Characterization of the Chemical Resistance of Two Non-Vulcanized Styrene-Butadiene Rubbers (SBR).

The objective of this series of tests is to characterize the alkali and water resistance of two non-vulcanized formulations based on co-polymerizing styrene-butadiene rubbers (SBR1 and SBR2). The relative merits of the two polymer systems as impregnating agents for alkali-resistant glass reinforcement in cementitious binders are assessed. For this purpose, polymer films were synthesized and then chemically conditioned for up to half a year at temperatures of 23 °C and 50 °C in sodium hydroxide and potassium hydroxide solutions as well as in salt and distilled water. Changes in mass, tensile strength, and material hardness were evaluated to assess the chemical resistance of the two polymer systems. The different test liquids generally led to swelling (increase in mass) and degradation (reduction in mass) of the polymer structures. These two processes occurred simultaneously. The liquid absorption capacity of the SBR1 impregnation system was between 25.05% and 51.60% by weight, depending on the test liquids. In contrast, the SBR2 impregnation system exhibited a lower liquid absorption capacity, with a weight increase from 21.19% to 42.90%. The chemical conditioning resulted in a maximum mass reduction of the polymer structure SBR1 of 8.82% by weight. The polymer SBR2, on the other hand, only lost up to 2.88% by weight. The tensile strengths of the unconditioned samples of the polymer systems SBR1 and SBR2 were 55.49 ± 7.47 N and 80.87 ± 15.96 N, respectively. The test liquids caused a reduction in strength over the storage period which was accelerated by increased temperatures. The loss of strength of the polymer structure SBR2 was lower over the entire conditioning period. In this context, a correlation was found between strength and material hardness. Overall, the polymeric impregnation system SBR2 had a lower liquid absorption capacity and a lower degree of damage caused by the degrading test liquids. Furthermore, the tensile strength was generally higher and more robust over the entire conditioning period. The results of the durability tests indicate that the SBR2 polymer system is more suitable for use in cementitious binders, as it exhibits less degradation of the polymer structure in response to chemical aging processes.

Effluent quality improvement in sequencing batch reactor-based wastewater treatment processes using advanced control strategies.

The treatment of wastewater is highly challenging due to large fluctuations in flowrates, pollutants, and variable influent water compositions. A sequencing batch reactor (SBR) and modified SBR cycle-step-feed process (SSBR) configuration are studied in this work to effectively treat municipal wastewater while simultaneously removing nitrogen and phosphorus. To control the amount of dissolved oxygen in an SBR, three axiomatic control strategies (proportional integral (PI), fractional proportional integral (FPI), and fuzzy logic controllers) are presented. Relevant control algorithms have been designed using plant data with the models of SBR and SSBR based on ASM2d framework. On comparison, FPI showed a significant reduction in nutrient levels and added an improvement in effluent quality. The overall effluent quality is improved by 0.86% in FPI in comparison with PI controller. The SSBR, which was improved by precisely optimizing nutrient supply and aeration, establishes a delicate equilibrium. This refined method reduces oxygen requirements while reliably sustaining important biological functions. Focusing solely on the FPI controller's performance in terms of total air volume consumption, the step-feed SBR mechanism achieves an excellent 11.04% reduction in consumption.

High methane potential of oxygenic photogranules decreases after starvation.

Oxygenic photogranules (OPG) are granular biofilms that can treat wastewater without external aeration, making it an advantage over activated sludge. Excess of OPG biomass can serve as energy source through anaerobic digestion. Two sequencing batch photoreactors were operated over 400 days to grow OPG. Biochemical methane potentials (BMP) were obtained from near-infrared spectroscopy. OPGs had an average BMP of 356 mL CH4·gVS-1, much higher than typical BMP from activated sludge. A partial least squares analysis could relate BMP with reactor operating conditions, like light regime, load or biomass concentration. Since organic load was the most influential parameter on BMP, three starvation experiments were set up. An average decrease of BMP by 18.4 % was observed. However, the unexpected growth of biomass during starvation resulted in a higher total methane volume. In conclusion, starvation reduces the BMP of OPGs but anaerobic digestion of OPG biomass remains a promising route for biomass valorization.

Rheo-Optical Near-Infrared (NIR) Characterization of Styrene-Butadiene Rubber (SBR) Using Two-Trace Two-Dimensional (2T2D) Correlation Analysis.

