Biomecánica de la interfaz hueso-tornillo en instrumentación transpedicular de columna / Biomechanics of the bone-screw interface in transpedicular spinal instrumentation

Resumen: El aflojamiento de los implantes, la falla catastrófica de la interfaz hueso-tornillo, la migración de material y la pérdida de estabilidad de los componentes del ensamble de la fijación constituyen una seria complicación en la cirugía de columna de adultos. La contribución de la biomecánica se basa en la medición experimental y la simulación de las fijaciones transpediculares de columna. La trayectoria de inserción cortical mostró un incremento en la resistencia de la interfase tornillo-hueso respecto a la inserción pedicular tanto para fuerzas de tracción axiales al tornillo como en distribución de esfuerzos en la vértebra. Los tornillos de doble rosca tuvieron una resistencia similar a los pediculares estándar. Los tornillos de rosca parcial de cuatro filetes mostraron mejor resistencia a la fatiga en cuanto a mayor carga de rotura y número de ciclos para la falla. Los tornillos aumentados, ya sea con cemento o hidroxiapatita mejoraron también la resistencia a la fatiga en vértebras osteoporóticas. Las simulaciones de segmentos rígidos confirmaron la presencia de esfuerzos superiores en los discos intervertebrales que provocan el daño de los segmentos adyacentes. La parte posterior de las vértebras puede estar sometida a mayores esfuerzos, fundamentalmente en la superficie de la interfaz hueso-tornillo, por lo que son más susceptibles a la falla en esta región.

Abstract: Implant loosening, catastrophic failure of the bone-screw interface, material migration, and loss of stability of the fixation component assembly constitute a serious complication in adult spinal surgery. The contribution of biomechanics is based on experimental measurement and simulation of transpedicular spinal fixations. The cortical insertion trajectory showed an increase in the resistance of the screw-bone interface with respect to the pedicle insertion trajectory, both for axial traction forces to the screw and for stress distribution in the vertebra. The double-threaded screws and standard pedicle screws had similar strength. Partially threaded screws with four-thread showed better resistance to fatigue in terms of a higher failure load and number of cycles to fail. Cement or hydroxyapatite augmented screws with also showed a better fatigue resistance in osteoporotic vertebrae. Rigid segment simulations confirmed the presence of higher stresses on the intervertebral discs causing damage to adjacent segments. The posterior body of the vertebra may be subjected to high stresses, in the bone-screw interface, being this bone region more susceptible to failure.

[Biomechanics of the bone-screw interface in transpedicular spinal instrumentation]. / Biomecánica de la interfaz hueso-tornillo en instrumentación transpedicular de columna.

Implant loosening, catastrophic failure of the bone-screw interface, material migration, and loss of stability of the fixation component assembly constitute a serious complication in adult spinal surgery. The contribution of biomechanics is based on experimental measurement and simulation of transpedicular spinal fixations. The cortical insertion trajectory showed an increase in the resistance of the screw-bone interface with respect to the pedicle insertion trajectory, both for axial traction forces to the screw and for stress distribution in the vertebra. The double-threaded screws and standard pedicle screws had similar strength. Partially threaded screws with four-thread showed better resistance to fatigue in terms of a higher failure load and number of cycles to fail. Cement or hydroxyapatite augmented screws with also showed a better fatigue resistance in osteoporotic vertebrae. Rigid segment simulations confirmed the presence of higher stresses on the intervertebral discs causing damage to adjacent segments. The posterior body of the vertebra may be subjected to high stresses, in the bone-screw interface, being this bone region more susceptible to failure.

El aflojamiento de los implantes, la falla catastrófica de la interfaz hueso-tornillo, la migración de material y la pérdida de estabilidad de los componentes del ensamble de la fijación constituyen una seria complicación en la cirugía de columna de adultos. La contribución de la biomecánica se basa en la medición experimental y la simulación de las fijaciones transpediculares de columna. La trayectoria de inserción cortical mostró un incremento en la resistencia de la interfase tornillo-hueso respecto a la inserción pedicular tanto para fuerzas de tracción axiales al tornillo como en distribución de esfuerzos en la vértebra. Los tornillos de doble rosca tuvieron una resistencia similar a los pediculares estándar. Los tornillos de rosca parcial de cuatro filetes mostraron mejor resistencia a la fatiga en cuanto a mayor carga de rotura y número de ciclos para la falla. Los tornillos aumentados, ya sea con cemento o hidroxiapatita mejoraron también la resistencia a la fatiga en vértebras osteoporóticas. Las simulaciones de segmentos rígidos confirmaron la presencia de esfuerzos superiores en los discos intervertebrales que provocan el daño de los segmentos adyacentes. La parte posterior de las vértebras puede estar sometida a mayores esfuerzos, fundamentalmente en la superficie de la interfaz hueso-tornillo, por lo que son más susceptibles a la falla en esta región.

Orthodontic mini-implants: clinical and peri-implant evaluation.

