A comprehensive review on application of atomic force microscopy in Forensic science.

The primary objective of forensic investigation of a case is to recognize, identify, locate, and examine the evidence. Microscopy is a technique that provides crucial information for resolving a case or advancing the investigation process by analyzing the evidence obtained from a crime scene. It is often used in conjunction with suitable analytical techniques. Various microscopes are employed; scanning probe microscopes are available in diverse forensic analyses and studies. Among these, the atomic force microscope (AFM) is the most commonly used scanning probe technology, offering a unique morphological and physico-chemical perspective for analyzing multiple pieces of evidence in forensic investigations. Notably, it is a non-destructive technique capable of operating in liquid or air without complex sample preparation. The article delves into a detailed exploration of the applications of AFM in the realms of nanomechanical forensics and nanoscale characterization of forensically significant samples.

Anti-IgG Doped Melanin Nanoparticles Functionalized Quartz Tuning Fork Immunosensors for Immunoglobulin G Detection: In Vitro and In Silico Study.

The quartz tuning fork (QTF) is a promising instrument for biosensor applications due to its advanced properties such as high sensitivity to physical quantities, cost-effectiveness, frequency stability, and high-quality factor. Nevertheless, the fork's small size and difficulty in modifying the prongs' surfaces limit its wide use in experimental research. Our study presents the development of a QTF immunosensor composed of three active layers: biocompatible natural melanin nanoparticles (MNPs), glutaraldehyde (GLU), and anti-IgG layers, for the detection of immunoglobulin G (IgG). Frequency shifts of QTFs after MNP functionalization, GLU activation, and anti-IgG immobilization were measured with an Asensis QTF F-master device. Using QTF immunosensors that had been modified under optimum conditions, the performance of QTF immunosensors for IgG detection was evaluated. Accordingly, a finite element method (FEM)-based model was produced using the COMSOL Multiphysics software program (COMSOL License No. 2102058) to simulate the effect of deposited layers on the QTF resonance frequency. The experimental results, which demonstrated shifts in frequency with each layer during QTF surface functionalization, corroborated the simulation model predictions. A modelling error of 0.05% was observed for the MNP-functionalized QTF biosensor compared to experimental findings. This study validated a simulation model that demonstrates the advantages of a simulation-based approach to optimize QTF biosensors, thereby reducing the need for extensive laboratory work.

Real-time monitoring of dephosphorylation process of phosphopeptide and rapid assay of PTP1B activity based on a 100 MHz QCM biosensing platform.

The misregulation of protein phosphatases is a key factor in the development of many human diseases, notably cancers. Here, based on a 100 MHz quartz crystal microbalance (QCM) biosensing platform, the dephosphorylation process of phosphopeptide (P-peptide) caused by protein tyrosine phosphatase 1B (PTP1B) was monitored in real time for the first time and PTP1B activity was assayed rapidly and sensitively. The QCM chip, coated with a gold (Au) film, was used to immobilized thiol-labeled single-stranded 5'-phosphate-DNAs (P-DNA) through Au-S bond. The P-peptide, specific to PTP1B, was then connected to the P-DNA via chelation between Zr4+ and phosphate groups. When PTP1B was injected into the QCM flow cell where the P-peptide/Zr4+/MCH/P-DNA/Au chip was placed, the P-peptide was dephosphorylated and released from the Au chip surface, resulting in an increase in the frequency of the QCM Au chip. This allowed the real-time monitoring of the P-peptide dephosphorylation process and sensitive detection of PTP1B activity within 6 min with a linear detection range of 0.01-100 pM and a detection limit of 0.008 pM. In addition, the maximum inhibitory ratios of inhibitors were evaluated using this proposed 100 MHz QCM biosensor. The developed 100 MHz QCM biosensing platform shows immense potential for early diagnosis of diseases related to protein phosphatases and the development of drugs targeting protein phosphatases.

Facile Synthesis and Properties of Highly Porous Quartz Fiber-Reinforced Phenolic Resin Composites with High Strength.