A rheo-optical characterization technique based on the combination of near-infrared (NIR) spectroscopy and tensile testing was applied for the first time to an actual rubber sample based on styrene-butadiene rubber (SBR) including silica filler. When SBR samples were subjected to mechanical deformation, changes in the NIR spectral features were readily captured. Two-trace two-dimensional (2T2D) correlation analysis was then applied to the sets of NIR spectra to clearly reveal the subtle but pertinent difference between the NIR spectral features of the initial and deformed SBR. The initial deformation of the sample induces greater deformation of the soft butadiene groups than of the hard styrene groups. The inclusion of the silica filler and a coupling agent (CA) essentially develops firm links between the silica and butadiene via the CA to restrict the displacement of the butadiene during the tensile deformation of the system. The development of such linkage requires even more mechanical force to deform the SBR, which, in turn, improves Young's modulus of the rubber system. Asynchronous correlation spectra of SBR with no silica filler revealed that, during the deformation of the SBR, the butadiene groups were initially deformed, and this feature was then replaced by the predominant deformation of the hard styrene groups. On the other hand, this correlation feature became somewhat unclear when a similar analysis was applied to the SBR sample with silica filler, revealing subtle differences in interaction between individual comonomer functional groups distributed randomly along the copolymer chain and CA.

Rapid and specific detection of Pentastiridius leporinus by recombinase polymerase amplification assay.

Pentastiridius leporinus (Hemiptera: Cixiidae) is the main vector of an emerging and fast spreading sugar beet disease, the syndrome 'basses richesses' (SBR), in different European countries. The disease is caused by the γ-3-proteobacterium 'Candidatus Arsenophonus phytopathogenicus' and the phytoplasma 'Candidatus Phytoplasma solani' which are exclusively transmitted by planthoppers and can lead to a significant loss of sugar content and yield. Monitoring of this insect vector is important for disease management. However, the morphological identification is time consuming and challenging as two additional cixiid species Reptalus quinquecostatus and Hyalesthes obsoletus with a very close morphology have been reported in sugar beet fields. Further, identification of females and nymphs of P. leporinus at species level based on taxonomic key is not possible. In this study, an isothermal nucleic acid amplification based on recombinase polymerase amplification (RPA) was developed to specifically detect P. leporinus. In addition, real-time RPA was developed to detect both adults (male and female) and nymph stages using pure or crude nucleic acid extracts. The sensitivity of the real-time RPA for detection of P. leporinus was comparable to real-time PCR, but a shorter time (< 7 min) was required. This is a first report for real-time RPA application for P. leporinus detection using crude nucleic acid templates which can be applied for fast and specific detection of this vector in the field.

Efficacy and mechanism of enhanced Sb(V) removal from textile wastewater using ferric flocs in aerobic biological treatment.

Antimony contamination from textile industries has been a global environmental concern and the existing treatment technologies could not reduce Sb(V) to meet the discharge standards. To overcome this shortcoming, ferric flocs were introduced to expedite the biological process for enhanced Sb(V) removal in wastewater treatment plant (WWTP). For this purpose, a series of laboratorial-scale sequential batch reactor activated sludge processes (SBRs) were applied for Sb(V) removal with varied reactor conditions and the transformation of Fe and Sb in SBR system was investigated. Results showed a significant improvement in Sb(V) removal and the 20 mg L-1 d-1 iron ions dosage and iron loss rate was found to be only 15.2%. The influent Sb(V) concentration ranging 153-612 µg L-1 was reduced to below 50 µg L-1, and the maximum Sb(V) removal rate of the enhanced system reached about 94.3%. Furthermore, it exhibited high stability of Sb(V) removal in the face of antimonate load, Fe strike and matrix change of wastewater. Sludge total Sb determination and capacity calculation revealed decreasing in Sb adsorption capacity and desorption without fresh Fe dosage. While sludge morphology analysis demonstrated the aging and crystallization of iron hydroxides. These results verify the distinct effects of fresh iron addition and iron aging on Sb(V) removal. High-throughput gene pyrosequencing results showed that the iron addition changed microbial mechanisms and effect Fe oxidized bacterial quantity, indicating Sb(V) immobilization achieved by microbial synergistic iron oxidation. The present study successfully established a simple and efficient method for Sb(V) removal during biological treatment, and the modification of biological process by iron supplement could provide insights for real textile wastewater treatment.

Autohesion Mechanisms at Interfaces Between Random Copolymer Melts: Mesoscopic Simulations with Realistic Coarse-Grained Models.