The study evaluated the clinical changes of orthodontic mini-implants (MI) inserted for the purpose of anchoring during orthodontic treatment. The null hypotheses were: 1-that there is no correlation between proximity of the MI to the root and peri-implantitis or mobility; 2-that peri-implantitis does not interfere with mobility; 3-that the pain is not related to mobility or peri-implantitis. Forty (40) patients were selected and the MI were evaluated for each patient. MI in the upper and lower arch were evaluated for a period of approximately 6 months with relationship to the distance MI - root, peri-implantitis, mobility, biological damage and pain through the analysis of periapical radiography and clinical/periodontal evaluation. The evaluations were performed out by means of scores and a correlation was made between the variables. No statistically significant differences were found between the upper and lower arch in the variables evaluated, except for the mobility that was more present in the lower arch (p = 0.0336). There was a correlation between peri-implantitis and mobility (p = 0.0003) and between pain and mobility (p = 0.0443). However, there was no correlation between a greater degree of peri-implantitis and greater mobility (p = 0.7054). In addition, the MI placed too close to the root showed peri-implantitis (p = 0.0142). The null hypotheses were rejected because there was a positive correlation between the analyzes. The placement of MI close to the root led to greater peri-implantitis. Patients who reported pain had greater mobility of the MI and peri-implantitis led to greater mobility.

Tomographic assessment of infrazygomatic crest bone depth for extra-alveolar miniscrew insertion in subjects with different vertical and sagittal skeletal patterns.

OBJECTIVE: To evaluate bone availability at the infrazygomatic crest for extra-alveolar bone miniscrew insertion in subjects with different vertical and sagittal skeletal patterns. SETTING AND SAMPLE POPULATION: Measurements of the infrazygomatic crest were performed on multislice computed tomography scans from 58 adults with different skeletal patterns. MATERIALS AND METHODS: Infrazygomatic crest bone depth was measured at 4, 5 and 6 mm from the cementoenamel junction (CEJ) of the maxillary first molar at three different angles (60°, 70° and 80°) in the first molar occlusal plane. The sagittal and vertical skeletal patterns were determined. Analysis of variance followed by Tukey's post hoc test was used (P ≤ .05). RESULTS: Bone depth was greater near the CEJ (8.7 ± 3.1 mm) and lower in the apical area (5.8 ± 2.7 mm). In Class II subjects, considering 6 mm from the CEJ, there was a significantly lower depth at the 80° angle (5.4 ± 2.5 mm) than at 60° (8.6 ± 3.5 mm; P = .007). In mesofacial subjects, considering 5 and 6 mm from the CEJ, bone depth was lower at 80° (5.7 ± 3.2 mm and 5.3 ± 2.5 mm) than at 60° considering 4 mm from the CEJ (P ≤ .019). CONCLUSION: Bone availability was lower at the apical level, especially in Class II and mesofacial subjects. Therefore, when the planned insertion site is located in the apical direction, it is recommended to choose shorter miniscrews (2.0 x 12mm) and a smaller insertion angle (60°) and/or to plan a miniscrew bone insertion deep enough to allow bicortical fixation.

Long-term follow-up of ais treated surgically with pedicular screws / Seguimiento a largo plazo de eia intervenida quirúrgicamente con tornillos pediculares / Acompanhamento a longo prazo de eia tratada cirurgicamente com parafusos peduculares

ABSTRACT Objective: In the last three decades, there have been great advances in the surgical treatment of adolescent idiopathic scoliosis. There are few studies that focus on the long-term clinical and radiographic results of AIS operated on with pedicle screws that also consider psychological repercussions. Methods: We conducted an observational longitudinal study. We reviewed the AIS cases that were operated on with pedicle screws in our center between January 2009 and December 2010. We conducted follow-up until July 2019. A short questionnaire was administered to assess patient satisfaction and the long-term impact from both psychological and functional points of view. Results: A total of 19 patients met the inclusion criteria. The mean preoperative Cobb was 58°, the postoperative was 23° and at the end of follow-up it was 26°. No major complications were reported. Ninety percent were very satisfied with the overall results of the surgery. Ninety-five percent had no limitation for sports or daily activities and 90% were satisfied with the cosmetic results. Conclusion: The short- and long-term radiographic evolution in patients treated with third generation material presented good clinical results. In 3 cases (16%) loss of correction greater than 10% was reported. The overall satisfaction index and cosmetic results were very good at the end of follow-up despite the low correction rate (60%). There were no major complications and the incidence of functional limitation and pain at the end of the follow-up was very low. Level of evidence IV; Review article.

RESUMO Objetivo: Nas últimas três décadas houve grandes avanços no tratamento cirúrgico da escoliose idiopática do adolescente. Existem poucos trabalhos que estudam os resultados clínicos e radiográficos a longo prazo de EIA, tratados cirurgicamente com parafusos pediculares que também considerem a repercussão psicológica. Métodos: Realizamos um estudo longitudinal observacional. Analisamos a EIA de pacientes operados entre janeiro de 2009 e dezembro de 2010 que receberam parafusos pediculares em nosso centro. Realizamos o acompanhamento até julho de 2019. Foi realizado um breve questionário para avaliar a satisfação dos pacientes e a repercussão a longo prazo do ponto de vista psicológico e funcional. Resultados: Um total de 19 pacientes satisfizeram os critérios de inclusão. A média de Cobb pré-operatório foi de 58° e o pós-operatório foi de 23° e ao final do acompanhamento, de 26°. Não foram registradas complicações relevantes. Quanto à satisfação, 90% estão muito satisfeitos com o resultado geral da cirurgia, 95% não têm limitações para esportes ou atividades diárias e 90% estão satisfeitos com os resultados estéticos. Conclusões: A evolução radiográfica a curto e longo prazo nos pacientes tratados com material de terceira geração apresentou bons resultados clínicos. Em 3 casos (16%), registrou-se perda de correção superior a 10%. O índice geral de satisfação e resultado estético é muito bom no final do acompanhamento, apesar da baixa taxa de correção (60%). Não se constataram complicações importantes e a incidência de limitação funcional e dor ao final do acompanhamento foi muito baixa. Nível de evidência IV; Artigo de revisão.

