <1.5 mm was a significant factor for ΔGH reduction over time (P < 0.001). CONCLUSIONS: Keratinized mucosa width ≥1.5 mm was associated with a higher probability less hard and soft tissue recession around the platform switching implant after 1 year from superstructure placement.

Clinical and Radiographic Outcomes of a New Fully Tapered Implant with the One-Abutment One-Time Approach: In-Line Clinical Case Series with a 1-Year Follow-up.

PURPOSE: To evaluate the bone level changes in a new implant design (fully tapered with platform switching) with the one-abutment one-time protocol after 1 year of loading. MATERIALS AND METHODS: Thirty patients received 1 or 2 implants (6-, 8-, or 10-mm length and 3.5-, 3.75-, or 4.5-mm diameter, bone-level design) to replace one or multiple edentulous sites. Only the mesial implant was assessed. Radiographic, clinical, and esthetic results and the survival and success rates were evaluated 1 year after final loading. RESULTS: At 1 year, no peri-implant bone loss was seen in any of the cases. Mean marginal crestal bone loss between surgery and crown placement was 0.19 ± 0.17 mm (P < .0001). Between surgery and the 1-year follow-up, the mean marginal crestal bone loss was 0.25 ± 0.24 mm (P < .0001). The difference in the modified Plaque Index between 1 year of follow-up and crown placement was significant for in the mesial (0.33 ± 0.54 mm; P = .003) and distal surfaces (0.5 ± 0.73 mm; P = .001). The probing pocket depth was statistically significantly deeper at 1 year than at crown placement at the mesial and distal aspects (average depth = 0.75 mm; P < .0005). No statistically significant differences were found for any other clinical or esthetic parameters. The overall survival and success rates after 1 year were 100%. CONCLUSIONS: The fully tapered, deep-thread, platform-switched implant design placed with the one-abutment one-time protocol demonstrated minimal marginal crestal bone loss and crestal bone stability at 1 year of follow-up.

One-Year Outcomes of Subcrestal Platform-Switched Implants With and Without Sterile Prosthetic Abutments: A Randomized Controlled Trial.

Surface contaminants on customized implant abutments could trigger inflammatory response in the peri-implant tissues. The aim of this randomized controlled study was to assess the radiographic bone changes around implants restored with customized, platform-switched abutments, with and without autoclave treatment, 12 months after definitive restoration. Dental implants were placed 1 mm subcrestally in 64 systemically healthy patients (mean age 63.3 ± 10.0 years, 31 with history of periodontitis) to replace single or multiple missing teeth. According to a randomization list, abutments were subjected to steam and autoclave sterilization (43 implants, test group) or steam cleaning alone (44 implants, control group). Periapical standardized radiographs were taken at the time of implant insertion, prosthetic abutment connection and 12 months after definitive cement-retained restoration. All implants were clinically stable without any sign of infection at the 12-month follow-up. An average marginal bone loss of 0.25 ± 0.19 mm was found in the test group compared to 0.35 ± 0.23 mm in the control group without statistically significant difference, while the percentage of bleeding sites was significantly higher in the control group (8.7 ± 13.1% versus 19.1 ± 19.8%, P = .035). Autoclave treatment of customized abutments would seem to reduce the inflammatory response around subcrestally placed implants.

Clinical and radiographic results of crestal vs. subcrestal placement of implants in posterior areas: A split-mouth randomized controlled clinical trial.