The increase in welding time during the interdiffusion of a pair of non reacting random copolymer melts favors the strength rate of healing at the interface. Furthermore, the diffusion kinetic during the interpenetration of copolymer chains across the interface is strongly dependent on molecular weight. In this paper we perform mesoscopic simulations with realistic coarse grain models to study the autohesion mechanism across the interface between slightly entangled styrene-butadiene random copolymer melts.

Nitrite accumulation performance and microbial community of Algal-Bacterial symbiotic system constructed by Chlorella sp. And Navicula sp.

Chlorella sp. and Navicula sp. were separately used to construct an algal-bacterial symbiotic system in two identical sequencing batch reactors (R1 and R2) to explore the influence of algal species differences on nitrite accumulation. The Navicula-bacterial symbiotic system showed a higher nitrite accumulation efficiency of 85% and a stronger resistance to ammonia load. It secreted twice as many extracellular polymeric substances than the Chlorella-bacterial symbiotic system. Nitrospira and SM1A02 were the dominant functional genera of nitrite-oxidizing bacteria in R1. The dominant functional genus of ammonium-oxidizing bacteria and the dominant functional genus of denitrifying bacteria were Ellin6067 and unclassified_Saprospiraceae in R2, respectively. In general, this research provided some reference for the construction of an algal-bacterial symbiotic system and achieving nitrite accumulation through an algal-bacterial symbiotic system.

Enhancement of denitrification by sulfur-based carrier in sequencing batch reactor (SBR) for advanced wastewater treatment.

This study was to enhance the nitrogen removal efficiency in the sequencing batch reactor (SBR) process by adding sulfur-based carriers. The nitrogen removal efficiency of the control group was compared with that of the experimental group through a two-series operation of SBR1 without carrier and SBR2 with the carrier under the condition of no external carbon source. A total nitrogen (T-N) removal efficiency of 6.6%, 72.6%, and 79.9% was observed in SBR1, SBR2 (5%), and (10%), respectively. The T-N removal efficiency was improved in the system with carriers, which showed an increase in the removal efficiency of approximately 91.7%. The results suggest that the inclusion of the carrier led to an elevation in the sulfur ratio, implying an augmented surface area for sulfur-based denitrifying microorganisms. Additionally, CaCO3 contributed essential alkalinity for sulfur denitrification, thereby preventing a decline in pH. Regardless of the carrier, the efficiency of organic matter removal surpassed 89%, indicating that the sulfur-based carrier did not adversely affect the biological reaction associated with organic matter. Therefore, autotrophic denitrification was successfully performed using a sulfur carrier in the SBR process without an external carbon source, improving the nitrogen removal efficiency.

Evaluation of the Thermal Stability and Micro-Modification Mechanism of SBR/PP-Modified Asphalt.

To evaluate the thermal stability of composite polymer-modified asphalt, thermoplastic elastomer styrene-butadiene rubber (SBR)/polypropylene (PP) pellets were prepared using a hot-melt blending technique, with butyl rubber powder and waste polypropylene pellets as raw materials. The effects of different evaluation indexes on the thermal stability of SBR/PP-modified asphalt were investigated using a frequency scan test and a multi-stress creep recovery (MSCR) test, and the compatibility of SBR/PP particles with asphalt was studied using the Cole-Cole diagram and microstructure images. The tests show that, firstly, the performance grade (PG) classification of asphalt can be improved by adding an SBR/PP thermoplastic elastomer to enhance the adaptability of asphalt in high- and low-temperature environments, and the evaluation separation index can reflect the high-temperature storage stability of composite-modified asphalt more reasonably. Additionally, the larger the rubber-to-plastic ratio the worse the high-temperature thermal stability of composite-modified asphalt. Moreover, the addition of additives to the composite particles can promote the SBR/PP particles in the asphalt to be more uniformly dispersed, forming a more desirable microstructure and improving the thermal stability of composite-modified asphalt. Ultimately, the semicircular curve of the Cole-Cole diagram can reflect the compatibility characteristics of the two-phase structure of SBR/PP-modified asphalt, which can be used as an auxiliary index to evaluate the compatibility of polymer-modified asphalt.

Ascertaining appropriate measuring methods to determine tire wear particle pollution on driving school grounds in China.