RESUMEN Objetivo: En las últimas tres décadas han habido grandes avances en el tratamiento quirúrgico de las escoliosis idiopática del adolescente. Existen pocos trabajos que estudien el resultado clínico y radiográfico a largo plazo en las EIA intervenidas con tornillos pediculares que además contemplen repercusión psicológica. Métodos: Realizamos un estudio longitudinal observacional. Revisamos las EIA intervenidas entre enero de 2009 y diciembre de 2010 con tornillos pediculares en nuestro centro. Realizamos seguimiento hasta julio de 2019. Se realizó un breve cuestionario para evaluar satisfacción de los pacientes y la repercusión a largo plazo de punto de vista psicológico y funcional. Resultados: Un total de 19 pacientes cumplieron los criterios de inclusión. La media del Cobb pre operatorio fue de 58° y el post operatorio de 23° y al final del seguimiento, de 26°. No se registraron complicaciones mayores. El 90% está muy satisfecho con el resultado global de la cirugía. El 95% no presenta limitación para el deporte o actividad cotidiana y el 90% está conforme con resultado cosmético. Conclusiones: La evolución radiográfica a corto y largo plazo en pacientes tratados con material de tercera generación presentó buenos resultados clínicos. En 3 casos (16%) se registró perdida de corrección mayor a 10%. El índice de satisfacción global y resultado cosmético es muy bueno al final del seguimiento a pesar de la baja tasa de corrección (60%). No se constataron complicaciones mayores y la incidencia de limitación funcional y dolor al final del seguimiento fue muy baja. Nivel de evidencia IV; Estudio de revisión.

Diagnostic accuracy of perioperative electromyography in the positioning of pedicle screws in adolescent idiopathic scoliosis treatment: a cross-sectional diagnostic study.

BACKGROUND: To investigate in the conventional techniques of the pedicle screws using triggered screw electromyography (t-EMG), considering different threshold cutoffs: 10, 15, 20 25 mA, for predicting pedicle screw positioning during surgery of the adolescent with idiopathic scoliosis (AIS). METHODS: Sixteen patients (4 males, 12 females, average age 16.6 years) were included, with an average curve magnitude of 50 degrees and placement of 226 pedicle screws. Each screw was classified as "at risk for nerve injury" (ARNI) or "no risk for nerve injury" (NRNI) using CT and the diagnostic accuracy of EMG considering different threshold cutoffs (10,15, 20 and 25 mA) in the axial and Sagittal planes for predicting screw positions ARNI was investigated. RESULTS: The EMG exam accuracy, in the axial plane, 90.3% screws were considered NRNI. In the sagittal plane, 81% pedicle screws were considered NRNI. A 1-mA decrease in the EMG threshold was associated with a 12% increase in the odds of the screw position ARNI. In the axial and sagittal planes, the ORs were 1.09 and 1.12, respectively. At every threshold cutoff evaluated, the PPV of EMG for predicting screws ARNI was very low in the different threshold cutoff (10 and 15); the highest PPV was 18% with a threshold cutoff of 25 mA. The PPV was always slightly higher for predicting screws ARNI in the sagittal plane than in the axial plane. In contrast, there was a moderate to high NPV (78-93%) for every cutoff analyzed. CONCLUSIONS: EMG had a moderate to high accuracy for positive predicting value screws ARNI with increase threshold cutoffs of 20 and 25 mA. In addition, showed to be effective for minimizing false-negative screws ARNI in the different threshold cutoffs of the EMG in adolescent with idiopathic scoliosis (AIS).

Distalization of the entire maxillary arch with mini-implants in the posterior palatal alveolus- A case report / Distalização de todo o arco maxilar com mini-implantes na região alveolar posterior palatina - Relato de caso

A 22 year old male patient reported to the hospital with a chief complaint of forwardly placed teeth. On examination patient had Angle's Class I malocclusion and proclination of the anterior teeth. There were signs of frictional keratosis on the buccal mucosa. Treatment plan was to extract the third molars alone and distalize the entire maxillary arch with palatal mini-implants. 0.022 MBT brackets were bonded on the buccal aspect. 0.019" x 0.025" stainless steel wire was placed sequentially. Mini-implants were placed on the posterior alveolus on the palatal surface of maxilla. Retractive force was applied from an attachment bonded on the palatal aspect of the maxillary canine. Patient was reviewed periodically. Comparison of pre-treatment and post-treatment results revealed that the entire maxillary arch intruded and translated distally with a counter-clockwise rotation of the mandible with reduction in LAFH. There was a mild reduction in inter-canine with marginal expansion in the premolar and molar region. An improvement in facial profile was noted with no sign of root resorption. Thus, the posterior alveolus may be considered as a new and appropriate site for placement of mini-implant to bring about distal movement of the entire maxillary dentition (AU)