Lightweight and high-strength insulation materials have important application prospects in the aerospace, metallurgical, and nuclear industries. In this study, a highly porous silica fiber reinforced phenolic resin matrix composite was prepared by vacuum impregnation and atmospheric drying using quartz fiber needled felt as reinforcement and anhydrous ethanol as a pore-making agent. The effects of curing agent content on the structure, composition, density, and thermal conductivity of the composite were studied. The mechanical properties of the composite in the xy direction and z direction were analyzed. The results showed that this process can also produce porous phenolic resin (PR) with a density as low as 0.291 g/cm3, where spherical phenolic resin particles are interconnected to form a porous network structure with a particle size of about 5.43 µm. The fiber-reinforced porous PR had low density (0.372~0.397 g/cm3) and low thermal conductivity (0.085~0.095 W/m·K). The spherical phenolic resin particles inside the composite were well combined with the fiber at the interface and uniformly distributed in the fiber lap network. The composite possessed enhanced mechanical properties with compressive strength of 3.5-5.1 MPa in the xy direction and appeared as gradual compaction rather than destruction as the strain reached 30% in the z direction. This research provides a lightweight and high-strength insulation material with a simple preparation process and excellent performance.

A Hydration Model to Evaluate the Properties of Cement-Quartz Powder Hybrid Concrete.

Although quartz powder is a common concrete filling material, the importance and originality of this study lies in the development of a hydration model for quartz powder-cement binary mixtures and the adoption of this model to predict the development of concrete material properties. The purpose of this study is to use this model to promote the material design of environmentally friendly concrete and to elucidate the relationships in the development of the various properties of quartz powder concrete. The method used in this study was as follows: The parameters of the hydration model were obtained through seven days of hydration heat experiments. The hydration heat up to 28 days was also calculated, and the various properties of the concrete were predicted from the heat of hydration. The main findings of this study were as follows: (1) The ultimate hydration heat released per gram of cement for the different quartz powder substitution rates and quartz powder particle fineness was the same, at 390.145 J/g cement, as was the shape index of the hydration model at -1.003. (2) Moreover, through the model calculations, we found that, at the twenty-eighth day of the curing period for the quartz powder specimens with different quartz powder substitution amounts and different fineness, the reaction level of the cement was similar, at 0.963, as were the values of the cumulative heat of hydration, with both at 375.5 J/g cement. (3) The model showed that, in the late stage (28 days) of hydration for quartz powders of different fineness and when the substitution amount was the same, the cumulative heat of hydration over 28 days was similar. (4) The properties of concrete were evaluated using the calculated hydration heat. Overall, the predictive performance of the power and linear functions was similar, with no significant differences being found.

The Force-Frequency Characteristics of Quartz Wafers under a Cantilever Beam Structure.

This study investigated the force-frequency characteristics of quartz wafers inside a cantilever beam frame. Firstly, the force-frequency coefficient formula of quartz wafers with fixed ends under axial force was analyzed. Firstly, the formula for the force-frequency coefficient of quartz wafers with fixed ends under axial force was analyzed. A force-frequency coefficient formula suitable for cantilever beam structures was derived by considering the changes in surface stress and stiffness of quartz wafers with fixed ends and one end under force on the other. Subsequently, the formula's accuracy was verified by experiments, and the accuracy was more than 92%. In addition, strain simulation analysis was performed on three different shapes of quartz wafers, and experimental verification was carried out on two of them. The results revealed that trapezoidal quartz wafers and cantilever beam structures exhibited superior stress distribution to rectangular chips. Furthermore, by positioning electrodes at various locations on the surface of the quartz chip, it was observed that, as the electrodes moved closer to the fixed end, the force-frequency coefficient of the rectangular quartz chip increased, along with an increase in chip strain under the cantilever structure. In summary, this study provides a new approach for designing cantilever quartz resonator sensors in the future.

Influence of Front-End Electronics on Metrological Performance of QCM Systems.