Tire wear particles (TWPs) are garnering increasing attention due to their potential adverse environmental impacts. However, precisely ascertaining TWPs content is challenging due to the complexity and variability of the tire components used in the environment, indicating that more reliable methods to accurately determine TWPs are necessary. In this study, driving school grounds were used as a case study to ascertain an appropriate and reliable method to determine TWPs levels based on a comprehensive comparison between different analytical results using styrene butadiene rubber (SBR), N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine (6PPD), and zinc (Zn) as analytical markers. Thermogravimetric analysis-Gas chromatography mass spectrometry (TGA-GC-MS) method reliability using SBR was verified and applied to measure TWPs levels on driving school grounds. By reliably converting SBR content to TWPs content, the average TWPs content on driving school grounds was measured at 190.13 ± 101.89 mg/g. The highest TWPs content was 281.83 ± 171.44 mg/g under the reverse stall parking driving programs, while the slope start and stop driving programs was lower at 208.36 ± 124.11 mg/g. Our findings highlight the importance of accurately determining TWPs content within specific environments while comprehensively exploring associated patterns of change to better understand the environmental risks of TWPs.

Competitive enrichment of comammox Nitrospira in floccular sludge.

The discovery of complete ammonium oxidation (comammox) has subverted the traditional perception of two-step nitrification, which plays a key role in achieving biological nitrogen removal from wastewater. Floccular sludge-based treatment technologies are being applied at the majority of wastewater treatment plants in service where detection of various abundances and activities of comammox bacteria have been reported. However, limited efforts have been made to enrich and subsequently characterize comammox bacteria in floccular sludge. To this end, a lab-scale sequencing batch reactor (SBR) in the step-feeding mode was applied in this work to enrich comammox bacteria through controlling appropriate operational conditions (dissolved oxygen of 0.5 ± 0.1 g-O2/m3, influent ammonium of 40 g-N/m3 and uncontrolled longer sludge retention time). After 215-d operation, comammox bacteria gradually gained competitive advantages over counterparts in the SBR with a stable nitrification efficiency of 92.2 ± 2.2 %: the relative abundance of Nitrospira reached 42.9 ± 1.3 %, which was 13 times higher than that of Nitrosomonas, and the amoA gene level of comammox bacteria increased to 7.7 ± 2.1 × 106 copies/g-biomass, nearly 50 times higher than that of conventional ammonium-oxidizing bacteria. The enrichment of comammox bacteria, especially Clade A Candidatus Nitrospira nitrosa, in the floccular sludge led to (i) apparent affinity constants for ammonium and oxygen of 3.296 ± 0.989 g-N/m3 and 0.110 ± 0.004 g-O2/m3, respectively, and (ii) significantly low N2O and NO production, with emission factors being 0.136 ± 0.026 % and 0.023 ± 0.013 %, respectively.

Comparison of benzotriazole ultraviolet stabilizers (BUVs) removal from wastewater after subsequent stages of sequencing batch reactor (SBR) treatment process.

The research focused on benzotriazole ultraviolet stabilizers (BUVs) which are commonly used compounds despite being found dangerous, e.g. promoting breast cancer cell proliferation, damaging vital organs such as hearts, brains livers and kidneys. The aim of the study was to analyse the efficiency and removal rate of BUVs from wastewater depending on the quantity of tested compounds and SBR anaerobic-aerobic conditions. The study was conducted in sequencing batch reactors (SBRs - 17 L) with real flocculent activated sludge (8 L) and model wastewater (5 L) containing UV-326, UV-327, UV-328, UV-329 and UV-P from 50 to 600 µg∙L-1. The SBR were operated in 390 cycles of 7 h and 10 min over 130 days. The similarity of the technological parameters of the treatment process to those used in a real wastewater treatment plant was maintained. Efficiency removal of individual BUVs was strictly dependent on the dose of compounds introduced into wastewater and ranged from 68.2 to 97 %. Removal of UV-329 occurred with lowest efficiency (from 68.2 to 85.2 %) while UV-326 was most efficiently removed from the wastewater (from 94.1 to 97 %). UV-329 was removed from wastewater with the lowest (0.0968-0.9524 µg∙L-1∙min-1) average removal rate while UV-327 with the highest (0.16-1.3357 µg∙L-1∙min-1), irrespective of BUVs dose in the influent. Secondary release of BUVs into the wastewater occurred in SBR during the settling phase and was dependent on the type and concentration of the BUVs in the raw wastewater. This occurrence was noted for UV-326 ≥ 100; UV-327 = 600; UV-328 ≥ 200; UV-329 ≥ 50 and UV-P ≥ 100 µg∙L-1. The settling phase needs to be shortened to the required minimum. This is an important conclusion for WWTPs in regards to SBR cycle duration and technological parameters of the treatment process.