Um Paciente do sexo masculino, 22 anos, foi encaminhado ao hospital com queixa principal de dentes posicionados para a frente. Ao exame clínico o paciente apresentava má oclusão de Classe I de Angle e inclinação vestibular dos dentes anteriores. Havia sinais de queratose friccional na mucosa bucal. O plano de tratamento foi extrair os terceiros molares e distalizar todo o arco maxilar com mini-implantes por palatino. Bráquetes MBT 0,022 foram colados por vestibular. Fio de aço inoxidável 0,019 "x 0,025" foi colocado seqüencialmente. Mini-implantes foram instalados na região alveolar posterior da superfície palatina da maxila. A força de retração foi aplicada a partir de acessórios colados nas faces palatinas dos caninos superiores. O paciente foi reavaliado periodicamente. Os resultados da comparação pré-tratamento e pós-tratamento revelaram que todo o arco maxilar intruiu e transladou distalmente com rotação da mandíbula no sentido anti-horário com redução da AFAI. Houve uma ligeira redução na distância intercanina com expansão marginal nas regiões de pré-molar e molar. Foi percebida melhora no perfil facial sem sinal de reabsorção radicular. Assim, a região alveolar posterior pode ser considerada como um novo e apropriado local para instalação de mini-implante para promover movimento distal de toda a dentição maxilar. (AU)

Evaluation of miniscrew angulation in the posterior maxilla using cone-beam computed tomographic image

ABSTRACT Objective: This study aimed at evaluating whether changes in the insertion angle is a determining factor in the positioning of the miniscrews body in a region with larger interradicular space in the posterior maxilla. Methods: Analysis of 60 posterior maxillary quadrants were made using images obtained by means of cone-beam computed tomographic image (CBCT), with 0.076-mm voxel, which presented a real miniscrew inserted in the mesial region of the maxillary first molars, serving as reference point for the placement of the virtual miniscrews. Measurements of the distances between roots were made in three points on the body of the virtual miniscrews (A, B and C), at four different angulations, 70o, 60o, 50o and 40o (T1 to T4), in relation to the long axis of the second premolar. This evaluation was made in four groups, selected in accordance with the disposition of the roots of the second premolars and first molars: Group 1 (all types of roots), Group 2 (convergent roots), Group 3 (divergent roots) and Group 4 (parallel roots). Results: There were no statistically significant differences in the measurements of points A, B and C, at the different angles (70o, 60o, 50o and 40o) and in the different groups (p > 0.05). Conclusions: Changes in the insertion angle is not a determinant factor in the positioning of miniscrews body in regions with larger interradicular space in posterior maxilla.

RESUMO Objetivo: o presente estudo objetivou avaliar se alterações no ângulo de inserção do miniparafuso são um fator decisivo para a adaptação do corpo do parafuso em áreas com espaço inter-radicular aumentado, na região posterior da maxila. Métodos: foram realizadas análises em 60 quadrantes maxilares posteriores, a partir de imagens obtidas por tomografia computadorizada de feixe cônico (TCFC), com voxel de 0,076 mm, as quais apresentavam um miniparafuso real inserido na região mesial dos primeiros molares superiores, utilizado como ponto de referência para a inserção de miniparafusos virtuais. As distâncias inter-radiculares foram mensuradas utilizando-se três pontos marcados no corpo dos miniparafusos virtuais (A, B e C), inseridos com quatro angulações diferentes (70°, 60°, 50° e 40°) (T1 a T4) em relação ao longo eixo do segundo pré-molar. A avaliação foi realizada em quatro grupos, selecionados de acordo com a disposição das raízes dos segundos pré-molares e primeiros molares: Grupo 1 - contendo todos os tipos de raízes; Grupo 2 - raízes convergentes; Grupo 3 - raízes divergentes; e Grupo 4 - raízes paralelas. Resultados: não houve diferença estatisticamente significativa entre as medidas dos pontos A, B e C nas diferentes angulações (70°, 60°, 50° e 40°) ou entre os grupos (p > 0,05). Conclusões: alterações no ângulo de inserção dos miniparafusos não são um fator decisivo para a adaptação do corpo do parafuso, em áreas com espaço inter-radicular aumentado entre primeiro molar e segundo pré-molar superiores.

Positioning of pedicle screws in adolescent idiopathic scoliosis using electromyography / Posição de parafusos pediculares na escoliose idiopática do adolescente com uso da eletromiografia / Posición de tornillos pediculares en escoliosis idiopática del adolescente con electromiografía

To analyze the occurrence of poor positioning of pedicle screws inserted with the aid of intraoperative electromyographic stimulation in the treatment of Adolescent Idiopathic Scoliosis (AIS).

Analisar a ocorrência do mau posicionamento de parafusos pediculares inseridos com auxílio de estimulação eletromiográfica intraoperatória, no tratamento de escoliose idiopática do adolescente (EIA).

Analizar la incidencia de la mala colocación de tornillos pediculares insertados con la ayuda de la estimulación electromiográfica intraoperatoria para el tratamiento de la Escoliosis Idiopática del Adolescente (EIA).

Outcome comparison of Lisfranc injuries treated through dorsal plate fixation versus screw fixation.