OBJECTIVE: The objective of this study was to evaluate the peri-implant soft tissue and marginal bone loss (MBL) around implants with platform-switching and internal conical connection placed at crestal and subcrestal levels in posterior areas. MATERIALS AND METHODS: Nineteen partially edentulous patients with at least two adjacent missing teeth in posterior areas unilaterally or bilaterally were included. Forty-two implants were placed randomly at the crestal or subcrestal (1 mm) level in a split-mouth design. Implant-supported fixed dental prostheses with screw retention were delivered after 4 months of healing. Clinical and radiological measurements were performed at implant placement (T0), restoration delivery (T1), and 1-year follow-up after loading (T2). MBL was calculated as the change in distance from the implant-abutment interface to the first radiographically visible bone-implant contact. A repeated-measures mixed ANOVA followed by a paired Student's t-test with the Bonferroni correction was used for statistical analysis. p < 0.05 was considered statistically significant. RESULTS: Eighteen patients with thirty-eight implants completed the study at T2. The MBL was lower in the subcrestal group than in the crestal group (0.04 ± 0.08 vs. 0.17 ± 0.17 mm, p = 0.004). The peri-implant probing depth (PD) was 2.31 ± 0.48 mm in the subcrestal group and 1.92 ± 0.43 mm in the crestal group; this difference was statistically significant (p = 0.002). Intragroup comparison showed no significant differences in MBL, or PD around the crestal group and subcrestal group from T1 to T2. CONCLUSION: After 1 year of functional loading, subcrestal placement of implants with platform-switching and internal conical connection showed lower MBL and was associated with greater PD and peri-implant soft tissue height than implants placed at the crestal level.

Maxillary labial peri-implant hard and soft tissue alteration observed on cross-sectional dimension: a 2-year prospective observational study.

OBJECTIVES: To evaluate how peri-implant hard and soft tissue height (BH, MH) alter after final prostheses placement related to labial hard and soft tissue thickness (BW, MW). MATERIALS AND METHODS: Forty-five platform-switched implants were classified into four groups according to BW and MW: type 1 (thick BW and thick MW), type 2 (thick BW and thin MW), type 3 (thin BW and thick MW), type 4 (thin BW and thin MW). Tissue resorption was evaluated on cone-beam CT images taken at final prostheses placement, at 1-year follow-up, and at 2-year follow-up. Kruskal-Wallis test and post hoc Mann-Whitney test were applied; significance was set to 0.05. RESULTS: BH resorption was 0.13 ± 0.12 mm in type 1, 0.26 ± 0.17 mm in type 2, 0.09 ± 0.09 mm in type 3, 0.94 ± 0.19 mm in type 4. Differences between type 1 and 4, type 2 and 4, and type 3 and 4 were statistically significant (p < 0.001, p = 0.005, p < 0.001, respectively). MH resorption was 0.10 ± 0.09 mm in type 1, 0.36 ± 0.16 mm in type 2, 0.12 ± 0.12 mm in Type 3, 0.79 ± 0.23 mm in type 4. Differences between type 1 and 2, type 1 and 4, type 2 and 3, type 2 and 4 and type 3 and 4 were statistically significant (p < 0.001). CONCLUSIONS: Significantly less BH/MH resorption occurs around implants with thick BW/MW than those with thin BW/MW in 2 years. Implants with thick peri-implant soft tissue resulted in significantly less tissue resorption in second year after final prostheses placement.

[Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching].

OBJECTIVE: To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention. METHODS: By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s. RESULTS: At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm. CONCLUSION: When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

In Silico Mechanical Effort Analysis of the All-On-4 Design Performed With Platform-Switching Distal Short Dental Implants.

Short dental implants with platform matching connection have been used for the rehabilitation of atrophic jaws whenever standard-length dental implants cannot be placed without prior bone augmentation. Yet, there remains a lack of data regarding the risk of technical failures when the all-on-4 configuration is performed in atrophic jaws with platform-switching distal short dental implants. Thus, the current study used the finite element method to evaluate the mechanical behavior at the level of the prosthetic components of the all-on-4 concept performed in atrophic mandible using short-length distal implants with platform switching (PSW) connection. Three models of the all-on-4 configuration were generated in human atrophic mandibles. The geometric models consisted of PSW connection tilted standard (AO4T; θ = 30 deg; 11 mm-length), straight standard (AO4S; θ = 0 deg; 11 mm-length) and straight short (AO4Sh; θ = 0 deg; 8 mm-length) distal implants. A resultant force of 300 N was performed obliquely in the left side and posterior region of the prosthetic bar. The von Mises equivalent stress (σvm) and maximum and minimum principal stresses (σmax and σmin) were performed at level of the prosthetic components/implants and peri-implant bone crest, respectively. The general displacement of the models was also evaluated. The stress analysis was performed on the side of load application. The AO4S configuration showed the lowest values of σvm in the mesial left (ML) and distal left (DL) abutments (37.53 MPa and 232.77 MPa, respectively) and dental implants (91.53 MPa and 231.21 MPa, respectively). The AO4Sh configuration showed the highest values of σvm in the bar screw (102.36 MPa), abutment (117.56 MPa), and dental implant (293.73 MPa) of the ML area. Among the models, the highest values of σmax and σmin were noticed in the peri-implant bone crest of the AO4T design (131.48 MPa and 195.31 MPa, respectively). All models showed similar values of general displacements, which were concentrated in the mandible symphysis. The all-on-4 configurations designed with PSW connection and tilted standard (AO4T; θ = 30 deg; 11 mm-length), straight standard (AO4S; θ = 0 deg; 11 mm-length) or straight short (AO4Sh; θ = 0 deg; 8 mm-length) distal implants were not associated with higher odds of technical failures. The AO4Sh design may be a promising option for the prosthetic rehabilitation of atrophic jaws.