Raw and Pre-Treated Styrene Butadiene Rubber (SBR) Dust as a Partial Replacement for Natural Sand in Mortars.

The circular economy (CE) is widely known for its emphasis on reducing waste and maximizing the use of resources by reusing, recycling, and repurposing materials to create a sustainable and efficient system. The CE is based on 3R-reuse, reduce, and recycle. The aim of this article is to use styrene butadiene rubber dust (SBR) in building material, constituting secondary waste in the production of SBR, which is currently disposed of as landfill. SBR is partly intended to replace the natural raw material sand. The purpose of the final material is to use it for its light weight, insulating properties, or ability to absorb vibrations and sounds. Various shares of SBR dust in mortars were tested. Some of the mortars used SBR thermal pre-treatment at temperatures of 200, 275, and 350 °C. The strength and SEM results are presented. The best pre-treatment for SBR dust is thermal treatment at 275 °C. The maximum usage of rubber dust with thermal treatment is 60% as a sand substitute. The novel finding of this study is the possibility to use more than 30% rubber dust (as a substitute for sand) thanks to pre-treatment, whereby 30% is a common maximum ratio in mortars.

Effect of Fillers Modification with ILs on Fillers Textural Properties: Thermal Properties of SBR Composites.

In this work, we present the effect of graphene nanoplatelets (GnPs) modification with ionic liquids (ILs). The textural properties of graphene nanoplatelets (GnPs) used as styrene-butadiene rubber's filler and the thermal properties of the composites obtained with the use of the mentioned fillers were investigated. GnPs were modified with 1-butylpyridinium bromide (BPyBr) and 4-methyl-1-butylpyridinium bromide (BmPyBr) through two different ways. One strategy has been to deposit the filler modifier from the solution. The second one involved the modification of the filler with ionic liquids in bulk during the preparation of elastomer blends. Settlement of the proposed ionic liquids onto the GnPs' surface led to significant changes in the textural characteristics. BPyBr has restricted the filler's microporosity, whereas BmPyBr has caused the formation of a more opened filler structure without the increase in its average pore size. GnPs modified with ILs led to reducing the temperature of vulcanization of SBR compounds and affected the thermal stability of the composites.

A Highly Bright Near-Infrared Afterglow Luminophore for Activatable Ultrasensitive In Vivo Imaging.

Afterglow luminescence imaging probes, with long-lived emission after cessation of light excitation, have drawn increasing attention in biomedical imaging field owing to their elimination of autofluorescence. However, current afterglow agents always suffer from an unsatisfactory signal intensity and complex systems consisting of multiple ingredients. To address these issues, this study reports a near-infrared (NIR) afterglow luminophore (TPP-DO) by chemical conjugation of an afterglow substrate and a photosensitizer acting as both an afterglow initiator and an energy relay unit into a single molecule, resulting in an intramolecular energy transfer process to improve the afterglow brightness. The constructed TPP-DO NPs emit a strong NIR afterglow luminescence with a signal intensity of up to 108  p/s/cm2 /sr at a low concentration of 10 µM and a low irradiation power density of 0.05 W/cm2 , which is almost two orders of magnitude higher than most existing organic afterglow probes. The highly bright NIR afterglow luminescence with minimized background from TPP-DO NPs allows a deep tissue penetration depth ability. Moreover, we develop a GSH-activatable afterglow probe (Q-TPP-DO NPs) for ultrasensitive detection of subcutaneous tumor with the smallest tumor volume of 0.048 mm3 , demonstrating the high potential for early diagnosis and imaging-guided surgical resection of tumors.

Effect of Sasobit/Waste Cooking Oil Composite on the Physical, Rheological, and Aging Properties of Styrene-Butadiene Rubber (SBR)-Modified Bitumen Binders.