OBJECTIVE: The objective of this prospective study was to test whether the treatment of Lisfranc injuries with open reduction and dorsal plate fixation would have the same or better functional outcomes as treatment with standard trans-articular screw fixation. METHODS: Sixty patients with primarily isolated Lisfranc joint injury were treated by open reduction and dorsal plate fixation or standard screw fixation. The patients were followed on average for 31 months. Evaluation was performed with patients' chief complaint, clinical examination, radiography, and AOFAS Midfoot Scale. RESULTS: Thirty two patients were treated with open reduction and dorsal plate fixation, and twenty eight patients were treated with open reduction and screw fixation. After two years follow-up, the mean AOFAS Midfoot score was 83.1 points in the dorsal plate fixation group and 78.5 points in the screw fixation group (p<0.01). Of the dorsal plate fixation group, radiographic analysis revealed anatomic reduction in twenty-nine patients (90.6%, 29/32) and nonanatomic reduction in three patients. Of the screw fixation group, radiographic analysis revealed anatomic reduction in twenty-three patients and nonanatomic reduction in five patients (82.1%, 23/28). CONCLUSIONS: Open reduction and dorsal plate fixation for a dislocated Lisfranc injury do have better short and median term outcome and a lower reoperation rate than standard screw ORIF. In our experience, we recommend using dorsal plate in ORIF on dislocated Lisfranc injuries. Level of Evidence II, Prospective Comparative Study.

Pre-tibial synovial cyst after reconstruction of the anterior cruciate ligament: case report / Cisto sinovial pré-tibial após reconstrução do LCA – Relato de caso

Arthroscopic reconstruction of the anterior cruciate ligament has been modernized through new surgical techniques and new materials. When tibial fixation is performed using an absorbable screw, complications may occur, such as formation of a pre-tibial cyst. The case described here is about a patient who presented an anteromedial synovial cyst in his right knee, three years after having undergone ACL reconstruction. The patient did not present any pain nor any complaints other than a mass that progressively increased in size, worsened after physical activities. Imaging examinations were requested: simple radiography of the knee and magnetic resonance. Anteromedial imaging of the knee showed a mass with well-delimited borders and internal fluid content, suggestive of a synovial cyst, with communication with the joint cavity through the tibial tunnel, without presenting enlargement or absorption of the bone tunnel. The cyst was surgically resected and the tibial tunnel occlusion was performed using a bone plug. The diagnosis of a synovial cyst was subsequently confirmed through the results from the anatomopathological examination. The patient presented good clinical evolution, with disappearance of the symptoms and a return to physical activities...

A reconstrução do ligamento cruzado anterior (LCA) por via artroscópica vem sendo modernizada por novas técnicas cirúrgicas e novos materiais. Quando feita a fixação tibial com parafuso absorvível podem ocorrer complicações, como a formação de um cisto pré-tibial. O caso em questão é de um paciente que apresentou um cisto sinovial anteromedial em joelho direito três anos após ter sido submetido a reconstrução do LCA. O paciente não apresentava dor ou outras queixas, apenas massa de aumento progressivo, com pioria após atividades físicas. Foram solicitados exames de imagem: radiografias simples do joelho que não apresentavam alterações; e ressonância magnética com imagem anteromedial em joelho sugestiva de cisto sinovial. Apresentava bordas bem delimitadas e conteúdo líquido interno, com comunicação com a cavidade articular através do túnel tibial, sem apresentar alargamento ou absorção do túnel ósseo. Foram feitas ressecção cirúrgica do cisto e oclusão do túnel tibial com tampão ósseo, com posterior confirmação do diagnóstico de cisto sinovial após resultado do exame anatomopatológico. O paciente apresentou boa evolução clínica, com desaparecimento dos sintomas e retorno às atividades físicas...

Outcome comparison of lisfranc injuries treated through dorsal plate fixation versus screw fixation

O objetivo deste estudo prospectivo foi testar se o tratamentode lesões de Lisfranc com redução aberta e fixação da placadorsal teria os mesmos resultados funcionais, ou melhores, do quetratamento padrão com fixação com parafuso transarticular. Métodos:Sessenta pacientes com lesão articular de Lisfranc foram tratadospor redução aberta e fixação da placa dorsal ou pelo método padrãopor fixação de parafusos. Os pacientes foram acompanhados por,em média, 31 meses. A avaliação foi realizada com base na queixaprincipal dos pacientes, exame clínico, radiografia, e escala AOFAS.Resultados: Trinta e dois pacientes foram tratados com redução abertae fixação da placa dorsal, e vinte e oito pacientes foram tratadoscom redução aberta e fixação com parafuso. Depois de dois anos deacompanhamento, a média do escore AOFAS foi de 83,1 pontos nogrupo de fixação da placa dorsal e 78,5 pontos no grupo de fixaçãocom parafusos (p <0,01). Do grupo de fixação com placa dorsal, aanálise radiográfica revelou redução anatômica em vinte e nove pacientes(90,6%, 29/32) e redução não anatômica em três pacientes.Do grupo de fixação com parafuso, a análise radiográfica revelou reduçãoanatômica em vinte e três pacientes e redução não anatômicaem cinco pacientes (82,1%, 23/28). Conclusões: A redução abertae fixação com placa dorsal para lesão de Lisfranc deslocada têmmelhor resultado a curto e médio prazo e uma taxa de reoperaçãoinferior do que a técnica padrão de redução aberta e fixação interna(RAFI) com parafuso. Em nossa experiência, recomendamos o usode placa dorsal em RAFI nas lesões de Lisfranc deslocadas. Nívelde Evidência II, Estudo Prospectivo Comparativo...