Up to a 15-Year Survival Rate and Marginal Bone Resorption of 1780 Implants with or without Microthreads: A Multi Center Retrospective Study.

The effect of microthreads at the implant neck on the amount of marginal bone resorption is controversial. This multicenter retrospective study compared the implant survival rate and amount of marginal bone resorption between two platform-switching internal connection implant systems with or without microthreads. Patient-related (age and sex), surgery-related (implant installation site, type, diameter, and length), and prosthesis-related (prosthesis type) data were collected from patient charts from the implant placement surgery to the final recall visit. A total of 1780 implants, including 1379 with microthreads and 401 without microthreads, were placed in 804 patients. For implants with and without microthreads, the longest follow-up period after prosthesis delivery was 15 and 6 years, respectively. Twenty implants failed during the 15-year follow-up period (98.8% survival rate) due to failed osseointegration, peri-implantitis, implant fractures, and non-functioning implants. The mean marginal bone loss was < 0.1 mm for both implant systems at the 1-year follow-up and 0.18 mm and 0.09 mm at the 4-year follow-up for implants with and without microthreads, respectively, without statistical significance. Microthreads did not significantly affect the amount of marginal bone loss or the implant survival rate for implants with an internal connection with a platform-switching design.

Three-dimensional finite element analysis of cement flow in abutment margin-crown platform switching / 北京大学学报(医学版)

OBJECTIVE@#To analyze the cement flow in the abutment margin-crown platform switching structure by using the three-dimensional finite element analysis, in order to prove that whether the abutment margin-crown platform switching structure can reduce the inflow depth of cement in the implantation adhesive retention.@*METHODS@#By using ANSYS 19.0 software, two models were created, including the one with regular margin and crown (Model one, the traditional group), and the other one with abutment margin-crown platform switching structure (Model two, the platform switching group). Both abutments of the two models were wrapped by gingiva, and the depth of the abutment margins was 1.5 mm submucosal. Two-way fluid structure coupling calculations were produced in two models by using ANSYS 19.0 software. In the two models, the same amount of cement were put between the inner side of the crowns and the abutments. The process of cementing the crown to the abutment was simulated when the crown was 0.6 mm above the abutment. The crown was falling at a constant speed in the whole process spending 0.1 s. Then we observed the cement flow outside the crowns at the time of 0.025 s, 0.05 s, 0.075 s, 0.1 s, and measured the depth of cement over the margins at the time of 0.1 s.@*RESULTS@#At the time of 0 s, 0.025 s, 0.05 s, the cements in the two models were all above the abutment margins. At the time of 0.075 s, in Model one, the gingiva was squeezed by the cement and became deformed, and then a gap was formed between the gingiva and the abutment into which the cement started to flow. In Model two, because of the narrow neck of the crown, the cement flowed out from the gingival as it was pressed by the upward counterforce from the gingival and the abutment margin. At the time of 0.1 s, in Model one, the cement continued to flow deep inside with the gravity force and pressure, and the depth of the cement over the margin was 1 mm. In Model two, the cement continued to flow out from the gingival at the time of 0.075 s, and the depth of the cement over the margin was 0 mm.@*CONCLUSION@#When the abutment was wrapped by the gingiva, the inflow depth of cement in the implantation adhesive retention can be reduced in the abutment margin-crown platform switching structure.