Quartz Crystal Microbalances (QCMs) are versatile sensors employed in various fields, from environmental monitoring to biomedical applications, owing mainly to their very high sensitivity. However, the assessment of their metrological performance, including the impact of conditioning circuits, digital processing algorithms, and working conditions, is a complex and novel area of study. The purpose of this work is to investigate and understand the measurement errors associated with different QCM measurement techniques, specifically focusing on the influence of conditioning electronic circuits. Through a tailored and novel experimental setup, two measurement architectures-a Quartz Crystal Microbalance with dissipation monitoring (QCM-D) system and an oscillator-based QCM-R system-were compared under the same mechanical load conditions. Through rigorous experimentation and signal processing techniques, the study elucidated the complexities of accurately assessing QCM parameters, especially in liquid environments and under large mechanical loads. The comparison between the two different techniques allows for highlighting the critical aspects of the measurement techniques. The experimental results were discussed and interpreted based on models allowing for a deep understanding of the measurement problems encountered with QCM-based measurement systems. The performance of the different techniques was derived, showing that while the QCM-D technique exhibited higher accuracy, the QCM-R technique offered greater precision with a simpler design. This research advances our understanding of QCM-based measurements, providing insights for designing robust measurement systems adaptable to diverse conditions, thus enhancing their effectiveness in various applications.

Luminescence, XPS and Raman of crystalline quartz affected to high pressure by detonation.

The Raman spectra, x-ray photoelectron spectroscopy (XPS), and x-ray excited luminescence spectra of crystalline quartz samples subjected to different pressure levels through detonation were compared with the spectra of the original samples. In the samples under study, the luminescence of a self-trapped exciton (STE) was analyzed, which, when excited by x-rays, has a high energy yield (∼20%) in crystallineα-quartz not treated by detonation. The deviations of the luminescence spectrum are small in the pressure range from 9 to 27 GPa relative to untreated samples, which means the presence of crystalline quartz grains. A sharp change in the spectrum occurs for the sample subjected to a pressure of 34 GPa. The STE band practically disappeared and a band appeared at 350 nm. This band appears in thermally stimulated luminescence (in contrast to the STE band, which is not observed at all in thermally stimulated luminescence) and, therefore, can be attributed to some defects arising due to high pressure. This luminescence is not similar to the luminescence of a stishovite single crystal, but analysis of the XPS spectra suggests the formation of non-crystalline stishovite in detonated samples. In the Raman scattering spectra, a single sharp line at 465 cm-1, characteristic ofα-quartz, was observed in the samples after detonation pressure for the remaining small crystal grains. This line decreased greatly for the sample subjected to a pressure of 34 GPa. Against the structureless background of exposed samples of 'poor' optical quality, other Raman bands did not appear. It can be assumed that there are very broad bands of Raman scattering caused by the amorphization of stishovite under high detonation pressure. Amorphization explains the absence of luminescence, similar to the stishovite crystal.

Stiffness calibration of qPlus sensors at low temperature through thermal noise measurements.

Non-contact atomic force microscopy (nc-AFM) offers a unique experimental framework for topographical imaging of surfaces with atomic and/or sub-molecular resolution. The technique also permits to perform frequency shift spectroscopy to quantitatively evaluate the tip-sample interaction forces and potentials above individual atoms or molecules. The stiffness of the probe, k, is then required to perform the frequency shift-to-force conversion. However, this quantity is generally known with little precision. An accurate stiffness calibration is therefore mandatory if accurate force measurements are targeted. In nc-AFM, the probe may either be a silicon cantilever, a quartz tuning fork (QTF), or a length extensional resonator (LER). When used in ultrahigh vacuum (UHV) and at low temperature, the technique mostly employs QTFs, based on the so-called qPlus design, which actually covers different types of sensors in terms of size and design of the electrodes. They all have in common a QTF featuring a metallic tip glued at the free end of one of its prongs. In this study, we report the stiffness calibration of a particular type of qPlus sensor in UHV and at 9.8 K by means of thermal noise measurements. The stiffness calibration of such high-k sensors, featuring high quality factors (Q) as well, requires to master both the acquisition parameters and the data post-processing. Our approach relies both on numerical simulations and experimental results. A thorough analysis of the thermal noise power spectral density of the qPlus fluctuations leads to an estimated stiffness of the first flexural eigenmode of ≃2000 N/m, with a maximum uncertainty of 10%, whereas the static stiffness of the sensor without tip is expected to be ≃3300 N/m. The former value must not be considered as being representative of a generic value for any qPlus, as our study stresses the influence of the tip on the estimated stiffness and points towards the need for the individual calibration of these probes. Although the framework focuses on a particular kind of sensor, it may be adapted to any high-k, high-Q nc-AFM probe used under similar conditions, such as silicon cantilevers and LERs.