The objective of this prospective study was to testwhether the treatment of Lisfranc injuries with open reductionand dorsal plate fixation would have the same or better functionaloutcomes as treatment with standard trans-articular screwfixation. Methods: Sixty patients with primarily isolated Lisfrancjoint injury were treated by open reduction and dorsal platefixation or standard screw fixation. The patients were followedon average for 31 months. Evaluation was performed with patients’chief complaint, clinical examination, radiography, andAOFAS Midfoot Scale. Results: Thirty two patients were treatedwith open reduction and dorsal plate fixation, and twenty eightpatients were treated with open reduction and screw fixation.After two years follow-up, the mean AOFAS Midfoot score was83.1 points in the dorsal plate fixation group and 78.5 points inthe screw fixation group (p<0.01). Of the dorsal plate fixationgroup, radiographic analysis revealed anatomic reduction intwenty-nine patients (90.6%, 29/32) and nonanatomic reductionin three patients. Of the screw fixation group, radiographicanalysis revealed anatomic reduction in twenty-three patientsand nonanatomic reduction in five patients (82.1%, 23/28).Conclusions: Open reduction and dorsal plate fixation for adislocated Lisfranc injury do have better short and median termoutcome and a lower reoperation rate than standard screw ORIF.In our experience, we recommend using dorsal plate in ORIF ondislocated Lisfranc injuries. Level of Evidence II, ProspectiveComparative Study...

Pre-tibial synovial cyst after reconstruction of the anterior cruciate ligament: case report.

Arthroscopic reconstruction of the anterior cruciate ligament has been modernized through new surgical techniques and new materials. When tibial fixation is performed using an absorbable screw, complications may occur, such as formation of a pre-tibial cyst. The case described here is about a patient who presented an anteromedial synovial cyst in his right knee, three years after having undergone ACL reconstruction. The patient did not present any pain nor any complaints other than a mass that progressively increased in size, worsened after physical activities. Imaging examinations were requested: simple radiography of the knee and magnetic resonance. Anteromedial imaging of the knee showed a mass with well-delimited borders and internal fluid content, suggestive of a synovial cyst, with communication with the joint cavity through the tibial tunnel, without presenting enlargement or absorption of the bone tunnel. The cyst was surgically resected and the tibial tunnel occlusion was performed using a bone plug. The diagnosis of a synovial cyst was subsequently confirmed through the results from the anatomopathological examination. The patient presented good clinical evolution, with disappearance of the symptoms and a return to physical activities.

A reconstrução do ligamento cruzado anterior (LCA) por via artroscópica vem sendo modernizada por novas técnicas cirúrgicas e novos materiais. Quando feita a fixação tibial com parafuso absorvível podem ocorrer complicações, como a formação de um cisto pré-tibial. O caso em questão é de um paciente que apresentou um cisto sinovial anteromedial em joelho direito três anos após ter sido submetido a reconstrução do LCA. O paciente não apresentava dor ou outras queixas, apenas massa de aumento progressivo, com pioria após atividades físicas. Foram solicitados exames de imagem: radiografias simples do joelho que não apresentavam alterações; e ressonância magnética com imagem anteromedial em joelho sugestiva de cisto sinovial. Apresentava bordas bem delimitadas e conteúdo líquido interno, com comunicação com a cavidade articular através do túnel tibial, sem apresentar alargamento ou absorção do túnel ósseo. Foram feitas ressecção cirúrgica do cisto e oclusão do túnel tibial com tampão ósseo, com posterior confirmação do diagnóstico de cisto sinovial após resultado do exame anatomopatológico. O paciente apresentou boa evolução clínica, com desaparecimento dos sintomas e retorno às atividades físicas.

Radiografias em inclinação lateral como fator preditivo da correção cirúrgica na escoliose idiopática do adolescente / Bending radiographs as a predictive factor in surgical correction of adolescent idiopathic scoliosis

OBJETIVO: Avaliar a utilização de radiografias com inclinação lateral ativa em decúbito dorsal como fator preditivo da correção cirúrgica da curva torácica principal em pacientes com escoliose idiopática do adolescente (EIA). MÉTODOS: Foram avaliados, clínica e radiograficamente, 20 pacientes portadores de EIA tipo Lenke 1A e 1B operados por via posterior, utilizando nas montagens apenas parafusos pediculares. A flexibilidade das curvas foi calculada através de radiografias em inclinação lateral supina ativa. Os valores obtidos no pré-operatório para a curva torácica principal foram incluídos em uma equação matemática proposta por Cheung et al com a finalidade de predizer o resultado angular esperado após a correção cirúrgica. Após isto, foi realizado estudo estatístico de significância entre o valor predito e o real pós-operatório. RESULTADOS: Houve significância estatística para todos os casos estudados em relação ao valor predito pré-operatoriamente e os achados radiográficos do pós-operatório imediato (p < 0,005). CONCLUSÕES: É possível prever a porcentagem de correção cirúrgica da curva torácica principal, em pacientes com EIA tipo Lenke 1A e 1B, utilizando radiografias pré-operatórias com inclinação lateral em posição supina.