Peri-implant bone level assessment of early loaded dental implants submitted to different prosthetic protocols: a case report / Avaliação do nível ósseo peri-implantar de implantes dentários com carregamento antecipado submetidos a protocolos protéticos diferentes: relato de caso

Aim: The present split-mouth case report aims to describe the clinical and radiographic long-term outcomes of the implant rehabilitation of two mandibular premolars in which the digital workflow was used to apply different prosthetic protocols. Case description: A female 42-year-old patient with the absence of both mandibular second premolars was submitted to guided surgery for the placement of platform-switching Grand Morse connection implants. Digital workflow was used for implant and prosthetic planning, applying early loading protocol 21 days after surgery. The implant on the right side received the final abutment at the time of surgery (without loading), whereas the implant on the left side had a healing abutment placed, which was replaced by a temporary abutment and then by a final abutment. Two months after surgery, both implants had final ceramic restorations delivered. The patient was followed clinically and radiographically for 30 months, presenting excellent hard and soft tissue outcomes, with bone level changes lower than 2mm for both implants. Conclusion: The use of digital workflow and early loading, made the present implant-supported rehabilitation predictable, safe and time-efficient, resulting in total patient satisfaction. Peri-implant bone level was observed to be stable after early loading protocol for both platform-switching connection implants inserted, despite the prosthetic protocol applied.(AU)

Objetivo: O presente relato de caso de boca dividida tem como objetivo descrever os resultados clínicos e radiográficos a longo prazo da reabilitação com implante de dois pré-molares inferiores em que o fluxo de trabalho digital foi usado para aplicar os conceitos de "one abutment-one time" em uma das reabilitações e troca de componente no outro. Descrição do caso: Paciente do sexo feminino, 42 anos, com ausência de ambos os segundos pré-molares inferiores, foi submetida à cirurgia guiada para colocação de implantes de conexão Grand Morse plataforma-switching. Foi utilizado fluxo de trabalho digital para planejamento de implante e prótese, aplicando protocolo de carga antecipada 21 dias após a cirurgia. O implante do lado direito recebeu o componente protético definitivo no momento da cirurgia (sem carga), enquanto o implante do lado esquerdo recebeu um cicatrizador, que foi substituído por um pilar provisório e depois por um componente definitivo. Dois meses após a cirurgia, ambos os implantes tiveram restaurações cerâmicas finais entregues. A paciente foi acompanhada clínica e radiograficamente por 30 meses, apresentando excelentes resultados de tecidos duros emoles, com alterações do nível ósseo inferiores a 2mm para ambos os implantes. Conclusão: O fluxo de trabalho digital e carregamento precoce, tornou a presente reabilitação implantossuportada previsível, segura e eficiente em termos de tempo, resultando em total satisfação do paciente. O nível ósseo peri-implantar foi observado como estável após o protocolo de carregamento inicial para ambos os implantes de conexão plataforma-switching inseridos, independente do protocolo protético aplicado. (AU)

Impact of Platform Switched Implants on Marginal Bone Level in Mandibular Overdentures: A Six-Year Follow-Up Longitudinal Study.

Purpose: To evaluate the impact of the platform-switched implant on marginal bone loss (MBL) and the probing pocket depth (PPD) in patients wearing mandibular overdenture. Patients and Methods: This longitudinal study included 40 completely edentulous patients aged 51-64 years. All patients received complete dentures and were distributed into two groups randomly; 20 patients each. The first group GI received two platform switched implants; however, the 2nd group GII received two platform matched implants (3.6 × 11.5 mm) in the canine region of the mandible. The radiographic evaluations were carried out every year for six years, whereas probing pocket depth was evaluated every six months for 72 months for both groups. The data were analyzed by repeated ANOVA, Friedman's, and Student's t-test. Results: This study included 36 patients; 56 ± 3.6 years was the mean age; 17 females (47%) and 19 males (53%) completed the study. Statistically significant differences were observed in MBL and PPD in each of GI and GII after 6 years, p ≤ 0.05. Between GI and GII after 6 years, a statistically insignificant difference was detected in MBL or PPD, p ≥ 0.05, except in PPD at loading, 2 and 6 years, p ≤ 0.05. Conclusion: Time positively affected MBL and PPD in platform switched and matched implants retained mandibular overdentures. Platform switching influences probing pocket depth in implants retained mandibular overdentures.