Etching Rate Analysis Model Based on Quartz Bond Angle Characteristics.

This paper proposes a method for classifying crystal planes based on the bond angle characteristics of quartz unit cells and constructs an etch rate model for quartz crystal planes at both macro and micro scales. By omitting oxygen atoms from the quartz cell structure, a method based on bond angle characteristics was established to partition the atomic arrangement of the crystal surface. This approach was used to analyze the etching processes of typical quartz crystal planes (R, r, m, and (0001)), approximating the etching process of crystals as a cyclic removal of certain bond angle characteristics on the crystal planes. This led to the development of an etch rate model based on micro-geometric parameters of crystal planes. Additionally, using the proposed bond angle classification method, the common characteristics of atomic configurations on the crystal plane surfaces within the X_cut type were extracted and classified into seven regions, further expanding and applying the etch rate model. The computational results of this model showed good agreement with experimental data, indicating the rationality and feasibility of the proposed method. These also provide a theoretical basis for understanding the microstructural changes during quartz-based MEMS etching processes.

Size-Effect-Based Dimension Compensations in Wet Etching for Micromachined Quartz Crystal Microstructures.

Microfabrication technology with quartz crystals is gaining importance as the miniaturization of quartz MEMS devices is essential to ensure the development of portable and wearable electronics. However, until now, there have been no reports of dimension compensation for quartz device fabrication. Therefore, this paper studied the wet etching process of Z-cut quartz crystal substrates for making deep trench patterns using Au/Cr metal hard masks and proposed the first quartz fabrication dimension compensation strategy. The size effect of various sizes of hard mask patterns on the undercut developed in wet etching was experimentally investigated. Quartz wafers masked with initial vias ranging from 3 µm to 80 µm in width were etched in a buffered oxide etch solution (BOE, HF:NH4F = 3:2) at 80 °C for prolonged etching (>95 min). It was found that a larger hard mask width resulted in a smaller undercut, and a 30 µm difference in hard mask width would result in a 17.2% increase in undercut. In particular, the undercuts were mainly formed in the first 5 min of etching with a relatively high etching rate of 0.7 µm/min (max). Then, the etching rate decreased rapidly to 27%. Furthermore, based on the etching width compensation and etching position compensation, new solutions were proposed for quartz crystal device fabrication. And these two kinds of compensation solutions were used in the fabrication of an ultra-small quartz crystal tuning fork with a resonant frequency of 32.768 kHz. With these approaches, the actual etched size of critical parts of the device only deviated from the designed size by 0.7%. And the pattern position symmetry of the secondary lithography etching process was improved by 96.3% compared to the uncompensated one. It demonstrated significant potential for improving the fabrication accuracy of quartz crystal devices.

Template bacteria-free fabrication of surface imprinted polymer-based biosensor for E. coli detection using photolithographic mimics: Hacking bacterial adhesion.

As one class of molecular imprinted polymers (MIPs), surface imprinted polymer (SIP)-based biosensors show great potential in direct whole-bacteria detection. Micro-contact imprinting, that involves stamping the template bacteria immobilized on a substrate into a pre-polymerized polymer matrix, is the most straightforward and prominent method to obtain SIP-based biosensors. However, the major drawbacks of the method arise from the requirement for fresh template bacteria and often non-reproducible bacteria distribution on the stamp substrate. Herein, we developed a positive master stamp containing photolithographic mimics of the template bacteria (E. coli) enabling reproducible fabrication of biomimetic SIP-based biosensors without the need for the "real" bacteria cells. By using atomic force and scanning electron microscopy imaging techniques, respectively, the E. coli-capturing ability of the SIP samples was tested, and compared with non-imprinted polymer (NIP)-based samples and control SIP samples, in which the cavity geometry does not match with E. coli cells. It was revealed that the presence of the biomimetic E. coli imprints with a specifically designed geometry increases the sensor E. coli-capturing ability by an "imprinting factor" of about 3. These findings show the importance of geometry-guided physical recognition in bacterial detection using SIP-based biosensors. In addition, this imprinting strategy was employed to interdigitated electrodes and QCM (quartz crystal microbalance) chips. E. coli detection performance of the sensors was demonstrated with electrochemical impedance spectroscopy (EIS) and QCM measurements with dissipation monitoring technique (QCM-D).