OBJECTIVE: To evaluate the use of x-rays in dorsal decubitus, as a predictive factor for surgical correction of the main thoracic curve using pedicle screws, on patients with idiopathic adolescent scoliosis. METHOD: Twenty patients with idiopathic adolescent scoliosis of Lenke types 1A and 1B who were operated using a technique only involving pedicle screws by means of the posterior route were evaluated clinically and radiographically. The curve flexibility was calculated by means of active supine lateral oblique radiographs. The postoperative values for the main thoracic curve were included in a mathematical equation proposed by Cheung et al., with the aim of predicting the expected angular result from the surgical correction. The difference between the expected and actual postoperative results was then investigated regarding its statistical significance. RESULTS: There was statistical significance for all the cases studied, between the values predicted before the operation and the radiographic findings immediately after the operation (p < 0.005). CONCLUSIONS: It is possible to predict the percentage surgical correction of the main thoracic curve that will be achieved using pedicle screws in patients with idiopathic adolescent scoliosis of Lenke types 1A and 1B, by means of preoperative supine oblique radiographs.

BENDING RADIOGRAPHS AS A PREDICTIVE FACTOR IN SURGICAL CORRECTION OF ADOLESCENT IDIOPATHIC SCOLIOSIS.

OBJECTIVE: To evaluate the use of x-rays in dorsal decubitus, as a predictive factor for surgical correction of the main thoracic curve using pedicle screws, on patients with idiopathic adolescent scoliosis. METHOD: Twenty patients with idiopathic adolescent scoliosis of Lenke types 1A and 1B who were operated using a technique only involving pedicle screws by means of the posterior route were evaluated clinically and radiographically. The curve flexibility was calculated by means of active supine lateral oblique radiographs. The postoperative values for the main thoracic curve were included in a mathematical equation proposed by Cheung et al., with the aim of predicting the expected angular result from the surgical correction. The difference between the expected and actual postoperative results was then investigated regarding its statistical significance. RESULTS: There was statistical significance for all the cases studied, between the values predicted before the operation and the radiographic findings immediately after the operation (p < 0.005). CONCLUSIONS: It is possible to predict the percentage surgical correction of the main thoracic curve that will be achieved using pedicle screws in patients with idiopathic adolescent scoliosis of Lenke types 1A and 1B, by means of preoperative supine oblique radiographs.

Novo sistema para acoplamento de parafusos de interferência: ensaio biomecânico de torção / New coupling system for interference screws: biomechanical resistance to torsion

OBJETIVO: Apresentar um novo sistema de acoplamento solidário entre chave e parafuso de interferência, assim como ensaios biomecânicos que avaliem a segurança de sua utilização. MÉTODOS: O novo sistema foi submetido a ensaios biomecânicos de torção. Foram realizados dois tipos de análise: torque máximo de inserção manual dos parafusos em osso bovino; ensaios destrutivos de torção do sistema em máquina INSTRON 55MT. Os mesmos testes foram realizados em um grupo controle utilizando um sistema de acoplamento já disponível no mercado. (Acufex®) RESULTADOS: Nos ensaios de inserção em fêmures bovinos as médias de valores aferidos com torquímetro digital foram 1,958 N/m para Acufex® e 2,563 N/m para FMRP. Considerando p<0,05, não houve diferença significativa (p=0,02) nos valores de torque máximo de inserção nos dois sistemas estudados. Os valores médios de torque máximo para deformar o parafuso foram de 15 N/m para o parafuso Acufex® e 13 N/m para o parafuso FMRP, portanto, sem diferença estatística (p>0,05). Ao avaliar a deformação angular, não houve diferença significativa entre os grupos de parafuso (p=0,15). CONCLUSÃO: O novo sistema de acoplamento para parafusos de interferência desenvolvido na FMRP-USP revelou resistência à torção comparável a sistema já disponível no mercado e regulamentado para uso internacional.

OBJECTIVE: To introduce a new coupling system between screw driver and interference screw, and biomechanical tests that validate the safety of its application. METHODS: The new system was submitted to biomechanical torsion assays. Two types of analysis were performed: maximum torque of manual insertion of the screws into bovine bone; destructive assays of torsion of the system using an INSTRON 55MT machine. The same tests were also performed on a control group, using a commercially available interference screw coupling system (Acufex®). RESULTS: In the tests on manual insertion of screws in bovine femurs, the average values found with a digital torque meter were 1.958 N/m for Acufex® and 2.563 N/m for FMRP. Considering p>0.05, there were no statistical differences between the two groups (p=0.02) in the values for maximum torque of insertion, in the two systems studied. The average values for maximum torque of torsion resisted by the screw were 15N/m for the Acufex® screw and 13N/m for the FMRP screw, again with no statistical differences between the two groups (p>0.05). In the evaluation of angular deformation, there was also no significant difference between the two screw types (p=0.15). CONCLUSION: The new coupling system for interference screws developed at FMRP-USP revealed a torsion resistance that is comparable with the system already available on the market and regulated for international use.