Effect of the prosthetic index on stress distribution in Morse taper connection implant system and peri-implant bone: a 3D finite element analysis.

BACKGROUND: The combination of a prosthetic index with Morse taper connection was developed, with the purpose of making prosthetic procedures more precise. However, the presence of the index may compromise the mechanical performance of the abutment. The aim of this study is to evaluate the effect of prosthetic index on stress distribution in implant-abutment-screw system and peri-implant bone by using the 3D finite element methodology. METHODS: Two commercial dental implant systems with different implant-abutment connections were used: the Morse taper connection with platform switching (MT-PS) implant system and the internal hex connection with platform matching (IH-PM) implant system. Meanwhile, there are two different designs of Morse taper connection abutment, namely, abutments with or without index. Consequently, three different models were developed and evaluated: (1) MT-PS indexed, (2) MT-PS non-indexed, and (3) IH-PM. These models were inserted into a bone block. Vertical and oblique forces of 100 N were applied to each abutment to simulate occlusal loadings. RESULTS: For the MT-PS implant system, the maximum stress was always concentrated in the abutment neck under both vertical and oblique loading. Moreover, the maximum von Mises stress in the neck of the MT-PS abutment with index even exceed the yield strength of titanium alloy under the oblique loading. For the IH-PM implant system, however, the maximum stress was always located at the implant. Additionally, the MT-PS implant system has a significantly higher stress level in the abutment neck and a lower stress level around the peri-implant bone compared to the IH-PM implant system. The combined average maximum stress from vertical and oblique loads is 2.04 times higher in the MT-PS indexed model, and 1.82 times for the MT-PS non-indexed model than that of the IH-PM model. CONCLUSIONS: MT-PS with index will cause higher stress concentration on the abutment neck than that of without index, which is more prone to mechanical complications. Nevertheless, MT-PS decreases stress within cancellous bone and may contribute to limiting crestal bone resorption.

Influence of the loading protocol and platform switching in two-implant bar-retained overdentures: 3-year results from a randomized controlled equivalence clinical trial.

OBJECTIVES: To test the null hypothesis that vertical peri-implant bone level alterations (ΔIBL) are equivalent in immediately (IL) and 3-month post-placement (DL) loaded implants in mandibular implant overdentures (IODs) on two implants. MATERIALS AND METHODS: Thirty-two patients receiving two interforaminal implants, one with a platform-switched and one with a platform-matching abutment were randomly assigned to the IL or DL group (allocation ratio 1:1). All implants were primarily splinted with chairside-customized bars, converting the existing removable complete dentures to IODs. Standardized radiographs were recorded. The influence of the loading protocol (IL vs. DL), implant platform (platform switched vs. platform matching), implant site (43 vs. 33), participant age (≤65 vs. >65 years), and definition of baseline (implant placement vs. implant loading) were analyzed, applying linear regression analyses (α = 0.05). The equivalence range was [-0.4; 0.4]. RESULTS: Three participants of the IL group were lost during follow-up. The overall mean ΔIBL was -0.96 ± 0.89 mm. The ΔIBL was equivalent in terms of the implant platform and implant site but not in terms of participant age (in favor of more elderly participants) and the loading protocol. A significantly smaller ΔIBL was observed in the IL when the baseline was considered to be implant placement (p = .017), but not when it was considered to be implant loading (p = .084). CONCLUSION: Immediate loading of primary-splinted implants in two-implant bar-retained overdentures, seems beneficial relative to loading 3 months post-placement, with respect to ΔIBL. The ΔIBL were equivalent in terms of platform switching.

Microgap and microleakage of a hybrid connection platform-switched implant system in the absence or presence of a silicone-based sealing agent.