A novel aptasensor platform for the detection of carcinoembryonic antigen using quartz crystal microbalance.

In this study, a quartz crystal microbalance (QCM) aptasensor for carcinoembryonic antigen (CEA), a well-known biomarker for various cancer types, was reported, utilizing two different aptamers. To achieve this, a nanofilm of 4-mercaptophenyl was electrochemically attached to gold-coated QCM crystal surfaces via the reduction of 4-mercaptobenzenediazonium salt (4 MB-DAT) using cyclic voltammetry. Subsequently, gold nanoparticles (AuNP) were affixed to this structure, and then aptamers (antiCEA1 and antiCEA2) modified with SH-functional ends bound to AuNPs completed the modification. The analytical performance of the CEA sensor was evaluated through simultaneous QCM measurements employing CEA solutions ranging from 0.1 ng/mL to 25 ng/mL. The detection limit (LOD) for CEA was determined to be 102 pg/mL for antiCEA1 and 108 pg/mL for antiCEA2 aptamers. Interday and intraday precision and accuracy tests yielded maximum results of 4.3 and + 3.8, respectively, for both aptasensors, as measured by relative standard deviation (RSD%) and relative error (RE%). The kinetic data of the aptasensors resulted in affinity values (KD) of 0.43 ± 0.14 nM for antiCEA1 and 0.75 ± 0.42 nM for antiCEA2. These values were lower than the reported values of 3.9 nM and 37.8 nM for both aptamers, respectively. The selectivity of the aptasensor was evaluated by measuring the signal changes caused by alpha-fetoprotein (AFP), cancer antigen (CA-125), and vascular endothelial growth factor (VEGF-165) individually and together at a concentration of 500 ng/mL, resulting in a maximum 4.1 % change, which was comparable to precision and accuracy values reported in the literature. After confirming the selectivity of the aptamers, recovery experiments were conducted using spiked commercial serum samples to simulate real samples, and the lowest recovery value obtained was 95.4 %. It was determined that two different aptasensors could be successfully used for the QCM-based detection of CEA in this study.

Characterization of particle exposure during tunnel excavation by tunnel boring machines.

Tunnel boring machines (TBMs) are used to excavate tunnels in a manner where the rock is constantly penetrated with rotating cutter heads. Fine particles of the rock minerals are thereby generated. Workers on and in the vicinity of the TBM are exposed to particulate matter (PM) consisting of bedrock minerals including α-quartz. Exposure to respirable α-quartz remains a concern because of the respiratory diseases associated with this exposure. The particle size distribution of PM and α-quartz is of special importance because of its influence on adverse health effects, monitoring and control strategies as well as accurate quantification of α-quartz concentrations. The major aim of our study was therefore to investigate the particle size distribution of airborne PM and α-quartz generated during tunnel excavation using TBMs in an area dominated by gneiss, a metamorphic type of rock. Sioutas cascade impactors were used to collect personal samples on 3 separate days. The impactor fractionates the dust in 5 size fractions, from 10 µm down to below 0.25 µm. The filters were weighted, and the α-quartz concentrations were quantified using X-ray diffraction (XRD) analysis and the NIOSH 7500 method on the 5 size fractions. Other minerals were determined using Rietveld refinement XRD analysis. The size and elemental composition of individual particles were investigated by scanning electron microscopy. The majority of PM mass was collected on the first 3 stages (aerodynamic diameter = 10 to 0.5 µm) of the Sioutas cascade impactor. No observable differences were found for the size distribution of the collected PM and α-quartz for the 3 sampling days nor the various work tasks. However, the α-quartz proportion varied for the 3 sampling days demonstrating a dependence on geology. The collected α-quartz consisted of more particles with sizes below 1 µm than the calibration material, which most likely affected the accuracy of the measured respirable α-quartz concentrations. This potential systematic error is important to keep in mind when analyzing α-quartz from occupational samples. Knowledge of the particle size distribution is also important for control measures, which should target particle sizes that efficiently capture the respirable α-quartz concentration.