The modifying effects of polymer on bitumen low-temperature performance are substantially compromised by the thermal breakdown of styrene-butadiene rubber (SBR) polymer during bitumen mixture production operations. The efficacy of the utilization of Sasobit/waste cooking oil (Sasobit/WCO) as a warm-mix additive has been demonstrated in mitigating the adverse consequences of thermal aging on SBR-modified bitumen binder (SB) while preserving the binder's original performance characteristics. However, few studies have been conducted to further investigate the rheological properties and aging resistance of SB modified with Sasobit/WCO compounds. In this work, three additives-Sasobit, WCO, and Sasobit/WCO composite-were selected, and their effects on the physical and rheological characteristics of SB as well as the temperatures at which the mixtures were prepared were assessed. In addition, by using dynamic shear rheometers (DSR) and bending beam rheometers (BBR), the effects of this innovative warm-mix addition on the performance grade (PG) and aging resistances of SB were evaluated. According to the results, Sasobit/WCO composites outperform Sasobit and WCO in lowering the mixture preparation temperature. Sasobit/WCO also improves both the high- and low-temperature performance of SB simultaneously. Compared to hot-mix asphalt mixtures, the addition of Sasobit/WCO reduces the preparation temperature of the bitumen mixtures by 19 °C, which in turn helps to minimize the negative effects of temperature aging on the functioning of the SB. Additionally, the Sasobit/WCO composite addition can improve the SB mixture's resistance to thermal cracking. After the introduction of Sasobit/WCO, the high-temperature PG of SB was raised by two levels, regardless of whether the warm-mix impact was taken into account. With the addition of Sasobit/WCO, SB's resilience to short-term aging was enhanced.

The Importance of the Mineral Substrate of the Biofilm in the Process of Low-Temperature Removal of Nitrogen Compounds from Wastewater.

This study researched the use of biofilms to remove nitrogen compounds from municipal sewages at low temperatures, especially in winter. An aluminosilicate substrate was used to create a biofilm, which has an affinity for ammonium ions. The selection of biofilm-forming microorganisms has been shown to occur on aluminosilicate. This substrate is mainly inhabited by microorganisms that remove nitrogen compounds. As a result, microorganisms protected against external factors in the biofilm effectively remove nitrogen compounds. The TN content in sewage treated at a temperature of 10 °C was of a 4 mg/L order and was 3-5 times lower than in the reference system (classical conditions). This process involves shortened nitrification/denitrification such as Anammox. As a result of a given process, CO2 emissions were reduced and much smaller amounts of NOx were produced, positively impacting the ongoing climate changes. Microbiological DNA/RNA tests have shown that the biofilm is primarily composed of archaea and bacteria that remove nitrogen compounds, including those that oxidize ammonia.

Optimization of activated sludge polyhydroxyalkanoates(PHAs) synthesis system by performing sludge activity recovery experiments and varying the initial sludge concentration.

Polyhydroxyalkanoates(PHAs) are considered a good alternative to petroleum-based plastics because of their good biodegradability and biocompatibility. The synthesis of PHAs using activated sludge can not only solve the problem of the high cost of pure cultures but also improve the utilization value of activated sludge. In this study, sludge activity recovery experiments were firstly conducted and the effects of different initial sludge concentrations on the activated sludge PHAs synthesis system were further investigated. the initial sludge concentrations were 1#SBR (2800 ± 50) mg/L, 2#SBR (4200 ± 50) mg/L, and 3#SBR (5500 ± 50) mg/L. The results showed that the activity, sedimentation performance and PHAs synthesis capacity of activated sludge were enhanced after the sludge activity recovery experiment. At the initial sludge concentration of 4200 mg/L, the activated sludge PHAs synthesis system was operated stably and the synthesis efficiency of PHAs was enhanced. In contrast, at the initial sludge concentration of 2800 and 5500 mg/L, the steady state of the activated sludge PHAs synthesis system was damaged to different degrees at different times, and the synthesis efficiency of PHAs was greatly reduced.

A novel sulfur autotrophic denitrification in-situ coupled sequencing batch reactor system to treat low carbon to nitrogen ratio municipal wastewater: Performance, niche equilibrium and pollutant removal mechanisms.

A novel integrated sulfur fixed-film activated sludge in SBR system (IS0FAS-SBR) was proposed to treat the low C/N ratio municipal wastewater. The effluent total inorganic nitrogen (TIN) and PO43--P decreased from 17 mg/L and 3.5 mg/L to 8.5 mg/L and 0.5 mg/L, and higher nitrogen removal efficiency was contributed by the autotrophic denitrification. Microbial response characteristics showed that catalase (CAT), reduced nicotinamide adenine dinucleotide (NADH) and extracellular polymeric substance (EPS) alleviated the oxidative stress of sulfur carrier to maintain cell activity, while metabolic activity analysis indicated that the electron transfer rate was enhanced to improve mixotrophic denitrification efficiency. Meanwhile, the increased key enzyme activities further facilitated nitrogen removal and sulfur oxidation process. Additionally, the microbial community, functional proteins and genes revealed a niche equilibrium of C, N, S metabolic bacteria. Sulfur autotrophic in-situ coupled SBR system enlarged a promising strategy for treatment of low C/N ratio municipal wastewater.