The present study aims to characterize, for the first time, the microgap and bacterial microleakage of a platform-switched implant system with hybrid connection, screwed at distinct torque values (manufacturer recommended torque-25 N cm-and a reduced torque-5 N cm-mimicking the long-term functional use), in the absence or presence of a silicon-based sealing agent. Microgap was determined through scanning electron microscopy and bacterial microleakage was evaluated in vitro, upon Enterococcus faecalis colonization of the system. The sealing efficacy was evaluated in the absence or presence of a commercially available silicon-based sealer. The cytotoxicity of the sealer was further addressed in vitro, with a fibroblastic cell line, in accordance with reference standards. A low microgap of the implant system was verified, regardless of the applied torque load-maximal values ranged around 0.25 and 1.25 µm, for 25 and 5 N cm torques, respectively. No bacterial microleakage was reported at 25 N cm, while at 5 N cm, leakage was verified on 38% of the samples. The application of a silicon-based sealer-with an adequate cytocompatible profile-was effective on preventing the bacterial microleakage on the assayed experimental setting. The assayed platform-switched implant system with hybrid connection presented a low interfacial misfit and an effective sealing capability at manufacturer recommended torque. Despite the increased microleakage at low torque conditions, the application of a cytocompatible silicon-based sealing agent restored the sealing effectiveness of the system. The use of a silicon-based sealing agent can assist on the maintenance of the sealing effectiveness even at low torque conditions.

Behavior of Soft Tissue around Platform-Switched Implants and Non-Platform-Switched Implants: A Comparative Three-Year Clinical Study.

To verify the influence of platform-switching (PS) on soft tissue behavior by comparing the soft tissue stability around implants with and without PS, during three years of follow-up. The study included patients treated with fixed dentures supported by implants with an internal connection. The radiographic distance between the first bone-to-implant contact (FBIC) and the implant shoulder was assessed. Additionally, the presence of keratinized facial mucosa and the prosthetic crown height (TH) were monitored for three years from the delivery of the definitive crown. These parameters were measured for two different groups: platform-switched implants in the PS group and non-platform-switched (NPS) implants in the NPS group. Seventy-seven implants were considered in the statistical analysis. After three years, the overall FBIC mean value was 0.31 ± 1.00 mm. However, the mean FBIC was 0.66 ± 0.97 mm for the NPS group and -0.05 ± 0.91 mm for the PS group. Moreover, a mean recession of 0.54 ± 1.39 mm was measured for the NPS group, whereas a mean coronal migration of 0.17 ± 0.95 mm was measured for the PS group. A significant correlation was also found between the presence of PS and ΔTH (p ≤ 0.01) over the three years of follow-up. The absence or presence of platform-switching would appear to affect the tendency of the gingival buccal margin towards recession or creeping. Additionally, implant-abutment platform-switching seems to help prevent peri-implant soft tissue recession over time when compared to implants without PS.

Bone-level changes around implants with 1- or 3-mm-high abutments and their relation to crestal mucosal thickness: A 1-year randomized clinical trial.

AIM: To evaluate 1-year bone-level changes around subcrestal platform-switching implants with 1 or 3 mm definitive abutments. The influence of mucosal thickness on bone-level alterations was further analysed. MATERIALS AND METHODS: Implants were placed in the posterior sextants and positioned 1.5 mm subcrestally with an abutment of 1 or 3 mm height. Final restorations were delivered after 16 weeks. Radiographic measurements of inter-proximal bone level were the primary outcome and were adjusted by vertical mucosal thickness. Peri-implant clinical conditions and resonance frequency analysis were also compared. RESULTS: A total of 65 subjects with 99 implants were analysed. The overall 1-year implant survival rate between the 1- and 3-mm groups was 96.4% and 94.4%, respectively. Statistically significant lower inter-proximal marginal bone-level changes were observed in the 3-mm group (1 mm: -0.17 ± 0.02 mm at mesial and -0.21 ± 0.02 mm distal; 3 mm: -0.03 ± 0.02 mm at mesial and -0.03 ± 0.02 mm and distal; mesial: p = .001; distal: p < .001). Initial vertical mucosal thickness was not correlated with inter-proximal marginal bone loss. CONCLUSIONS: Subcrestal implants with 3-mm abutment were associated with minimal inter-proximal bone loss. Independent of the abutment height, crestal mucosal thickness was not correlated with bone loss.