Avaliação biomecânica da influência do macheamento e do desenho dos parafusos cervicais / Biomechanical evaluation of the influence of cervical screws tapping and design

OBJETIVO: Avaliar a influência do desenho do parafuso (autoperfurante e automacheante) e do macheamento do orifício-piloto sobre o torque de inserção e a força de arrancamento dos parafusos utilizados para a fixação anterior da coluna cervical. MÉTODO: Quarenta parafusos automacheantes e 20 autoperfurantes foram inseridos em 10 modelos artificiais de osso (blocos de poliuretana) e 10 vértebras cervicais de carneiro. Os parâmetros estudados foram o torque de inserção e a força de arrancamento. Foram formados três grupos experimentais de acordo com o tipo de preparo do orifício- piloto e o tipo de parafuso utilizado: grupo I - parafuso automacheante com orifício- piloto perfurado e macheado; grupo II - parafuso automacheante com orifício perfurado e não macheado; grupo III - parafuso autoperfurante sem perfuração prévia do orifício- piloto e sem o macheamento. Nos grupos I e II a perfuração do orifício-piloto foi realizada por meio de broca de 3mm de diâmetro e o macheamento, com 4mm. O torque de inserção foi mensurado durante a implantação dos parafusos e, em seguida, foram realizados ensaios mecânicos em máquina universal de testes para avaliar a força de arrancamento dos parafusos. RESULTADOS: O macheamento e a perfuração do orifício- piloto reduziram significativamente o torque de inserção e a força de arrancamento. CONCLUSÃO: O torque de inserção e a força de arrancamento dos parafusos autoperfurantes foram significativamente maiores quando comparado com os dos parafusos automacheantes inseridos após o macheamento do orifício-piloto.

OBJECTIVE: To assess if the screw design (self-drilling/self-tapping) and the pilot hole tapping could affect the insertion torque and screw pullout strength of the screw used in anterior fixation of the cervical spine. METHODS: Forty self-tapping screws and 20 self-drilling screws were inserted into 10 models of artificial bone and 10 cervical vertebrae of sheep. The studied parameters were the insertion torque and pullout strength. The following groups were created: Group I - self-tapping screw insertion after pilot hole drilling and tapping; Group II - self-tapping screw insertion after pilot hole drilling without tapping; Group III - self-drilling screw insertion without drilling and tapping. In Groups I and II, the pilot hole had 14.0 mm in depth and was made with a 3mmn drill, while tapping was made with a 4mm tap. The insertion torque was measured and the pullout test was performed. The comparison between groups was made considering the mean insertion torque and the maximum mean pullout strength with the variance analysis (ANOVA; p< 0.05). RESULTS: Previous drilling and tapping of pilot hole significantly decreased the insertion torque and the pullout strength. CONCLUSION: The insertion torque and pullout strength of self-drilling screws were significantly higher when compared to self-tapping screws inserted after pilot hole tapping.

BIOMECHANICAL EVALUATION OF THE INFLUENCE OF CERVICAL SCREWS TAPPING AND DESIGN.

OBJECTIVE: To assess if the screw design (self-drilling/self-tapping) and the pilot hole tapping could affect the insertion torque and screw pullout strength of the screw used in anterior fixation of the cervical spine. METHODS: Forty self-tapping screws and 20 self-drilling screws were inserted into 10 models of artificial bone and 10 cervical vertebrae of sheep. The studied parameters were the insertion torque and pullout strength. The following groups were created: Group I-self-tapping screw insertion after pilot hole drilling and tapping; Group II-self-tapping screw insertion after pilot hole drilling without tapping; Group III-self-drilling screw insertion without drilling and tapping. In Groups I and II, the pilot hole had 14.0 mm in depth and was made with a 3mmn drill, while tapping was made with a 4mm tap. The insertion torque was measured and the pullout test was performed. The comparison between groups was made considering the mean insertion torque and the maximum mean pullout strength with the variance analysis (ANOVA; p≤ 0.05). RESULTS: Previous drilling and tapping of pilot hole significantly decreased the insertion torque and the pullout strength. CONCLUSION: The insertion torque and pullout strength of self-drilling screws were significantly higher when compared to self-tapping screws inserted after pilot hole tapping.

Influência do diâmetro do orifício piloto na resistência ao arrancamento dos parafusos do corpo vertebral / The influence of pilot hole diameter on screw pullout resistance

Foram realizados ensaios mecânicos com o objetivo de avaliar a influência do diâmetro do orifício piloto em relação ao diâmetro interno do parafuso na resistência ao arrancamento dos parafusos do sistema de fixação vertebral aplicados no corpo da vértebra. O estudo foi realizado em duas etapas. Na primeira etapa foram utilizados corpos de prova de poliuretana para a colocação de parafusos de 5mm e, 6mm , e na segunda etapa os parafusos foram inseridos na face lateral dos corpos das vértebras lombares de suínos. O orifício piloto foi realizado com brocas de diâmetro menor, igual ou maior que o diâmetro interno do parafuso. Foram realizados ensaios mecânicos de arrancamento em máquina universal de teste para a avaliação da força máxima de arrancamento dos implantes. Foi observado que o diâmetro do orifício piloto em relação ao diâmetro interno do parafuso influencia na resistência ao arrancamento dos implantes.

Mechanical assays were performed in order to assess the influence of pilot hole diameter versus screw's inner diameter on screw pullout resistance in the vertebral fixation systems applied to the vertebral body. The study was conducted in two stages. In the first, polyurethane test bodies were used for placing 5 and 6 mm screws, and, in the second stage, the screws were inserted into the lateral surface of the lumbar vertebral bodies of pigs. The pilot hole was built with drills with smaller, similar or larger diameter than screws' inner diameter. Mechanical pullout assays were performed using a universal test machine for the assessment of maximum pullout screw resistance. The diameter of the pilot hole versus screw's inner diameter was shown to influence screw pullout resistance.