Design of a Transformer Oil Viscosity, Density, and Dielectric Constant Simultaneous Measurement System Based on a Quartz Tuning Fork.

Transformer oil, crucial for transformer and power system safety, demands effective monitoring. Aiming to address the problems of expensive and bulky equipment, poor real-time performance, and single parameter detection of traditional measurement methods, this study proposes a quartz tuning fork-based simultaneous measurement system for online monitoring of the density, viscosity, and dielectric constant of transformer oil. Based on the Butterworth-Van Dyke quartz tuning fork equivalent circuit model, a working mechanism of transformer oil density, viscosity, and dielectric constant was analyzed, and a measurement model for oil samples was obtained. A miniaturized simultaneous measurement system was designed based on a dedicated chip for vector current-voltage impedance analysis for data acquisition and a Savitzky-Golay filter for data filtering. A transformer oil test platform was built to verify the simultaneous measurement system. The results showed that the system has good repeatability, and the measurement errors of density, viscosity, and dielectric constant are lower than 2.00%, 5.50%, and 3.20%, respectively. The online and offline results showed that the system meets the requirements of the condition maintenance system for online monitoring accuracy and real-time detection.

High-Energy Laser Protection Performance of Fibrous Felt-Reinforced Aerogels with Hierarchical Porous Architectures.

Continuous-wave lasers can cause irreversible damage to structured materials in a very short time. Modern high-energy laser protection materials are mainly constructed from ceramic, polymer, and metal constitutions. However, these materials are protected by sacrificing their structural integrity under the irradiation of high-energy lasers. In this contribution, we reported multilayer fibrous felt-reinforced aerogels that can sustain the continuous irradiation of a laser at a power density of 120 MW·m-2 without structural damage. It is found that the exceptional high-energy laser protection performance and the comparable mechanical properties of aerogel nanocomposites are attributed to the unique characteristics of hierarchical porous architectures. In comparison with various preparation methods and other aerogel materials, multilayer fibrous felt-reinforced aerogels exhibit the best performance in high-energy laser protection, arising from the gradual interception and the Raman-Rayleigh scattering cycles of a high-energy laser in the porous aerogels. Furthermore, a near-zero thermal expansion coefficient and extremely low thermal conductivity at high temperature allow the lightweight felt-reinforced aerogels to be applied in extreme conditions. The felt-reinforced aerogels reported herein offer an attractive material that can withstand complex thermomechanical stress and retain excellent insulation properties at extremely high temperature.

Influence of Different Types of Surfactants on the Flotation of Natural Quartz by Dodecylamine.

The synergistic effect among flotation agents is why combined flotation agents exhibit superior performance compared to single flotation agents. This research investigates the influence of three surfactants with different charges of polar groups, sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and octanol, combined with dodecylamine (DDA), on quartz flotation. Through the implementation of flotation tests, bubble-particle adhesion induction time testing, gas-liquid two-phase foam properties testing, and surface tension testing, it is revealed that substituting part of the DDA with these surfactants can either enhance or at least maintain the quartz recovery, affect the adhesion induction time, reduce the surface tension of the flotation system, and change the foaming performance and foam stability, depending on their mole ratio in the combined collector. Compared to DDA alone, combining CTAB or OCT with DDA can significantly increase quartz recovery, while SDS with DDA only yields an approximate recovery. Combining SDS or OCT with DDA can reduce the foam stability, while CTAB with DDA enhances the foam stability. The effect of the combination of surfactants and DDA on the adhesion induction time of quartz grains of different sizes with bubbles is the same; furthermore, there is a negative correlation between the adhesion induction time and the recovery, while the foaming properties and stability of foam are positively correlated with the recovery.

Effects of Curing Defects in Adhesive Layers on Carbon Fiber-Quartz Fiber Bonded Joint Performance.

Due to their mechanical load-bearing and functional wave transmission, adhesively bonded joints of carbon fiber-quartz fiber composites have been widely used in the new generation of stealth aviation equipment. However, the curing defects, caused by deviations between the process environment and the setting parameters, directly affect the service performance of the joint during the curing cycle. Therefore, the thermophysical parameter evolution of adhesive films was analyzed via dynamic DSC (differential scanning calorimeter), isothermal DSC and TGA (thermal gravimetric analyzer) tests. The various prefabricating defects within the adhesive layer were used to systematically simulate the impacts of void defects on the tensile properties, and orthogonal tests were designed to clarify the effects of the curing process parameters on the joints' bonding performance. The results demonstrate that the J-116 B adhesive film starts to cure at a temperature of 160 °C and gradually forms a three-dimensional mesh-bearing structure. Furthermore, a bonding interface between the J-116 B adhesive film and the components to be connected is generated. When the curing temperature exceeds 200 °C, both the adhesive film and the resin matrix thermally degrade the molecular structure. The adhesive strength weakens with an increasing defect area ratio and number, remaining more sensitive to triangle, edge and penetration defects. By affecting the molecular structure of the adhesive film, the curing temperature has a significant impact on the bonding properties; when the curing degree is ensured, the curing pressure directly impacts the adhesive's performance by influencing the morphology, number and distribution of voids. Conversely, the heating rate and heat preservation time have minimal effects on the bonding performance.

Enhancing geomechanical characteristics of calcium sulfoaluminate (CSA) cement-treated soil under low confining pressures.

This study examines the efficacy of employing calcium sulfoaluminate (CSA) cement, an environmentally friendly binder, for enhancing the geomechanical characteristics of sand, particularly under low confining pressure conditions. A series of triaxial consolidated drained tests were performed on sand samples treated with varying content (5, 7, and 10%) of CSA cement and 10% ordinary Portland cement (OPC) under various low confining pressures (50, 100, 200, and 400 kPa). The test findings demonstrated the importance of cement content and confining pressure on the mode of failure, stress-strain and volumetric behavior, failure characteristics, and shear strength parameters of the treated quartz sand. After a curing period of 14 days, samples treated with 10% CSA cement exhibited a remarkable 212% increase in peak deviator stress and an 89% reduction in axial strain at failure, indicating higher initial stiffness compared to untreated samples under a 400 kPa confining pressure. Furthermore, the samples treated with 10% CSA exhibited higher peak deviator stress, initial stiffness, and strength development compared to those treated with 10% OPC. The scanning electron microscopy analysis provides insights into particle breakage and bond degradation processes, which increase with confining pressure in CSA-treated samples. Also, the mode of failure analysis reveals a transition from ductile to slightly brittle behavior with increasing cement content. Notably, the geomechanical properties of the treated material emphasized the significant impact of CSA cement on soil improvement. Thus offering a sustainable alternative for soil improvement in construction projects.

Efficient Fabrication of Quartz Glass Using Laser Coaxial Powder-Fed Additive Manufacturing Approach.

This article investigates a laser-directed energy deposition additive manufacturing (AM) method, based on coaxial powder feeding, for preparing quartz glass. Through synergistic optimization of line deposition and plane deposition experiments, key parameters of laser coaxial powder feeding AM were identified. The corresponding mechanical properties, thermal properties, and microstructure of the bulk parts were analyzed. The maximum mechanical strength of the obtained quartz glass element reached 72.36 ± 5.98 MPa, which is ca. 95% that of quartz glass prepared by traditional methods. The thermal properties of the obtained quartz glass element were also close to those prepared by traditional methods. The present research indicates that one can use laser AM technology that is based on coaxial powder feeding to form quartz glass with high density and good thermodynamic properties. Such quartz glass has substantial potential in, for example, optics and biomedicine.